Search Documents

By J. K. Whyatt

During the past 2 years, U.S. Bureau of Mines (USBM) researchers reviewed an in situ stress investigation conducted in 1977 at a test site on the 4250 level of the Lucky Friday Mine, Mullan, ID. Although the field measurements of over core strain were found to be useful, significant deficiencies were found in the stress field estimation procedure. The stress field estimate was then updated to incorporate recent progress in statistical capabilities and new understanding of stress concentration factors for doorstopper cells, as well as to correct an error in the original stress solution procedure. Simple models were used to examine the possibility that systematic variations in material properties and stress fields existed at the site. These models succeeded in reducing the sum of squared error somewhat, but fell short of completely describing stress variations throughout the test site. This overcore measurement will be supplemented by two other measurements described in the second and third reports of this series. Other observations of stress field characteristics are discussed in the fourth report The final report will also characterize the natural in situ stress field in the vicinity of the Lucky Friday Mine. This work was undertaken to support USBM research on mining method design and rock-burst control for deep mines.

Jan 1, 2010

By D. S. Burgess

An investigation of the hazard of spillage of liquefied natural gas (LNG) onto water is described. About 2,000 gallons of LNG were consumed in various tests. The initial vaporization rate of LNG following spillage was found to be 0.037 lb/ft2 sec; when the spill was confined, this vaporization rate was moderated after about 20 seconds by the growth of an ice layer on the water surface; when the spill was unconfined, a coherent ice floe was not observed and the vaporization rate was essentially time independent. The maximum diameter (in feet) of the spreading LNG pool was found to be given by 6.25 Wo 1/3, where Wo is the weight of LNG in pounds, Downwind of a natural gas source, time-averaged methane concentrations were given in good approximation by standard air pollution equations. However, peak concentrations were as much as twentyfold higher than average, adding an additional factor to the assessment of hazard. The effect of layering by the cold vaporized natural gas was similar to the effect of a temperature inversion on normal gases in the atmosphere. Small-scale explosions were observed on pouring LNG onto a water surface; no single explanation seems pertinent to all of the incidents observed.

Jan 1, 1970

By C. Chapman, M. G. Reading, M. P. Amsden

Ecstall Mining Limited, a subsidiary of Texasgulf Incorporated, operates the Kidd Creek mine, a 10,000- tpd base metal producer, near Timmins, Ontario. Two different ore types are mined and milled copper-zinc and silver-lead-zinc. At the highly automated Ecstall concentrator, the ores are processed by selective flotation in three individual circuits. One of the most important metallurgical tools for process control is a sample system incorporating continuous onstream X-ray analysis. Recently this system was further automated by adding computer control of reagents for two copper-zinc flotation circuits. The computer programs, utilizing optimum seeking methods and smelter contract terms, have increased copper recovery 0.8% and zinc recovery 1.6%, and reduced reagent costs by 12%. Although not anticipated, copper and zinc concentrate grades were improved modestly as well.

Jan 1, 1973

By J. E. Dutrizac, J. B. O'Reilly

"Zinc is a relatively abundant element which occurs as both high-grade sulphide ores {sphalerite ZnS) and oxide ores which the ancients collectively termed ""calamine"" (smithsonite ZnC03 and/ or hemimorphite Zn4Si201(0H)2 - H20 and/ or hydrozincite Zn5(C03) 2(0H)6). Although oxidic zinc is readily reduced by carbon, the process becomes thermodynamically viable only at - 1000°C, and at this temperature the zinc is released as a vapour (B.P. 907°C). Casual cooling of the vapour results in its re-oxidation by excess combustion air or even the carbon monoxide product of the reduction reaction. ZnO + C = C09,, + Zn vapom Only fairly rapid quenching of the zinc vapour and the isolation of the reduction products from the combustion gases will yield metallic zinc; these conditions were not produced deliberately until the advent of distillation technology. Until quite recently, the principal use of zinc was in brass manufacture; galvanized iron was not discovered until the 19th century and zinc casting alloys are a relatively recent invention. As will be seen, brass could be produced without recourse to a pure zinc intermediary, and the discovery of brass preceded that of zinc by many centuries. The purpose of this paper is to outline the discovery and early development of both zinc and brass with special reference to the European scene."

