Search Documents

By C. E. Nighman, R. S. Foster

The following is a description of the methods used in rescuing men and extinguishing the underground fire at the Pennsylvania mine, Butte, Mont. , This fire, which cost the lives of 21 men, began about 9 p.m., Feb. 14, 1916, at or near a ventilating fan on the 1,200 air-shaft station. This shaft at that time was downcast, while the main hoisting shaft was upcast. Owing to the proximity of the fire to the air shaft, the air in the latter soon became heated, and as the fan on the level was not running— the power having been cut off shortly after the outbreak of the fire—the air shaft became upcast to the 300 level. At this point a blanket of cold air from the surface caused the smoke and gases to be drawn in on that level and carried down again through the workings to the 1,200. A short time after the discovery of the fire, water was turned down the air shaft through a series of pipes around the collar of the shaft, which caused the smoke to recede below the 300, so that within 2 hr. it was possible to search that level for the missing men. From the above it will be apparent why the air shaft was upcast instead of downcast, as under normal conditions, and why men were suffocated at considerable distances from the seat of the fire. The smoke and gases that came up the main hoisting shaft did not diffuse through the workings to any extent. There are doors on all levels in the connections to the main hoisting and air shafts, but in the confusion and running around many of these doors were left open, and this undoubtedly caused the smoke and gases to spread more rapidly than they would otherwise have done. It was necessary for most of the men on the various levels to pass close to the air shaft in going to the hoisting shaft, and when they encountered the smoke and gases in that vicinity a number turned back and climbed down with the direction of the air currents and were then suffocated, while all those who passed through the pall of smoke to the main shaft were saved. There were 220 men in the mine that night, and all but 25 were hoisted to the surface within 30 min. after the discovery of the fire. Of the 25, five went out through the Tramway mine, and one through the Moun-

Jan 1, 1918

By Foster Fraas

INTRODUCTION THAT variations in the humidity of the air and in the moisture content of a mixture of broken solids being separated electrostatically cause trouble is not new.1 Much of the reputation for unreliability commonly ascribed to the electrostatic separation processes is probably due to this one factor alone. Some operators dry thoroughly before separating; and while this is good in many instances, there are others in which it is not the remedy for trouble. Some mixtures behave best in very dry air and with the mixtures fed to the separator while hot to reduce the adsorbed water content. On the other hand, an overdried mixture on coming to equilibrium with more humid air, has been known to take up moisture selectively on one family of particles, as of coal in the presence of slate and clay, and give sharper electrostatic separation. From these observations it is concluded that there is a permissible moisture content for a particle and also for the atmosphere surrounding it, if in equilibrium, at which the particle will have a conductivity or contact potential2-4 that is ideal for electrostatic separation. This permissible moisture content varies between a wide range of limits for the different materials that are separated and with the kind of electrostatic separating process used. Water can be present as a result of adsorption and condensation from the atmosphere, as an accumulation before or during mining, or as a residue from a previous process step. The water may exist as a liquid film or as an adsorbed layer of vapor. If the water exceeds permissible limits it must be removed. Its state determines the method. Drying by evaporation is necessary for adsorbed water, for part of the liquid-film water (that is, up to several percent of the dry weight), and for free water in the internal structure. Large water contents may be removed by drainage or filtration. At just what point mechanical removal should cease and drying by evaporation begin depends upon the method of mechanical removal and its cost. Particles can also be separated according to their differences in dielectric constant when suspended in a liquid of intermediate dielectric constant. Recovery of this liquid presents a similar problem. PERMISSIBLE MOISTURE The adsorbed moisture on the outer surface of minerals can be quickly removed or replaced. Accordingly, in speaking of adsorbed moisture contents, either that of the solid or that of the surrounding air may be considered, the two values being connected by a distribution coefficient which varies with the temperature. However, such a condition does not necessarily exist in processes where an initially dry material is suddenly introduced into an atmosphere having a partial pressure of water vapor or where a moist material is suddenly introduced into a dry atmosphere. Here the resultant differences in the

