Search Documents

By F. R. Archibald

SINCE the opening of the Beattie mine, in 1933, the concentrate produced by flotation has been considered refractory. As the gold extraction by cyanidation was poor, the concentrate, during the first four and a half years of operation, was shipped to a smelter for further treatment. After the installation of the cyanide plant, in 1934, seventy per cent of the gold in the concentrate was recovered before shipment to the smelter. In 1937, a roasting plant was built so that treatment might be complete at the mine. Much experimental work had been done by a number of investigators prior to the installation of the roasters, but none of them had seriously attempted to identify the causes of, or the elements responsible for, the refractory behaviour of the concentrate. Intensive investigation in this direction commenced in the Beattie lab-oratory in July, 1938, has led not only to the identification of several causes contributory to the refractory behaviour, but also to revisions in procedure and principles with respect to roasting Beattie concentrate in particular and arsenical concentrates in general. The accuracy of the identification of these causes and the soundness of the principles is borne out by interpretation of roasting plant records, by improvements and simplification since applied. to plant operation, and also by laboratory and test-plant results on arsenical concentrate produced by another mine. It is the purpose here to present an account and interpretation of the laboratory investigation, together with a correlation of laboratory and plant results. Incomplete extraction of the gold by cyanidation after roasting is due primarily to the nature of the material roasted, and secondarily to the manner in which it has been roasted. There is a possibility that better extraction may be obtained by improvements in both particulars.

Jan 1, 1939

By Adil Jamali, Taufiq Hidayat, Imam Santoso, Zulfiadi Zulhan, Indah Suryani

The study investigates the segregation of iron and titanium in iron sand concentrate pellets reduced using coal under an isothermal-temperature gradient profile. The results show that metallic iron migrates to the surface while titanium and other oxides move to the center of the pellet. The study provides insights into the reduction process and the behavior of iron and titanium during heat treatment.

Mar 2, 2022

By John Cogan

INTRODUCTION Lake tapping is a method of blasting an intake into a body of water from below the natural water surface without first lowering that surface or installing a protective cofferdam around the tap hole. Lake taps are done by first excavating a tunnel almost to the water/rock contact and then blasting out the final protective rock plug at one time to allow water to suddenly inflow into the tunnel from the lake. This procedure can be done "dry" or "wet." In the dry method the tunnel is empty of water before the final plug blast while in the wet method it is partially filled with water. This paper describes a wet method lake tap as performed at Alaska Power Authority's Tyee Lake Hydroeletric Project in southeast Alaska. The Tyee Lake project is located approximately 40 miles southeast of Wrangell, Alaska, in a glacially formed valley called the Bradfield Canal. The project consists of a powerhouse located at sea level on the canal, a system of tunnels and shafts connecting the powerhouse to Tyee Lake at elevation 373 m (1225 ft), and an 129 km (80-mile) electrical transmission line leading from the powerhouse to Wrangell and then Petersburg, Alaska. Tyee Lake itself is a natural lake gouged out of the rock by glacial ice during the last ice age. The objective of the project was to tap into the lake and use the water as a source for power production. The techniques used for lake taps have been developed in Norway where conditions are favorable for their use in hydroelectric proj¬ects. Over 100 have been performed. In the United States the Tyee

Jan 1, 1984

By Walter R. Storms, Jerry W. FAUST

This paper, which describes mining methods and costs at the Kearney zinc-lead mine, is one of a series being prepared by the Mining Division of the Bureau of Mines on mining practices, methods, and costs in varicus mining districts of the United States. The Kearney mine, which is owned by the New Mexico Consolidated Mining Co., a subsidiary of the Peru Mining Co. (Illinois Zinc), is situated a few miles southeast of the town of Hanover, in the northwest corner of sec. 27, T. 17 S., R. 12 W., in the Central Mining District, Grant County, N. Mex. (Figs. 1 and 2.) This report presents a brief history of the district, describes the geology, and outlines methods of prospecting and exploration, including eampling and estimation of tonnages and values. Development and mining methods are explained, and transportation, ventilation, drainage, safety measures, and organizatich are described. The wage scale and mining costs comprise the concluding sections of the report.

