Search Documents

By T. L. Turner, Daniel T. Rogers

As part of a program to investigate technology for the extraction of studied HNO3 alumina from abundant domestic ores , the Bureau of Mines leaching of calcined Georgia kaolinitic clay . In this investigation , iron impurities were removed from the aluminum nitrate pregnant leach liquor by solvent extraction , and the purified liquor was evaporated to prepare a suitably concentrated crystallizer feed liquor . Aluminum nitrate nonahydrate was crystallized from the liquor to separate the aluminum from undesirable trace elements and excess water . Continuous crystallization at 40 ° C in a pilot plant vacuum evaporative unit was performed for 5 days to observe the effects of impurity buildup under minimum bleed- stream conditions . Liquor feed rate was 26 lb/h and AAll (( NNOO33 )) 33..99HH22O0 ((AANNNN)) crystal production rate was 17 lb/h . Fe 203 and Cr203 were not effectively separated from the crystals , and P205 , MgO , and K20 impurities must be removed by recrystallization . Other impurities did not excessively contaminate the crystals . Washing the crystals with water or aqueous HNO3 gave an equivalent increase in crystal purity levels by displacing mother liquor . Theoretical equations , applicable to any continuous evaporative crystallization of developed to produce material balances for engineering ANN , were applications .

Jan 1, 1965

By E. P. Williams

"Prince Edward Island, Canada's smallest Maritime Province, is located in the southwestern part of the Gulf of St. Lawrence. The Province is more or less centrally located in the Maritimes Basin, a large intermontane basin within the Appalachian orogenic belt. The Maritimes Basin is subdivided into sub-basins and uplifts which exhibit two dominant structural trends: east and northeast. The Basin is known to be petroliferous because of the seeps, shows, oil shales and albertite found in southern New Brunswick and northern Nova Scotia and the gas and oil produced from the Stony Creek field near Moncton, New Brunswick.Permian beds are exposed on the Island, mostly along sea-cliffs. A maximum thickness of about 5,000 feet of red beds -shales, sandstones and conglomerates -make up the sequence. Over most of the Island, the Permian section is much thinner. Four key wells (Mississippian tests) and several shallower tests have been drilled. The Pennsylvanian-Mississippian section thickens rapidly off the Port Hill Uplift at the northwest, where it is less than 4,600 feet thick, and continues to thicken to about 20,000 feet in the Cumberland Basin at the southeast. Geological and geophysical data combine to give us the structural picture of the deeper beds.Prospective reservoir rocks are primarily in the Missis-sippian Horton and Windsor groups. Prospects are:-1. on or over structural highs in the basement; 2. on anticlines or fault highs; 3. over or peripheral to salt domes or salt-core anticlines; 4. at truncation pinchouts of Mississippian prospective beds; 5. in basal sandstone or granite wash on the pre-Carboni-ferous basement; and 6. in facies traps at changes from sandstone to shale or porous to tight carbonate rocks."

Jan 1, 1967

By Shi Wang, Hongbin Liu, Meiliang Wei, Wu Liu, Xiaojun Wang, Yuxian Ke, Xuepeng Song, Tiejun Tao

The study investigates the influence of water migration on the fluidity of fresh cemented paste backfill (CPB) with and without flocculant under variable shear rates. The research utilizes nuclear magnetic resonance (NMR), rheological tests, and scanning electron microscopy (SEM) to analyze water migration, rheological properties, and microstructure evolution. The findings reveal that water migrates to more stable states as shear rate increases, and the addition of flocculant enhances water migration and increases shear stress and apparent viscosity. The study establishes relationships between water content and rheological parameters, providing insights into the flow characteristics of fresh CPB for pipeline transportation.

May 4, 2022

By A. J. DeArdo

Linepipe steels have come a long way in the past forty years. In fact, modern, high strength steels for large diameter linepipe applications represent one of the seminal accomplishments in metallurgy of the past half-century. The synergy of advanced steelmaking, alloy design including microalloying, hot rolling, and interrupted accelerated cooling has led to the marvelous steels being used today. The drive for higher performance pipelines has been motivated by the energy sector of our global economy who wanted both higher throughput capacity, i.e., larger diameters and higher pressures, and lower material cost, i.e., relatively thinner gauge wall thicknesses. These requirements led to new steels with higher strengths, better toughness and improved weldability. The goal of this paper is to trace the evolution of linepipe steels from the X60 grades of the small diameter pipelines of the 1960s to the (X80 - X120) grades used in the large diameter pipelines of today. The metallurgical triumphs permitting this success story, e.g., clean steel practices, controlled rolling, microalloying with Nb, and using IAC to obtain low temperature transformation products, will be highlighted and discussed.

