Search Documents

By W. G. Schultz

"Sylvite's potash mine, which produces 8,000 tons of ore per day, probably ranks as one of the most highly mechanized and automated mining operations in the world. Employing, on a normal 10-hour production shift, one supervisor and a crew of seven operators, Sylvite is able to mine at an average rate in excess of 600 tons per hour. The ore is produced by two Marietta miners weighing 258 tons, the largest and heaviest pieces of equipment ever taken underground. The ore produced by these two Marietta miners is conveyed to the shaft area, cycled through a 15,000-ton storage system and hoisted to surface completely automatically. The operation of all equipment in the mine can be monitored and controlled from a central control panel located underground. Because Sylvite's mine is a new operation with equipment of a new design, the full potential of the operation has not yet been realized. The ultimate capability is clearly evident from the success Sylvite has had over the past year as the average mining capability has risen from 100 tons per hour to 600 tons per hour."

Jan 1, 1973

By Richard P. Rothwell

THOUGH coal has been mined in this country for more than a century, no systematic effort was ever successfully made to ascertain the total amount produced. The production of the Cumberland Basin, Md., and the shipments from the anthracite fields of Pennsylvania, have been placed upon record, thanks to the intelligence sand foresight of Mr. C. Slack in the former case, and to the late Mr. B. Bannan in the latter. For some of the years between 1822 and 1842, the production of the Richmond Basin was reported by Mr. R. C. Taylor, but since that date till the author undertook this work it was impossible to obtain any statement of the production of this field. A few of the newer fields, such as that of Mt. Diablo, Cal., have been fully reported, and a few of the newer States have also had this service performed by some intelligent private individuals.; but no statistics of coal production have ever been collected either by the State or General Government, if we except the returns for the years 1869-70 of the census report. During the year 1875, by great exertions, I succeeded in obtaining, and July 3d, 1875, gave in the Engineering and Mining Journal what, "though not an accurate statement of our coal production," was " by far the most full and reliable that had ever been published." Though that report showed the production of bituminous coal to be 23,630,094 gross tons, or about six million tons more than had ever before been reported, it was in reality two and a half million tons below the actual output. The more full returns I obtained for 1875 gave many figures for 1874

Jan 1, 1877

By M. M. Tilman

The objectives of this research were to determine the practicability of using cobalt as a means of controlling the amount of ferrite in the micro-structures of semiaustenitic stainless steels, and to determine the effects of reduced ferrite content on mechanical properties of these steels. Cobalt additions of up to 3 weight-percent were made to type 17-7 PH2 (AISI 631) stainless steel. Ferrite contents were determined for alloys in the aged condition, and for alloys quenched from the hot working temperature. Ferrite can be completely eliminated from the microstructure of 17-7 PH stainless steel by additions of cobalt, but complete elimination of the ferrite phase results in lower tensile strength, yield strength, and hardness. Tensile properties, hardness, and impact strength were determined for aged material. A subzero temperature treatment before heattreating was necessary to obtain maximum strength in the alloys containing cobalt. Addition of 2 weight-percent cobalt enhances mechanical properties of 17-7 PH stainless steel.

Jan 1, 1968

By Ernest J. Stocking

ENGINEERS are the key men in our war program today. Upon the technical knowledge and skill of the engineer and upon his administrative and executive abilities rests the entire success for the production of vital materials of the war. Naturally the work load of the engineering examining unit of the U. S. Civil Service Commission has increased greatly since our active participation in the war. At present, over 550 separate requests for certification of eligibles are received by the engineering unit per week. These represent more than a fourth of the total requests received for personnel by the Commission's central office at Washington and represent a recruitment work load of three to four times that carried by the whole Commission previous to January 1940. These requests represent a minimum of a thousand vacancies to be filled each week, while an average week will produce, at present, approximately 1400 vacancies and a weekly maximum may approach well over 2000 vacancies.

Jan 1, 1942

By C P. Gravenor

In 1953, a deposit of sedimentary oolitic iron ore was discovered in the Clear Hills area of northwestern Alberta. Since that time, detailed drilling has outlined reserves in excess of 200 million tons of ore grading 30 to 35 per cent iron. Attempts to physically beneficiate the ore to meet blast furnace or direct reduction feed specifications have been, in general, unsuccessful. In 1960, Premier Steel Mills Limited and the Research Council of Alberta jointly sponsored a pilot-plant test at the R-N Corporation at Birmingham, Alabama. About 5,000 tons of ore were treated, and briquettes containing 90 per cent Fe were produced, with 83 per cent recovery. At the same time that the R-N tests were being made, the Research Council initiated a program to produce high-purity powders by chemical methods. Several purification techniques were investigated; hydrochloric acid dissolution of reduced ore was finally adopted. Briefly, the steps involved in this acid process are as follow

Jan 1, 1964

By Robert E. Barieau

General expressions for evaluating practically all the thermodynamic properties of a fluid from a single equation of state are derived. Most of the formulas are expressed in terms of the compressibility factor, with this factor being an explicit function of the temperature and the molal density. Similar expressions are given using reduced variables.

