Search Documents

By M. J. Zdunczyk

Located approximately 50 miles northeast of Knoxville, Tennessee, Short Mountain Silica mines the Clinch Formation, an orthoquarzite, for silica sand. In 1980, a Knoxville resident and area contractor visualized mining Short Mountain for silica sand. Because APG Industries, the main market for the glass sand product, was only 48 kilometers from the site, many silica sand companies became interested in the property. In 1986, J.D. Nicewonder began to develop the site, and in May of 1988, APG Industries received the first sand shipment.

Jan 1, 1992

By D. Lawrence, H. Lawrence, G. Saevil

Plant operators in the mineral processing industry have been implementing expert systems for several years now, with the intent to increase production and reduce costs. Most systems have been installed on grinding circuits of some type and have proven that the technology is viable in that application. However, few applications on other processes have been attempted for various reasons, such as lack of reference sites, complexity of the process, lack of suitable measurements and lack of confidence in the technology. The successful application of an expert system on an Alumina Calcining kiln is the first such application in the West Indies Alumina Company (Windalco), and demonstrates how this technology can be successfully applied to other processes. The key objective of an expert system is to optimize the process. To achieve this the process must first be stabilized, followed by optimization of the operating parameters. The steps taken by this expert system to optimize the process are: • Check for abnormal conditions and deal with them using a prioritized set of special actions. • Use a selection of rule blocks to stabilize the process. • Once the process is stable, achieve additional benefits through further optimization of the process. The potential benefits that a user can expect to achieve through installing an expert system can be assessed on the basis that performance will improve from that of an "average operator" to that of the "best operator" performing at his optimum for 24 hours a day, every day. The quantifiable process benefits include: • Increased production • More consistent product quality • Reduced operating costs • Reduced standard deviation of key variables • Consistent plant operation The success of this project was measured in several ways: project implementation, realised economic benefits, and realised non-economic benefits. With a commitment to maintain the system over the long term, the longevity of the system is assured and will become an important part of the Alumina Calcining control strategy at Windalco. This paper discusses the various phases of implementing the ABB Expert Optimizer expert system, what the benefits were and the procedure that is in place to maintain the system to ensure continued long term success.

Jan 1, 2002

By W. A. Forbes

by the combustion of this gas as it reached the air was a familiar sight in the days when open-top furnaces were in vogue. As blast-furnace practice progressed, however, involving the use of hot blast and the development of power from the gas, blast-furnace construction was modified to conserve this gas for heating hot-blast stoves, raising steam under boilers, and various miscellaneous purposes. When the use of blast-furnace gas was extended to the driving of gas engines, the necessity for thoroughly cleaning the gas became apparent., and soon the advantages of also properly cleaning the gas for use in stoves and udder boilers became more fully recognized.

Jan 10, 1913

By Euler De Souza, Kyle Penner

"Booster fans play an important role in assisting main fans by boosting the air pressure of the ventilation air passing through it. The correct placement of underground booster fans in a mine is a critical decision since it not only influences the mine’s operational capacity in terms of costs and efficiency, but also affects safety and environmental conditions. There are many booster fan installations around mines that are inappropriate, in some cases resulting in system failure (fan stall) or in a major negative impact on mine production. Inadequate booster fan placement has resulted, in some cases, in extensive air leakage which has compromised the economics of the operation and, in other cases, in recirculation of contaminants which has seriously compromised safety. This paper provides guidelines for proper design and siting of booster fans underground, to not only achieve an economic ventilation system but to create safe work conditions and efficient atmospheric conditions. Procedures for the planning, installation, operation and maintenance of booster fans are also presented. A case study illustrating the design and siting of a major booster fan installation in a potash mine, supported by computational fluid dynamics analysis, is presented.INTRODUCTIONIn large underground operations with complex ventilation networks offering high resistances, the never ending increased required quantities of air can almost only be supplied through use of high pressure main fan systems. These fans may, in effect, induce significant leakage losses in the system, having a negative impact on safety performance. In such cases, booster fans can be designed to decrease the main fan pressures and reduce the leakage flows, improve system efficiency and reduce costs. In well designed systems, booster fans can thus be used to redistribute the airflow and assist the main surface fans.When the pressure supplied by the main fans is insufficient to meet the ventilation circuit pressure requirements, booster fans are placed in strategic locations where pressure boosting is essential. Booster fans are typically sited in sections of the circuit offering high ventilation resistance and requiring this form of ventilating air motivation. Booster fans are thus required when the mine expands, and so the resistance of the ventilation network, and the primary fans no longer can supply the required pressure and flow."

