Search Documents

By Scott G. Britton

This chapter discusses the necessary construction techniques for installing coal mine ventilation devices. Included in the discussion are the major air controlling devices called over- casts, regulators, stoppings, and doors. Under-casts, although a valid device, are used infrequently in coal mining and are not discussed here. Typically, coal mines require a great many ventilation devices to control the air movement. Post-I969 mines have had to design their air systems to comply with the Federal Coal Mine Health and Safety Act (CMHSA) as discussed in Chap. 1. Pre- 1969 mines have had to redesign major portions of their systems to comply with the basic components of the law such as separation of air courses, single unit split ventilation, and minimum air quantities. It is not uncommon, therefore, to find a large mine (2.0 Mt/a) requiring several hundred overcast installations (permanent, as well as repeat construction), plus doors and regulators placed among a thousand or more stoppings. When each of these devices is subject to leakage from installation and weathering defects, the importance of effective construction becomes evident. An historic rule of thumb for average mine ventilation says that about 70% of all the air pressure generated by the mine fan is lost between the portal and the working faces. Of course, this rule is subject to many factors, but the message is clear: there is a tremendous inefficiency in controlling leakage through common air devices. This chapter strives to present a standard approach and design alternatives which can go a long way in reducing this leakage, and hence, ventilation costs. Historically, mine ventilation has progressed from natural, or draft ventilation, to fire-induced ventilation (Fig. l), furnace-fired centrifugal fans and finally, to today's modem mine fans. Underground controlling devices have been in use in the coal mines since the late 1600s, but the CMHSA of 1969 was the real turning point for mine ventilation. Minimum quantities and velocities of fresh air were required for mining, forcing coal operators and engineers to reevaluate and improve their systems. As a consequence, the cost for ventilating air increased. Today, companies face a variety of choices among design alternatives, materials, labor, and costs of ventilating devices for their mines. The best approach for any individual company or mine is determined by (1) the needs of the mine, and (2) the local design parameters. In my discussions of ventilation construction I shall be fairly general in terms of device installation steps, where specifics are warranted for clarification, I will include this information.

Jan 1, 1983

Hazardous waste has often very complicated chemical compositions in a variety of physical forms and is normally processed in rotary kiln incinerators. Due to large variations in waste types and difficulties in feed characterization, the complex transport processes within the incinerator are not well understood, and the incineration process meets challenges in a smooth operation, and expects various uncertainties in the process chemistry and emission control. For better understanding of the incineration process, simulation was carried out by using Computational Fluid-dynamics (CFD) to characterize temperature and species distribution in the incinerator. In order to catch certain aspects of thermal and chemical behavior, a novel approach is proposed to represent approximately the waste streams and the subsequent combustion process. Hazardous waste in various forms from an industrial-rotary-kiln waste incinerator is firstly converted to a hydrocarbon-based virtual fuel mixture with approximately the same HIC molar ratio and calorific value. The simulation of the combustion process of the simplified hazardous waste was proceeded with a combustion model. The distribution of temperature and chemical species especially the remaining CO in the system is preliminarily investigated. Distribution of CO concentration, as a good indicator of emission level for the incineration process, could be used to evaluate the emission control. The predicted temperature distribution has been compared with available measurement data from an operating rotary kiln waste incinerator at A VR-Chieme, in the Netherlands. Reasonable agreement has been reached between the measured and predicted temperature data. [n the next step, measurement of species distribution in the system is planned to further validate the combustion model.

