Search Documents

1. Paper1?Identification and enumeration of asbestos fibers in the mining environment: mission and modification to the federal asbestos standard Arthur M. Langer Asbestos-related disease is increased with cumulative exposure (the concentration of asbestos in the air and duration of exposure). The maximum duration is assumed to be a working lifetime so federal agencies control cumulative exposure by limiting the airborne concentration of asbestos fibers equal to or greater than 5 lm in length. Air samples are collected in the environment of interest by entraining the airborne particulates including fibers on membrane filters and then counting the number of fibers using phase-contrast light microscopy. In addition to length, the fibers must have a length to width ratio of at least 3 to 1. This ratio is also referred to as the aspect ratio. Some counting strategies placed an upper limit on the fiber width restricting the counting to respirable fibers. Airborne asbestos is controlled by monitoring a sub-population of the airborne asbestos. No asbestos fibers shorter than 5 lm or fibers of any length having widths less than the resolution of the light optical method are counted. In the non-occupational environment, the Environmental Protection Agency requires the use of analytical transmission electron microscopy and fibers and counting fibers with lengths of 0.5 lm or greater and aspect ratios of 5 to 1 or greater are counted. The permissible exposure limit for asbestos has been reduced by more than 120-fold since 1969, when the standard was 12 fiber/ml and the current monitoring methodology was developed. The manufacturing and mining worksites are regulated by two different federal agencies and the asbestos exposure limit was higher in the mining environment until recently (Mine Safety and Health Administration 30 CFR Part 56, 57, and 7, Federal Registry, February 29, 2008). Currently the permissible exposure limit (PEL) is the same in both types of workplace and it is 0.1 fibers per milliliter (fiber/ml) over an 8-h shift as a time-weighted average (TWA). A milliliter (ml) is equivalent to a cubic centimeter (cc) and sometimes this standard is reported as 0.1 f/cc. As the phase-contrast methodology was used to monitor lower exposures and environments, other fibrous mineral particulates were incorrectly characterized as asbestos. These occurred in talc deposits and taconite ores from the Eastern Mesabi Range.

Jan 1, 2008

By S Robertson, I Buitrago

Mine life cycle planning and enduring value are taking centre stage to meet corporate goals and deliver socio-economic outcomes for communities over the life of a mine. There is a general agreement in the literature about mining-induced effects on locals adjacent to mining operations and subsequent closure. In response, international regulatory bodies, through the implementation of global agendas, encourage exploration and mining companies to embrace the concept of corporate social responsibility. This concept is designed to provide sustainable outcomes and maintain a social license to operate over the life of a mine. This paper proposes a practical application of the sustainable livelihood approach as a tool for international planning. With this approach as the governing framework, this paper proposes an innovative tool for mine life cycle planning. Based on the findings, this paper discusses the socio-economic impacts of mining and mine closure. It also argues that transferring some of the benefits from mining to create lasting value for communities needs to be considered at the initial stages of planning for the mine and the community. Findings also indicate that conditions such as a strong local government, good governance arrangements, relevant capacity-building for sustainable livelihoods and a diversified economy are important to transferring some of the benefits from mining to create lasting value for communities. The paper is based on a mixed research technique for data analysis and a case study methodology. The case studies were conducted in Australia and Colombia.CITATION:Buitrago, I and Robertson, S, ?2014. Mine life cycle planning – creating lasting value for communities, in Proceedings Life-of-Mine 2014 , pp 301–312 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By L Mikhael Gurieff, D Baas