Jan 1, 2019

By Pedro Lilienfeld

This report describes a program to develop, design, fabricate and subject to environmental testing three prototype collection-sensing devices of an eventual mining-machine mounted automated monitor for the measurement of the respirable fraction of coal mine dust to determine both short-term as well as average mass concentrations over typical 8-hour shifts. The design of this instrument is based on collection by filtration and mass sensing by beta-radiation attenuation. The emphasis of this development program was to evolve a rugged, stable and reliable collection-detection head compatible with the environment to which An eventual monitor will be subjected. Laboratory testing of this prototype instrument was performed over a representative range of temperature, humidity, dust concentration and composition, shock and vibration. The results of this testing program indicated that the operation of the prototype version His compatible with these environmental conditions and that further development of this configuration into a field operational device is justified.

Jan 1, 1977

By W. J. Wuest

This U.S. Bureau of Mines report presents an overview of ground control considerations associated with cutter roof failure. Many of the relevant U.S. and international research studies since the late 1940's are reviewed, and summaries of recent design guides are included. Factors affecting cutter roof, such as underground stress field and rock structure around the entry, are described. Strata control techniques are also outlined. These techniques are divided into three sections: artificial support, mine structure design, and multiple-seam extraction. Other subjects covered in the report include monitoring and prediction, effect of geologic features, and mapping of adverse mining conditions. The emphasis of this report is on practical considerations; theoretical discussions are minimal.

Jan 1, 1994

By S. Hoskins, S. Chiovelli

"The annual budget for the repair and maintenance of equipment at Syncrude Canada Ltd. is in excess of $450 million. Of this amount, a significant portion can be attributed to the loss of material on various pieces of equipment throughout the operation. In order to effectively battle the different wear and corrosion mechanisms that lead to material loss, it is important to understand how materials behave in the environments in which they are used. Through the work carried out at Syncrude, and work conducted with various external collaborators, significant improvements in both equipment reliability and productivity have been achieved. This paper will review some recent field trials where materials research has demonstrated the potential for significant improvements in equipment run life and reduced maintenance costs. These field trials will demonstrate the need for understanding the interaction between various damage mechanisms and the materials used in different services. The paper will also discuss current areas of focus along with future directions for further work. IntroductionSyncrude Canada Ltd, located in northern Alberta, Canada, operates a mining, extraction, and upgrading facility that removes bitumen from oil sand to produce synthetic crude oil. Oil sand is mined from the orebody using conventional open pit mining techniques. Recently, the mining scheme has changed from a dragline/bucketwheel/conveyor system to a shovel/truck/crusher/hydrotransport operation as depicted in Figure 1. Since the start of production in 1978, the identification, development and application of wear protection has been an ongoing challenge due to the abrasive nature of the oil sands and the massive volumes of materials that are moved. The use of various materials and application processes along with component design modifications has resulted in significant improvements in both productivity and reliability (Adamic et al., 1995; Llewellyn, 1996, 1997; Anderson et al., 1998; Chiovelli et al., 1998).In an effort to continuously improve the operation, Syncrude has been quick to adopt new wear technologies. As seen in Figure 2, since the start of operation, a variety of materials have been used to increase wear performance and ultimately equipment reliability and availability. Although Figure 2 does not show a time axis, the bottom axis may also be used to represent a time progression for the predominate use of these materials at Syncrude. Tungsten carbide metal matrix composite (WC-MMC) overlays are currently the materials of choice for most of Syncrude’s critical production applications. Metal matrix composite overlay technology has potential for significant improvements and Syncrude is actively working with powder consumable manufacturers to advance this technology."

