Search Documents

By C. Özgen Karacan

Gamma ray, density, sonic and core logs obtained from two boreholes drilled over a longwall panel in Southwestern (SW) Pennsylvania were analyzed for formation boundaries, log-derived porosities and densities and for rock elastic properties from sonic transit times. Gamma ray (GR) and density logs (DL) were analyzed using univariate statistical techniques and fractal statistics for similarity and ordering of the log data in depth. A Fourier transformation with low-pass filter was used as a noise elimination (filtering) technique from the original logs. Filtered data was tested using basic univariate and fractal statistics, rescaled range (R/S) and power spectrum (PS) analysis to compare the information characteristics of the filtered logs with the original data. The randomness of log data in depth was analyzed for fractional Gaussian noise (fGn) or fractional Brownian motion (fBm) character. A new prediction technique using radial basis function (RBF) networks was developed to calculate shear and Young?s moduli of the formations when sonic logs are not available. For this approach, the filtered logs were used as input to an RBF based upon a combination of supervised and unsupervised learning. The network was trained and tested using rock elastic properties calculated from the sonic log of one of the boreholes. The network was used to predict the elastic and shear moduli of the coal-measure rocks over a longwall coal mine in SW Pennsylvania. This approach demonstrated that it could be used for prediction of elastic and shear moduli of coal-measure rocks with reasonable accuracy.

Jan 1, 2009

By S. J. Boone, A. Poschmann, C. Pound, A. Pace

San Diego’s Stadium Conglomerate consists of poorly cemented cobbles, gravel, sand, silt and clay. Conventional laboratory and in-situ testing is not suitable for characterizing its engineering properties. Although the formation is often considered a “rock” its behavior is more readily modeled using soil mechanics. Static and seismic design of a tunnel for the Mission Valley East light rail extension required that the stress-strain characteristics of the ground be identified over a broad strain range. Geophysical methods and field plate load testing were used to develop a full non-linear stress-strain model of the expected ground behavior. Quantification of the coarse material distribution was also required for selection of tunneling methods and construction considerations.

Jan 1, 2001

By Mark Kennedy, Allan MacRae, Cameron Hams

New technology projects, particularly those involving first-of-a-kind metallurgical facilities, have a poor track record of achieving their overall financial targets, as they incorporate technological risks in addition to normal project risks. Traditional project management tools focus on risk from concept development through implementation, but typically fail to address the additional risks associated with a new technology project including slow start-up, slow ramp-up, and failure to achieve design performance (quality or throughput). These additional risks affect future cash flows produced by the project and hence its value, typically measured as net present value (NPV) or internal rate of return (IRR). Common accounting practice is to reduce the present value of future cash flows by applying a chosen discount rate, often reflecting the corporation's cost of capital. This discount rate does not contain an allowance for technological risk, which is often underestimated or misunderstood by both the financial and engineering project managers. This paper will focus on the topic of project risk and new technology, and how these play a role in the probability of achieving the predicted future cash flows. By properly addressing technological risk in the form of risk-weighted returns, marginal projects can be prevented from proceeding, while sound projects can be given the additional time and resources required to achieve the optimal level of front-end-loading (the level which returns the maximum risk-weighted net present value). A simple set of mathematical tools should enable engineers and financial professionals to establish a common level of understanding, thereby leading to a more accurate assessment whether a new technology project is ready to pass through its next level of approvals.

