Search Documents

By J. T. Dunham

Zirconium has possible use in industry where severe corrosion conditions are encountered because it resists attack from a variety of corrosive environments. However, very little experimental testing has been done to evaluate the corrosion behavior of zirconium when simultaneously subjected to high tensile stresses and exposed to corrosive environments. This investigation was initiated for an evaluation test, but was limited to environments consisting of ferric chloride solutions which were known to attack zirconium and were shown to promote stress-corrosion cracking in preliminary tests. Tests for cracking susceptibility were conducted by the Bureau of Mines to show the effect of stress, solution concentration, air aeration of solution, and the method of mechanical processing. Tensile stress was applied to the specimens by a constant-load method which proved more reliable than a constant-strain method.

Jan 1, 1961

By Richard E. Otoo, Evan J. Owen, Virginia T. McLemore

According to the U.S. Geological Survey (USGS), a critical mineral is one that is essential to the economic well -being of a nation and whose supply may be disrupted due to geological, geopolitical or environmental factors (Nassar et al., 2020). For example, REEs are critical to the production of electricvehicle motors as well as wind turbines, yet China’s share of their global production rose to more than 95 percent in 2010 (IEA, 2021). China’s share has since declined, with production quotas dropping to nearly 70 percent by 2023 (Statista, 2023). This and similar situations with many of the critical minerals raise deep global concerns about supply-chain vulnerabilities (Bauer et al., 2011). Critical minerals are used in the production of renewable energy, electronics, agricultural products and common household items (McLemore, 2020). As the global demand for these minerals continues to grow, it is not sufficient to rely solely on scaling up production from existing operations. While increasing production from known deposits can provide short-term relief, long-term resource security requires discovering new, economically viable mineral resources. One of the most effective ways to secure future supply is through mineral exploration, which increases the global inventory of critical minerals and also minimizes risks posed by market monopolies and political instability. The major challenge of mineral exploration lies not only in identifying mineralized deposits but also in determining whether discovered concentrations are sufficient to warrant further investigation and development. A fundamental concept in this decision-making process is using cut-off grade. In this article, cut-off grade refers to the minimum concentration of minerals required to justify further exploration efforts based on factors such as type and size of mineral deposit, mining and processing technologies, associated byproducts/coproducts and the market price of these minerals. Typically, economic cut-off grades are used to determine whether a mineral deposit can be mined profitably. However, this article focuses on preliminary cut-off grades needed to establish whether the amounts of critical minerals within a deposit are high enough to justify further exploration and detailed evaluations. By comparing mineral deposit grades, size, production and extraction technology, and other economic factors with established and active mines, exploration teams can estimate cut-off grades that justify further exploration.

Aug 1, 2025

By G. E. Veins

This paper summarizes an investigation in which beneficiated ilmenite ore was smelted in a continuous, three-phase, 250 kv.a., open-top electric furnace. Minus %. inch ore was smelted, using the standard method. Fine ore, in the order of minus 14 mesh, was smelted in the briquetted form by the open bath method, and in the unagglomerated form by the cold dry-top method. The latter was shown to be superior. The data obtained .are discussed at some length. During the investigation, slag aver-aging 82.5 per cent Ti02 was produced over a period of 87 hours, the maximum being 85 per cent. Such slag should .be particularly attractive for the production of titanium tetrachloride, from which titaniurn metal is produced. The advantages of using paper-mill bark for producing a furnace charge of low bulk density, as required in cold dry-top smelting, were emphasized.