Jan 1, 1999

By W. S. Tower

STEEL is the basic metal, the main metallic prop of the modern industrial world, a good gage for measuring the state of our complex economy. Any who had doubts on that score should have had them dispelled by the many evidences of public concern over the affairs of the steel industry in recent months. I do not need to relate the various criticisms of the industry, nor the questions about its policies and performance which have come in a rising flood, especially from unthinking and irresponsible sources. But judged from the standpoint of production, or from plans to improve and expand facilities, or from technical progress, the facts about the steel industry are proof of

Jan 1, 1948

By M Grigorescu, J H. Hodgkinson, H Alehossein

A new framework that collates and interprets pre-existing data to assess vulnerability and ultimately plan to avoid or minimise flood-related risk to infrastructure, people, downtime, environment and revenue has been developed. The æClimate Related Adaptation from Terrain Evaluation ResultsÆ (CRATER) method tested at a coal mine in Queensland, provides semi-quantitative information to assist decision makers when designating investment for minimising vulnerability of mining operations to climate. Here we present the processes involved in this three-step approach that uses pre-existing spatial data of the mine site and local knowledge to build a set of visual tools to assist decision-making. The first step of the process is performing multi-criteria evaluation (MCE) within a geographic information system (GIS) on ranked natural conditions at the mine, such as elevation, slope, drainage, soil and vegetation, which is performed to identify critical flood areas. Secondly, a fault-tree analysis identifies how impact can occur and what options there are for impact reduction. Finally, a resource assessment of the mineÆs capacity to adapt reduces the adaptation options to those most suited to the mine. The results are confidential, but for the purpose of introducing the methodology, we present simplified results, particularly of steps 2 and 3. CRATER can also be used for future æwhat-ifÆ flooding scenarios to identify the most suitable locations for roads, buildings or other critical infrastructure. The methodology is transferable to any mine, series of mines or locations along the mining value chain that have sufficient data, providing a practical decision-making tool to identify æno-regretsÆ actions that not only could reduce downtime after or during an event, but in some cases may enhance production between extreme events. We now plan to test this method at a broader scale, to encompass more than one mine in the analysis.CITATION:Hodgkinson, J H, Grigorescu, M and Alehossein, H, 2013. Climate Related Adaptation from Terrain Evaluation Results (CRATER) - interpretation of pre-existing data for mine site flood vulnerability and management, in Proceedings Water in Mining 2013 , pp 259-266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By William Ives

My presentation is from the viewpoint of the industrial mineral geologist, which is a relatively rare breed. Very few geologists become involved with industrial minerals for two reasons, I think: (1) Much of the industry utilizing non-metallic minerals has developed without the use of geologists in the begin¬ning and many of the management people, who generally derive from the processing plant supervision, tend to take raw materials for granted; and (2) non-metallic minerals are a very insignificant part of the curriculum of virtually all colleges granting a geology degree. One learns about the geology of industrial minerals by working with it. This "on-the-job-training" is probably best because it brings the geologist into close quarters with the production people and the production process. And the industrial minerals field has a distinctiveness when compared with the petroleum or metal mining field in that each deposit can yield a material differing in some aspect from that in any other or within the same deposit. The petroleum from a well in a given field will be similar to that from any other well, but a limestone on one side of a hill can differ signifi¬cantly in elemental composition, calcinability, soundness, specific gravity, or some other factor from the same ledge on the other side of the hill. This characteristic of almost certain variability creates problems sooner or later and provides for much of the employment of industrial mineral geologists. My job seen from the viewpoint of management is "Find us some rock we can extract and process at a profit." The industrial non-metallic geologist has much the same problems and approach as a detective. I do not mean the TV variety with the big mouths and the unfailing knack of spotting the wanted criminal immediately in a city of ten million people. Any real detective will tell you it takes leg-work, knowhow, and persistence to make a case. The same is true for the geologist who finds rock which can be quarried at a profit. I am responsible for finding raw materials for a company which manufactures portland cement and