Jun 1, 1949

By Kirk Ellison, Eric S. Lindquist, Peter Faust, Stephen M. McLandrich

"The 181 Fremont Tower will be an 800-foot high-rise with a 60-foot deep basement located in a dense urban part of downtown San Francisco. The design and construction methods of the subsurface elements navigated a variety of site constraints such as loose fill and soft estuarine soils, shallow groundwater, contaminants, historic obstructions, small work area, proximity of adjacent buildings, and the on-going excavation and build-out of the adjacent Transbay Transit Center (TTC) train box. Design of the approximately 260-foot-deep drilled shafts (some of the deepest foundations ever constructed in San Francisco) was proven by a full-scale load test that provided unique data on the frictional capacity of the deep soil and Franciscan Complex bedrock in the region. Design and construction of the shoring system for the 5-story basement excavation was exceptionally challenging because of the on-going construction for the TTC. To allow for flexibility during construction, hydraulic rams were placed in a transfer waler along the shared TTC shoring wall that could adjust the forces transferred through to the TTC excavation if required. Open and steady communication between the shoring engineer, the geotechnical engineer, and the shoring/foundation contractor was crucial in order to satisfy the complex constraints of this site.INTRODUCTIONThe 181 Fremont Tower is a new build mixed-use tower, currently under construction in the dense urban core of the South of Market District of San Francisco, California. This high-rise will consist of 54 above ground floors with the roof level 700 feet high. Atop the roof will be some architectural features including a spire that will top out at just over 800 feet, which will make it the second tallest building in San Francisco upon completion.The tower is being developed by Jay Paul Company and the architectural design is by Heller Manus. The structural engineer and geotechnical engineer for the project is Arup North America Ltd (Arup). The shoring designer is Brierley Associates (Brierley). The general contractor is Level 10 Construction (Level 10) and the specialty foundation contractor and excavation contractor is Malcolm Drilling Co., Inc (Malcolm)."

Jan 1, 2017

By Venancio Astucuri

"El presente texto describe las cuatro competencias que debe poseer un ingenierio de minas para un desarrollo sostenible de la minería. Dichas competencias se dividen en personales, académicas, profesionales y de ingeniería. Este grupo de competencias pueden ser usados también para un proceso de autoevaluación, donde cada uno pueda medir sus competencias con el fin de determinar brechas y superarlas, de forma que las empresas puedan plantear requisitos mínimos para sus diferentes posiciones laborales y, finalmente, para que en las instituciones educativas, estos puedan diseñar de forma adecuada sus respectivos planes de estudio."

Feb 1, 2017

By K. Mayhew, K. Murray

The CESL Copper Process was developed as a hydrometallurgical alternative to smelting and refining for copper sulphide concentrates. As the majority of such concentrates contain appreciable gold and silver values, effective recovery of these metals is essential to the economics of this technology. Unfortunately, conventional cyanide processing cannot be used on the residue from the copper process, clue to its unusual characteristics when compared with naturally occurring gold and silver ores. An abundance of elemental sulphur, as well as the presence of cyanide soluble copper, leads to the formation of both thiocyanate and copper cyanide which is detrimental to process economics clue to excessive cyanide consumption. This, however, can be reduced to acceptable levels by process innovations such as pressure cyanidation and cyanide recovery. This paper outlines the successful application of the CESL Gold Process to various gold-bearing copper concentrates from bench to demonstration scale.

Jan 1, 2011

By J. L. Eakin

A method was developed by the Bureau of Mines in the laboratory and in the field to relieve capillary waterblocks in gas wells. Impaired gas permeability was improved by this inexpensive chemical treatment which lowers the surface tension of the water held in the capillaries of the formation. Effectiveness of the alcohol-surfactant treatment was tested with a variety of chemicals and with sandstone cores cut from rocks having relatively low permeability. Field tests on 20 gas-producing and storage wells demonstrated the effectiveness and limitations of the method. The productive capacity of some wells was doubled by the treatment. The final test was evaluated by the neutron logging technique for measuring changes in apparent liquid saturation. Maximum apparent liquid saturation was reduced by 52 percent; gas production rate increased from 2.3 to 3.5 MMcfd (million cubic feet per day).

