Search Documents

By Cleber Caetano Thomazi

Rotary kilns are continuous process equipment used on calcining of nickel ore. The chemical and physical reactions are created by means of heat up the material to predetermined temperatures. Tertiary air fans are attached to the kiln shell to maintain oxidizing/reduction conditions. Special ducts orientate the air flow inside the kiln. In the present work, two types of failure on distinct tertiary ducts mounted on the same kiln are reported. Chemical analysis, hardness test, metallographic and fractographic examinations were carried out. Fabrication related problems and creep were identified as the root causes of damages.

Oct 30, 2017

By Clifford B. Farris

The natural cementation strength of retorted oil shale is the focus of this investigation. The optimum retorting temperature and residence time to obtain natural cementation strength in retorted Green River oil shale from western Colorado were determined as follows: [Optimum Conditions for Natural Cementation Maximum Residence Obtained Retorting Time at Compressive Mode of Temperature Temperature Strength' Retorting °F °C hr psikg/cm-2 Direct 1,520 822 2.0 270 19.0 Indirect 1,530 832 2.9 325 22.8] 1 Scattered samples were tested at strengths as high as 463 psi (32.6 k /cm 2) (Run 8, indirect mode) and 406 psi (28.5 kg/cm2) (Run 48, direct mode), but these high strengths were not confirmed by nearby tests. Minus 0.5-inch (1.3-cm) Green River oil shale was heated in a differential retort under conditions simulating potential full-scale retorting processes. The variables investigated were retorting temperature, residence time, retorting mode, and shale grade. Samples of the retorted Green River oil shale were moistened to optimum plus 2% (25%) moisture, compacted to 95% Proctor density, sealed and cured at 100°F (38° C) for up to 40 days. Lower curing temperatures, which are likely in the field, would probably result in significantly slower development of cementation strength, and might lower the ultimate strength developed. However, these effects were not studied in this project. The cured samples were tested for compressive strength, and correlative equations were developed for the increase of compressive strength with curing time as a function of retorting temperatures and residence time. Petrographic analysis indicated that the cementing mechanisms may be the interlocking growth of acicular hydrated calcium aluminum sulfate crystals between the contacts of retorted shale fragments. Samples of the retorted shale were also tested for optimum Proctor density and moisture. Permeability and quality of the leachate of shale from typical runs were determined. The effect of use of retort rather than tap water on compressive strength and leachate after curing was determined. The retorted shale effectively filtered several mineral constituents from the retort water.

Jan 1, 1979

By T. S. Kagogo

The factors affecting haul truck tyre performance and the effectiveness of the management system at Rossing Uranium Mine were investigated with the aim of increasing tyre performance in terms of running hours until failure. The main objectives were to identify the types of tyre failure, their causes and cost implications, and evaluate the effectiveness of the management system. A site severity survey, weight study, and TKPH studies were conducted to determine the pit conditions, and an analysis of failed tyres carried out. The results showed that tyre performance at the mine has declined from 2009 to date, and the increase in lost value amounted to R5.7 million in 2012 alone. The main cause of tyre failure is loose rocks in the pit. The present management system in the load and haul department is not effective enough due to operational constraints it is facing.

Jan 1, 2014

By R. J. McClincy

The potential techniques for the direct smelting of copper sulfide concentrates to blister copper were evaluated from the standpoint of commercial application. Many existing smelters are adaptable to direct smelting practice but only with improved control of metallurgical performance. Modified and innovative procedures for slag cleaning and metal refining, prerequisites to direct smelting, are presented and discussed. The ability to smelt directly to blister copper using existing equipment and eliminating the need to convert matte offers ,significant advantages to traditional smelting practice from the viewpoint of cost, 'S02 control, and process simplicity.