Jan 1, 1977

By James P. Roe

I. INTRODUCTION. THOSE who deem the subject of this paper an old and super¬seded one may recall with advantage the words of the great proverb-maker, bidding us to seek the new in the ashes of the old. The manufacture of wrought-iron began with the small hearth built upon an eminence, and relying on the wind for blast. Next came, either the hearth about 12 in. in diameter by 2 ft. in height, blown by a man operating two goat-skins for bellows, or, a hearth of greatly varying diameter and about 10 ft. high, depending for its blast upon natural draft. The former appeared in India, the latter in Burmah; and both were in operation until quite recently, though their origin is lost in prehistoric times. The Catalan forge was the evolutionary descendant of the foregoing, and the parent of the Blase-ofen, which in turn led to the high bloomary or " Stückofen," the father of the blast-furnace, as a producer of cast-iron. The production of cast-iron checked the growth of the direct processes; and led to the introduction of various hearths, such as the Walloon, for low-silicon irons; and the South Wales process, combining the run-out fire with the finery, for higher-silicon irons. Some of these are still in operation in localities possessing the necessary raw materials; and their product is used for purposes requiring wrought-iron of exceptional quality, the supply of which is still smaller than the demand. We have to look back but a century and a quarter to see the introduction of the puddling process by Henry Cort; a process which, reinforced by the iron-oxide bottoms and fettling of Hall, was not less revolutionary in character, and more revo-

Jul 1, 1905

By N. Som

The pile capacity in cohesive and granular soils depends on a number of parameters. The values of these parameters as recommended by Indian Standard Code of Practice vary over wide ranges. A designer often finds it difficult to select appropriate values of these parameters for realistic estimate of a pile capacity. The present paper makes a critical review of the values of the parameters given in Indian Standard Code of Practice and suggests a realistic approach to selecting them in the light of recent research.

Jan 1, 1996

By Frank E. Cash

"INTRODUCTION The iron—ore ranges in the Lake Superior district are the Marquette in Michigan, Menominee and Gogebic in Michigan and Wisconsin, and the Cuyuna, Mesabi, and Vermilion in Minnesota. These ranges produce about 85 percent of the iron ore mined in the United States. Accident experience in connection with this production is better than that of the regions producing the remaining 15 percent. Production and shipments vary slightly from year to year but closely approximate each other over a period of years.This information circular supplements, continues, and combines the data in Information Circular 7321,2/ including figures of 1944 and 1945.During the 6—year period 1940 to 1945, inclusive, 481,485,475 long tons of iron ore was shipped from the Lake Superior district. 4/ Michigan and Wisconsin shipped 93,787,648 tons, or 19,5 percent of the total, and employed annually an average of approximately 14,300 men; Minnesota shipped 387,697,827 tons, or 80,5 percent, and employed annually an average of approximately 9,300 men. The tons produced per man employed is much greater in Minnesota than in Michigan and Wisconsin, owing to the large open-cut production in Minnesota."

Jul 1, 1947

By Raymond B. Ladoo

Deposits of talc are known in many districts in Canada but at the present time active mining operations are reported only in Ontario . Here three companies are now operating, two of which, George H. Gillespie & Co. , Ltd. , and the Anglo- American Talc Co. , are at Madoc . The operations of the former company are probably the largest and best known in Canada . The writer , in his capacity as an engineer of the U. S. Bureau of Mines , was permitted by this company to make an inspection of its mine and mill in June, 1920 , and study the methods employed . This information was desired for comparison with methods employed in the United States . The following description is based on observation made during this visit , supplemented by data supplied by the company .

Sep 1, 1920

By C. V. Millikan

THE year 1930 in the petroleum industry has been characterized by the establishment of large potential production of crude oil. This has resulted in closer cooperation between companies by proration and unit operation agreements in order to afford an equitable outlet to all, and to prevent a flood of oil being forced on the market with attendant tremendous material and economic waste. Drilling wells in proved areas and wildcat wells are fewer than in the past several years. Restricted production and low prices have caused greater effort to increase producing and recovery efficiencies. Increased refinery efficiencies have amplified the effect of overproduction. Pipe line departments have been especially busy. New oil lines have reached more refineries by new and shorter routes. Establishing greater gas reserves by new fields has justified new gas lines to industrial centers, and has brought this fuel to thousands of new domestic consumers. Two long gasoline lines, a new venture in pipe lines, are being built to obtain a lower cost of transportation and less loss between the refineries and their distribution centers. The chairmen of the various divisions have discussed the developments of their respective branches more fully in the following reviews.