Jan 1, 2004

By Joseph A. Vanous

The inductive communication system was developed under this contract for use in the hoist of deep mines. This program was a four phase program with experimental dual frequency equipment resulting from Phase I, emergency single frequency equipment developed under Phase II, and equipment documentation required under Phase III. An additional emergency system was provided under Phase IV.

Jan 1, 1976

By Paul Meadows

The Buckrange reservoir, Stephens field, Ark., is approaching the economic limit of production under present operating conditions. Over 100 million barrels of oil remaining in the reservoir will not be recovered by primary producing methods. The Bureau of Mines, in cooperation with the Arkansas Oil and Gas Com-mission, made the petroleum-engineering study presented in this report to aid operators in evaluating secondary-recovery possibilities in the reservoir and in planning secondary-recovery programs if their initiation is decided. The Stephens field, in Columbia, Nevada, and Ouachita Counties, Ark., is about 12 miles northeast of Magnolia, Ark., and 15 miles west of the Smackover field. Surface elevations in the area average about 240 feet above sea level.

Jan 1, 1956

By G. E. Burpee

A COMPREHENSIVE study of insoluble residues in the productive Permian limestone in the Hobbs and Eunice fields, Lea County, N. M., has been conducted by Shell Petroleum Corp. engineers {luring the past two years. This study was prompted by the belief that the stratigraphy of the producing formation might be worked out in detail and that some relationship might be established between the permeable oil, gas, and water zones and correlatable lithologic horizons within the productive formation. As a result of the study, correlations have been established which have proved of great value to both an orderly development and corrective program.

Jan 1, 1935

By Y. FUJII, E. CHANDA, J. KODAMA, D. FUKUDA, M. NISHIHARA, Y. NAKAYAMA, P. SINKALA

For over 40 years, Mufulira underground copper mine has been recording incidents of rockburst. Laboratory tests and numerical analyses were carried out to understand the rockburst mechanism at the Mufulira mine. Rockburst did not occur in the chain pillars or at the mining face, but mainly in the mining drives along diminishing pillars or ahead of the mining face. RQD suggested that the rock mass in the rockburst areas was relatively intact. Laboratory tests confirmed that the rock at Mufulira mine is very strong and brittle. Elastic stress analyses for the rockburst sites by 3D displacement discontinuity method (DDM) indicated very high stress in the chain pillars and low-stress concentration at the sites of rockburst during the initial mining stages. However, there was no apparent positive correlation between the elastically calculated normal stress values and the occurrences of rockbursts. The 2D elastic FEM analysis was conducted under the concentrated stress by DDM and indicated that some stress increase with face advance for the rockburst in the vicinity of the mining face. However, stress severity indicated almost no increase, and the rockbursts cannot be explained as an instantaneous rock mass failure due to stress increase by mining. Therefore, a creep damage model was proposed to clarify the mechanism of the rockbursts. Cumulative rock damage was evaluated for the edge elements of each sidewall of the mining drives, based on the normal stresses by 3D DDM. The rockburst occurrences were well hindcasted. A method to estimate the volume of the rockburst source was proposed, and a likely result was obtained.

Aug 12, 2022

By Maria I. De Rosa

High temperatures encountered by mine rescue teams during emergency situations may cause severe physiological strain, hindering the men from carrying out rescue and recovery missions. A prototype ice-cooling garment (ICG) was developed by the Bureau of Mines to alleviate physiological strain due to heat stress. The effectiveness of the garment was tested with acclimatized and unacclimatized subjects at a typical work rate (1,200 Btu/hr) expected during rescue operations and at various hot environments (97° to 113° F dry bulb and 80° to 89° F wet bulb). During exposures with the ice cooling garment, the subjects were able to maintain a safe deep body temperature of 100.4° F or below Without the garment, the deep body temperature rose beyond values of 100.4° F, a condition considered unsafe for continuous work in hot conditions. Both heart rate and skin temperature values were lower while wearing the ICG. Subjective observation also indicated a marked benefit by wearing the ICG.