Jan 1, 1965

By J. A. Theron

"This paper provides guidelines on performing mass and energy balance modelling involving coal and coal derivatives. Usually, the inputs to a pyrometallurgical process would be specified in terms of elements and compounds. Reliable thermochemical data is more widely available for species involving uniquely defined, relatively smaller molecules. However, in the case of coal, the molecules are extremely large and not uniquely defined. Consequently, modelling processes involving coal and its derivatives involve several potential pitfalls. These are outlined in the present paper.It was found that coal proximate analysis should not be regarded as absolute; it could vary with several parameters, including heating rate. For modelling, the use of ultimate analyses should be considered a preferable option to proximate analyses, where ‘fixed carbon’ and ‘volatiles’ are not defined in terms of chemical composition. Significant errors could be incurred if the larger molecules are neglected during calculation of the calorific value (CV) of coal gas (the gas liberated when coal is heated in the absence of oxygen).For elemental analysis determination, the oxygen content (which is calculated by balance) should be checked to ensure it is within the expected range. For representation of sulphur in coal, one should avoid doublecounting due to SO3 in the ash analysis.Potentially, oxygen in coal could be represented as O2, H2O, CO, or CO2.However, use of some of these species without considering the experimentally determined gross CV leads to significant errors in the energy balance. If coal enthalpy is calculated from elemental analyses without correction, representation of coal oxygen as H2O(l) gives reasonable accuracy. Coal volatiles could be represented by a complex mixture of compounds, even using different oxygen-containing species than these four, provided the enthalpy is corrected.It is recommended that an ‘enthalpy correction value’ be incorporated in energy balances involving combustion, devolatilization, or conversion of coal and coal derivatives, e.g. coke, char, or tar. That would imply that proximate analysis, elemental analysis, as well as the gross CV would be required for all solid or liquid coal-derived substances being modelled. No other correction due to carbon being present in a form other than graphite should be used, as that would imply double-counting some effects."

Jan 1, 2015

By M. H. Basiri

Crude oil, as a central commercial commodity, is tied to major economic activities in all nations. Also its price fluctuation plays a significant role in global political and economic situation, as a change in the price invariably affects the cost of other goods and services. Therefore reliable forecasts of the price of oil are interest for a wide range of applications. Several approaches have been proposed over the past few years. These may divide into three categories; artificial intelligent, statistical techniques and hybrid methods. The neuro-fuzzy is one of the sub divisions of hybrid method, containing neural network and fuzzy techniques. In this paper a novel forecasting model based on adaptive neuro-fuzzy inference (ANFIS) is proposed to predict monthly crude oil price. To be able to train and test the model, the statistical data from 1990 to 2010, was obtained from West Texas Intermediate oil prices. The results are compared with a multi criteria regression analysis, it is demonstrated that the neuro-fuzzy lead an accurate and more promising forecast.

Jan 1, 2012

PT Freeport's Mine in Irian Jaya, Indonesia uses a number of 500m long vertical ore passes to transfer ore from the open pit to the mill. The current tonnages moved are in the order of 125 ktpd and this will be increasing to 240 ktpd. This amount of falling rock generates high pressures in the ore bins, when ore feed is terminated the pressure is no longer constrained resulting in back blasting of materials and air up the ore passes. Three methods were tested to try and eliminate or reduce this problem; recirculation of the entrained air, widening of the orepasses and relieving the pressure of the back blast. The final method proved to be the most effective in the short term. As a long term solution the orepasses are currently undergoing widening.

Jan 1, 1998

By Leon W. Dupuy

Many articles have been written describing peculiar and particular types of drilling. Little correlation has been made between the character of ground to be drilled and sampled and the type of drilling most desirable for procuring satisfactory samples. In development work, the engineer and metallurgist often desire the recovery of a sample in as physically natural a condition as possible, particularly when the sample must provide material for process tests as well as chemical and physical analyses. This paper describes the results of experimentation in drilling unconsolidated materials carrying titanium minerals in the Magnet Cove area, Ark. The drilling was most difficult in that the ground varied much in consistency, and it was vitally necessary to recover a physically natural sample. Ordinary churn drilling recovered a sample that could be analyzed chemically, but the sample was not in its natural state. The problem was successfully solved by utilizing and further developing methods used in the oil and clay industries.

Jan 1, 1949

By G. Shaw

IN recent years, most of the reconnaissance work of the Geological Survey of Canada has been mapped on a scale of 1 inch to 4 miles. Topographic base maps, commonly made from aerial photographs, were available to the geologist for such work. The advent of war curtailed aerial photography for civilian purposes, and by 1941 all areas already photographed had been geologically mapped. Nevertheless, the need for geological maps to assist post-war prospecting was so apparent, and the country to be covered is so vast, that some new method of rapid mapping had to be devised. It was felt that the need would be met if geological maps could be produced at a scale of 1 inch to 8 miles, provided they were sufficiently accurate in topographic detail to serve as guides to travel. Though in such maps there would be considerable sacrifice of geological detail, they would serve to outline, at least approximately, the major geological units, some of which might prove of sufficient interest to warrant later detailed study. It seemed that such mapping would be particularly useful in the northern regions of Canada which the work of early explorers has indicated are underlain largely by granitic rocks. These, so far as is known, are barren of mineral deposits, but within them are known to be areas or bands of 'greenstones' of the type that, in some localities, have been found to contain valuable orebodies. The problem, then, was to devise a method of mapping, particularly of such greenstone bands, that would make it possible to cover a relatively large area-say 30,000 square miles-in one season and at a cost below that of 4-mile mapping, with, of course, some sacrifice of accuracy. The problem seemed to be threefold: (a) to observe as much of the bed-rock as possible; (b) to produce a topographical map of as much of the area as possible, with particular reference to portions of geological interest; and (c) to cover as large an area as possible in a limited time, which meant faster modes of travel than have hitherto been used. The obvious answer to all three phases of the problem was the use of aircraft. If rock types could be broadly differentiated from the air, reconnaissance traverses by air would supply the answer to the first part of the problem. For topography, air photographs taken on reconnaissance flights appeared to be the answer. For the third phase of the problem, the use of aircraft was ideal.