Jan 1, 1931

By John Rajala

The Otjikoto Gold Mine in the Republic of Namibia is located approximately 300 kilometers north of the capital city of Windhoek. The project features surface mining with a modern gravity/carbon-in-pulp mill for ore treatment and recovery of gold. Initial mill design capacity was 2.5 million tonne per annum but then expanded after 9 months of operation to 3.1 million tonne per annum. The technical steps to establish the Otjikoto mill design from process selection in the due diligence stage, through flowsheet development in the feasibility study followed by detailed engineering design are reviewed in this paper along with mill performance during start-up and in 2019.

Oct 30, 2020

By Ted DePooter, Mun Wei Leong, Chad Frederick

Downtown Bellevue Tunnel (DBT) is part of Sound Transit’s $3.7 billion, 14-mile light rail transit system from downtown Seattle, across Lake Washington, to the cities of Mercer Island, Bellevue, and Redmond. The tunnel was the first Sound Transit East Link project and posed significant construction risk. This paper discusses implementation of design changes to the soft ground tunneling method, implementation of several technologies such as the use macro-synthetic fiber initial shotcrete lining, use of spray-applied waterproofing, and use of shotcrete for the final tunnel lining. These efforts allowed for significant time and cost savings to the project.

Jun 13, 2021

By D-J Min

Strategies and achievements in the Asian steel industry to construct industrial ecological chain are reviewed largely in the case of Japan, Korea and China. Emphasis is placed on the development of resource circulatory system for the minimisation of various wastes and emissions of green house gases (GHG), toxic gases and polluting particulates. The minimisation includes:Rationalisation of iron and steelmaking processes; Implementation of available relevant measures/technologies; Life cycle assessment in designing steel from semis to assembled products; Reduction, reuse and recycling of materials and energies; and Utilisation of core competence technologies to process domestic and industrial wastes. In view of global nature of the above wastes- and emission-issues, inter-industrial linkage and international cooperation across the borders in the Asian countries have become more important. Inter-industrial linkage definitely serves to cut back the wastes and emissions. Examples of such linkage and factors influencing the sustainability of the linkage are described with expectation for further development of the linkage. Importance of international cooperation cannot be overstressed under the circumstances where steel production in China exceeded 220 Mt and world production exceeded 945 Mt in 2003 and is still increasing. Practical measures are discussed to enhance the linkage and cooperation for effectively promoting the reduction, reuse and recycling, including implications for the nonferrous industry.

Jan 1, 2004

By David M. Rempe

The purpose of this standard is to provide a method for testing of cushion materials that leads to uniform results when employed by various organizations and laboratories. The load-deflection characteristics measured using this method are intended to provide input data for analysis of pile driving, as in wave equation analysis of pile driving. It should be recognized, however, that there are several factors which may cause a difference in performance between the test samples under laboratory conditions and actual cushion materials under pile driving conditions. These factors include variations in material properties from sample to sample, compaction and/or deterioration of the materials with use, eccentric loading due to misalignment, confinement effects or the cushion container or inter layered materials, head buildup, rate of loading, etc. In order to obtain representative load-deflection characteristics, therefore, testing of cushion specimens which have been subjected to actual pile driving conditions is encouraged 1 such specimen should be tested at various stages of the useful life of the cushion. The users of the data are cautioned to determine if the particular wave equation program they are using requires either the secant or tangent definition of the stiffness and modulus of elasticity.