Jan 1, 2005

By Haley, D. F.

WHEN operations were first started at Climax in 1917 by the Climax Molybdenum Co., they were pioneering in the molybdenum industry for little was known relative to the uses of molybdenum or the metallurgy of molybdenite concentration. Concentration of molybdenite is relatively simple today but in 1916, when the Climax deposit first attracted attention, it presented serious difficulties. Little was known, in fact, even about the assaying of such low-grade molybdenum ores. Mine samples were sent to at least a dozen of the best laboratories in the United States and average values reported varied from 0.4 per cent to 1.0 per cent MOS2. Owing to the wide variations in MoS2 content obtained from reliable chemists, the actual value of the ore was most uncertain. This variation occurred repeat¬edly over a period of six months in 1917. It was finally decided, as a last resort, to cut several tons of sample from the tunnel and have a mill test made, using the recovered MoS2 per ton as the grade of the ore, for a small error in the assaying of the concentrate would not materially affect the results. These mill tests were made by the General Engineering Co. (Callow) at Salt Lake City. The results proved an ore of commercial grade and indicated the flotation process for the best metallurgy. Based upon these tests, the decision was made to build a 200-ton flotation plant. At this time, the art of flotation was

Jan 1, 1946

By Rustu S. Kalyoncu

A major goal of the Bureau of Mines is to conserve the Nation's mineral resources by developing improved performance materials. In support of this mission, a survey of the state of the art of chemically bonded refractories has been made, covering the scientific literature, government reports, and patents. This review includes research and development results for phosphate, silicate, oxychloride, oxysulfate, and other bonding agents used in refractories manufacture. A significant finding of the review was that references on bonding mechanisms, bond formation kinetics, and other important process parameters and conditions were few and universally vague. As a result, recommendations are made to expand research efforts to investigate the kinetics and mechanisms of reactions in chemically bonded refractories.

Jan 1, 1982

By James E. Lawver

The agriculture industry has made great strides during the past decade to increase agriculture yields through increased use of fertilizers. Increased use of fertilizers may prevent or at least delay mass starvation due to the alarming increase in world population. Phosphate was added to soil as a plant nutrient in the forms of calcined bones at least 2 000 years ago, (1) and man has used phosphate minerals as a source of fertilizers in one form or another for at least 100 years. During 1977 the world produced about 116 million metric tons of phosphate rock, with about 86% used for fertilizers and another 4% for animal feed supplements. More than three-fourths of the total production comes from the United States, Morocco, and the Soviet Union. From a mineral beneficiation point of view, the major sources of phosphate rock and the methods of beneficiation can be classified as follows. Marine deposits not containing appreciable carbonate minerals, marine deposits requiring a francolite carbonate mineral separation, igneous deposits not containing appreciable carbonate minerals, and igneous deposits, requiring an apatite carbonate mineral separation.

Jan 1, 1978

By S Hapugoda, J R. Manuel, M J. Peterson, A Poliakov, E Donskoi

################

Aug 12, 2013

Mineral processing is an energy and water intensive activity. Mill comminution equipment usually has high energy requirements which necessitate extensive cooling to remove heat. Cooling requirements are typically 10% to 20% of the comminution energy. If there is an adequate supply of suitable water, open water-based cooling systems are the simplest, cheapest and most energy efficient cooling method available. This paper describes a method to determine the water demand for open water-based cooling systems at a plant and to determine whether the mine has sufficient water to meet that demand.

Jan 1, 2014

By D. Berkley

Off-gas systems often become the limiting factor in production increase and environmental projects. Any upgrade or new off-gas project needs to address control instability issues, instabilities that can result in safety hazards, significant loss of system capacity and/or emissions to the environment [1]. In addition, the design engineer must optimize system configuration and equipment size for the new operating conditions, to have a technically feasible and economically viable project. Dynamic simulations can be used for addressing both the control stability and the design optimization issues. This paper illustrates how the dynamic simulation of transient processes and of their control system can be used in "real life" situations for these purposes, presenting the example of an electric furnace off-gas system design.