Jan 1, 1947

A paper presenting an overview of legislative and best practice approaches to the management of OHS&E and business risk for Australian tunnelling operations. Best practice can be achieved in Australian tunnelling through ærisk awarenessÆ by decision-makers and line personnel. This will identify problems before they occur and lead to implementing controls appropriate to avoiding loss throughout the life cycle of the underground opening. The author draws on legislative approaches from all Australian states together with practical experience from risk management and risk engineering work from six recent tunnelling projects. This describes a process that:commences with concept risk assessment,involves quantification of major hazards,conducts assessments of operating risks, andleads to implementation of an integrated management system that keeps construction activities connected with the controls identified in the design and planning phases and minimises the losses sustained as a result. Key points addressed include:where the industry is going with respect to risk û methods and considerations,how tunnelling risks are perceived by the industry and legislation,how tunnel constructors and owners can minimise exposure by using proper risk engineering ætoolsÆ, andreflections on best practice methods for transferring knowledge from designers to contractors/operators.

Jan 1, 2008

By James P. Kimball

AMONG the curious results of the recent advance of prices in the iron trade of the United States, one of them at least is to be regarded as of great importance. I allude to the utilization of mill cinder as a cheap and almost costless substitute for high-priced iron ores in many blast furnaces, situated within easy reach of such raw material. It has been, with but few exceptions, the practice in this country, based upon tradition rather than upon authority or European precedents, to waste this material on 'account of its high proportion of silicic and phosphoric acids, although known to contain more iron than most ores, and although also known to be sometimes applied to the blast furnace in greater or less quantities without serious detriment to the iron for specific purposes. While in use to a limited extent in the Hocking Valley and Hanging Rock iron regions of Ohio for several years, its use in Western Pennsylvania has only become general of late, under the exigencies of high prices and a short supply of ore. Especially has mill cinder largely entered into the stock of furnaces attached to rolling mills in and about Pittsburgh. Under such circumstances the cinder pig has been paddled on the premises, and the malleable iron produced has been unexpectedly good. Cautiously as at first mill cinder has been applied, it is evident that the temptation to use it freely is a strong one whenever the commercial rates for high-class ores are out of proportion to the general conditions of the iron trade, as sometimes happens in this country, especially as the free use of it is apparently justified by the quality of the iron produced from this cheap and abundant material. Indeed the consumption of cinder pig has., not been wholly confined to mills using up the production of furnaces belonging to the same plant. One furnace at least on the Ohio, at Covington, for several' months has been making foundry pig from "all cinder." The iron has gone into the general trade. It is probable that malleable iron of good quality can he made from the poorest cinder pig, but with what degree of economy will

Jan 1, 1881

By S. Banisi, M. Poorkani

The Sarcheshmeh copper deposit contains 1 billion tones of ore averaging 0.7% copper and 0.025% molybdenum. It is located southeast of Iran and currently processes 41,000t/d. Molybdenite as a by-product is recovered in two separate stages. First, a bulk coppermolybdenum concentrate is produced and in the second stage these two are separated. The recovery of molybdenite in the first and second stages is 65% and 85-90%, respectively. The yearly production of molybdenite concentrate varies between 3500 and 4000 t. Sodium sulphide is used as the depressant of the copper and iron bearing minerals which due to a rather high consumption (17.7 kg/t) constitutes one of the major cost items of the plant (i.e., 58% of total reagents cost). A detailed laboratory scale study showed that replacing air with nitrogen could reduce the consumption of sodium sulphide (i.e., H2S or mineral origin). Nitrogen for the plant was supplied from an oxygen plant used for the smelter through a 1400 m long pipeline. The existence of the oxygen plant at the Sarcheshmeh complex was a key factor in the implementation and success of this project. After using nitrogen in the plant for a period of twenty one months, the consumption of sodium sulphide was reduced from 17.7 to 14.2 kg/t at constant metallurgy. The reduction was lower than expected which was mainly due to the type of sodium sulphide used and the lack of any automatic instrument to control the depressant (sodium sulphide) dosage. The latter in turn caused the operators to overuse sodium sulphide in order to reach and maintain the target metallurgy (i.e., higher molybdenite recovery along with lower copper content of the concentrate).