Jan 1, 2003

By Robert J. Anderson

"Introductory Statement:In melting the nonferrous metals and alloys for foundry and rolling-mill work, even with the best practice, there is always a loss, due principally to oxidation. Melting losses are a serious source of financial loss in brass and bronze practice, but they are especially serious in the case of aluminum and its light alloys because of the relatively high price of aluminum. The indications are that the melting losses in many aluminum foundries of the United States are at times high, and in some plants (especially where certain furnaces are used) they are entirely too high when compared with the average practice. The fact that the oxidation losses in melting aluminum and its light alloys are high is well known, but it is doubtful whether the factors governing the most suitable methods of melting for a minimum of dross are equally well known. The metal losses involved in melting are worthy of especial attention now because of the rapidly growing importance of the aluminum industry.Factors in the operation of furnaces which affect metal and fuel losses:The essential requirements in the commercial melting of any metal or alloy are that the melting losses should be low, the melting should be rapid, and the melting cost should be low. Certainly it may not be possible to obtain these requirements in any furnace selected at random, and it follows that the design and the operation of furnaces for melting different metals are subjects that warrant the most extensive study and tests. As a general rule, in the industrial operation of furnaces, run on aluminum and aluminum alloys, an effort is made to keep the dross and oxidation losses as low as possible. In attempting to hold dross losses low, numerous factors involved in metal melting may be overlooked, or at least disregarded, and the net practical result may be that the furnace is exceedingly wasteful of fuel. In the case of aluminum and its light alloys, the effect of increasing the temperature of melting, at least in an atmosphere containing free oxygen and nitrogen, is to increase the net melting loss."

Apr 1, 1921

By S. Kevin McNeil, William Joa, Catherine Johnson, S. Omar Garcia

The geometry of an explosive is known to have a fundamental effect on the resulting shock wave propagation. Typically researchers use a spherical or hemispherical geometry in order to simplify the shock wave so that resultant overpressure and impulse are uniform in all directions. The goal of this research is to understand the overpressure characteristics from a sheet explosive, a geometry often utilized for breeching in the military. In training alone, soldiers can be exposed to several tests per day, which may be contributing to the prevalence of blast induced mild traumatic brain injuries. Using PCB pressure transducers and high speed video, it was found that as the angle departed from normal (perpendicular) to the face of the sheet explosive, the over pressure decreased significantly. When in line with the plane, a decrease of over pressure by as much as 20% was observed. Time of arrival was roughly 20% faster directly in front of the charge with a pressure amplification of 46% relative to a spherical baseline charge of the same mass. This testing may reveal a more complete relationship between the pressure and angle from the explosive that could have applications for military and law enforcement with respect to best practices on blaster location for reduced over pressure exposure.

Jan 1, 2019

By J. J. Forbes

Ventilation is the most important safety factor in the production of coal because on it depends the safety, health, and efficiency of those who work underground. Without adequate and efficient means of supplying fresh air to the working faces, mining could not have advanced as it has. The extent of the workings, the increase in mechanization, and the increasing use of electricity are largely responsible for changes in methods of ventialtion. Ventilation in the early, days of coal mining was accomplished by means of a natural draft, created principally by a difference in the weights of columns of air between the intake and return openings: Later the furnace was introduced for the purpose of increasing the quantity of air in circulation. Mines continued to become larger, their output increased, men were employed in greater numbers, and more fresh coal surfaces were exposed. Coal beds near the surface, and practically free from explosive gas became exhausted, and deeper beds that liberated methane were opened as development advanced. Mechanical ventilation became necessary and was first accomplished by disc-type steam driven fans she old-.fashioned steam driven disc fan has generally been supplanted by the powerful electrically operated centrifugal fans in use at modern coal mines. In order to be secure against gas explosions and provide ample fresh air for persons employed in large coal mines, air must be conducted through the mine to all working places and to all other unsealed parts of the mince in sufficient quantities to dilute and render harmless all dangerous and noxious gases.

