Search Documents

By O. P. Dolph

SPANIARDS were probably the first to mine the rich surface ore in the veins cutting the rhyolite capping that outcrops on the hills of La Mazata, oil the Allyones side of the Magdalena valley in Jalisco, Mexico, although the name comes from a word of Indian origin meaning "deer". The camp is about 12 km. west of Magdalena, a town on the Southern Pacific Railroad, and about 17 km. north of Etzatlán, on the Mexican National Railroad, at an elevation of 4500 ft. The climate is subtropical with no extremes of heat or cold, the rainy season beginning in June and ending in October.

Jan 1, 1938

By G. W. Grove, H. R. Burdelsky, F. E. Griffith

"INTRODUCTION The work of using a system of air locks in unsealing a mine in Ohio following a fire probably was one of the outstanding jobs of its kind in a medium-thick coal bed.The fire in this mine, thought to have been of electrical origin, was discovered at about 1:30 a.m. on December 11, 1941. Forty-four men were working in the affected section at the time; 5 escaped unassisted, and 37, who had barricaded themselves, were rescued. The bodies of two men, who had succumbed after breathing fumes given off by the fire, were brought part way out of the mine before it became necessary to seal the mine.Direct attempts to extinguish the fire with water were abandoned when hazardous amounts of 'carbon monoxide, methane, and other inflammable gases were detected in return air passing through the main haulageway and escape-way of the mine.The mine was completely sealed on the surface at about 8 p.m. on December 12, 1941, with the two bodies remaining in the mine. Sixteen days after the mine had been sealed, the two bodies were recovered. This was accomplished by air-locking through a partitioned-off stairs compartment of a ventilation shaft. This work was done under adverse barometric and atmospheric conditions.A method for collecting representative air samples from the immediate fire area was used successfully by utilizing a vacuum pump on about 10,000 feet of existing water line that had been broken near the fire area.The immediate fire region was sealed, and confined to a relatively small area; the remainder of the mine was recovered, and operations were resumed February 9, 1942, or 59, days from the time of sealing the mine on the surface. This recovery was made by air-locking the main entries inby from the shaft and No. 2 right-face entries.The distance between air locks averaged about 500 feet, and as each new set of seal stoppings and air locks was completed, the old or outby seals were taken out and the area between was ventilated. In ventilating this area, it was often necessary to use line curtains to direct the air into dead-end places."

Oct 1, 1947

By G Tsatouhas, R Newell, K Y. Wong

A sulfide ion selective electrode was used to control sulfidiser addition in the flotation testing of a synthetic and a naturally occurring ore containing malachite in order to compare the behaviour of sodium sulfide and calcium polysulfide. Both slug and controlled potential sulfidisation methods of addition were used. Under defined optimum CPS conditions, calcium polysulfide was a more effective sulfidising agent than sodium sulfide on the basis of both capital and operating costs. Surface and solution studies were used to compare the mechanism of each sulfidiser. For calcium polysulfide, XPS showed that polysulfide ions are adsorbed, whereas for sodium sulfide it is the hydrosulfide ions that are adsorbed on the mineral surface. For calcium polysulfide, the CuSx layer was believed to form on the malachite surface, which promoted the flotation of the malachite, by xanthate. Studies of surface morphology of the sulfidised malachite showed that a fairly uniform sulfidised layer is formed with both reagents. The use of sodium sulfide resulted in a thinner initial sulfidised layer compared to polysulfide at equivalent initial sulfur concentration.

Jan 1, 2005

By R. A., Pallanch

THOUGH the flotation of gold ores has come into the lime- light largely in recent years, it is not a product of recent economic conditions but rather as old as flotation itself. It could hardly be other- wise, since gold, when in the right state of comminution and surface condition, is one of the more readily floated of minerals. In early practice it was not generally recognized that gold was floated as well; it was - thought that the gold was bound up with sulphide minerals that floated, but now we know that free gold must have been floated as well.