Jan 1, 2011

By Karl J. C. Harries

"3.1. INTRODUCTIONThis chapter discusses briefly the common law concepts of fiduciary relationship, constructive trust, and breach of confidence. Following a discussion of confidentiality agreements, the last section of the chapter compares and comments on two common law cases, the LAC Case and the Metalore Case. Civil law readers should not ignore this chapter or § 3.5. the comparison as, to a large extent, the concepts and comments are universal, even though the procedures for applying them may vary.1It should be appreciated that, regardless of the legal system, if the Court sees that a wrong has been done, it will attempt to right that wrong, either by awarding monetary damages against the wrong-doer to compensate the injured party or by attempting to make the injured party whole again by such means as negating an agreement (as in the Metalore Case) or returning property to a wronged party (as in the LAC Case). The methodology for accomplishing either of these results will vary with the jurisdiction, and the two are not mutually exclusive.These two Ontario cases have been chosen, not because they are the only ones available – they certainly are not – but because both are relatively well known within the minerals industry and they deal with problems that may face any explorationist (although it is to be hoped that the facts of the Metalore Case do not represent “normal” behaviour). Each judgment offers useful guidelines, as well as insight into a judge’s approach to problems, the type of information he expects to receive, how his mind works, and, particularly in the Court of Appeal judgment in the Metalore Case, how he might reason through and “justify” his decisions.3.2. SOME LEGAL CONCEPTS In order to appreciate some of the matters discussed in this chapter, it is necessary to have some idea of the common law considerations of fiduciary relationships, constructive trust, and breach of confidence."

Jan 1, 2003

By David Pierce

The Port of Seattle, one of the largest on the west coast of North America, made a strong statement regarding their support for reusing existing structures when a decision was made to rehabilitate Pier 69, on Seattle's downtown waterfront, for their new headquarters. Because of its age and location, the pier provided an unusual challenge to the Port and its consultants. The Port hired Peratrovich, Nottingham, and Drage Inc. to design the seismic strengthening of the pier itself. To remedy the lack of seismic resistance in the 70-year-old pier, PN&D designed a new steel-pipe-pile supported concrete apron next to it. The structure relied on a development by PN&D, the "spin-fin pile", to achieve the tension capacities required of the batter piles. The construction of this apron was completed in October of 1991. Another team of consultants performed the superstructure renovation design, which is now under construction.

Jan 1, 1992

By Edgar Peek

"The two dominant metallurgical problems in treating most base metal sulphide concentrates in both the chloride and sulphate system are iron removal and sulphur elimination, respectively [1-3]. In this paper the opportunities, limitations and fundamentals of the chloride metallurgy system are described against this background. Only the treatment of oxide and sulphide ores is considered. Both hydrometallurgical and pyrometallurgical unit process operations are highlighted, since most successful base metal processes are based on a combination of the two. Hence, an overview of the technical and also some economical aspects of chloride metallurgy are presented.This overview summarizes the successful applications of chloride metallurgy, but it will not give exhaustive process and plant descriptions. It predominantly focuses on the essential technical features of the metallurgical unit process operations, while providing numerous references separately."

Jan 1, 2011

By Lloyd R. Nelson

The feasibility of producing low carbon (LC) ferromanganese (FeMn) by lime-'ore' melt refining of high-grade ferromanganese silicon (FeMnSi) was investigated. Thermodynamic simulations demonstrated significant benefits in moving from a single-stage ladle operation to a two-stage counter-current reladling operation (to emulate the commercial Penin Process). The theoretical alloy silicon content was predicted to be refined from 1.57 to 0.005 per cent silicon, at a 6.2 per cent higher manganese yield (yield predicted to increase from 82.3 to 88.5 per cent). Extension of this counter-current refining principle, to a multistage Counter-Current Reaction Launder (CCRL) was investigated using the Slag Metal And Gas Klnetics (SMAK) software to model the mass transfer kinetics of the multicomponent coupled reaction system. Simulation results suggested that commercial production of 50 000 tonnes per annum (tpa) of refined LC FeMn, containing less than 0.5 per cent silicon, at manganese yields of up to 90 per cent, should be feasible in a compact CCRL (7 m long by 0.7 m wide).