Jan 1, 1929

By R. Shields

"Hard rock mines move large volumes of material. But the conveyors essential to this movement suffer lots of problems, including carryback, spillage, dust, and belt wander. Many of these issues are created at the transfer points where the belts are loaded. This presentation will start with an overview of the latest transfer point systems that incorporate safety and serviceability by design. It will then report on recent projects. One project is the Conveyor B Transfer at the Coeur Rochester silver mine near Lovelock, Nevada. Here performance was improved with the installation of belt support cradles, engineered chute walls with external wear liner, and a compact dust collector. A second project is the improvement of belt support idlers and skirtboard sealing in a long loading zone of a conveyor under the concentrator at an Arizona copper mine. THE IMPORTANCE OF TRANSFER POINTS Conveyors are essential in mine material handling. Their performance will often make the difference in mine productivity and profitability. A key to conveyor performance are the transfer points where the conveyor belt is loaded and discharges. At these transfer points, many of the problems encountered with the conveyor system are created. The problems that arise at the transfer stations include off-center and segregated loading, mistracking, blockages and plugging. And there are a variety of problems originating with fugitive material—cargo released in the form of carryback, spillage, or airborne dust—that are created or exacerbated in the transfer points. These fugitive materials turn into other conveyor-related problems, including shortened component life, unplanned outages for conveyor maintenance, unexpectedly high labor costs for maintenance and cleanup, worker health and safety problems, and issues with community relations. As estimate attributed to the U.S. Mine Safety and Health Administration (MSHA) notes that 85 percent of conveyor maintenance is a result of fugitive material at conveyor transfer points. TECHNOLOGIES TO IMPROVE TRANSFER POINTS A number of techniques to improve the performance of conveyor transfer points have been developed. They include: • Absorbing impact, to prevent damage to belt, belt support systems, and conveyor structure, and reduce spillage caused by the impact energy arising from long material drops or large lumps of material loaded onto the receiving belt. • Stabilizing the belt line, to eliminate sag that allows spillage and encourages material entrapment that can damage the belt. • Protecting the skirtboard seals, by sheltering the sealing strips from the mass of cargo pushing material toward the edges of the belt. • Using self-adjusting, multiple-barrier edge seals, to keep material on the belt by providing long-lived seal efficiency with minimum maintenance requirements. • Controlling and centering the belt’s path, to eliminate belt wander and the spillage and damage it can cause. • Allowing dust to settle, through the incorporation of chutework that provides expanded stilling zone and the use of dust curtains at the points where the belt enters and exits the transfer. • Adding supplemental dust control systems, through the installation of systems for passive dust gathering, water-based dust suppression, and/or active dust collection."

Jan 1, 2017

By Albert G. Zima

THE conservation of strategic materials during war rime gives rise to many problems not commonly encountered in times of peace. During normal times, when world trade is unrestricted, we are apt to become lavish to a point of extravagance in our use of those materials which, during rime of war, become scarce owing to inadequate transportation and production facilities or because the enemy may be in position to control sources of supply. It becomes necessary, then, to enforce rationing of available sup-plies, and in some cases, where such supplies are wholly inadequate, we find we must resort to the use of substitute materials. We are now confronted with such a problem to an extent never before experienced, with the result that many of the commodities upon which our civilization depended are now either shut off completely or, because of the heavy demand occasioned by war production, are not available in sufficient quantities to meet requirements predicated on peace-time standards and manufacturing methods. It has become necessary, therefore, to make many changes, some of them very drastic indeed, to enable us to carry on our war effort effectively. This? discussion will deal briefly with one phase of this problem, namely, the conservation of alloys required in the making of steels necessary for war production. In line with a request from the War Production Board, the Technical Committee on Alloy Steels of the American Iron and Steel Institute made a study of experimental steels embodying the !east amount of alloying constituents, with the objective in mind of substituting these steels wherever possible for the standard alloy steels used heretofore. This study embraced the following phases: (1) The availability of silicon and manganese; (2) The average quantity of alloying elements recoverable from scrap; (3) The effect of increases in manganese and silicon contents on the general properties of steel; ( 4) The elements and ranges of elements which might be used to duplicate the hardenability of the steels now in use; (5) The effect of combining several elements in small quantities upon the properties of steel at various hardness and strength levels; (6) A determination as to whether or not the steels selected would suffice for general application. Working on this basis, the Committee arranged for the manufacture of several heats of steels containing various combinations of different amounts of such elements as silicon, manganese, chromium, nickel, and molybdenum. The steels thus produced were compared by hardenability tests.

Jan 1, 1943

By C. C. Birch

Due to grade estimation uncertainty, two statistical errors can occur. The Type I error is where material is classified as ore and mined, despite the true value being below the break-even grade. This material is dilution. The Type II error is where the material is estimated to be below the cut-off grade and is classified as waste, although the true grade is actually above the break-even grade. This material is not mined and is lost. The uncertainty was assumed to follow a normal distribution in a previous study. For this study, estimated block values are compared to those determined after mining (the best estimate of the true grade). This actual data from four mines shows that the uncertainty follows a Laplace. There is no single solution regarding adjusting the cut-off grade away from the break-even grade, considering estimation uncertainty, that could be applied to all gold mines. However, adjusting the cut-off grade downwards (up to 22% for one mine) is noted when optimizing the profit considering grade uncertainties. This type of adjustment could open up significant mining areas and extend the life of the mine.

