Search Documents

By O. C. Blade

"INTRODUCTION This report on the properties of aviation gasolines and aviation jet fuels produced in the United States during 1952 was mode under a co¬operative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior.Analytical data are presented for 94 samples of aviation gasoline which include for the first time in this series of reports, data on five samples of grade 108/135 aviation fuel. Data also are given for 34 samples of aviation jet fuel. The analyses were made on samples typical of the manufacturers' production in their laboratories and the results sub¬mitted to the Bureau of Mines for compilation. The products of 20 manufacturers of aviation gasolines and of 16 producers of aviation jet fuels are represented.SUMMARYA comparison of certain properties of the commercial aviation gasolines produced in the United States during 1950, 1951, and 1952 is presented in table 1, the 1952 data being average values from tables 3 through 7 of the present report. Trends in certain characteristics of these fuels may be seen in figures 1 through 5 which also indicate the minimum and maximum values. As may be observed, the properties of commercial aviation gasolines have not varied greatly during recent years. A list of aviation-fuel survey reports published by the Bureau of Mines is given on page 7.Table 2 presents a summary of data from table 8 and compares properties of aviation jet fuels of 1952 with summarized data on jet fuels of October 1951."

May 1, 1953

By Daniel Hodouin

Artificial neural networks (ANN) are of growing interest in a wide variety of applications. Pattern recognition, speech processing, financial analysis, signal processing and process control are at present the most successful ones. This paper is an attempt to illustrate the potentiality of ANN applied to mineral processing. An introduction to the technology of ANN is first proposed to describe the various components and to explain the various phases encountered in setting up a network. Then examples are given to illustrate the use of ANN dynamic modelling of mineral processing units or plants and in process control.

Jan 1, 1991

By Dale L. Pitt

Introduction In opening up a new country, one of the most vital problems is that of transportation Without roads, railways, or water routes, development is very slow because these are the arteries through which the life-blood of the country flows. British Columbia is unusually fortunate in having along its western coast, for some 600 miles, a stretch of inside water unequalled, for comfortable and safe navigation, by any other similar stretch of ocean in the world. This solves in a general way the major north and south transportation problem for the coast section, and offers comparatively cheap rates for the shipping of all commodities. The principal cities and centres of distribution will naturally grow up on the coast. These cities, however, must have methods of communication with the hinterland, and it is the necessity of supplying these, as feeders to the principal ports, which presents problems of considerable magnitude.

Jan 1, 1930

By David De Lemos Pires

Mining is essentially a materials management process where materials are classified, excavated, moved to a desired location, processed at a cost and sold for a price hopefully to generate a profit. ?How much is that cost and can it be reduced?? is the age-old question. The requirement for a paradigm shift with regard to materials movement in search of low-cost production has not just happened by chance but, rather, has been driven by agents of change that include mining companies, consultants, governments and equipment suppliers. During the past 100 years of mining, surface mining technology has involved humans with hand tools, humans with machinery and unmanned automated equipment. In the past 50 years, surface mining technology has evolved and now takes the form of trucks and loaders (TL), in-pit-crushing conveying (IPCC) and autonomous haulage equipment (AHS).

Dec 1, 2013

By Chen Chen, Wang Yanze, Hong Xin

Furnace superalloy was applied in harsh environment within the erosion of high temperature and oxidizing atmosphere. With plasma powder surfacing technology, iron-based alloy powder was sprayed on the surface of 310S stainless steel to form oxidation layer that increases the oxidation resistance and reduces the cost of materials. With optimum technological parameters, in this paper, oxidation test of 100 hours on iron-based cladding alloy and furnace alloy were carried out at 1200 . The technique of XRF, XRD and EDS were used to characterize composition, oxide morphologies and surface mechanical properties. The results showed that Element composition of cladding layer formed by Plasma powder surfacing was well distributed. Its oxidation weight gain rate of 100 hours was 0.4552g/m2h, belonged to antioxidant level. The oxidation weight gain rate of furnace alloy was 1.4617g/m2h, belonged time-antioxidant level. And on the mechanical comparison test, surfacing alloy is relatively excellent than furnace alloy.