Jan 1, 2005

By Milka Madahana, John Ekoru

Particulate matter is one of the leading pollutants in the mines and in the communities in the areas near or surrounding the mines. The availability of large Clinical and environmental data sets obtained from the mines has brought about the need to use better approaches to analyze the collected data. Prediction and control of particulate matter concentration in the mining environment is essential in minimizing air pollution and protecting the respiratory health of mine workers. The main objective of this research work is to analyze datasets obtained from a mining area using machine learning techniques which will then be followed by the real-time estimation of dust particulate in the mines. Datasets collected over 8 years in an hourly sampling rate from an open cast mine is cleaned and analyzed for trends and patterns. Artificial Neural Networks (ANNs), Support Vector Machines and decision trees techniques are applied to analyze and predict the particulate concentrate. The estimation of particulate concentration using Artificial Intelligence will significantly contribute toward the development of quantitative tools to be used in correlating of cause and effect of dust concentration in mines. The results obtained in this work will form a sub-unit of a respiratory health monitoring system for mine workers. The system is essential in the collection, analysis, and tracking of mine workers’ respiratory health, thus it forms part of an early intervention system for mine workers. From the existing theory, we expect the Artificial Neural Network will perform much better than previously used classical models.

Jun 25, 2023

By P. Gautier

Current feedstock in the aluminum hot forging processes can be used in the cast or extruded forms. The microstructural variation between as-cast and extruded materials could result in different mechanical properties and corrosion resistance for hot-forged products. Corrosion performances were examined for forged parts produced by two AA6082 feedstocks at different conditions using the following corrosion tests: open circuit potential, anodic polarization, salt spray exposure and corrosion fatigue. With the help of optical and scanning electron microscopes, metallographical investigations were carried out on cast-forged and extruded-forged materials before and after corrosion. The corrosion behavior of both materials was compared in both as-forged and aged tempers. Results show that there is no significant difference in the corrosion performance for final cast-forged and extruded-forged products.

Jan 1, 2011

By K J. Riihioja, E Nozawa

SmartTag is a radio frequency identification (RFID) based technology designed to allow tracking of ore from its source through blasting, run-of-mine (ROM) pads, crushers, intermediate stockpiles and finally into the concentrator. This paper presents current developments and the future direction of the SmartTagÖ ore tracking system, as well as presenting some case studies. Successful applications of the SmartTag system have encouraged development to allow the system to be used in a wider variety of plants, in particular plants with finer crushing and screening stages. This presented Metso with a number of technological challenges, including RFID tag and antenna design. By reducing the traditional RFID tag diameter from 60 mm to 20 mm the RFID tags can now successfully pass through a secondary crusher. The new smaller RFID tags (referred to as mini RFID tags) have been used in some Process Integration and Optimisation projects with very promising results. The results indicate that the miniature RFID tags have a higher survivability to blasting and through secondary crushing stages. Extending ore tracking further through the process allows more reliable linking of spatial data with time based process performance. Metso is looking at developing even smaller micro RFID tags, and is also investigating other applications for the SmartTag system, including ore tracking from the original source to the final destination (ie from the mine, through the plant and ports to the customer).

Sep 26, 2011

By Mei-le He, Min Chen, Xiang Shen, Lei Xu, Lei Liu, Nan Wang, Xue-liang Yin

In the current study, Al2O3-MgO-CaO refractories were prepared at 1400-1600 by the addition of MnO micro-powders, and the effect of MnO addition on densification behavior of the refractory was discussed. The results showed that the doped MnO dissolved to MgAl2O4 phase, and promoted the growth of MgAl2O4 grains by the formation of MgAl2O4 solid solution. As a result, the dense microstructure was obtained, with the apparent porosity decreased from 19.2% to 5.4% and the bulk density increased from 2.78g/cm3 to 3.15g/cm3 after firing at 1600 for 2h by the addition of 4% MnO. In addition, a texture microstructure was observed, which is considered to be favorable to improve mechanical properties and the service life of Al2O3-MgO-CaO system refractories.