Jan 1, 1957

By E. F. Loiseau

(Read at the Philadelphia Meeting, February, 1878.) UNTIL June, 1868, it had not been attempted, either in this country or abroad, to manufacture by mechanical means, from anthracite coal-dust, artificial fuel for domestic use. Several attempts had been made to utilize coal-waste by converting it into a fuel for manufacturing purposes, but none of the processes were original, and they were merely applications of the well-known European processes and machinery, slightly modified by American ingenuity and mechanical skill. With one exception all those attempts have been failures. The great difficulty in the application of European processes and machinery has always been the limited production, and the excessive cost of the manufactured product, as compared with the cost of mining and preparing the ordinary anthracite coal for the market. The only serious and intelligent attempt to manufacture, on a large scale, artificial fuel for manufacturing purposes, has been made by the Anthracite Fuel Company, whose works are erected at Fort Ewen, near Rondout, New York. This company, organized under the auspices of the Delaware and Hudson Canal Company, had to go through the usual course of difficulties, breakages, and disappointments, which seems to be the lot of every new industry. Thanks, however, to the energy and perseverance of Mr. L. L. Crounsse, a gentleman of means, from Washington, D. C., the enterprise succeeded, and it is to-day established on a permanent basis. In order to increase the production, and to reduce its cost, the Anthracite Fuel Company was compelled to change most of its plant, and to erect more powerful machinery, producing lumps of a larger size, almost twice the size of the lumps made previously by the same company. This increase in the size of the lumps has been resorted to in Europe as well as in this country, in order to increase

Jan 1, 1878

By C W. Davis

Every diesel engine emits approximately 100 million nano diesel particles (nDP) per cubic centimetre of raw exhaust. Each nDP has a diameter of between 50 and 70 nano metres or 1/100th the size of red blood cells (diameter of between 6 and 8 microns). When inhaled, some nDP pass through the lungs and penetrate all body tissue [1]. Europe and North America have recognised and are addressing the long term health problems posed by nano diesel particulate matter (nDPM) across their societies [2.3]. Australia has been slow to recognise the issue, at both a societal and mining industry level. There are chronic health effects for every underground miner and serious legal issues for mining companies with increasingly stringent Occupational Health and Safety legislation being implemented at a state level across Australia. This paper will review progress within Australian society and more particularly the underground hard rock mining industry, particularly in Western Australia (WA).

Mar 15, 2021

By Gang Qi

The solubility of nitrogen in pure molybdenum was measured over the temperature range 2173 to 2473 K and up to one atmosphere (101 kPa) of nitrogen gas pressure. Both thermochemical and kinetic aspects of this phenomenon were considered in this study. The solution of nitrogen in molybdenum may be expressed by the reaction 1/2N2(g) = {N} (Mo,s), for which the standard Gibbs energy is given by the expression {A}G° = 78,500 + 27.36T Joules/g atom N. The formation of molybdenum nitrides, specifically Mo2N, was considered. Attention was also focused on the mechanism of nitrogen solution in molybdenum. Estimates of the diffusivity of nitrogen atoms in solid molybdenum were derived from the kinetic data.

Jan 1, 1991

By J. L. Heaver

All complete plant foods require phosphorus, nitrogen and potassium. And phosphate rock is the primary source for the phosphorus of the inorganic fertilizers. As more and more world food production is grown with these chemical fertilizers and since the Florida field supplies over 30% of the phosphorus component, let us look at the vital phosphate industry. Mining of phosphate rock in Central Florida began in 1891 and production has continued to grow at a steady pace. In 1965 a phosphate mine was opened in Hamilton County, North Florida and one in Beaufort County, North Carolina in 1966 . Since the beginning of mining in 1891, approximately 700 million metric tons of phosphate rock have been produced of this amount one-half was mined in the last 11 years. While the field was not deliberately "high-graded," the best of the known deposits were mined first. Those now being mined, and those yet to be mined, cost more to operate and the product is of lower grade. The U. S. Bureau of Mines' data for 1977 lists "Florida" phosphate rock production as 40.6 million tons; 86% of U. S. production and 85% of "Florida" capacity. The U. S. Bureau of Mines includes North Carolina production in "Florida" statistics so as not to reveal individual data for the one mine operating there. Approximately one-half of "Florida" production is exported, either as rock or as rock equivalent in upgraded products. Deposits of phosphate rock necessary to support present and future production are catalogued as: reserves, paramarginal reserves and resources. Reserves denote deposits which can be mined at a profit now. Paramarginal reserves are defined by the U. S. Bureau of Mines and the U. S. Geological Survey as: that portion of sub-economic resources that a) borders on being capable of production economically, or b) is not commercially available solely because of legal or political circumstances. The " b)" part of this definition may now be expanded to include environmental controls and requirements. Resources are deposits which cannot be mined at a profit at present. Listed in Table I are reasonable values for each of the three categories of phosphate deposits in the northern and southern parts of Central Florida. North Florida and North Carolina.

