Search Documents

By J. Coxon, G. W. Walker

The paper describes the discovery, location and events concerning three types of heating which have occurred in recent years: a) in a district being salvaged, b) in the shaft pillar at an air-crossing, and c) in the gate side of a production district, all of which have occurred in the Beeston Seam at collieries in the deeper eastern part of the area. The paper describes the precautions, air sampling arrangements, training methods and codes of practice which have been adopted at collieries where spontaneous combustion is, or is likely to be, a hazard. The air samples taken from behind the stoppings following the sealing off of the salvaging district are examined and interpreted. The problem of effectively sealing off where more than two stoppings are required is made apparent. Other lessons have been learned as a result of these heatings and are described in the paper.

May 23, 1905

By Ronald Erdmann

Today the BOF filter dusts and sludges are mainly dumped due to their zinc contents. By typically ranging from 2 to 5 % they prevent the filter dusts and sludges from beeing recycled via the blast furnace route. Based on the different discharge kinetics of Iron and zinc during the main blowing period In a bottom stirred BOF a simple and efficient system for recovery allow zinc fractions has been developed. The obtained material Is suitable for recycling without nsc of shell formation In the blast furnace. Different subsequent development steps have been performed. By starling with a very simple lime dependent model the sludge from the BOF off gas cleaning system was collected in two different sludge channel systems. This model based an the fact that most of the scrap based zinc Is discharged from the melt within the first eight to ten minutes of the BOF process. To Improve the system a spectroscope zinc sensor was Installed at the hot section of the off gas cleaning system to get more reliable informations on the actual zinc concentation of the BOF dust. By use of the system up to 50 % of the BOF sludge can be recycled.

Jan 1, 1995

By Arnold M. Lansche

[Selenium and tellurium are rare elements in the earth's crust. Their scarcity and primary dependence of supply on copper and lead output are in consonance with the relatively small quantities consumed at 1964 level. Production depending on output of copper and lead creates a supply situation- which would appear to militate against development of large-scale usage of these elements. However, supplies have adequately met. demand in the past decade and can be increased substantially if warranted by new uses for either selenium or tellurium Ores of copper and lead re the principal sources of selenium and tellurium. Byproducts from the smelting and refining of copper and lead concentrates are incorporated in refinery anode slimes from which selenium and tellurium metal are recovered.]

Jan 1, 1967

By G. J. Abbaschian, A. B. Gokhale, M. M. Kunjapur

"A laboratory scale model furnace was constructed for obtaining radially inward oriented columnar grains in disc shaped castings. The furnace consisted of eleven circular, concentric, equispaced resistance heaters on each half of a split graphite mold. Water or air flowing through a copper pipe along the periphery of the disc constituted the heat sink. After filling the mold, the heaters were turned off consecutively in top and bottom pairs from the rim towards the center, causing the temperature gradients to move inward. Equiaxed structure was obtained at the center by turning off the inner coils together when desired. Sn:15%Pb alloy was used to cast integral blade disc castings using the above technique to obtain dual-property discs with a central equiaxed structure and an outer columnar grain structure projecting inwards from the blades to the rim. A numerical technique was used to predict the temperature profile in the disc during solidification, and good correlation was obtained with the experimentally measured temperature profiles. The corresponding heat transfer coefficient values obtained were h = 544 Wm- 2k-1 (0.013 cal/cm2- ° C-sec) for cooling between metal and chill and h' = 71 Wm- 2k-1 (0.0017 cal/cm2- ° C-sec) for the heat input from the hot mold to the liquid metal. BackgroundHigh temperature alloys used in the current generation of gas turbine engines have evolved through two main stages of development: in 1950's, the increase in the efficiency of gas turbines was paced by improvements in alloy design, which led to the development of Ni and Co-based superalloys (1). By mid-1960's, it was realized that improved alloy chemistry alone was inadequate in meeting the increasingly stringent service requirements. The focus of research then shifted from alloy development to process development, and resulted in the introduction of directional solidification (DS) techniques for the production of turbine blades and vanes (1,2).Under typical operating conditions, the blades and vanes are subjected to aerodynamic loading, while the blades are additionally subjected to high centrifugal loading and vibratory stresses. The primary material requirements for blades may be summarized as follows (1,3):•,High creep resistance•,Good high temperature tensile strength (typically in the range of•,275 to 550 MPa at temperatures in excess of 750°C)•,Resistance to both low cycle and high cycle fatigue (LCF and HCF)•,Resistance to erosion, corrosion, and oxidation•,Resistance to thermal fatigue"