Jan 1, 1994

By E. T. Dumble

Introduction..........914 I. Topography,........915 The Nueces Basin........915 The Coastal Slope...........918 Streams..........919 II. Geology..........921 Eocene..........923 Basal Beds .......923 Lignitic Stage........923 Atascosa Sections......924 International and Great Northern Sections .. . 928 Leona Sections.......929 Nueces Sections....929 Rio Grande Sections.....930 Lower Claiborne Stage......932 Marine Beds ........933 Atascosa Sections....... 933 International and Great Northern Sections .. . 934 Frio County Sections,.....935 Rio Grande Sections.....936 Yegua Clays........938 Atascosa Sections......938 Tilden Sections.......941 International and Great Northern Sections .. . 942 Rio Grande Sections.....942 Fayette Sands........945 Atascosa Sections......946 Tilden Sections......948 Rio Grande Sections.....950 Frio Clays........953 Atascosa-Frio Sections.....953 Tilden-San Diego Sections....955 Rio Grande Sections......955 Neocene ....966 Oakville Beds.......957 Lapara Beds,....... 987 Nueces Sections......958 Bartlett's Ford Sections.....959 Fort Merrill Section......963 Lapara Sections,.....964 Tilden-San Diego Section.....967 Lee Tiendas.......969

Jan 1, 1903

By Sandy Worden

Coal mining companies in Australia are managing the high-consequence risks across their operations more effectively by using an interactive online risk management system known as Riskgate Developed by the Minerals Industry Safety and Health Centre (MISHC) at the University of Queensland, Australia, Riskgate contains detailed information about 11 high-consequence risk areas (called topics in the system) for opencut and underground coal mines (Table 1). The existing topics are: fires; strata control for underground mining; ground control for opencut mining; tires; isolation; collisions; explosions and explosives; manual tasks; and trips, slips and falls. Every Riskgate topic is focused on coal industry activities (mining, processing, transport and storage). The scope includes mine sites, lease areas and mine infrastructure (mobile, fixed plant, field equipment, buildings, road and rail transport), and all aspects of the mine life cycle from design through to decommissioning. The topics uniformly recognize that a loss of control can result in injury or fatality, equipment damage, production loss, reputation loss and environmental damage. However, the priority focus for Riskgate is the safety of mine personnel.

Jul 1, 2013

By Richard D. Miller

This Bureau of Mines publication contains analyses and related source data for 224 natural as samples from 18 States. Of the total, 191 sam¬ples were collected during calendar year 1981. The remaining 33 samples were collected during previous years, but releases, granting permission to publish were not received until 1981. All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by the mass spectrometer and special helium apparatus described previously (1-2).3 The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the general public. Twenty-five publications have presented the results of 12,827 gas analyses made prior to 1981. The first three bulletins (1-3) contain analyses and related data on 5,218 gas samples collected from 1917 through 1960; these bulletins have been supplemented annually by information circulars (4-17, 19-24) containing 7,609 analyses of samples collected since 1960.

Jan 1, 1982

By S. R. Clark

"INTRODUCTION Of all the natural resources being taxed by the needs of the modern world, perhaps the most important is the continually expanding demand for water resources. As water becomes scarcer, and increasingly important, new technologies are needed to find innovative ways to preserve this precious resource. In Chile, for example, the mining industry is investing billions of dollars to build desalination plants and pipelines; bringing ocean water as far as 200 kilometers inland to meet their demand and maintain operations. It is a full-blown crisis for that nation and a top priority for their government and economy. It has been reported that world water consumption will increase by 40 percent in the next 10 years, representing nearly exponential growth. In the U.S., as more and more communities continue to be built, more drain on the current water infrastructure is created. For 25 percent of people and operations that rely on water from aquifers, this source is being consumed at a rate that will create significant problems meeting the demand in as few as two generations.1 A PROACTIVE APPROACH When it comes to controlling dust at your operation, whether a landfill, a transfer station, a haul road or another ancillary area, what are the options? We know watering is not the answer, but at the same time, we need to prevent dust from flying to ensure a safe environment and keep our skies clear of pollution, for both regulatory requirements and neighbors. Creating a Dust Mitigation Program instead of looking to buy the first dust control product off the shelf is a first step to conserve water and, at the same time, maintain the operational demands and environmental standards for a given site. The program concept is straightforward enough. However, the process of effectively constructing and executing a program is quite involved. When undertaking a program, each manager needs to work with their team and their partners/vendors in analyzing the following elements: 1. Site Expectations—It is important to understand how to balance your internal standards with your regulatory requirements, as well as how to keep your neighbors satisfied. 2. Site Aggregate—Variations in native soil, such as clay content or gravel levels, greatly affect the approach that will yield the highest results. 3. Climate—Relative humidity and seasonal variations are critical to achieving predictable results through product choice, application frequency and timing. 4. Daily Traffic—The type and frequency of traffic is an essential variable for site management. 5. Environmental Responsibilities—If you have additional, specifically defined responsibilities, the approach to your site may vary. 6. Budget—While efficiency is the goal of any program, some sites will have more stringent restrictions than others. 7. Current Usage Rates—Document and understand where you’re starting from, both with water, supporting products, and maintenance so that effective measurement of results is possible."