Jan 1, 1983

By Jan Visman, S. J. Aresco

INTRODUCTION The accurate sampling of coal, as with most minerals, is a difficult task. Coal is a heterogeneous material made up of different types of coal and varying amounts of mineral matter. The product as mined may contain all the layers of coal and impurities found in the seam as well as portions of the stratas above and below the coal seam. The preparation plant is the device to size, crush, and/or remove impurities so the coal may be shipped as a salable product. Sampling may be needed at many stages in the preparation process. Although this chapter is primarily concerned with sampling in connection with preparation processes, the principles apply to all coal sampling. The main reasons for sampling in connection with coal preparation are: 1) To determine the washability characteristics of the raw coal by means of float and sink tests. These may be used for the design of a preparation plant, prediction of results to be obtained, or monitoring raw coal delivered to the plant. 2) To check the performance of various operating units in the plant, either by float. and sink tests or chemical analyses. 3) To determine the analytical characteristics of the products produced, such as moisture, ash, Btu, sulfur, etc. HISTORY The earliest accepted methods of sampling coal in the United States were given in US Bureau of Mines (USBM) publications by J. A. Holmes,l G. S. Pope,2 and A. C. Fieldner.3 The American Society for Testing and Materials (ASTM) more or less adopted the methods proposed by USBM in their Standard D-21-1916 and it remained a standard for many years. Briefly, this standard called for a 500 lb (227 kg) sample for coals less than 94 in. (19 mm) in size and a 1000 lb (454 kg) sample for all coals over 94 in. (19 mm) in size. No mention was made of increments, but there was an instruction that the sample should spread over the coal

Jan 1, 1979

By GEORGE D. RAMSAY

ABOUT three miles west of Fontana San Bernardino County, California, and fifty miles east of Los Angeles, the Kaiser Co., Inc., has built an integrated steel plant. By integrated, I mean that from its wholly owned iron ore and coal supply, the Kaiser Co. is producing in its own mills iron and steel products. Pig iron to meet the West Coast needs has been produced at Fontana since Jan. 1, 1943; steel ingots were first poured there May 14, 1943; and steel plate for ships was first rolled Aug. 15, just sixteen months after ground was broken. Briefly, the plant consists of: (I) Two batteries of by-product coke ovens, totalling ninety ovens, carbonizing about 1740 tons of coal per day at capacity; with by-product facilities for the production of tar, ammonia, and ammonium suIphate, light oil distillates, and tar distillates. (2) One blast furnace producing at

Jan 1, 1944

By Vince Saporito

Miners work in dangerous terrain, around the clock, with heavy equipment. Is there room for improvement in safety and standardization in the mining industry? Recent history would suggest there is a need for action. At a 2011 Spring Thaw conference in Denver CO, one speaker commented, ?We are having a number of incidents with workers getting ?pulled? into rollers or ?trapped? at transfer points when trying to manually clean (it) while the conveyor is still in motion.? It?s a troubling thought. These actions are specifically prohibited under U.S. Mine Safety and Health Administration (MSHA) regulation 57.14202. Another official from MSHA earlier this year indicated with today?s technology and policies presently in place, ?we should not be repeating the same incidents and violations year after year as we currently do.? But we are doing exactly that.

Jan 1, 2012

By Chas. F. Jackson

This bulletin is one of a series of Bureau of Mines reports dealing with mining methods, practices, and costs. A study of this subject was undertaken by the Bureau in cooperation with a large number of mining companies in 1928. This study continued for 5 years, during which engineers of the Mining Division of the Bureau visited most of the larger mines and many smaller ones in the United States, as well as several mines in Canada and Mexico. As a result of this study, 75 reports dealing with underground mining methods and costs at different mines were published as information circulars. Circulars also were issued on 6 open-pit mines and 2 gold-dredging operations. These circulars were written by the managers, superintendents, and engineers in charge of the operations, in some instances in collaboration with Bureau engineers. They were prepared according to a standard outline drawn up by the Bureau to obtain uniformity in textual treatment and in the arrangement and basis of setting up cost and operating data.