Jan 1, 1986

By M. P. Neira

In-situ leaching of copper from chalcocite relies on ferric iron concentration in the lixiviant being reduced to ferrous. To re-establish the ferric concentration in solution, ferrous must be re-oxidized. This reaction is slow under normal chemical conditions but it is catalyzed by Thiobacillus ferrooxidans bacteria. BHP Copper's Miami In-situ unit developed a bio-reactor as a method of oxidizing ferrous to ferric. The effects on oxidation of temperature, CO2? oxygen, and air injection flowrate were defined. This paper summarizes the results of ferrous bio-oxidation using plastic column packing and oxide ores as bio-reactors and the leaching results of the bio-reacted lixiviant on chalcocite ores.

Jan 1, 1997

By E. H. Mulligan

THE ERRINGTON B-I mine is located on the Errington orebody of Steep Rock Iron Mines, Limited, at Steep Rock Lake, Ontario. In 1946, this orebody entered the shipping lists of the Lake Superior iron ranges as an open-pit operation. During the period 1946 through 1953, the mine produced a total of 9,000,000 tons of iron ?ore. In 1950, as the mine approached the economic limits for open-pit operations, ground was broken for an underground development to exploit the deposit at depth. The mine is designed for an ultimate production of 1,500,000 tons per year by the block-caving system of mining. The initial shaft is 1,200 feet deep and will produce or-e from the 700 and the 900 levels. The 1,100 level will be used as a drainage level and as a haulageway for waste rock, which is hoisted to surface by skip. Ore from the two production levels moves by a system of ?ore passes to a crushing plant located below the 900 horizon and is hoisted from this point to surface by conveyor belt. At the present time, all material handling on the levels is by tramming, but as tram distances increase conveyor haulage will probably be installed. The initial stage of the Errington B-1 development is expected to produce 6,000,000 tons of ore over a period of four years. The second stage will require deepening of the shaft and development of lowe1? production levels. The conveyor hoisting plant will be extended to serve these new levels. We visualize the mining of this orebcdy down to 2,500 feet by these methods.

Jan 1, 1956

By Erik Sundström, Magnus Nygren

Having seen significant improvements to accident rates in the last 40 years, companies in the Swedish mining industry now show a greater focus on the development of safety cultures throughout their organisations and workplaces. However, there is a lack of research examining the different safety initiatives and strategies practiced in the industry today. This study explores the potential influence and consequences such initiatives may have on the development of safety cultures in the Swedish mining industry. Twelve interviews with experts on safety initiatives from four different Swedish mining organisations were conducted and analysed in a process based on qualitative thematic analysis to identify notable connections to safety culture development. The results of these interviews highlight proclivities in the implementation and use of safety initiatives such as subjects of focus, methods and desired effects. This enables the interpretation of the conceptualisation and methods for the development of safety culture in these organisations based on their approaches to safety development. We believe the results of this study can serve as support for discussions on safety culture development in the Swedish mining industry, and be of interest for international mining industries, in addition to approaches to research in this field. However, we also believe it is important to emphasise the opportunities to approach safety culture in mining from different perspectives than those common today.

Jul 19, 2023

By Yun Li

In 1999 Yunnan Copper Corporation (YCC) decided to modernise their copper smelter and change the existing sinter plant I electric furnace process to a combination of ISASMEL T and electric slag cleaning furnace. The main aim of the project was to improve the environmental performance and decrease the energy consumption. Generally the project has been successful, partly attributable to the selection of a reliable and fully demonstrated technology. The design capacity for the ISASMELT furnace is 600,000 tonnes of dry copper concentrate per year. The furnace has been running smoothly since heat up in May 2002. YCC expended considerable effort in the preparation for plant operation. An extensive training program for key YCC personnel at the Mount Isa Copper Smelter improved their understanding of the process significantly and ensured successful hand-over of the technology. This paper describes the project history and summarizes initial operating results.