Jan 1, 2016

By W. G. Davenport

The flash furnace is used for smelting concentrate to (i) high-Cu matte and (ii) molten metallic copper. It is also used for converting solidified/crushed matte to molten metallic copper. This is flash converting. It consists (Table 20.1, Fig. 20.1) of: (a)tapping molten 65 to 72% Cu matte from a flash smelting furnace (b) granulating the molten matte to ?1/2 mm particles in a 103 m3/hour water torrent (c) crushing the granulated matte to 50 µm in a vertical roller mill (d)drying the crushed matte (e) feeding the dry particulate matte to a second flash furnace for oxidation converting to molten copper. In 2000, flash converting is being used by Kennecott Utah Copper (George, et al; 1995; Newman et al, 1998, 1999a,b). A second installation is being designed for the Chuquicamata smelter (www.outokumpu.com [October 12, 2000]), The potential uses of flash converting are: (a) as the second half of a flash smelting/flash converting coppermaking sequence (b) as a continuous converting alternative to batch submerged tuyere converting. This chapter uses our flash furnace matrix to determine the %O2-in-blast, industrial oxygen and oil requirements for converting solidified 65% and 72% Cu matte to molten copper. It then discusses choice of feed matte grade and other aspects of the process.

Jan 1, 2001

By T. J. Otto, C. H. Cloete, T. Mkhatshwa, T. J. van Heerden

The value realised by an open pit mine depends on the quality and integrity of the mine planning process as well as the level of execution against these mine plans. When managing the execution against the mine plan, how well the mine plan is executed spatially, is of critical importance. The short-term mine plan is the plan that is physically executed on most open pit mines. At the same time, the spatial mine-to-plan compliance is typically reconciled against the annual business plan. Short-term mine planning, therefore, plays an important role in the effectiveness of the spatial mine-to-plan compliance reconciliation process by providing operational teams with detailed designs and schedules, while ensuring that mining execution is spatially aligned with the business plan. The Sishen open pit iron ore mine (Sishen) strives to continuously improve spatial compliance to the business plan. Sishen enhanced the role that short-term mine planning plays in enabling the forward-looking component of the spatial mine-to-plan compliance reconciliation process. The enhanced short-term mine planning process focuses on detailed tactical sequence designs per mining pushback, the health of value chain buffers, spatial plan-to-plan reconciliation, and the associated management routines. This led to improved spatial mine-to-plan compliance to the business plan from 71% to 94% over the four-year period from 2020 to 2023 inclusive. These results indicate that the application of short-term mine planning as part of an integrated spatial mine-to-plan compliance process at open pit mines can contribute positively to improving the level of spatial execution against the business plan. This paper presents the enhancements made to the short-term mine planning process, which other open pit mining operations can consider to improve spatial mine-to-plan compliance.

May 27, 2025

By I. Filzwieser, A. Filzwieser

The Peirce Smith converter is the key metallurgical vessel in the majority of copper smelters. During the two step process, oxygen enriched air is injected through a row of tuyeres into the matte received from a primary smelting unit. Additionally, in the first step the iron content is oxidized into a fayalite slag by the addition of silica. During the second step, the remaining copper sulphide is converted into blister copper with a final sulphur content of approximately 200 ppm. The overall efficiency of this process is determined by the total reaction time, the slag quality and quantity, and the chemistry of the final blister copper. To increase the reaction kinetics during both stages, the METTOP Process Control and Regulation (MPCR) system was developed, which consists of four elements: OPC - Optical product control ACR - Automatic computer regulation GCU - Gas control unit GIS - Gas injection system The OPC system from SEMTECH records the optical spectrum emitted by the off gas flame providing immediate, detailed process information. Using this online data, additional gas can be automatically injected into the converter through a gas injection system opposite the tuyere zone. An improved oxygen distribution in the melt and the accurate determination of the process end point results in a significant reduction in the process cycle time. Furthermore, by maintaining the reaction closer to the equilibrium the final sulphur and oxygen content can be reduced compared to the conventional process. In particular, the final sulphur content can be lower than 70 ppm, eliminating the need for an oxidation step in the anode furnace.