Jan 1, 2016

By Andrzej Luszczkiewicz, Magdalena Duchnowska, KGHM Polska Miedz S. A., Witold Pawlos, Jan Drzymala, Alicja Bakalarz, Przemyslaw B. Kowalczuk

A pre-flotation process of the Kupferschiefer ore with only frothers produces a concentrate enriched in carbonaceous matter and tailings for further upgrading steps. A partial removal of easy-to-float components of the feed before the main enrichments steps by flotation (rougher, scavenger) improves overall efficiency of separation of valuable elements from the ore. Since the types and doses of frother used for pre-flotation effect the process, the aim of this study was to determine the influence of selected frothers on the efficiency and selectivity of the Kupferschiefer ore processed by KGHM Polska Miedz S.A. A series of pre-flotation tests in the presence of different poly(propylene glycols) ethers, poly(ethylene glycols) ethers and aliphatic alcohols were conducted. The obtained results indicated that the types and doses of frother determine the flotation selectivity of copper and total organic carbon. The evaluation of the pre-flotation process was based on the analysis of selectivity parameters calculated from the recoveryrecovery Fuerstenau upgrading curves as well as the values of copper and organic carbon grades in the flotation products. It was shown that pre-flotation performed in the laboratory scale using a suitable frother provides higher overall flotation selectivity of organic carbon with lower overall flotation recovery of copper in comparison to flotation without the pre-flotation step. Thus, the pre-flotation process improves the quality and quantity of the final concentrates produced from the Kupferschiefer ore.

Jan 1, 2016

By E. Watkins, S. J. Schatzel, V. Gangrade, R. Kimutis, J. Addis, C. Hollerich

The recent shale gas revolution in the United States has led to the drilling of hundreds of unconventional shale gas wells in active and future coal reserves in traditional coal-mining regions of Pennsylvania, West Virginia, and Ohio. This paper summarizes the impact of a shale gas well breach on the mine ventilation system of an operating longwall panel. This study utilizes a 1:30 scaled Longwall Instrumented Aerodynamic Model (LIAM) to simulate a single-panel longwall operation. The LIAM will be utilized to identify flow pathways and distribution patterns of gas from breached gas well scenarios in an operating longwall in the Pittsburgh Coal Seam. Sulfur hexafluoride (SF6) tracer gas is utilized to simulate a breached gas well. Preliminary findings suggest that the breached gas is diluted to regulatory levels and does not accumulate in the mine entries or in the longwall gob when the longwall panel is adequately ventilated. Overall, this study characterizes the potential interaction between shale gas wells and the mine environment in the event of a gas well breach, which provides critical information to the industry and regulatory agencies for improving safety, health, and welfare of miners.