Jan 1, 1967

By J. N. Hartley

Uranium mill tailings, waste products of uranium extraction, contain hazardous constituents that if released into the atmosphere and groundwater could threaten our health and environment. To provide for safe disposal and control of these tailings, Congress enacted the Uranium Mill Tailings Radiation Control Act of 1978 (Public Law 95-604). Subsequently, the Environmental Protection Agency (EPA) established standards for tailings disposal that limit radon emission into the air to 20 pCi m-2s-1 on an annual average basis (EPA 1983). The design life of the impoundment is to be 1000 years where practicable, but 200 years at least. To facilitate the design of containment systems that will meet the EPA standards, the Nuclear Regulatory Commission (NRC) and the Department of Energy (DOE) are sponsoring research at the Pacific Northwest Laboratory (PNL)* to develop the necessary technology. Earthen and asphalt materials have been evaluated for use as radon barriers (Hartley 1983) and as liners to minimize leaching (Buelt 1983). Herbicide and rock barriers against biological intrusion have been evaluated (Cline 1982). Surface stabilization techniques have been investigated to maintain the long-term effectiveness of a containment system that must be protected from wind and water erosion, chemical and physical degradation, and biological disturbance.

Jan 1, 1984

By Artur R. P. Junior Sergio, Pedro A. Netto, N. Monteiro, Foluke S. de Assis, Frederico M. Margem

Synthetic fibers are being replaced gradually by natural materials such as lignocellulosic fibers. Compared to synthetic fibers, natural fibers have shown advantages in technical aspects such as environmental and economic. So there is a growing international interest in the use of those fibers. The banana fiber presents significant properties to be studied, but until now few thermal properties on banana fiber as reinforcement of polyester matrix were performed. The present work had as its objective to investigate, by photoacoustic spectroscopy and photothermal techniques the thermal properties of diffusivity, specific heat capacity and conductivity for polyester composites reinforced with banana fibers. In the polyester matrix will be added up to 30% in volume of continuous and aligned banana fibers. These values show that the incorporation of banana fibers in the polyester matrix changes its thermal properties.

Jan 1, 2015

By J. Szekely, Robert G. Lee

Calculations are presented for the prediction of the combined radiative-convective heat loss from molten steel held in a ladle, covered by initially molten slag. A mathematical formulation is given and numerical solutions are presented of the resultant partial differential equation. It is shown that a slag layer of about 2 to 3 in. thick would prevent any significant heat loss from the top metal surface for Periods of up to 1 hr. For thinner slag layers (or in the absence of the protective slag) appreciable heat losses would occur; plots given in the paper allow the quantitative evaluation of the fall in the metal temperature due to this heat loss. The ironmaking-steel processing operation involves several intermediate steps where the molten metal is held or transfered in ladles. The quantitative assessment of the heat losses occurring under these conditions is of considerable importance in process design considerations since the temperature of the metal may have to meet rigid specifications in any given part of the processing sequence. While the metal is held in a ladle, heat is lost by two mechanisms: i) by conduction into the ladle walls; ii) by radiation and convection from the top surface. Calculations relating to the conductive heat loss, are readily made and information may be found in the literature both on data pertaining to metallurgical situations and on the techniques that are available for performing additional computations.'-3 The evaluation of the combined convective-radiative heat loss is less straightforward, especially when there exists a protective slag layer covering the metal. In this latter case, as the top slag surface loses heat partial solidification may occur and the latent heat thus given up by the slag may represent an effective barrier to the heat loss from the metal. A semiquantitative assessment of the role played by the slag in preventing heat loss from the metal has been made in a previous paper,4 where it was shown that a slag layer 6 in. thick would act as a near-perfect insulator for periods of up to 2 hr. However, this first paper reported on an essentially preliminary investigation that considered only one slag layer thickness; furthermore, the boundary conditions used for the calculations were somewhat restrictive since no allowance was made for changes in the metal temperature. The purpose of this second paper is to extend the scope of the preliminary investigation previously reported by: i) considering several slag layer thicknesses; ii) allowing for variations in the metal temperature; and finally iii) by performing calculations on the net loss from the metal rather than from the slag surface. FORMULATION Consider a slag phase extending from y = 0 to y = L1, covering a metal phase that occupies the region extending from y = Ll to y = L, as illustrated in Fig. 1. Denote the slag and metal temperatures by TS and Tm and assume that initially both slag and metal are molten, having a uniform temperature Ti. At time = zero the surface represented by the y = 0 plane (top slag surface) is brought into contact with cold air, the temperature of which is given as T Thus for time > zero, heat will be transfered from the slag to the air by natural convection and thermal radiation; as a result of this heat loss the slag temperature will fall and after some time a solid phase is formed and a solidification boundary (more realistically described as a zone) will move progressively from y = 0 toward y = L1. Once the region of temperature gradients, moving ahead of the solidification zone, reach the slag-metal interface (y = L1) there will be a net transfer of heat from the metal through the slag to the cold air, across the y = 0 plane. In the formulation of moving boundary problems, involving phase changes that require computer solution, it is convenient to represent both phases by a single equation, making allowance for the latent heat of solidification by assigning an appropriate temperature dependence to the specific heat content. Thus the energy equation for the whole of the slag may be written as follows:

Jan 1, 1969

By C. M. Davidson

Contamination of by-product: sulfuric acid, by dissolved oxides of nitrogen ('nitrates') occurs under some operating conditions encountered in sulfide roasting and smelting,, notably when oxygen-enriched air is used. This 'nitrate' lowers the value of the acid and increases the effective cost of smelter gas desulfurization. The present paper describes measures taken at one smelter acid plant to remove this 'nitrate'; it discusses the mechanism by which 'nitrates' in some cases concentrate in one part of the plant and can be purged for more efficient treatment; and it describes a process developed by C-I-L Inc. for removal of 'nitrates' from such a purge stream. Advantages of the process include very low reagent cost, recovery of all sulfuric acid values and safe handling of nitrous fumes.

Jan 1, 1983

By T. G. Joseph

ABSTRACT: The Canadian oil sands provide some of the harshest mining conditions in the world. Asoperations demand ever bigger tools, the toll on large mobile mining equipment is high, with structural life often half of that expected. Soft ground conditions predominantly lead to fatigue failure scenarios, poor stability, and inconsistent payload evaluations. These challenges are not solely a concern for Canadian oil sands mines; there are far-reaching implications for surface mining equipment in any poor ground-operating environment. This paper focuses on the basics of payload evaluation, motion response, and a simple estimate of structural life for haulers.

Jan 1, 2011

By H. L. Riley

This report describes the methods and equipment used by the Watauga Stone Co. to drill und blast limestone in a two-level quarry, and to crush, screen, blend, and load this stone. Power requirements per ton of stone produced are reported. The personnel requirements for individual phases of the operation are tabulated in man-hours per ton of stone produced.

Jan 1, 1963

By H. L. Riley

This report describes the methods and equipment used by the Watauga Stone Co. to drill and blast limestone in a two-level quarry, and to crush, screen, blend, and load this stone. Power requirements per ton of stone produced are reported. The personnel requirements for individual phases of the operation are tabulated in man-hours per ton of stone produced.