Jan 1, 2007

By M. E. Rossi

In mineral resources, geologic and mining data are acquired, processed, analysed, interpreted and modelled, eventually serving as basis to generate predictions and production plans. This is a complex process, and the resulting predictions are impacted by uncertainties related to the data itself and the processing methods and techniques used. They are also impacted by the subjective decisions made by the modeler(s) at each step of the way. Knowledge, biases, skills, and prior experience come into play in the long mineral resource evaluation development workflow. It is meaningless to discuss uncertainties without evaluating the associated risks that those uncertainties imply. It is important to quantify and assess uncertainty, and to evaluate and mitigate its consequences. This paper discusses (1) conceptual and practical sources of uncertainty; (2) the utopia of an “objective” uncertainty; and (3) the quantification and public reporting of uncertainty using geostatistical conditional simulations. The objective of this paper is to postulate that the industry is running out of reasons and excuses to ignore uncertainty and risk in project evaluation. This is done in two parts, with this, the first one, presenting a more conceptual discussion. Part 2 will present case studies from different types of mining projects and operations showcasing the impact that risk assessments can have in a mining project.

Feb 22, 2026

By William E. Saegart

Copper has been mined in the Philippines since at least as early as the Ming dynasty (1368 A.D. to 1644 A. D.). The principal source areas of this early production were in Camarines Norte (Paracale), in the Mountain Province, which now boasts the largest number of Philippine porphyry copper deposits, in Masbate and in Surigao, The Spanish Era began in 1521. Although they were primarily interested in gold, the Spaniards operated several copper mines including the San Remigio mine on Panay and the Lepanto mine in northern Luzon, beginning in 1842 and 1865 respectively. Prior to World War II most of the Philippine copper production was supplied by these same two mines together with the Hixbar mine, Rapu Rapu Island which began operation in 1939. The Hixbar and San Remigio mines are cupriferous pyrite deposits and the Lepanto is a vein-¬form replacement deposit (Kinkel et al. ,I 1956). No significant copper production was derived from porphyry copper occurrences prior to world War II.

Jan 1, 1976

By S. H. Katz, J. J. Bloomfield

In studies of mine and tunnel ventilation conducted by engineers of the Bureau of Mines , various smokes are used to determine flow of air , direction of the currents , and the rate of mixing . The instrument for generating streams of sulphur trioxide (SO ) smoke , shown in the drawing herewith, has been found helpful , convenient and practicable for such purposes ; it is also especially useful in some places where fire for generating smokes is not permissible . The apparatus consists simply of a glass tube containing fuming sulphuric acid on granular pumice stone , attached to a rubber syringe bulb . When a squeeze of the bulb blows air through the tube , a stream of dense white smoke evolves, which follows and makes visible the air currents . The tubes after preparation are hermetically sealed to prevent deterioration . When ready for use , they are easily broken open at a file scratch for the purpose on both tips , and inserted into a rubber nipple at the bulb . Sometimes it is of advantage to attach them to a longer rubber tube leading to the bulb . Tubes of the size shown (about 1/2 inch outside diameter by 5 inches long) are usually sufficient for the needs of a day . Thereafter they cease to fume because the acid absorbs moisture from the air and looses its effectiveness . Smaller sizes of tubes and larger have been made , but the size shown has proved most practicable . Immediately after a person has finished using a tube it should be buried or disposed of in a place where it will not be touched by shoes or clothing, or come in contact with wooden floors , furniture , or metals , because the acid , which will eventually leak from the tubes , is highly corrosive . -- Reports of Investigations , Department of the Interior , Bureau of Mines .

Jul 1, 1923

By Bruce Regensburg

As trucks become larger and larger, haul roads take on a more significant role in mining costs and economics. The School of Mining at the University of Alberta has compiled a design manual for haul roads using both empirical and theoretical information. One section of this manual deals with the economics of haul road construction. While many mines look only at the construction costs of haul roads, this paper looks at all associated parameters including construction costs, removal costs, timing, truck productivity and width implications. The authors demonstrate the method to determine the most appropriate quality of road for different road conditions and life spans.