Jan 1, 1935

By Hylton R. Brown

Although extensive research has been carried on to determine the factors affecting the explosibility of carbonaceous dusts, as much has been published on coal-dust and grain-dust explosions recent reports of loss of life and property in explosions if metal dusts emphasize the lack of information on the extent of the dust-explosion hazard in plants manufacturing or handling; aluminum, magnesium, or zinc powder, as well as other metal or mineral dusts. Early investigators believed that only the carbonaceous dusts formed explosive mixtures with air, and it was not until near the beginning of the present century that the explosibility of certain metal and mineral dusts was recognized generally. In his book, entitled "Fire and Explosion Risks," published in 1904, Von Schwartz called attention to such hazards. Many vague references to metallic-dust explosions are found in the literature, such as "a severe explosion of aluminum dust occurred in the Middle West several years ago," but very little information seems to be available on the extent of the hazard, the number of explosions, or the amount of loss caused by explosions in pants handling metallic or mineral dusts or powders other than those of a carbonaceous nature. A search of the records of insurance companies, rating bureaus, fire underwriters,and fire-protection associations as well as the files and records of Government agencies has been made to obtain authentic data on explosion losses. To indicate the extent of the hazard a summary of laboratory tests covering the explosibility of certain metal dusts, with brief reference to their uses and Methods of manufacture, and the data compiled from the information available on losses are presented in this publication.

Jan 1, 1941

By F. E. Bash

IN recent years, there have been a number of experiments conducted to determine the rates of heating and cooling of various sizes and shapes of steel ingots. Up to date, however,-most of the published data has dealt with small sized ingots, the largest being an 18-in. (46 cm.) cube, the data on which was presented before the Iron and Steel Institute in May, 1918, by E. F. Law. It is due to thus lack of information on the rate at which large ingots absorb heat and come to temperature that the heating- practice varies so widely in different plants. One of the questions over which there is much debate is the proper rate of heating of large ingots for forging and the time actually required for the center of a mass of steel to come to forging temperature. As a continuation of experiments described by M. E. Leeds1 and at the request of Mr. G. R. Norton of the Sizer Forge Co. and Mr. R. C. Drinker of the Emergency Fleet Corpn., the test described in this paper was carried out on a 24-in. (61 cm.) round ingot and the rate of heating and cooling determined under regular production conditions. The ingot had been partly forged at one end but, on developing a flaw, had been scrapped so that it was available for test. The size and shape of the ingot and its position in the furnace are shown in Fig. 1.

Jan 9, 1919

By J. Lui

The 15m high Inco flash furnace uptake was designed as a reaction chamber with the objective of destroying the H2S contained in the furnace off-gas by combustion with oxygen at about 1300?C. Until recently, the oxygen required for this purpose was injected through afterburners located at the bottom of the uptake. An undesirable side effect of this practice was the formation of build up accretions on the inside walls of the uptake. This buildup had a negative impact on both the furnace on line time and the control of the flash smelting process. In late 200 I, the afterburners were relocated to the roof of the uptake. As a result, about 80% of the uptake accretion buildup disappeared with obvious beneficial effects for the operation of the furnace. This paper discusses key flash smelting aspects that affect the operation of the flash furnace uptake such as the dusting rate, the formation of H2S in the freeboard of the furnace, and the impact of using coke to supply some of the heat required by the process. The mechanism of buildup formation and its dependence on uptake afterburners location are also examined. Prof. Yazawa's sulfide smelting thermodynamic relationships proved instrumental in understanding the conditions that influence the formation and the elimination ofH2S and uptake buildup.

Jan 1, 2003

Ilmenite (FeTiO3) is the primary global source of titaniumdioxide which is commonly used as a whitening agent in papermanufacture and a pigment in paint manufacture. In WesternAustralia ilmenite is processed by the Becher process (Becher,1963, Becher et al, 1965) where ilmenite particles are feddirectly into the furnace with coal and heated to form acomposite of elemental iron and TiO2. The mechanism of thecarbothermic reduction of ilmenite has been extensively studied(Grey, Jones and Reid, 1973; Jones, 1973; Grey and Reid, 1974;El-Tawil, Morse and Francis, 1993) and is reasonably wellaccepted.