Jan 1, 2018

This publication summarizes the Bureau's activities as part of a study of the Juneau Mining District (JMD) during the period 1984-1988. The objectives of the program were to identify the type, amount, and distribution of mineral deposits in the district, determine ore reserves, study beneficiation technologies for the ore, make feasibility studies, and address economic and legislative effects on mineral development. The JMD study was a cooperative study involving the Bureau and the Alaska Division of Geological and Geophysical Surveys (ADGGS). Over 30 employee-years were spent by the Bureau on this project. Bureau investigations in the JMD consisted of a district-wide investigation of industrial materials in addition to site-specific investigations of precious and base metals in five subareas. During the 4 years of the JMD study, more than 300 areas, mines, prospects, and occurrences were visited, which contain gold, silver, copper, zinc, lead, nickel, cobalt, tungsten, molybdenum, chromium, and platinum group metals (PGM). More than 59,000 feet of underground workings were mapped and sampled. More than 5,500 samples were taken; one diamond drilling program and three geophysical surveys were completed. An up-to-date and complete mineral data base for the JMD did not exist prior to this study. The JMD study, which coincided with a tremendous increase in mineral interest and activity in the district, has proven to be valuable to both the minerals industry and land management agencies. The discovery of two new mineral occurrences and compilation of data on known mines, prospects, and occurrences have aided industry activity in the region. The study enabled timely data to be available to land management agencies at the Federal, State, and municipal levels.

Jan 1, 2012

By H. von Blottnitz, B. E. Isheloke

Mining is a significant economic activity in most Southern African Development Community (SADC) countries, and mineral beneficiation has been identified, and controversially discussed as one of the possibilities for industrialisation. With many member countries being economically too small to muster the human and financial resources which beneficiation requires, the recently adopted Regional Mining Vision (RMV) envisages interventions at a regional level. An opportunity arose to ask industry role players to what extent the SADC appears to support regional beneficiation policy interventions undertaken by member countries, and what the challenges are in undertaking beneficiation regionally, as a complement to, or substitute for country-specific beneficiation policies. Twenty-five semistructured interviews were conducted with experts from SADC member countries during the 2019 Mining Indaba. Participants were divided on whether beneficiation should be carried out nationally or in the SADC region. While beneficiation could support value-keeping, key challenges were found to be infrastructure development (i.e. energy, water), scarce skills, access to technology and related costs, but also lack of free trade and movement. We submit that a more integrated beneficiation strategy for the SADC region, as is being developed through the RMV, would indeed be relevant in the future. Keywords: Mineral beneficiation, regional integration, beneficiation policy interventions, African mining vision, mining, SADC