Jan 1, 1978

By Frances H. Clark

IN a concern with the varied interests of the Western Union Telegraph Co., where practically all types of metals, both ferrous and nonferrous, are utilized, many types of failures of materials occur. These have to do not only with outside plant construction, such as corrosion and fatigue of line wire and cable, but also with inside plant equipment operating at such high speeds that rapid deterioration of metal. parts due to fatigue and wear results. Both corrosion and fatigue affect the life of copper wire so its normal life in any particular locality is largely dependent on the atmospheric conditions. Tensions vary widely owing to changes in temperature and ice and wind loadings and the wire is Subject to a great range of vibration caused by wind gusts aril vibration front trains or other heavy vehicles transmitted through the earth. High frequency low-amplitude vibrations are sometimes audible as singing in the wire. The other extreme is the vertical slashing or dancing of the wire observed during severe storms where amplitudes of 9, ft. or more at low frequencies have been observed.

Jan 1, 1942

By Miguel Reyes, Bruce Whisner, Joseph Bickson, Lincan Yan, David Yantek, Justin Srednicki, Nicholas Damiano, Eric Bauer

Built-in-place (BIP) refuge alternatives (RAs) are designed to provide a secure space for miners who cannot escape during a mine emergency. Heat and humidity buildup within RAs may expose miners to physiological hazards such as heat stress. To minimize the risk of heat stress, Title 30 Code of Federal Regulations (CFR), or 30 CFR, mandates a maximum allowable apparent temperature (AT) for an occupied RA of 35 °C (95 °F). The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive research on the thermal environment of occupied RAs intended for use in underground coal mines. NIOSH research has demonstrated that a fully occupied BIP RA can exceed the AT limit by more than 5.6 °C (10 °F) in mines with elevated mine strata and air temperatures. In this circumstance, an RA cooling system could provide a solution. This paper provides an overview of test methodology and findings as well as guidance on improving the performance of a cryogenic air system prototype by optimizing the flow rate, increasing the tank storage capacity, and improving the efficiency of the heat exchanger of the cryogenic system. This may enable BIP RAs to meet the 35 °C (95 °F) AT limit in mines with elevated temperatures. The information in this paper is useful for RA manufacturers and mines that may choose to implement a cryogenic air system as a heat mitigation strategy.

By Paul M. Tyler

One of the best present-day yardsticks of the material welfare of a nation is its consumption of minerals, The United States, with only 7 percent of the world population, consumes 45 percent of the world wealth, pays the highest real wages, has the shortest working hours, and numbers the largest percentages of home owners among its population, and at the same time its per-capita consumption of minerals is far greater than that of any other nation. In 1937, British India, with roughly twice the population of the United States, used less than 2 percent as much lead, 4 percent as muck zinc, and 13 percent as much copper; even in Europe, which has three times our population and where war preparations have greatly expanded the normal needs of peaceful industries, the aggregate consumption of metals and industrial minerals other than lignite is less than the total for the United States alone. The march of civilization passed from the Stone Age to the Bronze Age before the dawn of history. It may be questioned whether man or monkey first threw stones at an enemy, but only man could have fashioned rough stones into weapons. Eoliths rudely shaped by apelike men are believed by archaeologists to have antedated by hundreds of thousands of years the existence of our own human ancestors. The primitive people that followed the retreating Ice Cap northward in early quaternary period - at least a million years ago - were fairly adept in the shaping of flints and even used a little copper. The Bronze Age, so-called, superseded the Stone Age when, around 8,000 B. C., the news spread that chunk s of natural copper could be pounded into better weapons or cutting implements than ever could be made by chipping stones. The Bronze Age gave place to the Iron Age about 1,000 B, C., and though students of modern history may speak of the Coal Age, the Petroleum Age, and the Automobile Age, and so on, these ages have all been crowded into a brief century and a half. The truth is that we still are in the Iron Age, unless perhaps we choose to call it the Age of Many Metals.