Jan 1, 1976

By C. Harold Riches

This article is directed co a commentary on the patent system in its relation to the public interest. As man gained supremacy over his environment, he could devote progressively increasing portions o his time to improving his standards of living. In the history of the human race, we have advanced from the hollowed floating log to the modern steamship of the present age; from the sickle and flail to the reaper and combine; from the trumpet and drum as a means of communication co the telegraph, telephone, and radio; from the horse and ox cart to the automobile, truck, aeroplane, and train; and so on ad infinitum through the list of inventions on which are based the industrial and political economies and standards of living we enjoy today. It has also been a long road from the day of the alchemist and his closely guarded secrets to the era of the patent system and its storehouses of knowledge open to the world. The alchemist and the craft and merchant guilds closely guarded their secrets. In fact, they largely opposed innovations on the grounds that they might injure profits and restrict employment. In these days of unrest, with great clamour out of doors for radical changes in our political and industrial economies, it may not be untimely to examine one of the keystones which support the economic structure we know as the free enterprise system, the system which is predicated upon the right of the individual to own property. Many, through impractical idealism, ignorance, confused thinking, or blind political prejudice, advocate the substitution of ownership by the State ? for the right of ownership by the individual. As civilization has advanced to the high standards of living we enjoy today through the efforts of a comparatively few inventors, the patent system which has provided the incentive that created the inventions on which our industries and our employment are based is fully understood and appreciated by a comparatively small percentage of our people. As a result, the patent system, as a keystone in our free enterprise economy, is an apt target for destructive criticism, with the thought, possibly, that by eliminating or drastically restricting the several rights to individual ownership one by one, ownership by the State will progressively replace ownership by the individual.

Jan 1, 1949

By T. V. Ramey

Heap leaching in certain parts of the world, such as Chile's Atacama Desert, brings unique design problems in the form of possible large differential settlements of the foundation soils due to the dissolution of salts in northern Chile the soils often contain very high concentrations of soluble salts (nitrates, potassium, magnesium, and common sodium). When a leak in the liner occurs, the escaping solution dissolves these salts and triggers differential settlement. If the settlement is great enough, the geo-membrane tears, the leakage increases, triggering more differential settlement. The nitrate plants have experienced many occurrences of this phenomenon where a brine pond will undergo a sudden and complete loss of the impounded liquors. The authors present a simplified technique to quantify the differential settlement resulting from dissolution and provide a method which can be used to select a geo-membrane with suitable flexibility under axi-symmetric (multi-axial) load conditions to tolerate the predicted settlement. (This paper was previously published for Randol Gold Forum 1996 [Ref. 6]).

Jan 1, 1997

By B. F. Giyani, A. Salama

Tanzania is a country with a variety of mineral deposits, including metallic minerals, gemstones, mineral fuels, industrial minerals, and critical minerals. This study provides an overview of mining legal framework, mineral occurrence and production, challenges in the mining sector, and government initiatives. The aim is to demonstrate the development of the mining sector in Tanzania and explore the potential for further mining investment in the country. The mineral production data showed generally increasing trends over the years, for example, gold production increased from 42 tonnes in 2018/2019 to around 50 tonnes in 2023/2024. Despite the growth, the mining sector encounters several challenges, including a lack of detailed geological information on mineral deposits, inadequate infrastructures in some remote mining sites, the existence of informal artisanal miners, and mineral smuggling. The Tanzanian government has introduced several initiatives to address these challenges, including carrying out the highresolution airborne geophysical survey to increase geological information in some areas, the formalisation of artisanal and small-scale mining, establishing mineral markets to combat mineral smuggling, and encouraging mineral value addition within the country.

Oct 24, 2025

By M. S. Frasad

The State of Minnesota is interested in stimulating the development of clay resources and recently supported a two year project to collect data on geological, mineralogical, processing, economic and environmental aspects of such potential developments. This paper presents the .various process options adopted on the bulk samples collected from the Minnesota River Valley area which is a primary deposit and contains a major silica fraction. A standard test flowsheet involving degritting, dispersion, HGMS, and cycloning was developed and for some samples yielded an acceptable filler grade product. Secondary streams containing relatively high grade kaolin but of coarse size were also obtained. Improvement in particle size distribution and in physical properties related to paper product specifications (brightness, viscosity) were obtained by size reduction processes. Market and economic considerations for kaolin consumption in the upper Midwest are analyzed. Current markets for paper grade kaolin in Minnesota were briefly discussed.