Jan 1, 2005

By D. M. Hausen

A computer program has been developed by Newmont Exploration to convert mineralogic data by XRD into rock type and ore type classifications. This method has proven useful in identifying lithology from cuttings samples, where percussion drilling was an alternative to expensive core drilling. Computer printouts of rock type and ore type identifications can be generated simultaneously with mineralogic analyses, resulting in a considerable time savings in manual calculation. XRD-computer logging was first applied to the Carlin mine in north central Nevada, and later to the Maggie Creek and Gold Quarry gold deposits, southeast of the Carlin mine. Impure Paleozoic limestones of the "lower plate" Roberts Mountain Formation and the "upper plate" transitional facies have been decarbonatized to altered siltstones and shaley units along vertical faults and permeable stratiform horizons. Advanced stages of decarbonatization were accompanied by silicification. Quantitative XRD data are initially sorted into principal rock type units (limestones, siltstones, dolostones, shales) based on major mineralogic components (calcite, quartz, dolomite, clays). On the basis of relative amounts of less major constituents, descriptive subclassifications (dolomitic limestones, dolomitic siltstones, argillaceous cherts) are made. XRD lithologic data provide assistance in correlating lithologic units, and delineating favorable replacement horizons associated with gold mineralization.

Jan 1, 1982

By M A. Wells

The various mechanisms by which phosphorus (P) occurs and is distributed within banded iron formations (BIF)-derived iron ore are examined. In unenriched, precursor BIF P occurs predominantly as discrete grains of primary apatite. In high-grade ores hosted mainly by the Brockman Iron Formation, P occurs in three main forms:1. as secondary apatite;2. other submicron, P-rich phases (eg Rare earth containing minerals (REE), vivianite, strengite,wavellite) present in pore networks; and3. as P occurring with iron oxides, in particular, goethite.However, the presence of secondary P-bearing phases does not contribute signifi cantly to the total P level in iron ore, and it is P associated mainly with goethite, which represents the most common occurrence of P in these ores.No direct evidence for the replacement of Fe by P within the structure of synthetic goethite has been demonstrated. Therefore, it is most likely that in iron ores P associates with goethite in occluded form as adsorbed PO4 3- species or as discrete P-bearing minerals, such as strengite, wavellite or vivianite, in ultra-fine, micro-pores or within intra-domain regions of multi-domainic goethite. Such occluded P is not easily extracted with commonly used lixiviants, such as weakly alkaline leachates. Recent development of a low temperature-alkalie/water leach extraction method has been successful in reducing not only the P content, but also amounts of Si and Al inthe initial ore. Refi nement of such a method to commercial application will have enormous benefit in realising the economic potential of large tonnages of high-P (ie >0.07 wt per cent P) bearing iron ore.

Jul 11, 2011

By Alfred W. G. Wilson

THE ultimate purpose of the Chemical Manufacturer is to produce consumer products which can be sold to customers. Such production and sales can be continued only if the operations yield a profit to the manufacturer and if the products meet the requirements o the consumer--bath parties to the transaction must be satisfied. There are vast numbers of consumer products, made by chemical pro-cesses. The production of some of these ultimate products may involve the use of several intermediate chemicals, applications of few or many different processes, and the utilization, somewhere in the series of operations, of a variety of raw materials. On the other hand, some ultimate products have a very simple chemical history between raw materials and end products. There are no chemical products in use which are completely independent of the mineral industry. For many, the association is direct and obvious; for others, it may be indirect and even obscure. Analyses of the process and raw-material ancestry of a very large number of consumer products would suggest that many products are derived from Industrial Mineral products directly, that there are many in which the connection is indirect, and that there are only a few products with which industrial minerals are not in some way or other associated. The vast majority of the more important chemical products, and especially the basic chemicals from which other products are made, are directly dependent for their production upon Industrial Minerals or their derivatives. In the preceding part of this paper, for each raw material mentioned some references have been made to the leading chemical products based on this material. This, however, is only part of the story, because in most cases the consumer product can be made from any special raw material mentioned only by the use of other materials or chemicals made from them. The production of consumer chemicals is really possible only through an intricate interlocking of processes, materials, and apparatus.