Dec 1, 1984

By W. E. Armstrong

Gypsum was first exploited as ?a commercial proposition in this province by the Union Mining Company which, in 1900 opened quarries on the east shore of Lake Manitoba, near the present site of Gypsumville. This company established a mill at the head of Portage Bay on the lake, and the manufactured plaster was carried by the companies boats to McArthur's siding on the Whitemouth river near Westbourne, Man., from which point it was distributed. In 1904 a reorganization took place and the Manitoba Gypsum Company Limited bought out the original company, and operated the original mill for about one year when it was destroyed by fire. There were many factors which rendered the operation of a mill at the quarries very difficult; lack of rail transportation for bringing in supplies, and the impossibility of local power development made manufacturing costs very high. Satisfactory distribution could not be affected because of water transportation and poor terminal facilities at McArthur's siding. For these reasons the new mill was built at Winnipeg, where cheaper power and better distributing facilities permitted the industry being placed in a better position. The company continued to bring the gypsum rock by steamer to Totogan, from which point it was transported by rail to Winnipeg. This period was one of steady expansion as the product became better known and more universally accepted as a wall finishing material. Unfortunately, in 1909, this new mill was destroyed by fire, causing a serious set-back to the company, at a time when the steady growth of the western market gave every promise of the industry being placed on a profitable basis.

Jan 1, 1925

This paper deals with the evolution of Canadian shaft sinking technology over the last 15 years. Most, if not all, shaft excavation projects in Canada prior to 1990 were sunk using traditional benching methods with labour intensive equipment. In the late-1980s, J S Redpath Limited of North Bay, Ontario, Canada, were contracted to deepen the shaft at Atomic Energy of Canada LimitedÆs Underground Research Laboratory (URL) located in southern Manitoba. The laboratoryÆs role was underground hydrological and geomechanical research, so the project offered both time and opportunity to conduct additional experiments while sinking. The offshoot of the research program was the true birth of the Canadian version of full-face, long round shaft sinking technology. Throughout the 1990s, this sinking method has been further refined over a number of shafts. The results have been faster sinking rates, a safer work environment and an overall improvement in project economics.

Jan 1, 2002

By Alberto Pesamosca

The present work analyzes the latest results achieved in scrap based EAFs in terms of application of chemical energy, starting from the observation that the general trend is a reduction of oxygen utilization. Consequently a review is needed about criteria for evaluation of melting process efficiency and equipment design. If from one side the maximization of productivity remains one of the major goals, from the other side some aspects of present market situation, included price of raw materials, are requiring the maximization of process yield. Based on achieved performance figures of selected plants and theoretical considerations, the effect of chemical energy input intensity is analyzed focusing on transformation cost, productivity and total energy input. The effect of present practices with lower oxygen utilization is considered also in terms of global CO2 emissions. Finally, the latest Danieli concepts and technological tools for optimization of chemical input are presented.

Aug 17, 2017

By T. W. Guy

During the past three years the Surface Preparation Committee of the American Mining Congress Coal Operators' Committees has been collecting data on dewatering and drying washed coal, and on screening coal in representative plants in the Eastern and Central bituminous fields. Because of wide variations in bed moisture, such data can be compared only after deducting the bed moisture. It was found that practically every company used a different routine for moisture sampling and determinations. Some reported the moistures as total moistures, others as surface moistures, air-dried moistures, or oven-dried moistures. For most of the reports it was necessary to estimate, from a consideration of the bed moisture and other data available in a given case, corrections to be made in order to obtain surface-moisture figures as a common basis for comparison. At any plant, and regardless of bed moisture, the percentage of surface moisture remaining in a product when the dewatering, or a given stage of the dewatering, has been completed, is the real measure of what has been accomplished. The descriptions and data given with Fig. 1 show that surface-moisture figures show relationships that would not be shown by total moistures. Therefore bed moisture should be deducted, or, if more practicable, the surface moisture of the products should be measured direct. A preparation engineer finds one per cent, or even a part of one per cent, of surface moisture a very important consideration in the results of his efforts to find the most effective and economical methods of reducing and controlling the surface moisture in his products within the required limits. Therefore it is important for him to have accurate measurements of surface moisture with minimum uncertainty as to whether they sometimes include less than the surface moisture and at others all of the surface moisture plus an unknown part of the bed moisture. The Problem We know that pieces of coal have a capacity for holding water: (1) inside themselves, which is a natural characteristic of the bed from

Jan 1, 1938