Jan 1, 1997

By J. Jin, J. D. Miller

"Bubble attachment at hydrophobic surfaces is of critical importance in the flotation recovery of mineral resources and fundamental experimental results have been reported in the literature describing the details of film thinning, rupture, and displacement. Now, for the first time, bubble attachment phenomena are examined using Molecular Dynamics Simulations (MDS). The simulation involves a nitrogen bubble containing 906 nitrogen molecules in a water phase with 74,000 water molecules at the hydrophobic molybdenite (001) surface. During the simulation period of 1 ns, film rupture occurs and the nitrogen bubble attaches to the molybdenite (001) surface, resulting in a contact angle of about 90o. In contrast, the film is stable at the hydrophilic quartz (001) surface and the bubble does not attach. Contact angles, determined from MD simulation after stabilization of the three phase line of contact, are reported and these results agree well with experimental and MDS sessile drop results. In this way, film stability and bubble attachment are described with respect to interfacial water structure for surfaces of different polarity. For example, the interfacial water molecules for the hydrophobic molybdenite (001) surface have relatively weak interactions with the surface when compared to the hydrophilic quartz (001) surface, as revealed bythe presence of a 3 A water exclusion zone at the molybdenite/water interface. INTRODUCTIONAttachment of air bubbles to mineral particles is of fundamental importance in understanding flotation separation phenomena. It is well known that attachment of an air bubble at a hydrophobic surface includes film thinning, film rupture, and film displacement (Somasundaran, 2006; Wilson, Adlard, Cooke, & Poole, 2000). Experimental techniques, such as high speed video, can catch the process of bubble attachment at a mineral surface (Drelich & Miller, 2012; Niecikowska, Krasowska, Ralston, & Malysa, 2012). However, molecular scale information to examine the phenomena has not yet been reported."

Jan 1, 2016

By Howard N. Eavenson

ALL of the matters so far taken up by the Institute Committee on Stabilization of the Coal Industry will be of help, but it seems to be that under present conditions not very much can be expected until the railroad situation has been improved. As an instance of this, I would cite the fact of our experience at our mines in West Virginia and Kentucky. During 1917 and 1918 at our West Virginia plants we produced for our own consumption, practically entirely in the Chicago district, about 4,750,000 net tons of coal. In 1919 our output was reduced to 3,500,000 tons, this being caused partly by the shortage of orders in the few months following the armistice, but more particularly by The car shortage which began last September and continued throughout the remainder of the year, with the exception of December. This car shortage has been more acute since the first of the year, and while we now have an actual capacity here of 20,000 tons daily and have the equipment to produce it, with the possible exception of a few houses, we are able to average only about 12,000 tons, and in consequence, about 30 per cent. of our by-product ovens in the Chicago district are idle, and a number of blast furnaces are down for the want of coke. These figures, of course, refer to conditions before the strike of switchmen in April was started.

Jan 1, 1920

By T. L. Heisler

The Cigar Lake project, located in northern Saskatchewan (Figure 1), is one of the world?s largest high grade uranium deposits, with reserves of 150 million kilograms of uranium in a deposit averaging 430 metres below the surface. The Cigar Lake project is being developed by Cigar Lake Mining Corporation (CLMC) which is owned by Cameco Corporation (48.75%), Cogema Canada (36.375%). Idemitsu Uranium Exploration Canada Ltd. (12.875%) and Korea Electric Power (2%). Mining the Cigar Lake orebody is presenting a very real challenge due to the high grade and the ground conditions in and around the orebody. Presently, an underground test of various mining methods is underway.

Jan 1, 1992

By G K. N Subasinghe

Metallurgists operating Knelson Concentrators (KC) often rely on manufacturerÆs recommendations for selecting operating parameters, such as fluidising water flow rate and cycle time. Recent studies have shown that these parameters are not only dependent on the machine parameters but also on the feed characteristics, such as size distribution of the gold and gangue particles and the composition of its constituent minerals. It is known that a particle entering a KC initially traverses a circular path within the bowl. For a particle to maintain a given orbit, the required centripetal force must be supplied by external means. It has been argued that this centripetal force, which is dependent on the mass of the particle, its radial position and the rotational speed of the bowl, is provided by the fluid drag force created by inwardly moving fluidising water and the BagnoldÆs force created by the particle/particle collisions. Depending on the fluidising water flow rate, one of two situations can occur where the porosity of the bed increases or decreases, which influences the amount of material retained within the bowl. The amount of material of a given size and density retained in the bowl is thus dependent on the extent of the centripetal force provided. Based on the above concept, a criterion that can be used to predict the amount of material recovered in the bowl has been derived and validated by experimental data. It may also be construed that this criterion demarcates the transition of the bed from a packed-bed state to a fluidised state. By identifying the transition values for the different constituent mineral particles in the feed, it is possible to estimate the optimal fluidising water flow rate that would maximise gold recovery while minimising gangue recovery. In addition, the kinetics of gangue displacement by incoming heavy mineral particles were also studied using synthetic mineral mixtures. The experimental data suggests that this process follows first order kinetics and that the build-up of heavy mineral reaches a maximum. A model has been proposed to predict the optimal batch cycle time for a KC in terms of the feed characteristics and machine operating parameters.