Jan 1, 2020

By D. V. Hughes, J. R. Nyberg

"Since 1985, a comprehensive automation system has been installed at the Outokumpu Oy Zinc Plant, Kokkola, Finland. In leaching and solution purification special sample handling equipment, on-line analyzers and instruments, and a computer-based control system with duplicated supervisory stations have been installed. The system has enabled closer control of the process and more efficient use of labor. Since its installation recovery of zinc has improved, and use of zinc dust, steam, and water have decreased. The system has performed reliably. It includes optimizing programs and process study tools, which facilitate improving process performance. An expert system has been built-up to prompt process personnel to take appropriate action on the basis of process data. In electrolysis a similar system, based on extensive monitoring of the process and of production of zinc cathodes, is used to maximize- current efficiency by maintaining optimum conditions in the process. It is planned that in the future the control systems will be integrated and extended to cover the roasting plant and effluent control.IntroductionThe Zinc PlantThe Zinc Plant of Outokumpu Oy Metallurgical Division at Kokkola, on the West Coast of Finland, has grown from a 90,000 t/a plant founded in 1969 to become, with its present capacity of 170,000 t/a, one of the world's ten largest zinc plants. Especially since the completion in 1988 of a thorough modernization programme, it is also among the world's most modern.The Kokkola plant takes its raw materials from Outokumpu's own mines, Vihanti and Pyhasalmi in Finland, and Tara in Ireland, and from outside sources. Concentrates are roasted in two Lurgi fluid-bed furnaces, and the calcine is leached and iron removed by the Conversion process. Following this copper, cobalt, and cadmium are removed, and zinc is refined by electrowinning. The leaching and purification, and the cell-house are automated under computer-based control, and anode and cathode handling in the cell-house are mechanized and fully automatic."

Jan 1, 1989

By T. Imgrund, A. Bischoff, S. Spürk

"Specific conditions of underground coal mines at great depth, such as high temperatures, high rates of methane inflow and natural ventilation pressure provide considerable challenges for the reliable design of appropriate mine ventilation systems. For decades coal mining in Germany has coped with these extreme circumstances. Based on these experiences appropriate software tools for simulating mine ventilation networks have been developed and continuously enhanced. This paper examines differences in the simulation results and underlying calculation methods of two software solutions. The analysis is based on the comparison of FlowNetTM and VentSim DesignTM (Version 5.1) regarding the accurate prediction of fluid mechanical quantities and their validation with real measurements. A special focus lies on exceptional ventilation scenarios typical for deep coal mines, like gas inflows, fire events and buoyancy effects. The purpose of the comparison is the future utilization of the experiences gained during mining at up to 1,500 m depth for state of the art ventilation design. INTRODUCTION Ventilation is an essential component of mine operations—as providing fresh air to workplaces, diluting and removing explosive, toxic or asphyxiating pollutants and assuring sufficient climate conditions. On the other hand, the costs of ventilation contribute to a large extend to the overall operating costs of a mine, as the share in the energy consumption of a mine may be in the range of 25–50% (Belle, 2008). Accordingly, proper design of ventilation systems has been a task since early times. Consequently software for modelling of ventilation networks has been developed in order to improve efficiency and accuracy of calculations (Maleki, 2018). Compressible flow has not been considered by initial ventilation modelling software tools. In Germany, the consideration of changes in airflow density—depending on pressure and temperature—in the algorithms of ventilation simulation software has been started in 1974 by Duepre & Hofbauer. This development had been continued by the Pruefstelle fuer Grubenbewetterung (Test Centre for Mine Ventilation) and resulted in the release of a computer ventilation software named “Wetter”. The mine inspectorate of the German state of North Rhine-Westphalia, which supervises the major coal mining district in Germany, declared ventilation simulation based on compressible flow being “state of the art” in 1985 (Pollak, 1985). This pronouncement made allowance for assessing the consequences of underground fires and downtimes of main fans based on advanced software solutions."

Jan 1, 2019

By E. R. Mueller

The natural lives of machines and components vary tremendously! Maintenance managers struggle constantly to maximize their equipment lives while minimizing their maintenance costs, but they normally lack the tools and techniques they need to do this properly. This paper proposes a methodology based on probabilities of failure and expected values for repairs that recognizes the variation among individual machines and components as well as the high costs associated with catastrophic failures. It enables a user to determine the optimum change-out intervals for many types of equipment. The approach proposed here is sophisticated enough to be reliable but simple enough to be applied by the maintenance staff on the shop floor. It will complement existing preventive and predictive maintenance programs.