Jan 1, 1940

By Staff

"INTRODUCTION Sheet mica is one of the most important minerals in modern industry. It is used in many kinds of electrical devices, and up to the present time no satisfactory substitute for it has been developed. It is necessary for the successful operation of airplanes, ships, motor vehicles radios, and radar equipment. Early in World y r II, the Array and Navy, foreseeing the need for conserving the stock of sheet mica on hand and realizing that imports from India and Brazil were falling off, had strategic mica placed on the critical war-materials list.Examination and exploration by the Bureau of nines indicated that there probably are large undeveloped deposits of mica in Alabama, some of which are near the surface and others at greater depth. The quality of most of this mica is high.During World War I, Alabama mica producers added materially to domestic production, but after 1920 virtually all of the mines closed end miners scattered. During World War II, when imports from India, Madagascar,Brazil,,other foreign sources were reduced, sometime was required for Alabama to act into production. Operators began to produce small quantities in 1942.The Colonial Mica Corporation was created by the Government during 1942 to buy Mica for the Metals Reserve Company, end later Colonial was made sole buying accent for strategic mica. About this time the Bureau of Mines estab¬lished the graphite field laboratory at Ashland, Ala. Samples of mica wore submitted for examination, and advice was requested by property owners and mine operators. This continued during 1943, when as many as 400 visitors a month called at the Bureau's Ashland field laboratory."

Aug 1, 1946

By D Brown, Z Tabor

Projects must be flexible to account for the rapid development of new technologies and changing stakeholder expectations. Coupled with calls for bleeding-edge solutions, customers, shareholders, and regulators demand robust, safe products and systems-of-systems. Developing and integrating these solutions is becoming increasingly complex and maintaining the flexibility required to ‘pivot’ to effective solutions can be a serious challenge. The necessary flexibility is fundamental to the Agile ethos, and this family of methodologies therefore offers a potential solution to this challenge (Beedle et al, 2001). These have traditionally been delivered with systems engineering applied through a Waterfall methodology. Agile Systems Engineering combines both approaches and presents a means to achieve these goals without compromising flexibility, quality or safety. A robust methodology for the application of Agile Systems Engineering is required to enhance practical outcomes and reduce risk for real-world mining projects.

Sep 1, 2024

By David B. McWhorter

Conventional analyses of seepage through saturated media do not apply when tailings impoundments are located above a partially saturated zone. Three stages of seepage are identified and methods for estimating the seepage rates and duration of each stage, based upon flow in partially saturated and saturated porous media, are demonstrated. The effectiveness of earthen liners is discussed and procedures for estimating the required properties of the porous media are provided.