Jan 1, 2006

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing clay mining, crushing, and grinding methods and costs at various operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that in many instances publication of total production costs may cause embarrassment to the individual operator as well as to the industry as a whole. On the other hand, operating costs are essential to a technical discussion and study of the methods employed. The attention of the reader is called specifically to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. The following report deals with the methods employed by the Malvern Clay Co., Malvern, Carroll County, Ohio. The author wishes to acknowledge the assistance of the following persons: H. C. Ross, vice-president and general manager, and H. C. Dormer, secretary and treasurer.

Jan 1, 1937

By Ron J. Elliott, Dylan Wedgewood

A series of five signature holes were blasted at the Highvale Mine and the resultant seismic data was analyzed to make recommendations on how best to address neighbour complaints regarding blast vibrations. From an analysis of peak vibration levels measured at the closest neighbour for blasting during 2016, it was determined that the blast vibration intensity varied between 1.4 to 4.3 mm/sec (0.06-0.17 ins./sec.), well below the level of concern for the onset of minor damage to residential structures, however, the frequency of the blast vibrations was between 2.2 and 9.7 Hz, which is within the range of the natural resonant frequency for a single story home. This was determined to be the cause of the neighbour complaints, as the home would be responding to the blast vibrations.

Jan 1, 2018

By Ihsan Berk Tulu, Ted Klemetti, Deniz Tuncay

"The Analysis of Retreat Mining Pillar Stability (ARMPS) program was developed by the National Institute for Occupational Safety and Health (NIOSH) to help the U.S. coal mining industry to design safe retreat room and pillar panels. ARMPS calculates the magnitude of the in-situ and mining-induced loads by using geometrical computations and empirical rules. In particular, the program uses the “abutment angle” concept in calculating the magnitude of the abutment load on pillars adjacent to a gob.In this paper, stress measurements from U.S. and Australian mines with different overburden geologies with varying hard rock percentages were back analyzed. The results of the analyses indicated that for depths less than 650 ft, the ARMPS empirical derivation of a 21° abutment angle was supported by the case histories; however, at depths greater than 650 ft, the abutment angle was found to be significantly less than 21°. In this paper, a new equation employing the panel width to overburden depth ratio is constructed for the calculation of accurate abutment angles for deeper mining cases.The new abutment angle equation was tested using both ARMPS2010 and LaModel for the entire case history database of ARMPS2010. The new abutment angle equation to estimate the magnitude of the mining-induced loads used together with the LaModel program was found to give good classification accuracies compared to ARMPS2010 for deep cover cases.INTRODUCTIONIn the early 1990s, the Analysis of Longwall Pillar Stability (ALPS) was introduced by Mark (1990) as a chain pillar design software and was generally accepted and used by the U.S. coal mining industry. Following the success of ALPS, the National Institute for Occupational Safety and Health (NIOSH) developed the Analysis of Retreat Mining Pillar Stability (ARMPS) program for designing retreat mining pillars using a similar approach as ALPS (Mark and Chase, 1997). The Australian mining industry also recognized the success of ALPS, and Colwell, Frith, and Mark (1999) calibrated the program to Australian conditions. The ALPS and ARMPS programs draw their strengths from the large databases that are used to calibrate them (Mark, 2009). However, following the Crandall Canyon Mine collapse in 2007, NIOSH had to reconsider the pillar design criteria used in deep-cover retreat mining (Mark, 2010). The ARMPS overburden load prediction algorithm was improved to more accurately predict the loading of narrow panels with high overburden depths by implementing the pressure arch concept, and this new version is called ARMPS2010."