Jan 1, 1995

By J. P. Gouvea, W. Geel

Resin bolting in South Africa has been developed and refined in underground coal mines (i.e., soft rock) since the late 1940s. The extension of resin bolting to hard rock mines started in 2003 and has required significant adaptations, challenging the status quo from both a supplier and applicator perspective. As far as resin bolting is concerned, the most affected aspect in coal mining and hard rock mining environments, is the rock drills or machinery used for installation. Hard rock mines mostly use hand-held airlegs with limited thrust, low torque, and rotation speed, relative to coal mine mechanised bolters. Resin bolt development for hard rock mines was, and still is today, predominantly focussed on compensating for the ‘shortfalls’ of using hand-held airlegs. At face value, hydro-powered rock drills, which are more powerful than traditional handheld equipment, provided hard rock mines with a means to attain more consistent and reliable resin bolt installations. This paper assesses the quality and performance of hydro-powered resin bolting at an intermediate to deep level platinum mine in South Africa and its potential contribution to rock-related instabilities when applied erroneously. The findings of this paper necessitate a revision of current quality control and quality assurance measures related to resin bolting for underground support.

Nov 24, 2025

By Hirsch H. H.

The paper, presented at the North of England Institute of Mining Engineers' general meeting held in Newcastle-upon-Tyne on 12th February 1916, gives a short description of the Hirsch lamp, which, though largely used in the United States of America, has not yet been adopted in Great Britain. The lamps, which consist of (1) the watchman's lamp and (2) the miner's lamp, are portable, and have been designed to provide a safe and reliable light for use by watchmen, and in mines, rescue-work, powder-works, oil-refineries, and other places where special precautions become necessary on account of the presence of explosive materials or gases. The lamps are in each in­stance operated by a storage-battery contained within a casing, and this supplies the current necessary for a miniature incandescent lamp. Each safety-lamp forms a complete unit and can be carried from place to place or held in any position. Appendices give details of battery cleaning, test results and safety reports

Dec 1, 1916

By Richard E. Ray

Conventional concrete block plastered with a cemantitious coating is the most common material used in the construction of perma¬nent stoppings to direct airflow in underground mines in the U.S.A. All mines experience various degrees of strata convergence depending upon depth of overburden, geological conditions, and type of roof support employed. Strata convergence will cause cracks and joint openings in masonry stoppings, resulting in significant air leakage losses. Where strata convergence is severe, complete structural failure of the stopping can ultimately occur. Reconstruction of damaged or destroyed stoppings adds expensive overhead to mining operations, and even greater expenses are incurred from the additional fan horsepower required to overcome leakage losses. Ideally, a stopping should maintain high resistance to airflow while yielding to strata convergence. By properly incorporating "Max-Seal" polyisocyanurate rigid foam material within the masonry block structure, stopping service life can be increased several-fold in mines experiencing strata convergence problems such as floor heave, roof loading, and lateral rib movement.

Jan 1, 1984

By E Thomas, L McCallum, G Dale, J Bennett, K Reardon-Smith, S Raine

Sustainable closure of coal mines in Australia to a safe, stable, non-polluting condition remains one of the industry’s biggest environmental and social challenges. A significant proportion of mines in the Bowen Basin of Queensland have dispersive spoil. Based on an estimated area of 20,000ha and a rehabilitation cost of AUD$100,000 to AUD$150,000/ha, the instantaneous rehabilitation liability for the Bowen Basin alone is estimated at AUD$2 to $3 billion.Dispersive spoils present problems in post-mining rehabilitated landforms due to increased potential for surface and tunnel erosion, compromising the ability to achieve fundamental mine closure objectives of a safe, stable, non-polluting and self-sustaining post-mining landform (Minserve, 2004). Dispersion results in clay particles being mobilised and transported in water, even at low flow velocities (So et al., 1998; Minserve, 2004), and blocking of soil pores, resulting in surface sealing, crusting and reduced permeability (DNR, 1997; Vacher et al., 2004) which, in turn, further increases runoff (Dang et al., 2018).CITATION:Dale, G, Reardon-Smith, K, Thomas, E, Bennett, J, McCallum, L and Raine, S, 2018. A process-based approach to mine rehabilitation decision making using Bayesian modelling and risk-based principles for dispersive spoil rehabilitation, in Proceedings Life-of-Mine 2018, pp 106–109 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018