Jan 1, 1936

By Bob Drew, Goran Vukovic, Bojan Zivanovic, Klaus Gamweger

Reaction bath temperature is a major factor in processing liquid metals and in many applications where a balance between process duration and temperature has to be found to run a procedure efficiently. Also extremes of temperature can decrease the output of a process if too cold or even make it impossible, conversely overheating can be detrimental to both the product and furnace integrity. With the help of the new online temperature measurement system very accurate monitoring of the process is possible in contrast to the current routine practice where the temperature is measured periodically with dip thermocouples. The system works with a digital, fiber optic pyrometer, which is embedded in a refractory housing. Installation in the lining is possible below liquid level as nitrogen is blown to keep the system open and to ensure continuous sight from the optical head of the pyrometer to the molten metal through the tuyere. This permanent temperature measurement gives optimal process control with the potential of taking appropriate actions at an early stage enabling proactive process control. Therefore energy savings and even process endpoint detections can be realized.

Jan 1, 2015

By ALEC CROWELL

Mississippi has had oil production for only the past six years and natural gas production of minor magnitude since' 1926. The search for oil and gas commenced in 1903 and 1496 wells had been drilled in search of oil and gas up to Jan. 1, 1946. As the year 1945 ended, 659 wells were producing oil and gas from 23 separate reservoirs. The production for the year was 8,353,719,000 standard cubic feet of natural gas measured on a pressure base of 15.025 lb. per sq. in. abs., 15.316,009 bbl. of oil¬field water and 19,093,766 bbl. of crude oil and condensate. Production for the year 1944 was 2,636,067,000 standard cubic feet of gas, 14,979,793 bbl. of salt water and 16,420,346 bbl. of crude oil and condensate.

Jan 1, 1946

By Open-Hearth Steel

I received a telegram yesterday from Mr. J. H. Nead saying that he regretted circumstances had come up which prevent his attending the meeting, but that arrangements have been made and Mr. T. S. Washburn, of Inland Steel, will act as the Co-Chairman in his stead. We are sorry, of course, that he cannot be here at this conference. We have, therefore, asked Mr. James J. Bowden, chief metallurgist of Republic Steel Corporation, Cleveland, to act as Chairman and Mr. Tom Washburn to act as Co-Chairman. I will turn the meeting over to these gentlemen at this time.

Jan 1, 1940

By Mark S. Sanders

This report is a review and synthesis of the published literature dealing with personal equipment items used by low seam coal miners. This report reviews the following items of equipment: headgear, outer garments, respirators, cap lamp, gloves, knee pads, footwear, boots, helmets, ear protection, eye protection. Recommendations for further research and development are included.

Jan 1, 1978

By D A. Kepert, I J. Tehnas, M A. Pudovsk

BHP Billiton (BHPB) was the first company to start iron ore mining in the Pilbara at Mt Goldsworthy in 1966 through Goldsworthy Mining Limited (GML - then Consolidated Goldfields Australia, Cyprus Mines and Utah). Operations later started at Newman on Mt Whaleback in 1969 with the Mt Newman Mining Joint Venture (MNM û then comprising American Metals Climax û AMAX, Colonial Sugar Refineries û CSR and BHP). In 1986 it acquired majority ownership of MNM, and at the same time the previously 100 per cent BHPB owned but undeveloped Yandi property came on board. Purchase of Jimblebar (formerly McCameyÆs Monster) occurred in 1990 and full ownership of Goldsworthy followed in 1991. With the exception of Jimblebar (100 per cent owned), all mines are now 85 per cent BHPB and the balance with Itochu and Mitsui. This evolution of the company resulted in an eclectic mix of mines/ores, each with their varied exploration and evaluation histories. Discussion of some aspects of these histories, and reflections on changes in exploration-related activities with particular reference to discussion of advances in geological understanding since the 1960s forms the basis of this paper. BHPB presently has open cut mines at four main centres û Newman, Jimblebar, Marillana Creek (Yandi) and Yarrie û and is currently developing the former GML Area C near Yandi. With the exception of NewmanÆs Mt Whaleback mine and immediate satellites, all are contract operated. Ore is carried on BHPB railroads (696 km total) for export through the companyÆs Nelson Point or Finucane Island shipping facilities at Port Hedland. Some is directed to the BHPB Boodarie Iron hot briquetted iron plant near Finucane Island. Over 73 Mt of ore was produced by BHPB in calendar 2001, and the company has now mined over 1500 Mt in Western Australia since their operations at Yampi Sound first started in 1956.