Jan 1, 1990

By Hideo Nakae, Hideki Yamaura, Toshiaki Kimura

"In 1968 J. N. Reding et al. suggested processes for fabricating composites. According to their patent, decompression atmosphere, which occurs during the reaction between magnesium and oxygen and/or nitrogen in the closed system, causes the spontaneous infiltration of melt into narrow spaces such as ceramic preforms. However, they did not report the proof of this phenomenon or the industrial manufacturing method. Therefore, this research measured the pressure change among SiC particles surrounding molten aluminum. As a result, the pressure reduction during the Mg reaction was identified. Moreover, the existence of Mg3N2, which improves the wettability between Al alloy melt and SiC particles on the interface, was observed on the surface of particles. Applying these two phenomena, a new process for the manufacturing of cast discontinuously reinforced aluminum composites (DRA) was developed. This new method is expected to produce DRA without additional pressure.IntroductionWith the increasing demands for light-weight materials in the automotive and aerospace industry in recent years, ceramic particulate reinforced aluminum matrix composites called DRA (Discontinuously Reinforced Aluminum Composite) have been receiving significant attention because of its lightness, superior abrasion resistance, high heat conductivity and low thermal expansion [1-3]. Consequently, DRA was considered for electronic parts such as heat-sinks or a base for power semiconductors, and began to be applied for automotive parts including brake drums, discs, cylinder liners, pistons and so on [4- 6]. However, high machining cost is one of the significant barriers to widespread use ofDRA. One solution to this problem is the adoption of cast DRA that can be produce to near-net shape, reducing machining cost."

Jan 1, 2000

By G Hart

As the iron ore/magnetite boom gains momentum, it is particularly important to question established past trends and explore the potential of alternative design options. Traditionally, ‘rule of thumb’ methods have been used to size dewatering equipment. Greater consideration needs to be given to technological advancements and specific throughput testing of each ore body type based on innovative developments.This paper will describe how an innovative approach resulted not only in significant savings in capital cost and site work hours but also delivered a truly optimised design for the thickener duty at Karara. Test work also played a crucial role and a comprehensive test work program on the ore samples showed the scale-up benefi ts of new technology in thickener designs. Working closely with the Karara team during the laboratory testing proved the old sizing theories for iron ore/magnetite processing have been superseded with the knowledge and results of the industry’s newest feedwell technology. Increased solids flux and rise rates in the testing process proved very successful, resulting in signifi cantly reduced thickener sizes and lower capital expense.Mechanical design considerations such as removal of underflow and pump access led to a preference for an above-ground thickener confi guration, and the economics of a completefabrication and installation package favoured steel construction for the thickener units.The ultimate choice of the bolted/fl anged tank methodology provides both economic and timely solutions for the site installation including reduced man power and quick and safe site-work. A benefits comparison between this design and other fabrication and installation procedures will also be analysed in the paper.

Jul 11, 2011

By W. Fergusson

This paper takes a look at the use of rubber to provide corrosion resistance and wear resistance in the mining industry. The longer life and reduced down time involved with the use of rubber are stressed, and examples are given of applications in grinding mills, skips, discharge chutes and screens.

Jan 1, 1979

By Robert J. Uffen

YOU will likely recall the accomplishments of the International Geophysical Year of 1957, with its polar expeditions, the discovery of the Van Allen radiation belts and the spectacular launchings of the first artificial earth satellites. Our know ledge of the exterior of the earth was greatly increased by this international, friendly, cooperative scientific investigation. The Inter-national Union of Geodesy and Geo-physics has now been joined by the new International Union of Geological Sciences in sponsoring a similar study of the earth's interior. The program will extend from January, 1962 until December. 1964, and is known as the International Upper Mantle Project. During the T.G.Y studies of the interior of the earth were relatively neglected, even though the same international •Cooperation in obtaining simultaneous world-wide observations, by similar instruments, is required to locate and study earth-quakes, for example, as it is to study the earth's upper atmosphere. The upper mantle is 1•emote from man, as it extends from a depth of about 10 km. to perhaps 1000 km., but its practical importance is great.

Jan 1, 1962