Jan 1, 2003

By Harold M. Smith

The data in this report were prepared to show how Bureau of Mines routine crude oil analyses could be used to evaluate crude oils in terms of common commercial products . The use of Bureau of Mines routine analyses to determine hydrocarbon - type relationships for the gasoline and gas - oil fractions is demonstrated . For this purpose the correlation index , the aromatic profile and the naphthene profile are used to establish reasonably acceptable values for hydrocarbontype relationships . The derivation and meaning of these indications are discussed . These analytical interpretations are applied to a group of high - sulfur crude oils from the Near East , the Permian basin of West Texas , Venezuela , Colombia , California , and other locations , and the resultant data for gasoline , gas oils , lubricating oils , and asphalt are compared by appropriate tables and graphs . Because the Near East crude oils contain higher quantities of paraffins in the gasoline and gas oil ranges , they will yield good , lowsolvency solvents and good kerosine , jet fuel , and diesel fuels , but straightrun gasoline of inferior quality compared to similar products from either West Texas or Venezuelan high - sulfur oils . The Near East oils also should be good sources of lubricating stock . However , when used as stock for catalytic cracking or reforming , the Near East oils suffer by comparison because they are deficient in naphthenes .

Jan 1, 1964

By Ryan Marsters, Adam Pring

The Rawah Ditch is a mountainous water supply diversion which supplies Larimer County, Colorado with water since 1903. The ditch includes two historic tunnels excavated by drill and blast through a gneissic rock buttress. Both rock tunnels were failing with annual convergence. After a snowshoe-accessed eld investigation, nite element modeling, and an alternatives analysis, a diameter DE pipe was inserted within each tunnel and the annulus lled. The proect was implemented in an Alternative Delivery contract lasting ve months from eld investigation through procurement and construction.

Jun 23, 2024

By Frank E. Williams

This Bureau of Mines report deals with the urbanization of Tucson, Ariz., a southwestern city with an arid environment. Zoning regulations concerning known aggregate sources are described, and information relating to projected needs for the urban area is furnished. History of growth is outlined not only for the local aggregate industry, but also for the entire urban area. Past conditions are pointed out and background material for future conditions is provided.

Jan 1, 1967

A working understanding of present coal mine communications equipment and its usage is an essential prerequisite to the determination of future communications systems needs. As a means of gaining this understanding, a field survey program was planned and implemented. The plan formulated called for obtaining both qualitative and quantitative data from three main areas of interest: the types, physical condition, and performance characteristics of equipment presently used in the sample of mines to be visited; the relationship present communications has to safety and productivity; and the practical, future communications needs as derived through interviews with present mine management. In compliance with the original plan, the type and physical condition of equipment in use was found through at-mine interviews of personnel responsible for installation and maintenance. Further evaluation was made through the review of equipment instruction books and maintenance manuals and through in-mine inspection of communications equipment and signal distribution networks. The performance characteristics were determined through listening to conversations and noise levels and by talk-testing from randomly selected stations throughout each mine. System operation was evaluated by asking communication system users their opinions and by noting any difficulties personnel had using the systems.

Jan 1, 1974

By Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Underground mining environments bring occupational health and safety issues with some severe dangers such as mine disasters like explosions. During such events, miners might escape using main access openings, or find a safe haven like refuge alternatives (RAs) to wait and be rescued and evacuated to the surface. In this paper, RAs are explained with their early and current applications. A classification as permanent and portable is explained depending on the conditions and their abilities. This classification is followed by the utilization and survivability of RAs with the requirements and recommendations of the main mining countries. Based on the utilization and survivability constraints, basic human requirements, waiting for a rescue team, and the required physical specifications of RAs during the events are analyzed in detail for various countries with their regulations. Among these, the specification, resistance to the explosion, is discussed in particular, and the studies in the literature are examined in terms of structural deformation. The highest deformed zones, the beneficiation of reinforcing steel components such as stiffeners, and the simulation approaches are investigated through this review.