Jan 1, 1963

By T. L. Joseph, G. Bitsianes

THE layered structure of partially reduced iron ore was described in a previous paper.' Reduction by hydrogen was found to take place at well-defined interfaces between layers of the solid phases. In the present investigation, a detailed study was made of the wiistite phase that had formed during the partial reduction of a cylindrical compact of chemically pure hematite. An unusually wide band of wiistite permitted a rather detailed study of this phase. The specimen was made from Baker's C.P. hematite in the form of a cylinder 1.5 cm in diameter and 1.8 cm long. A dense ore structure with about 6 pct porosity was attained by heating the specimen in air at 1100°C for 3 hr. To confine reduction to the top surface, a ceramic coating was applied to the bottom and sides of the cylindrical compact. The specimen was then partially reduced in hydrogen at 850°C and subjected to a coordinated sequence of macro-, micro-, and X-ray examinations. A section of the partially reduced cylinder is shown in the macrograph, Fig. 1. Four layers consisting of metallic iron, wustite, magnetite, and unreduced hematite are clearly shown. The effort to force reduction to proceed downward in topochemi-cal fashion was only partly successful, as some reduction occurred along one side and bottom of the cylinder. A rather wide layer of dark wustite phase had formed, however, and permitted sampling for X-ray studies as indicated. To supplement previous work and to study the wustite layer in more detail, ten separate layers were removed for X-ray examination. Broad and diffuse patterns were obtained with the as-filed powders, especially with those of iron and wiistite, and the condition indicated a cold-working and variable composition effect within the respective layers. This condition was corrected by annealing the entire series of powders at an appropriate temperature. For the annealing treatment, the ten powder samples were wrapped in silver foil, sealed under vacuum in small quartz tubes, and heated at 750°C for 16 hr. The specimens were then drastically quenched in cold water to preserve the annealed condition. These annealed specimens were X-rayed in turn and the compiled patterns are shown in Fig. 2. The standard patterns for iron and its oxides have been interjected at appropriate positions for purposes of comparison and phase identification. All of the patterns obtained were clearcut and concise so that positive identifications could be made for all of the phases. The outermost layers A, B, and C were composed almost entirely of iron with a small amount of wiistite being detectable at the X-ray limit of phase detection. Layer D from the iron-wustite interface showed both of these phases. The next four layers E, F, G, and H were all in the dark phase band which had been tentatively identified as wustite by the macroexamination, Fig. 1. The diffraction data with their single-phase patterns of wiistite for these layers checked the visual evidence. Continuing the X-ray analyses after layer H, the macrograph (Fig. 1) shows that layer I came largely from the magnetite zone but included some fringes of the wiistite-magnetite interface. The diffraction pattern for the sample confirmed this observation. Layer J came from the unreduced core of the specimen and its diffraction pattern indicated a preponderance of hematite phase. The reduction behavior of synthetic compacts has thus been found to be similar to natural dense iron ore. The previous results were supplemented with measurements of the diffraction films and calculations of the respective unit parameters. These X-ray data are summarized in Table I and offer some interesting correlations as to the compositions of the various phases undergoing reduction. The iron layers that were analyzed gave lattice parameters close to that of pure iron at 2.8664A. Evidently this iron was present in layers A through D as a pure phase with little or no oxygen dissolved in its lattice. With the wiistite layers an entirely different situation prevailed in that there was a definite and

Jan 1, 1955

By M. J. Gilbey

London Underground is the oldest and one of the deepest Metros in the world. The temperature of the Underground has been increasing over the last 100 years, mainly as a consequence of increases in train service. Further increases in train service are planned in the coming years to meet the predicted growth in passenger demand. Unabated, the additional service will increase temperatures on the Underground. London Underground Limited (LUL) has therefore set up the Cooling the Tube Programme (CTP) to tackle the issues of thermal conditions on the Underground. Some of LUL?s studies and cooling methods have borrowed experience and techniques from the mining industry; some of methods used or proposed may in turn be of interest to the mining community. This paper presents a background into the sources of heat on the Underground network, the manner in which the heat is presently dissipated, the analysis of future temperatures and criterion and a number of means and methods being used or proposed to cool the network in an environmentally sensitive manner.

Jan 1, 2009

By Mark Kruzynski, Srinivas Garimella, James T. Wiswall

"A flue gas recirculation (FGR) system for a combustion fired aluminum melting furnace is experimentally investigated. The FGR system flows combustion air in a turbulent jet within the flue gas stream, and the turbulent jet flow is collected in a tube at a distance from the jet exit. Entrainment of the flue gases as well as heat transfer between the flue gases and the jet occurs over the length of the exposed jet. Heat transfer between the flue gases and the jet, and the amount of flue gas entrained into the jet (derived from temperature, flow rate and oxygen fraction measurements) were measured as a function of nozzle exit velocity and the distance between the nozzle exit and collection tube. In addition to flue gas entrainment, a fuel savings of up to 7%, due to heat transfer over the length of the jet, was projected from the measurements obtained.IntroductionFlue gas recirculation can be applied to aluminum melting furnaces to control combustion temperature. When coupled with a device to improve furnace efficiency by recovering heat from the furnace exhaust, flue gas recirculation provides a control technique that is integral to achieving the goals of reducing fuel consumption, increasing product yield, increasing the longevity of infrastructure, and reducing pollutant emissions. In particular, combustion temperature control can help reduce reactivity of the products of combustion with the molten metal surface and furnace refractory materials. Combustion temperature control can also help improve the life of heat exchangers used to recover energy lost to the environment in the flue gases, and reduce NOx formation in the combustion process. Flue gas recirculation can also dilute oxygen used in oxy-fuel combustion to reduce reactivity.Flue gas recirculation has been used since the 1970s to control flame temperatures in the automotive industry [1-3] and has successfully reduced NOx emissions. Many different flue gas recirculation approaches for high temperature melting such as melting aluminum and glass have been patented since the 1980s [4-12]. There has also been academic interest to determine the fundamental performance characteristics of flue gas recirculation in high temperature furnaces and in combustion [13-15]."