Jan 1, 2002

By William C. McLaughlin

In the deep vein mines of the Coeur d'Alene mining district, rock bursts are a potential hazard to the mine structure and underground personnel. Damage repair costs are estimated by one company to exceed $1 per ton of ore mined. The Bureau of Mines, in cooperation with the mining companies, has conducted research intermittently over the past 10 years to help reduce bursts. Onsite inspections of major rock bursts were conducted, and reports were submitted to mine management; these included the geology and geometry of the affected area. The paper discusses the development and improvement of microseismic and surface monitoring equipment. The underground microseismic network, when operated on a regular basis and the results plotted daily, is capable of detecting stress concentration in certain areas. The surface seismographs record rock bursts, blasts, earthquakes, etc., throughout the district and show approximate location, time, and relative intensity of the event.

Jan 1, 1976

By Keith L. Harris

The economy continued to expand during the second quarter, but at a much slower pace than expected. According to latest estimates released by the Department of Commerce, the real gross national product (GNP) grew at a seasonally adjusted annual rate of 0.6% compared with a revised growth rate of 3.8%2 for the first quarter of 1986 and 2.3% for the second quarter of 1985 (table 1). The strong growth of personal consumption expenditures, Government purchases of goods and services, and residential investment was moderated by the growing trade deficit, declining investment in business inventories, and the continuing lag in nonresidential investment. Much of the decreased capital spending for the nonresidential sector for the first and second quarters resulted from reduced petroleum exploration and drilling in response to low petroleum prices. Capital spending and trade continue to be areas of weakness for the economy. Real new plant and equipment expenditures for 1986 are estimated to be 1.3% below those of 1985 (table 2). Real net exports of goods and services decreased $24.6 billion, as exports declined 5.6% and imports grew 16.5%. About two-thirds of the $19.3 billion increase in imports was in petroleum and petroleum products, which, because of their lower prices, should help the economy in the future. In response to the sluggishness of the economy, the Federal Reserve System reduced its discount rate from 6.5% to 6% in early July. Inflation, as measured by the fixed-weighted GNP price index, declined from a revised 2.5% in the first quarter to 1.9% in the second quarter because of significantly lower energy prices.

Jan 1, 1986

By Mitchell L. Spencer, Viswanathan Panchanathan

"Bonded magnets are important category in permanent magnets. They are made by one of the following processes: compression bonding, injection molding, extrusion, calendering. An overview of the various bonded magnet processes and properties of products made with different magnet materials along with their applications are discussed. The main emphasis will be on the use of bonded NdFeB and ferrite magnets.IntroductionBonded magnets are a major growth area in permanent magnets. Bonded magnets are made by any one of the following processes: Compression bonding; Injection Molding; Extrusion and Calendering [1,2]. Compression and injection molded magnets are rigid magnets. Materials used in calendering process produce flexible magnets. Only the extrusion process makes both rigid and flexible magnets. The binders used for the bonded magnets vary depending on the processes. Thermoset, thermo-plastic and elastomeric binders are respectively used in compression, injection and the calendering process. Extrusion molding uses elastomers or thermo-plastic materials. The most co=on magnetic materials, Ferrite, SmCo, Alnico and NdFeB can be used in any of the above processes either alone or in combination as hybrid magnets. Another material that has been developed for co=ercial application is SmFeN. Making the material has been challenging and it is being used in niche market applications in limited quantitiesIn the extrusion process, a highly loaded compound is used to produce strip or sheet and is continuously extruded through a die. In calendering the granulated compound is rolled to produce a continuous wide sheet. In the compression bonding process a uniaxial pressing force is used. These magnets have higher loading compared to injection molded magnets. In injection molding the material is forced into a mold cavity and has lower loading compared to compression molded magnets [2,3]. Most of the flexible magnets are made using extrusion and calendering processes and the most co=on magnet material is inexpensive ferrite. Flexible magnets have been made using rare earth materials, but on a very limited basis.The major advantages of magnets processed by extrusion and calendering are as follows: inexpensive tooling, automation; practically any 2D geometry; fast production rates; no chipping or breaking; a wide range of properties; on-line magnetization; easy to convert (e.g. cut, punch or shape).Compression bonded magnets are inexpensive to manufacture. They have higher magnetic properties compared to injection molded magnets; however lower than their sintered counterparts. The magnet shape is restricted to simple geometries and they require careful handling. Their isotropic nature allows complex magnetizing patterns."