Mar 2, 2022

By C. G. Bieber, J. R. Mihalisin, R. T. Grant

A growing demand for longer service life of gas turbines has placed increasingly rigorous requiret~rents upon superalloys employed for that application. Long-titne testing at high temperature has revealed that phase transformations occur in all superalloys. A common one of particular interest is o formation. Presented here are studies made to identify a and to characterize its formation and effect on properties in three cast nickel-base superalloys—IN 100 alloy, alloy 713C, and alloy 713LC. Methods are discussed by which o can be eliminated or inhibited in IN 100 alloy and alloy 713C. Evidence was obtained to indicate that some types of o may be more detrimental than others. Limitations in the electron vacancy approach to o prevention are pointed out, and it is shown how alternative approaches, such as reducing a complex superalloy matrix to the form of a pseudo-ternary system permitting equilibrium diagram treatment, lead to additional insights into the formation of in these alloys. AROUND 1960. Beiber1 developed IN 100 alloy, which still remains one of the strongest commercially available nickel-base superalloys. The principle used in the design of this alloy was to produce large quantities of y' phase in a y matrix through the use of copious amounts of aluminum and titanium. In 1963, ROSS' showed that when certain heats of this alloy were held for a long time at 1650°F they formed an acicular phase, subsequently identified as a.3 a is a hard and brittle phase first discovered in the Fe-Cr system by Bain and Griffiths.4 They termed it the "B" constituent. Subsequently this same phase was found in other systems, primarily those of the transition elements, and acquired the name "a" by which it is now known. The crystal structure of the a phase was first determined in the Fe-Cr system in 1950.5 It was shown to be tetragonal with a c/a ratio of about 0.52. as is the case with a found in other systems. This characteristic crystal structure is now the means by which a is identified. In superalloys, such as IN 100 alloy. large amounts of o impair the high-temperature creep strength and drastically reduce room-temperature tensile ductility. Discovery of o phase in some heats of IN 100 alloy quickly led to investigations of other superalloys for similar transformations. It was found that many of the stronger, more highly alloyed. super-alloys were indeed susceptible to o formation. This investigation has been concentrated on three commercial alloys: IN 100 alloy, alloy 713C, and alloy 713LC. J.R.MIHALISIN,MemberAIME, and C.G.BIEBER are with The International Nickel Co., Inc., Paul D. Merica Research Laboratory, Sterling Forest, Suffern, N. Y. R. T. GRANT, Member AIME, is with The International Nickel Co., Inc., Pittsburgh, Pa. Manuscript submitted May 22. 1968. IMD A detailed study has been made of the phase transformations and their relation to a formation along with a consideration of electron vacancy approaches for predicting a-forming propensity in these alloys. EXPERIMENTAL PROCEDURE Phase transformations were studied by light and electron microscopy, electron diffraction, microprobe investigations, and X-ray diffraction. Specimens for light micrographic examination were prepared by conventional grinding and polishing followed by etching with glyceregia (2:l HC1/HNO3 + 3 glycerine by volume). Photomicrographs of stress-rupture specimens were taken adjacent to the fracture unless otherwise noted in the text. Negative replicas for electron microscopy were taken from surfaces electropolished with a solution of 15 pct H2SO4 in methanol. For carbon extraction replication, a solution of 10 pct HC1 in methanol was used. A Siemens Elmiskop I was used for all electron microscopy. Selected-area diffraction studies were made at 80 kv using evaporated aluminum for standardizing the patterns. A nondispersive electron microprobe attachment was used to analyze the extracted precipitates chemically. The fluorescent X-rays were recorded using a flow counter containing P10 gas (90 pct Ar-10 pct methane) with a beryllium window and a single-channel pulse-height analyzer. The pulses from the analyzer were passed to a scaler-ratemeter and differential curves of counting rate vs pulse amplitude were obtained. The base line of the analyzer was driven with a synchronous motor at 0.5 v per min and a channel width of 0.5 v. The time for 105 counts was printed out for each 0.5-v increment. The microscope was operated at 80 kv with beam currents of 1 to 20 pa. This equipment detects elements from atomic number 13 to 40. X-ray diffraction studies were usually made on residues electrolytically extracted in 10 pct HC1 in H2O, although in one case a pattern was obtained from an etched surface of a metallographic specimen. A Siemens Crystalloflex IV was used with iron-filtered CoKa radiation. X-ray patterns were recorded using a goniometer speed of : deg per min. The scintillation counter and pulse-height analyzer operated at a channel height of 10 v and a channel width of 12 v. The equipment was calibrated with a powdered gold standard. The residues usually contained a number of phases. several of which could not be found in the ASTM card file. In addition, as is shown for the case of a phase in IN 100 alloy, other phases had a somewhat different lattice parameter from that reported in the ASTM card file, making it difficult to separate and identify constituents by comparison with ASTM d spacings. For these reasons, phases were identified on the basis of the lattice parameter obtained by indexing the ob-

Jan 1, 1969

By Joseph D. Lessard

A process simulation of the conversion of molybdenum disulfide concentrates into molybdenum dioxide via the Looping Sulfide Oxidation process has been performed using HSC 7.1 thermodynamic software. By decoupling molybdenite conversion and molybdenum oxidation, Looping Sulfide Oxidation changes the paradigm by turning molybdenite processing into an energy generator while producing a molybdenum dioxide, which has a lower vapor pressure and lower oxygen content than molybdenum trioxide. The Looping Sulfide Oxidation process selectively produces molybdenum dioxide over molybdenum trioxide. This process uses a stoichiometric mixture of oxygen and molybdenum trioxide as oxidants in the conversion of the molybdenum sulfide to the molybdenum oxide. The model simulates the two reactor scheme required by Looping Sulfide Oxidation and incorporates thermodynamic equilibrium simulations performed in FactSage 6.3.1 thermodynamic software. Energy capture is also maximized with heat exchanger systems to transfer heat released in reactions to preheat air.

Jan 1, 2014

By R. J. Roman

The results of column leaching tests on 3 different mixed oxide/sulfide ores from a Chilean deposit are presented. The 3 samples contained different ratios of oxide copper minerals to chalcocite and chalcopyrite. The results of the column leach tests are interpreted in light of the shrinking core model for coarse particle leaching. The copper recovery from the oxide minerals and the sulfide minerals each conforms to the shrinking core model with the total recovery equal to the weighted average of the individual minerals. The use of column test results to predict field heap leaching results using the multi-mineral shrinking core model is discussed.