Jan 1, 2019

By Zhibiao Guo, Jinglin You, Dongshan Yang, Yuanxin Zhao, Yuhui Li, Jingwei Gao

By utilizing collapsed gangue to create gob ribs, roof cutting and roadway maintenance (RCRM) technology enables coal pillar-free mining, presenting a novel approach. Due to their inherent structure, faults, which are common geological formations, can lead to various hazards, including fault sliding and significant deformation of roadways. In this study, a selfdesigned underground engineering simulation test device is utilized to imitate the cross-fault mining of the 11,101 working face in the Qipanjing Coal Mine (East). The objective is to examine the behavior of the surrounding rock and stress evolution. Generally, the experimental findings demonstrate that compared to the return air roadway, the RCRM roadway experiences a 3.3% decrease in maximum coal rib stress. This suggests that the implementation of this technique can effectively alleviate the stress on the surrounding rock of the roadway. The maximum coal rib stress, lateral pressure of the gob rib, and maximum deformation of the roof near the fault of the RCRM roadway are 11.3%, 25.6%, and 86.1% greater than those of the conventional geological conditions, respectively. The roadway deformation is negatively impacted by the fault structure. Based on experimental data and field measurements, a discrepancy in the maximum roof deformation between the test and field monitoring results under typical geological conditions is 8%. This indicates a favorable alignment between the test results and the real-life scenario. In conclusion, the proposed targeted control technique is implemented in the field by integrating the mining invariant equation and gangue volume expansion equation. This not only validates the effectiveness of the technology but also offers valuable insights for the future utilization of RCRM technology under comparable circumstances.

Feb 20, 2024

By C. C. Wright, T. S. Spicer

A characteristic property of bituminous coal is that upon being heated the coal becomes plastic, evolves volatile gases, and finally solidifies into coke. This fundamental characteristic is of utmost importance and is utilized in the production of the high-temperature coke upon which the steel industry is so dependent; but from the standpoint of operation in the domestic underfeed stoker this coking tendency seriously interferes with efficient combustion. When the coke formed has too strong a structure, certain difficulties result, such as low rate of burning, slow response to heat demand, and, in extreme cases, extinction of fire. The plastic mass prevents uniform distribution of air through the fuel bed and, with strongly coking coals, large dense pieces of coke are produced which have much less reacting surface than was possessed by the original coal. In both ignition and combustion of solid fuels, the extent of the reacting surface is an accelerating factor. Poor combustion permits a surplus of fuel to accumulate in the furnace because the rate of feed and the rate of combustion are not in equilibrium, and this produces an unbalanced condition detrimental to continued automatic service. In order to bum strongly coking coals satisfactorily in a conventional stoker during the three requisite types of operation—continuous, intermittent and hold-fire, frequent attention is necessary. Domestic stokers are defined by the industry as residential stoker heaters that burn 60 lb. of coal or less per hour. With a few exceptions, these units employ the underfeed principle of combustion in which both air and coal move in the same direction up and through the fuel bed. Domestic combustion equipment has difficulty in meeting the problems presented by the several variations in ash and volatile matter, in ash-clinkering tendencies, in coking properties, and in the particle size of bituminous coals. The work of Bituminous Coal Research Inc. at Battelle Memorial Institute has shown that, of these, coking characteristics and the clinkering tendencies have the greatest effect upon the operation of the conventional clinkering type of stoker. Typical coke formations in a clinkering type of underfeed domestic stoker are illustratcd in Fig. I, which shows (A) the ideal fuel bed obtained with a noncoking or free-burning coal; (B) the type of fuel bed formed with a coal that produces a weak coke; and (C) the type of fuel bed obtained with a strongly coking coal. C is characteristic of the fuel bed developed when the average Pennsylvania bituminous coal is burned in an underfeed stoker of conventional type. It is apparent from these pictures that the formation of coke trees will seriously interfere with the efficient automatic combustion of Pennsylvania bituminous coals.

Jan 1, 1942

By T. S. Spicer, C. C. Wright

A characteristic property of bituminous coal is that upon being heated the coal becomes plastic, evolves volatile gases, and finally solidifies into coke. This fundamental characteristic is of utmost importance and is utilized in the production of the high-temperature coke upon which the steel industry is so dependent; but from the standpoint of operation in the domestic underfeed stoker this coking tendency seriously interferes with efficient combustion. When the coke formed has too strong a structure, certain difficulties result, such as low rate of burning, slow response to heat demand, and, in extreme cases, extinction of fire. The plastic mass prevents uniform distribution of air through the fuel bed and, with strongly coking coals, large dense pieces of coke are produced which have much less reacting surface than was possessed by the original coal. In both ignition and combustion of solid fuels, the extent of the reacting surface is an accelerating factor. Poor combustion permits a surplus of fuel to accumulate in the furnace because the rate of feed and the rate of combustion are not in equilibrium, and this produces an unbalanced condition detrimental to continued automatic service. In order to bum strongly coking coals satisfactorily in a conventional stoker during the three requisite types of operation—continuous, intermittent and hold-fire, frequent attention is necessary. Domestic stokers are defined by the industry as residential stoker heaters that burn 60 lb. of coal or less per hour. With a few exceptions, these units employ the underfeed principle of combustion in which both air and coal move in the same direction up and through the fuel bed. Domestic combustion equipment has difficulty in meeting the problems presented by the several variations in ash and volatile matter, in ash-clinkering tendencies, in coking properties, and in the particle size of bituminous coals. The work of Bituminous Coal Research Inc. at Battelle Memorial Institute has shown that, of these, coking characteristics and the clinkering tendencies have the greatest effect upon the operation of the conventional clinkering type of stoker. Typical coke formations in a clinkering type of underfeed domestic stoker are illustratcd in Fig. I, which shows (A) the ideal fuel bed obtained with a noncoking or free-burning coal; (B) the type of fuel bed formed with a coal that produces a weak coke; and (C) the type of fuel bed obtained with a strongly coking coal. C is characteristic of the fuel bed developed when the average Pennsylvania bituminous coal is burned in an underfeed stoker of conventional type. It is apparent from these pictures that the formation of coke trees will seriously interfere with the efficient automatic combustion of Pennsylvania bituminous coals.