Jan 1, 1943

By Todd M. Ruff

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are studying methods to prevent workers from being entangled in machinery used at mining operations. An analysis of mining accidents in the United States that resulted in a fatality or permanent disability from 2000 through 2005 showed 438 severe incidents that involved contact with machinery or equipment, an average of 73 per year. Researchers determined that the most common machinery involved in these severe accidents was conveyors. Also, a significant portion of the accidents occurred during machine maintenance and repair. Researchers are focusing on improved methods to prevent unintentional machine startup during maintenance activity and methods to detect workers near moving machine components. One new technology that shows promise for this application is intelligent video. Popular in the surveillance and security industries, these systems use cameras and computerized video analysis techniques to automatically detect the presence of people in preset zones within the camera?s field of view. A preliminary study has been initiated to determine if this technology could reliably detect the presence of workers in hazardous locations near machinery. Possible advantages of the use of this technology include improved detection zone demarcation and improved ability to distinguish between hazardous and non-hazardous proximity, compared to conventional proximity sensor techniques. Initial tests to detect a person near a conveyor system in daylight conditions showed promising results. A description of the technology, test procedures and results, implementation challenges, and future research needs are discussed.

Jan 1, 2008

By Henry S. Burnholz, Charles Y. Clayton, Francis B. Foley

This work was first undertaken for the U. S. Bureau of Mines, in 1919-20, by C. E. Julihn, superintendent of the station at Minneapolis. Learning of the interest, in this subject, of B. F. Tillson, of the New Jersey Zinc Co., Mr. Julihn and Mr. Foley went to Franklin, N. J., and discussed the matter with him. A conference in Chicago, in November, 1920, was attended by Dr. F. G. Cottrell, who was then Director of the Bureau of Mines, and representatives of the Bureau of Mines and of the hlissouri School of Mines and Metallurgy; at this time a cooperative plan of work was agreed upon by the Bureau of Mines and the Missouri School of Mines. In February, 1921, Mr. 'Tillson arranged a conference on this subject at the time of the annual meeting of the American Institute of Mining and Metallurgical Engineers, at which several technical papers were presented. In a paper, the Breakage and Heat Treatment of Hock Drill Stcels, he suggested a program that might be carried out in connection with the investigation of the problem. At this conference Mr. Manning, former Director of the Bureau of Mines, suggested the formation of an advisory committee to the Bureaus of Mines and of Standards for prosecution of this investigation. On Feb. 20, 1922, a secoud conference in New York, at the time of the annual meeting of the American Institute of mlining and Metallurgical Engineers, was attended by representatives of various technical societies. At this meeting, the report of Nov. 20, 1921, of the Chiefs of Divisions of Metallurgy of the Bureaus of Mines and of Standards, was discussed and it was agreed: 1. That the survey recommended by the two bureaus should be undertaken, which survey would have for its object the ascertaining of the present status of the practice of the heat treatment of drill steels, the extent to which the breakage occurs, etc.; and 2. That a report should be presented, of the findings of those who made the survey, to the Advisory Board to the Bureaus of Mines and of Standards. The Bureau of Standards assigned $4000 to the prosecution 01 a three-months' survey, which was carried out in April, May, and June, 1922, of about sixty mines