Jan 1, 1993

By R. R. Sayers

TWO serious hazards from coal dust confront the bituminous-coal miner- -a physical or safety hazard and a physiological or health hazard. The first threatens the miner with loss of life from coal-dint explosions, and the second with loss of health and earning capacity from inhaling large quantities of the dust. Studies by the Bureau of Mines have shown that coal dust, except some grades of anthracite dust, is capable of initiating an explosion when no explosive gas is present and that its property of extending or propagating an explosion has been responsible for nearly all the widespread explosions that have occurred in bituminous mines in the United States in the present century. For years many mining people believed that low-volatile coal dust was not explosive but not only is it explosive but if the source of ignition is intense, it is as explosive as the dust of many high-volatile coals because the war is creating increased pressure for greater coal production and because of the trend toward greater mechanization in mines, explosion and health hazards from coal dust are likely !n increase considerably.

Jan 1, 1943

By K. Fagerlund

In this work, the rate of dissolution, melting behaviour and phase separation of silica flux with molten slag and matte were investigated. Mutual dissolution between high-grade matte and silica was chemically determined. Silica dissolution rates ,in various iron silicate slags was determined using the rotating rod method. The reaction and separation phenomena of slightly oxidised chalcopyrite samples and cuprous sulphide-magnetite mixtures with silica sand were examined all about 1350°C. The samples were water quenched, and polished specimens were studied and analysed using a light optical microscope ,and a scanning electron microscope with energy dispersive spectrometer. The silica dissolution rate in slag was found to increase with decreasing silica content and increasing ferric iron content. The reaction rate of silica sand' with matte was found to increase with increasing oxidation degree and magnetite content of matte:

Jan 1, 1998

By James E. Gingrich

The new Track Etch* technique for uranium exploration has been utilized in several survey programs conducted during the last few years. The results from these programs have been very encouraging, and new uranium ore bodies have been discovered by using this new technique. The Track Etch method is being used in several exploration programs in various locations around the world. The Track Etch exploration technique utilizes small pieces of special radiation-sensitive plastic film to detect the presence of radon gas which is released by uranium ore bodies. Because of the selectivity and sensitivity of the technique, ore bodies not normally detected with other surface or airborne monitoring methods are found. Since no large equipment or special training of personnel is needed, the Track Etch technique is easily used in field operations. The basis for the Track Etch method, its application in field exploration programs, and the results obtained to date in locating uranium ore bodies is discussed.

Jan 1, 1974

By J. M. Cummings

DURING the past year, the writer has investigated the treatment of a variety of British Columbia tungsten-bearing ores. Much of the test-work described in this paper was carried out in collaboration with Mr. A. G. Lyle in association with the British Columbia War Metals Research Board at the University of British Columbia. The remainder was completed in the laboratories of the Department of Mines at Victoria. Two mills in the Province are at present treating tungsten ores. Descriptions of these are included through the co-operation of Messrs. S. Gray (1) and A. A. Almstrom (2). MINERALOGY, OCCURRENCE, AND SPECIFICATIONS In the present paper, attention is directed solely to scheclite, inasmuch as known occurrences of other tungstcn minerals in British Columbia are of mineralogical interest only. The properties of scheclite are listed below: Percent W03 .. 80.6 Tenacity ...... Very brittle Çrystallization Tetragonal Lustre ........ Vitreous to resinous Cleavage ...... Good in 4 directions Magnetism ... Non-magnetic Specifie gravity 6.05 Diaphaneity .. Transparent to translucent Hardness. . . . . . 4.5-5.0 Scheelite may contain as much as ten per cent of molybdenum in solid solution, but most of the specimens from British Columbia examined by the writer were relatively pure.

Jan 1, 1943

By H. El-Faramawy, A. Ahmed, M. Eissa, M. El-Fawakhry, T. Mattar, S. N. Ghali, E. M. Kotb

As a result of the depletion of high-grade manganese reserves, it has become necessary to consider the exploitation of low-grade manganese ores. The main problem of low-grade manganese ore is the low Mn/Fe ratio, which makes it unfit for the production of manganese ferroalloys. In this work, a selective reduction technique was used for smelting low-manganese ore in the presence of coke and fluxing material in an electric submerged arc furnace to obtain a rich manganese slag and low-manganese pig iron. The product slag was blended with medium-manganese ore and smelted in an electric submerged arc furnace, in the presence of coke and the fluxing agent, to produce silicomanganese alloy. The influence of reducing agent ratio, charge basicity, and charge Mn/Si ratio on the smelting process was investigated. The optimum conditions were found to be a coke ratio of, 1.35, Mn/Si ratio of 2.0, and charge basicity of 2.5. The silicomanganese alloy produced under these conditions satisfies the specifications for Si16Mn63 and Si17Mn65. The experimental results were applied on a pilot scale, producing a silicomanganese alloy with a chemical composition close to that of the standard specifications.