Jul 2, 2022

By H. S. Price, F. N. Kissell, R. C. McCulloch, J. C. Edwards

"The methane em1ss10n from deep coalbeds which are actively mined is a serious problem facing the mining industry today. Pinpointing the source of methane and predicting the emission of this gas from these coalbeds is necessary if preventive techniques are to be effectively used to control methane emission. In general, because most coalbeds have water associated with them, the system to be studied may be either single-phase (methane gas) or two-phase (methane and water). Because coal mine geometry is complex and the fluids have variable properties as functions of pressure and methane concentration, the differential equations describing the flow of methane and water are not amenable to analytic solution, but must be solved numerically using high-speed computers. This paper presents the development of such a complex mathematical model along with some preliminary applications of the model to methane emission from one- and two-dimensional coalbeds with and without water present."

Jan 1, 1973

By Alexander S. Escalante, Luis R. Ramirez, Nelson A. Arostegui

Research, analyze, discuss, design, and build an electric oven to perform one of the quality control tests the fanel or common fulminers to determine what temperatures they can detonate at. Give practical applications, conclusions, recommendations and bibliography.

Feb 1, 2020

By ALBERT P. J. BORDEAUX

THIS paper briefly describes the general outline of cyaniding silver-ores in Mexico, with special reference to personal experiments made in the Temascaltepec district. The most important papers on the subject deal with cyaniding gold-silver-ores, the gold predominating in value, so that the treatment is nearly the same as for gold-ores, the losses of silver being considered of little importance. I describe here the treatment of silver-gold-ores containing very little gold, which is more general in Mexico than elsewhere. The cyanide treatment, which was so successfully applied to gold-ores, did not succeed immediately with silver-ores on account of their varying composition. Gold occurs in nature usually in the native state, while silver occurs generally in combination with sulphur (argentite), and various combinations of sulphur, antimony, and arsenic. In former times there was a complete difference in the treatment of gold-ores and silver-ores. Amalgamation, which was successful with gold-ores, was generally inadequate with silver-ores. The usual treatment in Mexico for silver was the patio process, the theory of which was satisfactorily explained only quite recently by Mr. Ortega and others. GENERAL OUTLINE OP THE CYANIDE TREATMENT. The general tendency of the present practice is to slime the silver-ore as much as possible, and in order to obtain a higher efficiency, with less loss of cyanide, and greater speed, the following lines are observed 1. Crushing by stamps with 30- or 40-mesh screens, then crushing by Huntington or Chilean mills, through 60- or 80-mesh screens. 2. Concentration upon vanners.

Jan 1, 1910

By Y. S. Roditis

A new method for interpolating a block model is proposed, where both the diamond drill holes (DHs) and blast holes (BHs) data are used. Combining these data types poses a geostatistical "class size" problem due to the different statistical properties of the densely populated BHs and the sparsely populated DH data. This paper discusses how linear regression was used to adjust the DH values prior to the interpolation to account for the "class size" problem which is inherent to the procedure. The correlation between the BHs and the DHs is found. The DHs are then corrected based on the regression line. Each block that falls within a certain range of influence of a blast hole is assigned a different code and is interpolated with the combined BH and regressed DH data set. Blocks that fall outside the range of blast hole influence are interpolated using the original DH data set. A comparison against other methods, indicate a 12% improvement over using DHs only and a 2% improvement over using BHs only.

Jan 1, 1992

By G. B. Walker

THE sink-float methods designated by heavy-media separation processes were pioneered by C. Erb Weunsch for the treatment of base metal ores as an improvement over jigs. The work of Weunsch was further developed by Victor Rakowsky and The American Zinc, Lead and Smelting Co. Early in the development of the processes, the inherent unsuitability of galena as the solid constituent of the medium was recognized and ferrous media amenable to magnetic recovery and control were developed. The high efficiency and low cost of magnetic recovery and cleaning of ferrous media regardless of particle size, slime contamination, or surfacial oxidation had led to the adoption of ferrous media by all of the sink-float plants operating under the heavy-media separation processes patents controlled by American Zinc, Lead and Smelting Co. Approximately 2,000,000 tons of base metal and nonmetallic minerals are treated each month by these methods.