Jan 1, 1942

By T. S. Spicer, C. C. Wright

A CHARACTERISTIC property of bituminous coal is that upon being heated the coal becomes plastic, evolves volatile gases, and finally solidifies into coke This fundamental characteristic is of utmost importance and is utilized in the production of the high-temperature coke upon which the steel industry is so dependent, but from the standpoint of operation in the domestic underfeed stoker this coking tendency seriously interferes with efficient combustion When the coke formed has too strong a structure, certain difficulties result, such as low rate of burning, slow response to heat demand, and, in extreme cases, extinction of fire The plastic mass prevents uniform distribution of air through the fuel bed and, With strongly coking coals, large dense pieces of coke are produced which have much less reacting surface thin was possessed by the original coal In both ignition and combustion of solid fuels, the extent of the reacting surface is an accelerating factor Poor combustion permits a surplus of fuel to accumulate in the furnace because the rate of feed and the rate of combustion are not in equilibrium, and this produces an unbalanced condition detrimental to continued) automatic service In order to burn strongly coking coals satisfactorily in a conventional stoker during the three requisite types of operation continuous, intermittent and hold-fire, frequent attention is necessary Domestic stokers are defined by the industry as residential stoker heaters that burn 60 lb of coal or less per hour With a few exceptions, these units employ the underfeed principle of combustion in which both air and coal move in the same direction up and through the fuel-bed Domestic combustion equipment has difficulty in meeting the problems presented by the several variations in ash and volatile matter, in ash-clinkering tendencies, in coking properties, and in the particle size of bituminous coals The work of Bituminous Coal Research Inc at Battelle Memorial Institute has shown that, of these, coking characteristics and the clinkering tendencies have the greatest effect upon the operation of the conventional clinkering type of stoker Typical coke formations in a clinkering type of underfeed domestic stoker are illustrated in Fig. I, which shows (A) the ideal fuel bed obtained with a noncoking or free-burning coal, (B) the type of fuel bed formed -with, a coal that produces a weal coke, and (C) the type of fuel bed obtained with a strongly coking coal C is characteristic of the fuel bed developed when the average Pennsylvania bituminous coal is ,burned in an underfeed stoker of conventional type It is apparent from these pictures that the formation of coke trees will seriously interfere with the efficient automatic combustion of Pennsylvania bituminous coals

Jan 1, 1942

By D Drinkwater

In 2009, Peter Munro and Peter Tilyard examined the “human capital” in the mineral processing sector in a paper entitled Back to the Future (Munro and Tilyard, 2009). One of their major concerns was a general decline in technical skills and process knowledge, exacerbated by lack of appreciation of the impact this can have on process plant performance and, ultimately, profitability or sustainability of the industry. There are many reasons for this decline, not least of which are the work schedules of today’s metallurgists which have a very different balance between technical and non-technical responsibility than those in the past. However, a shift towards a more technical focus has potential to deliver a range of benefits for industry at large and for the individuals in it This paper discusses some options for development of core metallurgical and process engineering skills that can be used by graduates, employers and training providers.Key skills are identified and mapped against available opportunities for development, such as existing graduate programs, on-the job training and external courses. The authors also review a number of past and present high-quality graduate development programs, including the graduate development program in place at Mount Isa Mines in the 1980s and the Anglo Platinum Graduate Development Program (AGDP) currently operating in South Africa.

Aug 8, 2011