Sep 24, 2022

By J. B. Kitchin

"The design of conveyor belting for use in mines poses problems to the manufacturer that are unique. The challenge to be met is that of the production of a conveyor belt which can withstand use and misuse in an environment that may differ vastly from one country to another, and even between one mine and its neighbour.The development of a product to meet such varying requirements necessitates a protracted program of trials, both in the laboratory and in the field; a new successful development, the only criterion, can be said to have been achieved only after very long-term usage under actual, deliberately chosen, arduous mining conditions.New developments in conveyor belt construction can never stop, no more than can developments in new and advanced mining techniques. A new problem is set-an answer must be found. Some of the problems are noted here, and answered where possible, in what must after all be little more than an excursion into a very comprehensive and detailed subject."

Jan 1, 1967

By In-Ho Chi

In copper metallization, resistivity of copper seed layer is very important since the thickness of seed layer is less than 200iun. Conventionally MOCVD has been used for this purpose however electroless copper plating is simple process and the resistivity of copper deposit is less than that of copper prepared by MOCVD. In this study eIectroless depositions of copper were conducted on different substrate to find optimum conditions of electroless copper plating for electronic applications. To find optimum conditions, the effects and selectivity of activation method on several substrates were investigated. The effects of copper bath composition on morphology were investigated. The effects of pH and stabilizer on deposition rate was investigated. The resistivity of copper with thickness was also measured.

Jan 1, 2001

By Victor Himel

This report documents a systematic approach towards implementing an improved ensemble for the mine rescue team system that will protect against the hazards of mine rescue and recovery and will also afford improved performance through increased comfort and maneuverability, lighter burdens, and improved human engineering designs. In the first part (Task 1) the mine rescue team's protective needs were defined along with the test methods required to evaluate whether a particular piece of gear met these needs. Task 2 assessed existing gear against performance criteria and standards developed in Task 1. Task 3 consisted of the conceptual design and construction phases of the MRPE program. Special consideration was given to advanced concepts, materials, and equipment.

Jan 1, 1982

By H. M. Smith

MORE than a year before the United States entered World War II, the requirements of the National Defense Program indicated the need for additional sources of aviation gasoline. On September 10, 1940, Dr. R. E. Wilson, Group Executive, Advisory Commission of the Council for National Defense, requested the Bureau of Mines to undertake a survey of crude oils of the United States to designate those suitable for the production of 91-octane aviation gasoline. As quickly as a program could be defined, agreed upon, and funds provided to conduct the work, the Bureau began the project. Over a period of many years the Bureau had collected samples and made analyses of thousands of crude oils produced in the United States. Although these analyses did not include octane numbers of the gasoline fraction, they provided data necessary for calculating the correlation index. This index, developed within the Bureau, is a measure of the types of hydrocarbons present in gasoline and therefore is roughly indicative of the octane value. This fund of information from Bureau of Mines Hempel analyses, supplemented by information obtained from oil companies, reduced considerably the necessary laboratory work by providing data that permitted a large number of crude oils to be eliminated from consideration. However, in the survey carried out during the last part of 1940 and the first half of 1941, 225 samples of crude oil were collected and distilled. Octane values of the distillates were determined by the Army AFD-1C method. (See page 57.) A report containing these results, together with the calculated amounts of 91-octane aviation gasoline available from these sources, was prepared and distributed to the several offices of the Office of the Petroleum Coordinator for National Defense in August 1941. In December 1942 the Office of the Petroleum Coordinator for National Defense became the Petroleum Administration for War (P. A. W.).