Jan 1, 1949

By R. V. Ramani, S. Shankar

"The phenomenon of re-entrainment is seen in environments such as sand dune formation, soil erosion, fugitive dust emission and the spread of radionuclides from accidents involving nuclear weapons. A thorough review of existing literature reveals that work on re-entrainment of dust in mine atmospheres is scant. The present study was undertaken as a part of ongoing research at the Generic Mineral Technology Center on Respirable Dust at the Pennsylvania State University on the development of methods to predict ambient dust concentrations in mine atmospheres (Ramani, 1983). The contribution of re-entrainment to the spatial and temporal concentration of dust in mine airways is being studied. The research has included wind tunnel and in-mine studies.A set of seven experiments was performed under controlled conditions in the US Bureau of Mines' Lake Lynn Laboratory mine. Two types of source coal dust, anthracite and bituminous, were subjected to various airflow rates and were subjected to walking by two different individuals. Six sets of instruments were used along the test section for sampling airborne particles. The average air velocity just above the coal dust bed varied between 2.1 to 3.2 m/sec.Due to re-entrainment as a result of the airflow conditions, the average respirable dust concentration in the center of the mine airway increased to 0.09 mg!m3 (standard deviation= 0.03 mg/m3)from an initial value of 0.02 mg/m3. The concentration of all (total) airborne dust increased to 0.17 mg/m3 (standard deviation = 0.10 mg/m3) from an initial value of 0. 02 mg/m3. The action of people walking, however, caused higher amounts of re-entrainment. The average concentration of respirable and total dust at the center of the mine airway increased to values of 0. 28 mg/m3 (standard deviation of 0.12 mg/m3) and 1.53 mg/m3 (standard deviation of 1.0 mg/m3), from initial values of 0.03 and 0.05 mg/m3, respectively. Jr was observed that the dust concentrations were much higher near the floor, immediately at the end of the coal-dust bed.Depending on the level of activity and the amount of dust deposited in the mine airways, re-entrainment may become an important source of airborne dust in areas away from the point of actual mining."

Dec 1, 1996

By J. S. UNGER

A LARGE proportion of the coke used is made in the by-product oven from the high-volatile coals mined in the adjacent district. At the beginning it was feared good by-product blast-furnace coke could not be made with our coals. By experimenting with various mixtures of coals, coking time, oven design, and coking temperatures, much has already been accomplished. The results show that a hard, dense coke, not easily broken by handling, can be produced. In its present state it is not all that could be desired, but it is being constantly improved. Such coke has been used alone as the fuel on several of the blast furnaces producing the highest daily production in the Pittsburgh district. Many of the coals in the Pittsburgh district when coked in the by-product oven yield a gas which contains a high percentage of sulfur, which is objection- able for many metallurgical operations. As this fuel is gradually replacing the ideal fuel, natural gas, which is becoming less plentiful, studies are being made of the best methods for purification. Some metallurgists believe sulfur to be a very injurious element in steel. Recent investigations by Government bureaus, scientific bodies and private firms, seem to indicate that a reasonable amount of sulfur may exist in steel without detriment. Without wishing to provoke any metallurgical controversy on the subject of sulfur, the fact remains that the daily purification

Jan 1, 1926

By Pedro Jorge Walburga Keglevich de Buzin

Steel production process generates waste, among which is the electric arc furnace dust (EAFD). This waste has varying amounts of zinc, which is principally contained in the minerals zincite (ZnO) and franklinite (Fe2ZnO4). The presence of Zn is capable of economically motivating the recycling of this residue and facilitating the co-processing of the remaining material. The zinc content in EAFD and the presence of zincite, however, have significant influence on the application of hydrometallurgical recovery processes (economic alternatives to the Waelz process). In this study, based on the computational thermodynamic tool FactSage, theoretical considerations are made on the conditions for the formation of zinc-containing minerals found in EAFD. Through thermodynamic analysis, the best conditions for obtaining a high fraction of ZnO were analyzed, which favor the hydrometallurgical processes for EAFD treatment. A classification of dust depending on the phases present in the EAFD is suggested as a guide for the feasibility analysis for the use of a hydrometallurgical process.