Jan 1, 1923

By Charles Y. Clayton, Henry S. Burnholz, Francis B. Foley

This work was first undertaken for the U. S. Bureau of Mines, in 1919-20, by C. E. Julihn, superintendent of the station at Minneapolis. Learning of the interest, in this subject, of B. F. Tillson, of the New Jersey Zinc Co., Mr. Julihn and Mr. Foley went to Franklin, N. J., and discussed the matter with him. A conference in Chicago, in November, 1920, was attended by Dr. F. G. Cottrell, who was then Director of the Bureau of Mines, and representatives of the Bureau of Mines and of the hlissouri School of Mines and Metallurgy; at this time a cooperative plan of work was agreed upon by the Bureau of Mines and the Missouri School of Mines. In February, 1921, Mr. 'Tillson arranged a conference on this subject at the time of the annual meeting of the American Institute of Mining and Metallurgical Engineers, at which several technical papers were presented. In a paper, the Breakage and Heat Treatment of Hock Drill Stcels, he suggested a program that might be carried out in connection with the investigation of the problem. At this conference Mr. Manning, former Director of the Bureau of Mines, suggested the formation of an advisory committee to the Bureaus of Mines and of Standards for prosecution of this investigation. On Feb. 20, 1922, a secoud conference in New York, at the time of the annual meeting of the American Institute of mlining and Metallurgical Engineers, was attended by representatives of various technical societies. At this meeting, the report of Nov. 20, 1921, of the Chiefs of Divisions of Metallurgy of the Bureaus of Mines and of Standards, was discussed and it was agreed: 1. That the survey recommended by the two bureaus should be undertaken, which survey would have for its object the ascertaining of the present status of the practice of the heat treatment of drill steels, the extent to which the breakage occurs, etc.; and 2. That a report should be presented, of the findings of those who made the survey, to the Advisory Board to the Bureaus of Mines and of Standards. The Bureau of Standards assigned $4000 to the prosecution 01 a three-months' survey, which was carried out in April, May, and June, 1922, of about sixty mines

Jan 1, 1923

By Jorge A. Benitez Muro

Within the exploration programs carried on by the Consejo de Recursos Naturales No Renovables, the one with the largest coverage (more than 75, 000 square kilometers) is the northern Coahuila Exploration Project. Due to its nature, geochemical exploration methods were selected to obtain quick results. The program included essentially, three main stages : 1. - A regional geochemical stream sediment survey. 2. - Semi-detailed studies of the anomalous areas selected in the previous stage, and 3. - Detailed exploration of the promising areas. To the date, the first two stages have been completed, and the third one is being carried on. The work was started on september 1972, and it will probably take one more year before drilling can be started, but at the end of stage three it is expected that at least 5 important targets will have been detected. The regional work was conducted by 3 field crews, but the detailed program is being done by only one.

Jan 1, 1974

By S J. Schafrik, Z Agioutantis, E C. Jong, K Luxbacher

Real-time monitoring of mine operating parameters is available at most mines. However, access to these data for an individual operation is typically underutilised by mine managers and technical personnel. Such monitoring systems are typically designed to provide data streams and alarms to a responsible person, but they are not utilised to extract underlying trends or correlate different data groups. Furthermore, multiple monitoring systems are usually implemented at a given site without interconnection between vendors’ systems or connection to any central management, and mine personnel are only exposed to a minimal subset of such data. Thus, it is not easy to analyse and correlate individual data streams and generate information to enhance day-to-day operational decision-making and improve safety and efficiency.This paper addresses the primary challenges associated with centralising data management and effecting greater utilisation of the vast amount of collected data, while at the same time reducing the time and effort required to manage such large data sets. Furthermore, it presents the conceptual design of a database application that can organise, present and analyse data collected by multiple sensors in different environments. The database is designed to operate in a passive manner so that active mine data management systems are not impacted. An example is given where this database is used for managing atmospheric data collected at an underground coalmine operation in the US. These techniques have a universal application and can be incorporated in a wide range of mining and construction projects.CITATION:Agioutantis, Z, Schafrik, S J, Jong, E C, Luxbacher, K and Karmis, M, 2015. A platform for managing and analysing atmospheric data in underground coalmines, in Proceedings Third International Future Mining Conference, pp 3–10 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By Stefan Medel

As a pioneer Herrenknecht started in 2018 to automate the production of tunnel lining segments. Since then, many automation processes became state of the art. Robots cleaning and oiling the moulds, hydraulic units opening and closing them fully independently. Artificial Intelligence (AI) controls the works and ensures the quality requirements. Data management has become a massive tool from a simple data collector towards a control and optimization tool. Sensors controlling concrete maturity and supporting the precast team to optimize the concrete mix. These state of the art and new innovations will be presented in this paper.

Jun 23, 2024

By R. B. Lawrie

Diesel powered underground mining equipment is presently the most productive, safest and efficient equipment used in underground mining operations. The widespread application of this equipment to underground mining is restricted, however, largely because of the difficulty of controlling the diesel engine exhaust emissions. This paper briefly examines control devices currently available for underground application, and also discusses the theory and mechanics of controlling diesel missions with particulate traps and filters.

Jan 1, 1985