Jan 1, 1951

By G. Drennan, A. Cameron

"South African mining operations depend on the skilled professionals produced through the tertiary education sector. In geoscience courses at the University of the Witwatersrand, which lead into the mining sector, there has been a significant increase in student intake over the past 15 years. This increase has been characterized by a radical shift in demography: in classes where white male students once formed the majority, black female students are now in the majority. This demographic shift appears closely linked to policies addressing issues of social justice and transformation in post-apartheid South Africa. We document this change and consider the role played by employment equity legislation (as in the Mining Charter) and corporate social investment strategies in the mining industry, notably through bursaries offered to black female students. We also look at the changing needs of the industry, where the critical need for managerial skills, not just technical knowledge, is highlighted through data from surveys of past students and industry managers. Our findings indicate the need for a curriculum adjustment to meet these changing requirements, as well as more rigorous selection criteria for bursars than simply gender, race, and appropriate matric results. IntroductionThe South African economy has historically been linked to mining and the exploitation of mineral resources. South African mining operations are dependent on the professional labour that is produced through the tertiary education sector, with critical thinking, teamwork, and the art of negotiation having been identified as the crucial skills required for this industry (Sideropoulos, 2014). Over the past three decades the South African system of education has gone through a period of dysfunction that it is struggling to rectify (Maphai, 2014). This has impacted on the levels of academic preparedness of students applying for places in higher education. Concurrently, government and university policies have widened access to higher education in response to the need to address issues of social injustice and transformation related to South Africa’s history of apartheid. As a result, the number of students admitted to universities has increased dramatically. In the School of Geosciences at the University of the Witwatersrand (Wits), the increase in student numbers has been accompanied by a significant change in demographics: classrooms which in the past were dominated by white males have given way to classrooms in which black females are often in the majority. This demographic shift is related to legislation such as the Mineral and Petroleum Resources Development Act and the Broadbased Socio-Economic Empowerment Charter, developed to reshape the socio-economic and equity frameworks of the country (Botha and Cronje, 2015). Requirements aimed at transformation in terms of management, skills development, and employment equity, together with corporate social investment (CSI) requirements, have resulted in bursaries being made available to attract students from designated groups, which in turn has increased the number of black students, and notably black female students, taking courses in geosciences. However, due to the economic downturn, instability in the mining industry has recently resulted in the downsizing of some mines, with international investors pulling out of South Africa. This instability resulted in devastating strikes across all sectors of the mining industry (Stewart, 2013) and in Marikana, an important platinum mining area, the strike culminated in a deadly shoot-out between miners and police. The resulting tensions spilled over into the gold mining sector, resulting in further strike action, shaft closures, and retrenchments. These challenges have implications not only for the mining industry in South Africa, but for the tertiary education providers whose graduates would have been absorbed into the mine-related workforce."

Jan 1, 2017

By Gillies A. D S

Rail, port and shipping charges represent 30 to 50 per cent of landed costs for Australian coal mines selling to Asia. This proportion is higher for sales to Europe, yet it is in Europe where Australian producers are aiming for increased market share. The landed cost of coal to the international customer is the key parameter which determines market competitiveness. The objective of this study is to examine Australian export coal competitiveness in terms of transport distance. The approach used examines world coking coal and steaming coal production and the transport distances between major exporting regions and importing countries. Reference is made to the importance of land transport costs and a comparative approach for emphasising the relative magnitude of this factor is developed. Models developed are examined in terms of Australia's exports and a conclusion is reached that a reduction in rail freight costs would be an effective measure for improving the competitiveness of Australia's coal industry.

Jan 1, 1994

By Ragnhild E. Aune, Shahid Akhtar, Reza Beheshti

"The potential use of Black Dross (BD) as a raw material for the production of refractories, fluxing agents and glasses is the main motivation of the present study. Heat treatment experiments were carried out in Ar, and under reduced pressure (20 Pa), to evaluate the salt removal efficiency. The chemical composition of the BD after heat treatment was investigated by SEM-EDS and XRD analyses. Based on the present results, it is established that the salt starts to evaporate at ˜1273 K in Ar, and under reduced pressure. The salt removal efficiency in a 20 g sample was found to increase in both cases as a function of time and temperature. Moreover, in Ar the chlorine concentration was lowered to 0.3 wt% after heat treatment at 1523 K for 10 hours. Under reduced pressure, however, 0.2 wt% residual chlorine was obtained after 8 hours at 1473 K.IntroductionIt is believed that aluminum recycling in the near future will become the main route of aluminum production [1]. Black dross (BD) that is produced during this process contains, among other things, high amount of salts like NaCl and KCl [2, 3]. Almost 800,000 tons of BD is annually land filled in United States and this number continues to grow with the increase in aluminum recycling [2]. The BD should be dumped in controlled land field and it is costly procedure [4, 5].The water-soluble compounds in BD react with water or environmental humidity and release chlorides into the water and/or generate toxic gases such as H2, CH4, NH3 and H2 S [6-8]. In the Europe, BD is considered as toxic waste and its disposal as landfill is forbidden [8, 9]. After salt removal, the BD is considered to be non-hazardous and can be buried under ground [10].On the other hand, BD do also contains many relatively valuable compounds that may be changed in to useful materials as a result of further treatment [11, 12]"

Jan 1, 2012