Jan 2, 2022

By R. D. Leitch

Spontaneous firing of coal during storage end even during shipment has long been a serious problem, especially in some regions and with some coals, and methods for preventing such firing have been investigated at intervals for more than 70 years. Spontaneous or other firing of coal waste, either outside or inside mines, has also been a problem probably for as long as mining has been practiced extensively. Much trouble has been caused by such fires, and much money has been spent in attempts to extinguish them. It is known generally that surface waste banks in bituminous-coal fields are very likely to take fire sooner or later, but it is not known so generally that anthracite refuse-bark fires also are common and that at least some of them are more serious in their effect and results than being regarded merely as a nuisance. There surface refuse fires probably would have attracted much more than local attention long ago had it not been that they usually cause no more serious trouble than air pollution. A few supposedly effective methods of preventing or extinguishing spontaneous fires have been reported rather recently. Unless one or more of these prove to be widely applicable, methods of solving these problems are no more certain today than they have been for many years.

Jan 1, 1940

By Hung-Ming Chen

This paper presents a Cloud-based system framework for providing a web-based building information model (BIM) service. Cloud computing technologies were used to develop a BIM data center, which can handle the big data of massive BIMs using multiple servers in a distributed manner. In addition, the system allows multiple users to access the BIM data center online to submit and review BIMs concurrently. In this study, the advanced technologies/tools of web development and Cloud computing were applied and incorporated to develop a prototype system, named CloudBIM. On the client side, this study applied WebGL and HTML5 in the web-based interface development to achieve the 3D display of BIMs and the dynamic interaction with viewers through browsers. Users can access the services of CloudBIM by using PCs, laptops and tablets anytime anywhere to view the 3D model via browsers, which support WebGL. On the server side, this study used Apache Hadoop, an open-sourced distributed file system based on Google?s technologies, to establish a BIM data center. The Hadoop Distributed File System (HDFS) can utilize multiple servers to provide mass storage spaces in a distributed manner. Based on the use of Apache HBase, which provides Bigtable-like structured storage for HDFS, this study proposes database schema for storing the information from massive BIMs in two bigtables, named Object table and Property table respectively. In addition, Hadoop MapReduce, a Hadoop component for the parallel processing of large data sets, is utilized for model data acquisition by parsing the IFC files of uploaded models in parallel.

Aug 1, 2013

By J. Pepin

When using alternating current submerged arc welding (SAW) to produce pipes from microalloyed linepipe steels, it is critical to balance penetration depth and deposition rates, in order to minimize the number of weld passes while still maintaining good heat affected zone (HAZ) microstructures and properties. A series of bead-on-plate (BOP) submerged arc welds were performed on X70 steel, using different waveform variable settings (i.e., balance, offset and frequency). Weld bead cross-section profile deposition and penetration areas were measured, and both Vickers hardness and Charpy V-notch impact testing were performed. Both single electrode and tandem electrode welds were evaluated.

Jan 1, 2011

By A. Luszczkiewicz

This paper presents the beneficial effects of non-oxidative leaching of final and intermediate copper sulfide concentrates with sulfuric acid prior to the final cleaning stage of flotation. This unique process, combining leaching and flotation, appears to be advantageous for difficult-to-treat carbonate-bearing Polish copper ores, such as those processed in copper concentrators at KGHM Polish Copper. It was shown that after the chemical decomposition of about 70 % of the total carbonates naturally present in the flotation feed, a considerable enhancement of subsequent flotation results (both grade and recovery). The resulting products of non-oxidative leaching are solid hydrated calcium sulfate (gypsum), soluble magnesium sulfate and gaseous carbon dioxide. The beneficial effect established by the laboratory leaching tests was subsequently confirmed during a pilot plant operation treating final copper concentrate and a problematic intermediate concentrate at the Lubin concentrator.

Jan 1, 2007

By J. Mark Gronseth

The instantaneous shut in pressure often times is not a well defined feature of pressure-time records from in situ stress determinations by hydraulic fracturing. As the applications of in situ stress data become more sophisticated, the grea5er the need for an unambiguous method with which to identify the instantaneous shut in pressure becomes. Controlled experiments suggest that the instantaneous shut in pressure should be equated with the pressure at the inflection point of the pressure-time record following shut in. A method for determining this value is presented. Often times the minimum instantaneous shut in pressure determined after several pressurization cycles is the best estimate of the stress acting perpendicular to the fracture plane.

Jan 1, 1982