Jan 1, 1978

By ROLLIN THOMAS CHAMBERLIN

The studies herein reported were begun as a part of researches undertaken by the United States Geologü;al Survey looking to the more effcient utilization of the coal in the United States through the reduction of waste in its extnidion, and were continued as part of further researches having regard to the conservation of the fuel resources of this country and to the lessening of injuries and fatalities in coal mining. Among other phases of the general problem to be studied were the origin of the gas whidi escapes into coal mines, its modes of occurrence in the coal and rock strata, and the conditions governing its outflow into the mines. The subject of relative danger from destructive explosions due to gas and coal dust in different mines belonging to different coal fields was to be one of the principal lines of investigation. But this work was barely under way when the series of unusually disastrous explosions in the Naomi, .Monongah, and Darr mines of Pennsylvania and West Virginia, in December, 1907, afforded an exceptional occasion to observe the behavior of explosions on a large scale. Because of the opportunities for study afforded by these terrific explosions, the inquiry originally planned was d ¡verted to the more specific investigation of the conditions in tl10SC mines, and the examinations have been directed toward finding those qualities of gas and dust which were concerned in these explosions. The following discussion, therefore, consists essentially of a report on that subject; but it is far from being exhaustive, and is to be regarded as a preliminary outline of investigations which are still in progress. The first of the three mine explosions mentioned occurred in the Naomi mine of the United Coal Company, near Bellevernon, Pa., on Sunday, December 1, at 7.40 p. m. All the men who were within the mine at the time, fortunately only 34, were killed. Less than a week later there occurred in mines Nos. fì and 8 of the Fairmont Coal Company at Monongah, W. Va., the most disastrous mine explosion yet recorded in the annals of American mining. The mines were comparatively new and well laid out. Mine No.8 had been in operation only about two years and was the pride of the Fairmont Coal Company. Mine No.6 was first opened ahout four years earlier. In order to make it possible, in case of emergency, for either mine to be ventilated by the ventilating system of the other, the two sets of workings were connected underground. The F face heading of mine K o. 6 led direetly into No.2 north heading of No.8 mine. On Friday, Dcccmber 6, at about 10.30 in the morning, an explosion of unusual violcnce swept completely through both mines, pursuing its course throughout the numerous ramifications and bursting out of the two pit mouths, located It miles apart, nearly simultaneously. The slope of mine No.6 was only slightly damaged, but at the mouth of No.8 the destruction was very great. The fan was wrecked, the engine house was demolished, and mine timbers were blown across Monongahela River: As nearly as can be determined, 361 men were killed in the two mines by the explosion. .While the inspection of the Monongah mines was still in progress, on Thursday morning, December 19, at about 11.20, a similar explosion wrecked the Darr mine of the Pittsburgh Coal Company ut Jacobs Creek, Pu.; 238 men lost their lives in this explosion, which in number of casualties is second only to the :Monongah disustcr in the history of American mining. Of ull thc men in the mine at the , time of the explosion, only one mun, who happened to be within 100 feet of the ~iUrface on an old manway in a wet, unexploded portion of the mine, succeeded in escaping alive. The underground investigation of these mines was made in cooperation with Clarence Hall and ""Valter O. Snelling, of the United States Geological Survey, and James ""V. Paul, now of the Survey but at that time chief of the department of mines for vVest Virginia, to all of whom the author is greatly indebted for valuable assistance, suggestions, and advice. Mr. Paul will rcport on the nature of these explosions, the precipitating causes, their destructiveness, and the general cüliditions in these mines following the disasters. The present report is confined essentially to the laboratory examination of some of the explosive materials collected from these mines directly ufter the explosions.

Jan 1, 1911

By Peter N. Blakey

The Kidd Creek orebody is a massive, base metal deposit with widths up to 600 feet and a strike length of 2,200 feet. The orebody dips eastwards at 70° to 80° and is amenable to sub-level open stoping. Five distinct zones (Fig.1) based on structural wall rocks and ore type parameters occur within the orebody. These zones are: Zone 1 - Mainly copper stringer ore Zone 2 - Massive pyrite ore Zone 3 - Massive sphalerite and chalcopyrite Zones 4 and 5 - Are banded and variable in nature Compressive strengths vary from zone to zone with an average of 22,000 p.s.i. and highs of 40,000 p.s.i. The mine is developed from a ramp extending from surface to the 1600 foot level and a 24 foot diameter, 3050 foot vertical shaft with main levels at 400 foot intervals. Sub-levels at 100 foot vertical intervals are driven from the ramp. transverse and longitudinal pillars to support the crown pillar left under the open pit. The layout allows an opportunity to enlarge or reduce pillar sizes and also to introduce fill on any horizon should conditions warrant. It also offers a large number of operating stopes spread through the various ore zones giving good ore blending characteristics. All ore from the stopes is handled through drawpoints using Wagner ST8 scooptrams with an average one way haul length of 650 feet.

Jan 1, 1976

By M. W. Airth

ON THE 6TH JULY in the year 1953 an announcement was made to the public that touched off one of the greatest staking rushes in the history of mining in Canada and resulted, in tl1e space of a few short years, in the development of the greatest reserves of uranium-bearing ore in the world. It was ?On this date that the famous "Blind River back-door staking bee" was completed with the acquisition of some 2,000 claims by the Preston East Do me-Technical Mine Consultant teams under the direction of Mr. Franc Joubin and Mr. Robert C. Hart. That story has been told from coast to Coast and is too well known now to re-quire elaboration. Suffice to say that, in the short elapsed time of less tl1an five years from that momentous summer of 1953, three of the Algoma mines are in full production, three more are rapidly nearing full production, five more 1are approaching the production stage, a new hard-surfaced highway, 108, has been built to serve the area, and a brand new, completely planned city, Elliot Lake, is being built to provide the amenities of living to the 22,000 people already in the area.