Jul 30, 2018

By Henrik Saxén, Mikko Helle

The operation of hot stoves used for preheating the blast in the ironmaking blast furnace has a strong effect on the consumption of reductants, economic performance of and CO2 emissions from the steelmaking site. Generally, it is recommended to maintain as high blast temperature as possible, because this minimizes the rate of reductants in the blast furnace. The blast temperature is affected in a complex way by the time periods of heating and cooling of the stoves, and by the amount of gas combusted in the stoves. Furthermore, as the hot stoves show degraded performance with age, it is a non-trivial task to select optimal operation parameters for the stoves. The paper addresses this computationally by applying a one-dimensional heat-transfer model of the hot stoves for optimization of the performance of the system. The complexity and strong coupling of the decision variables is demonstrated by numerical examples, where the blast temperature is maximized under different constraints.

Jan 1, 2015

By Walter E. Mingramm

THE construction of rescue-apparatus on the principle of furnishing the wearer with air from a tank containing it under high pressure was given up by inventors about 20 years ago. Such an apparatus must supply continuously, for not less than two hours, nearly 50 liters of pure air at atmospheric pressure per minute, or a total of 6,000 liters (210 cu. ft.); and a cylinder containing this amount of air, under 2,000 lb. pressure, would weigh 180 lb. or more. Although apparatus has been recently constructed utilizing liquified air, no experiments have been made to determine the regularity with which the air is generated, nor has its chemical composition been determined. Moreover, the chief objection to such an apparatus is the' difficulty and cost of keeping on hand a large quantity of liquified air. The system of furnishing the wearer of a breathing-apparatus with air which has given the best results, and has found employment in all the devices now in practical use, is that in which the air contained in the human lungs at the beginning of the work is regenerated by the apparatus. By means of chemicals, such as caustic potash and caustic soda, the carbonic acid gas, CO., exhaled is absorbed, and the oxygen that has been consumed is replaced from a tank containing this gas under high pressure. The pressure of the oxygen (which is 1,875 lb. in the two cylinders at the beginning of the work) is automatically reduced to 75 lb., and is sufficient to keep the air inside of the apparatus in constant circulation, and to force it to pass through the chemicals provided for the absorption of the CO, gas. In the attempt to construct an apparatus which would (1) furnish the wearer with a sufficient supply of air; (2) replace the amount of oxygen used up by the lungs during the time of

Jan 7, 1908

By Forrest T. Moyer

The overall disabling work injury experience, excluding office- workers, at nometal mines and mills during the period 1961-63, as reported to the Bureau of Mines by operators, was 77 fatal and 7,201 nonfatal injuries during an aggregate worktime of 335,029,685 man- hours. These injuries, fatal and nonfatal combined, occurred at a frequency rate of 21.72 per million man-hours, comprising 0.23 for the fatal and 21.49 for the nonfatal injuries. The combined severity rate of the disabilities was 2,312 days lost or charged per million man-hours, consisting of 1,379 for the fatal and 933 of the nonfatal injuries, The average severity of all disabilities during 1961-63, was 106 days per injury, The number of days lost or charged, excluding officeworkers, at nonmetal mines and mills during 1961-63, was 462,000 days charged to fatal injuries and 312,461 days lost from nonfatal injuries. The outstanding causes for fatal injuries were explosions (18 fatalities occurred in a major mine-explosion disaster in a potash mine in Utah in 1963) and falls of rock or ore from back or side, while most nonfatal injuries were caused by handling materials, slips or falls of persons, haulage, and machinery. The parts of the body most frequently injured during the period 1961-63 were the trunk, hand and finger, and foot and toe, An average of 52,810 men were at work daily, There were 20 nonfatal disabling injuries reported for office- workers at nonmetal mines and mills during the period 1961-63 during an aggregate worktime of 23,088,496 man-hours, These injuries occur- red at a frequency rate of 0.87 per million man-hours, There were no fatal injuries reported.

Jan 1, 1967

By E. Westman

Geographic Information Systems (GIS) are becoming a more commonly used tool for resource estimation as they provide not only a database management platform, but also the graphical capabilities to visualize resource characteristics. Interpolation methods used commonly in these resource studies do not typically provide a quantitative answer to the question: "How accurate is the estimate?" By comparing localized measurements at several locations to the interpolated thickness distribution used in a resource estimate, a quantitative analysis of accuracy can be obtained. The technique is demonstrated with a case study from Central Appalachia.

Jan 1, 1999