Jan 1, 2014

By Thomas P. Oxford

The impact of recent legislation on Florida phosphate industry operations has been dramatic. The most significant influences are described: the National Environmental Policy Act of 1969; the Federal Water Pollution Control Act Amendments of 1972; and implementation of the Florida Environmental Land and Water Management Act of 1972. Further discussion includes: critical examination of the recently completed EPA Areawide EIS; potential effects of the Resource Conservation and Recovery Act of 1976; the Surface Mining Control and Reclamation Act of 1977; current local and state laws; and summary of studies on radiochemical effects of mining, seepage from gypsum ponds, and dewatering of waste clays.

Jan 1, 1979

By Hwa-Soo Park, J. K. Yoon, Hoseok Nam

In a thin slab casting process, control of fluid flow in mold is particularly difficult due to the high casting speed and large aspect ratio of the mold and the understanding of the fluid flow motion as well as heat transfer in mold is regarded as the most important information because the melt delivery is directly related to the problems of shell growth nonuniformity, surface turbulence and mold powder entrapment. A mathematical model has been developed for the coupled analysis of fluid flow, heat transfer and solidification in funnel type mold using finite volume method based on a body fitted coordinate and the characteristics of the transport phenomena in the mold of thin slab caster were analyzed by numerical simulation. As a result of simulation, the basic flow pattern is characterized as four large recirculations and two small eddies near the narrow faces of mold, which is somewhat different from that of parallel type mold or other conventional slab caster. The heat transfer model accurately predicted the mold positions susceptible to cracking as a result of thermal stress and the predicted shell thickness shows good agreements with the measured shell thickness on breakout products. We also investigated the influences of some operation parameters such as casting speed, nozzle type, submerging depth and mold material on fluid flow, heat transfer and distribution of solidifying shell and various information for the determination of optimal operating conditions were obtained.

Jan 1, 2000

By Jiongtian Liu, Jianjun Wu, Yongzhou Wan, Li Feng

"Mechanical Thermal Expression (MTE) is a developing non-evaporative lignite dewatering technology. It has been shown to effectively dewater high moisture content in low rank coals via the application of mechanical force and thermal energy at elevated temperatures. In this paper, the dewatering behavior of Yunnan Xiaolongtang lignite during the MTE-process was studied. Furthermore, how variations in temperature and pressure during the MTE process affect the surface oxygen functional groups and pore structure were also discussed using Fourier transform infrared spectrometer (FTIR) and mercury intrusion porosimetry (MIP). Increases in MTE temperature and pressure resulted in significant reductions in residual moisture content and moisture holding capacity, along with the increase of fixed carbon content and reductions of other elements content, especially oxygen content, which have been largely attributed to the destruction of the surface oxygen functional groups and porosity in lignite. The optimized technology conditions are temperature 150~220°C and pressure 7~10MPa. The residual moisture content of the lignite treated by MTE under the conditions of 200°C and 10MPa is decreased to 8%, while the dewatering rate exceeds 76 % and the calorific value approaches 22 MJ/kg. The experimental results offer a deeper understanding of the influence of process parameters on the lignite stuctures and properties. The reduction in residual moisture content, surface oxygen functional groups and pore volume under increasingly severe MTE conditions are suggestive of the structure changes that accompany increased coalification (rank) within the lignitic range."

Jan 1, 2014

By Thomas A. Wheeler

The reagents commercially used in coal flotation and their roles are reviewed and discussed According to their function the reagents are divided into often overlapping groups: 1. Collectors 2. Frothers 3. Conditioning Reagents Frothers have by far the largest effect on the amount of coal recovered They act not only in their traditionally accepted function of “bubble makers”, but in coal flotation they serve in a seldom acknowledged role of collectors. A lab flotation study on four samples of different coal ranks shows how these react to various frother families and proves that no froher is the optimum reagent for all types of coal. The advent of new technology in flotation equipment in the past decade has resulted in various novel designs of column cells, Jameson and Centrifloat™ cells, air-sped hydrocylones, etc. All should require special frothers or blends of frothers to meet their specific needs.

Jan 1, 1994