Jan 1, 2013

By Jan Zwarcendyk

This study is primarily directed toward providing an understanding of the economic complexities associated with subsidence damage on the surface resulting from underground mining. Some of the pertinent theories on the physical stresses involved are reviewed, and both remedial measures and relevant laws in various countries are discussed. Part I (Chapters 1-3) is an historical overview of various aspects of subsidence problems (theoretical, remedial, and legal) during pre-World War I, between World Wars, and post-World War II, respectively. Part II (Chapters 4-9) presents a comprehensive analysis of the economic aspects of subsidence in relation to the following mining alternatives: (a) carrying out the lowest cost mining method without regard for any surface subsidence, (b) special mining techniques, (c) partial mining, (d) full recovery with stowing, and (e) sterilization or leaving the mineral unmined beneath selected areas. These alternatives are evaluated in terms of their measurable expenses.

Jan 1, 1971

By O. A. Carson

Introduction Although the equilibrium conditions of the copper-tin alloys have been the subject of a ?great amount of research, the equilibrium diagram is still in doubt. The first systematic investigation of the series was made in 1894 by Le Chatelier, who published a freezing-point curve. In 1895, Roberts-Austen and Stansfield published the complete liquidus and partial solidus curves, which they modified somewhat in 1897. Their liquidus as given in 1897 is essentially that accepted today (Figure 3). Haycock and Neville also published a liquid us curve in 1897. In 1898, William Campbell published a series of micrographs showing the changes in microstructure which accompanied the thermal changes of Stansfield? s diagram. The classic work on the bronze series was published by Heycock and Neville in 1903. Their diagram was based on both thermal and microscopic evidence, and is the first for this series of alloys which can be considered nearly complete. Further, it was the first bronze diagram in which any attempt was made to apply the phase rule in the interpretation of the thermal and microscopic results. That portion of Heycock and Neville's diagram covered by the present work is reproduced in Figure 7.

Jan 1, 1929

By Don Reining

The sand and gravel industry in Southern California has made a sizeable contribution to the construction development of the 15 County area in this part of the State. Facing this mineral extraction industry, in the next decade, is a problem of meeting the market demand. The question is, "how can sand, gravel and rock operations be made compatible with goals for sound and attractive community development?" Three basic principal characteristics of the land needed for this-mining industry are: 1. The land must have workable sand, gravel or stone deposits. 2. The land must be properly located for transportation purposes close to the market in order to sell the aggregate at a minimum cost. 3. The land must be zoned so that it will be permissible to mine.

Jan 1, 1967

By S Withell, K Sheehan

Whitehaven Coal (WHC) is undergoing a transformative journey, deeply committed to the principles of a High Reliability Organisation (HRO) and the establishment of a mature, interdependent culture founded on psychological safety. This ongoing commitment is not merely aspirational but is supported by performance improvements backed by both quantitative performance data and qualitative evidence of cultural progression. WHC has strategically integrated leading and lagging indicators to target fatal risk. WHC focus areas include an emphasis on strategy and risk appetite, targeted data, informed learning, proactive addressing of fatal risk and the integration of data management and technology.

Apr 16, 2024