May 1, 2001

By Matthew Grzelak, Gulsah Erinc, David R. Chapman

"The third phase of the Bagram Drainage System project at Bagram Air Force Base in Afghanistan included construction of a shallow, 540-m long, 1.8-m inside diameter drainage tunnel. The tunnel penetrated mostly stiff to hard clayey and silty soils. The contractor’s Value Engineering Change Proposal (VECP) to use pipe-jacking with a microtunnel boring machine (MTBM) instead of the specified two-pass Earth Pressure Balance method was evaluated and supported using hand calculations. Contractor support was provided throughout the project by providing design reviews and instrumentation monitoring during construction. This paper compares the value-engineering proposal to the specified method and describes the construction conditions encountered. INTRODUCTION As part of a larger improvement project at the Bagram Air Force Base in Afghanistan, a shallow, 540-m long, 1.8-m inside diameter drainage tunnel was constructed to provide additional capacity for Coyote Creek to pass below several critical structures, including taxiways and the main runway, for mitigation of recurring flooding (see Figures 1 and 2). Overburden over the tunnel crown ranged from about 3 m to 5.5 m. An existing cast-in-place twin barrel concrete culvert runs approximately parallel to the new tunnel and is within about 8 m at its closest point. The contractor’s Value Engineering Change Proposal (VECP) to the specified two-pass Earth Pressure Balance (EPB) method (steel ribs and lagging or steel liner plate with a carrier pipe later grouted in-place) called for installation of the required drainage pipe by pipe-jacking (one-pass installation) using a slurry microtunnel boring machine (MTBM). The critical nature of the operations at the air base resulted in significant construction coordination challenges and a greater than usual need to avoid excessive settlements. Substantial restrictions were placed on drilling of investigative borings and installing instrumentation near runways and taxiways due to drill mast height. The prime contractor was SERKA TAAHHUT INSAAT A. S. (SERKA), the microtunneling subcontractor was Ludwig Pfeiffer Microtunnel GmbH & Co.KG (Pfeiffer), the jacking pipe designer was Gollwitzer Pipe and Shaft Technology GmbH (Gollwitzer), and the contractor’s tunnel engineer was Lachel & Associates, Inc. (Lachel). Lachel provided contractor support throughout the project including preparation of a VECP/Design Summary (including interpretation of existing and new geotechnical information), design reviews for jacking pipe, estimating settlement of an existing drainage structure above the new tunnel, and instrumentation planning, monitoring, and analysis during construction."

Jan 1, 2016

By R. F. Zaffarano

Intergrated energy balances and energy flows were constructed and quantified for State, regional, and national levels from four separate supply and demand commodity balances for coal, dry natural gas, petroleum and natural gas liquids, and utility electricity. These commodity balances were integrated by source and sectors through conversion and aggregation of their components to energy equivalents expressed in British thermal units (Btu). A summarization of the total gross energy components of supply and demand for commercial energy derived from direct fuels, hydropower and nuclear power, based on individual States and regions, is tabulated for 1960 and 1965. Pertinent computerization details and more than 500 individual State and regional printout tables, in both original commodity units and Btu's, are shown. Using these data, energy flows between States and regions were calculated to identify surplus and deficit energy areas. Report emphasis is on the conceptual aspects of integrated energy balances, rather than on the development of missing State energy data.

Jan 1, 1969

By A. Golpaygan

Application of Computational Fluid Dynamics (CFD) modeling for simulation of fluid flow and combustion in industrial scale electric furnace is presented. Poor combustion efficiency, roof and/or side wall overheating, carry over to off-gas system and non-ideal radiative heat transfer to processes or cooling systems have been common limiting factors causing inadequate process performance of the furnace, operational problems, and safety hazards. This paper describes how CFD analysis can be used to obtain a better understanding of commonly observed problems associated with freeboard combustion. Examples are presented to describe using combustion CFD modeling to understand requirements to diagnose a problem with furnace design including required freeboard volume or possible roof/side wall overheating.

Jan 1, 2011

By Paul W. Johnson

Economic studies of four processes for using the glass fractions obtained from processing municipal incinerator residues are presented. Three processes--brick production, floor tile production, and glass wool production--use the colored glass fraction from an incinerator residue separation plant, and the fourth process, glass spheres production, uses the colorless glass fraction. The fixed capital cost and the estimated annual operating cost for six plants are presented in the report and summarized, as follows: [ ] The value of the product obtained from each of the plants was calculated on the basis of the interest rate of return method. Each of the processes appears economically attractive when comparing the product values with estimated selling prices. However, the effect of the products on market size and price must be determined.

Jan 1, 1973