Jan 1, 1958

By Parry. V. F.

"SUMMARY This report reviews the status of the packaged-for industry as of 1941. A field study was made of 35 representative plants to obtain technics and economic data on different types of processes used to make packaged fuel in the Central States. The report includes a classification of processes, photographs of typical operations, designs of different plants, an analysis of costs of manufacture, and a study of the physical and chemical properties of fuel cubes.It was observed that many of the smaller plants were having troubles in the manufacture of packaged fuel as the price of materials and costs of labor advanced toward the higher levels of 1942. In some instances, the total cost of manufacture was as high as $5.00 per ton, while in the better, medium-sized plants it was approximately $3.25 per ton. The direct manufacturing costs, excluding investment and depreciation, ranged from $3.17 to $2.37. These costs permit almost no profit at small plants when packaged fuel sells for the same price as competing lump coal under conditions existing in 1941-42.It was found that the predominant troubles in plants were due to inadequate drying and insufficient mixing of the starch binder. It was ob¬served that in the better plants, where proper mixing of binder was attained high-quality packages were made if 50 to 70 percent of the moisture was removed in the drying ovens. Experimental data obtained in the laboratory show the relationship between the temperature of dry air and the time required to remove different percentages of moisture in wrapped orunwrapped coal cubes.The average physical and chemical properties of fuel cubes made by five processes are listed, and tentative standards for minimum physical qualities and methods for measuring quantity are giver."

Jun 1, 1944

By G. W. Luxbacher

This volume describes the use of the Penn State Mine Ventilation Simulator (PSU/MVS) to model existing mine ventilation systems and, in addition, to evaluate the effect of system modifications. Ventilation survey methods designed to insure computer input data of sufficient accuracy for simulation purposes are covered in comprehensive detail, including quantity and pressure measurement and fan performance testing. The development of input data from ventilation survey results is discussed and illustrated by the use of an actual field survey. Two programs, written in FORTRAN IV with WATFIV, are presented to calculate airway head losses from altimeter pressure measurements. An existing coal mine ventilation system is analyzed and modifications to the system are simulated and evaluated. In addition the application of the PSU/MVS to non-coal mines is briefly discussed. An extensive bibliography on ventilation surveying and simulation is included.

Jan 1, 1977

By J. Drelich

The adsorption of oleate at the surface of titanium dioxide from aqueous solutions was examined by Fourier transform infrared (FT -IR.) spectroscopy using a germanium internal reflection element coated with a thin film of TiO2. This thin film, with a thickness of 100-200 A, was deposited on the surface of a germanium single crystal by RFIDC magnetron reactive sputtering. It was found that significant adsorption of oleate from a 0.02-0.03 mM aqueous solution on the surface of TiO2 thin film occurs at neutral pH, from about pH=5.5 to pH=7.7. Adsorption of oleate at the surface of the amorphous TiO2 thin film appeared to be reversible, involving soap-acid dimers.

Jan 1, 1997

By Robert Bissonette, Samir Sbai

A critical component of implementing autonomous systems is the ability to use information from a robust sensory and information system to make sound, predictable, and repeatable decisions to assure safety. This means that any such system would need to evaluate what objects (people, equipment, boulders, etc.) of interest exist in that environment (with relevant data about identity, trajectory, characteristics, etc.), project a future continuum of those objects (including considerations for variabilities), and make control intervention choices to minimize risk due to exposures in the present operational area. The components of an overall system would include: a) sensor and data fusion, b) probability projection of future states, c) generation and evaluation of alternate futures, and d) implementation of best course of action to reduce risk. The National Institute for Occupational Safety and Health (NIOSH) Spokane Mining Research Division (SMRD) is studying this framework for applications for autonomous mining equipment. This paper focuses on using information from the sensor fusion engine to generate a continuous projection of future and alternate states (b and c above) incorporating the factors of confidence, accuracy, tolerance, and other variabilities. We refer to this as Machine Situational Awareness (MSA).

Jun 25, 2023