Jan 1, 1940

By Herbert Tomlinson

The United States Bureau of Mines has engaged in a study of the conditions under which coal mine accidents, resulting in the loss of life, limb, or time to the injured person, occur from falls of roof and coal. This publication is devoted to the results of a study conducted in the coal mines of the Book Cliffs and Wasatch Plateau coal fields of Utah. To show the necessity of this study, a statement of the fatalities that have occurred during the period 1928-1930, inclusive, in the bituminous mines of the United States and of Utah, is presented (Table 1), followed by a brief description of this Utah district, its coal beds and immediate roof, thickness of cover, dip of coal beds, methods of mining, supervision, roof testing and timbering for roof support, all of which are factors in any plan devised for preventing accidents from falls of roof and coal.

Jan 1, 1932

By C. S. Parsons

Ore-Testing laboratories are maintained by the Mines Branch, Department of Mines, at Ottawa for the purpose of conducting experimental test and research on ore treatment. Sample shipments of a few hundred pounds to car-load lots of Canadian ores are received on application for experimental tests, and all possible methods of treatment are investigated. Reports are issued to the shipper, containing the results, with recommendations as to the most economical method of treatment. These reports have been of valuable assistance to mining companies in the preparation of plans for the design and equipment of their treatment plants. Investigations have been conducted on ores and metallurgical products from all parts of the Dominion. The ores from practically every producing mine and important mineral occurrence have been investigated in these laboratories.

Jan 1, 1931

By Kenneth R. Farley

The Bureau of Mines developed a rapid and accurate flame photometric procedure for determining cesium and rubidium in ores and in products associated with the extractive metallurgy of these elements. The effect of associated ions is neutralized by addition of buffer solution; alkali metal effects are neutralized by parallel analyses made on standard solutions similar in composition to the sample being studied. The overall accuracy of the method is within 2.5 pct of the amount of cesium or rubidium present; the range from 1 to 25 pct is the most accurate.

Jan 1, 1966

By Charles D. Sutton

Safety is an important part of the everyday activity for the explosives industry. The overall accident experience has not been adverse, however, many insurance companies have eliminated coverage for explosive related activities. The Nobel Insurance Group has responded to this insurance problem for our explosives customers. It is vital that safety efforts continue for all aspects of the business. The continuation of insurance policies for explosives, clearly depends on safety.

Jan 1, 1987

By Gustav Wafe

"INTRODUCTION The discovery in 1901 of ""gusher"" oil production at Spindletop, Tex., Tex., a salt-dome structure, led to exploratory drilling on other known domes and known domes and in areas contiguous to salt domes in the Gulf Coast region of Texas and Louisiana. Early drilling on the flanks of the domal structures disclosed incompetent 3/ shales, which flowed into the hole when attempts were made to drill through them. Often these shales seized the drill pipes and presented with equipment then in use, an insuperable barrier to deeper drilling. The obstructing incompetent shales came to be called ""heaving"" shales by drillers who attempted to drill through them. Formations of this type have hampered the penetration of the drill bit in many area in the Gulf Coast region to such an extent that the drilling of wells through heaving shale has become a major problem."

Mar 1, 1942

By Frederick G. Tickell

GEOLOGISTS have been quick to adopt new methods in locating new oil fields and in finding the extensions, laterally or at depth, of the old fields. For most of these new methods he is indebted to the physicist, the engineer, and the chemist, although he has also drawn from such ordinarily unrelated sciences as bacteriology and protozoölogy. These last-named sciences have been of help in problems dealing with the origin of petroleum and, although not of direct application to oil finding, have furnished evidence of value in learning what oil is made from and what are the natural agencies involved in its formation.

Jan 1, 1932

By P Micale

Geological data provides the foundations for the mining value chain. It is used to underpin the modelling and planning and consequently optimise downstream business decisions. However, it is often forgotten or taken for granted. End users often assume the data to be sound without verification. Geological data can be considered a company’s number one asset. Subsequently, the storage, use and management of this data need careful curation and time invested in preserving and protecting it. An established polymetallic mine with 20 000 drill holes could have a data replacement value in excess of $500M at 2020 prices, excluding labour and salary costs. The Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (the ‘JORC Code’) provides guidelines for Public Reporting. Within the code, Table 1 requires discussion around the different types of geological data, its collection and use. What is needed is additional details regarding the validation and integrity of the geological database. A comprehensive guideline specifying minimum geological standards for geological databases has been developed. This expands on the critical points outlined in Table 1 of the JORC Code. This guideline can be used by companies where geological databases are managed in-house or used to assess these services’ outsourcing. This guideline will ensure that geological data is reliable and unadulterated and can be used with confidence. Using this guideline will assist in preserving the investment of geological data in the mining value chain

Mar 22, 2022