The Phu Kham Copper-Gold Operation (Phu Kham Operation) is located in the Lao People's Democratic Republic and is owned and operated by the Lao-registered company, Phu Bia Mining Limited (PBM). Australian-headquartered copper and gold producer, PanAust Limited holds a 90 per cent interest in PBM; the Government of Laos owns the remaining 10 per cent. The Phu Kham Operation was commissioned in 2008 with an initial concentrator nameplate throughput of 12 million tonnes per annum (Mt/a). Subsequent improvement projects, including the Phu Kham Upgrade Project (PKU), completed in 2012, and the Phu Kham Increased Recovery Project (IRP), completed in 2013, increased the design throughput to 18 Mt/yr. In 2016, the actual mill throughput exceeded 19 Mt/a, this throughput is budgeted to be maintained until the end of 2020.The concentrator flotation circuit upgrade, completed during the IRP, called for a non-selective bulk sulphide concentrate to be generated from the rougher circuit. This in turn caused the mechanical flotation cells in the cleaner circuit, particularly those in the second cleaner bank, to become volumetrically overload. The overload reduced the cleaner circuit performance to approximately 92 per cent copper recovery at a 23 per cent copper concentrate grade, below the expected 95 per cent recovery. This bottleneck restricted copper units entering the plant to approximately 14.5 tonnes per hour (t/h) due to uncontrolled recirculating load build-up in the mechanical cleaning circuit.Maintaining the operating methodologies would have led to a copper production shortfall beyond 2016, to address this shortfall the Phu Kham Operation looked to optimise the Jameson Cell and mechanical cleaner circuit performance. The work included fundamental application of flotation practice and modelling, mineralogical analysis, bubble size analysis, plant surveys and test work. The results were used to develop and implement an innovative automated control system strategy incorporating flotation theory and operating strategies. The automation has the ability to quickly adapt to disturbances in the circuit and maintain optimised performance with little or no intervention by flotation operators.Upon completion, cleaner recovery increased to 95 per cent at a final concentrate grade of 23 per cent copper, and copper units entering the plant increased to 17.5 t/h.CITATION:Baas, D and Mikhael Gurieff, L, 2018. Developing flotation circuit control and automation for the Phu Kham Copper-Gold Operation concentrator, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 37–58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By J. P. Gouvea

Back-analysis of two mining-induced tremors in 2011 was used to determine a modelling criterion for the entire Klerksdorp Goldfield (i.e., Vaal Reefs region). At that time, most mining operations in the region were owned by AngloGold Ashanti (AGA) and shared many geotechnical similarities. By 2018 AGA had sold off all its Klerksdorp operations to different mining companies, which continued applying the 2011 modelling criterion. As mining activities became more remote, scattered, and isolated, the extraction of isolated blocks of ground and remnants became increasingly necessary. However, the inherited criterion allowed only minimal or no mining activities at these areas. Keeping in mind that safety is the overriding consideration, an innovative numerical modelling approach, which includes the application of peak particle velocity designs, was developed to provide practitioners in the Klerksdorp Goldfield with a suitable criterion to justifiably and safely mine isolated blocks of ground and remnants. This would not always be possible if a conformist approach was used.

Mar 14, 2024

By A. K. Ratte, C. M. Brown

"IntroductionIn autogenous mills, grinding of the ore feed is accomplished by the direct action of the variously sized rocks making up the feed on each other and the mill interior. Size reduction is achieved without the addition of grinding media foreign to the mill feed, differing in this respect from rod, ball, and pebble milling. The term ""semi-autogenous"" has entered common usage in the industry to describe autogenous mills to which supplementary grinding ball additions are made to increase the rate at which size reduction of the mill feed occurs, beyond that achieved solely by the action of rock on rock. In a semi-autogenous grinding (SAG) mill, 50Jo to 10% of the mill volume may be occupied by grinding balls, whereas a range of 25% to 45% is more usual in ball milling.The comminution of mineral ores using ""conventional"" techniques has been described in previous papers. In conventional operations, size reduction of mined ore, and liberation of the valuable mineral content, is typically accomplished using flowsheets employing two to four stages of crushing. Crushing is followed by one to three stages of grinding and classification using various combinations of rod, ball, and pebble mills. This paper describes operations employing autogenous or semiautogenous grinding as the principal stage in the comminution process. Primary crusher discharge, or in some instances run of mine ore, is fed directly to an autogenous or semi-autogenous grinding circuit. Final product sizing may be accomplished in a single grinding stage, the mills operating in closed circuit with classification equipment, or in several stages using autogenous and semi-autogenous mills for primary grinding, and ball or pebble mills for secondary grinding. In several operations a portion of the primary mill discharge is crushed in an intermediate comminution step, these circuits being called autogenousball- crusher circuits (ABC). Many different flowsheets exist, but common and important to most are crushed ore stockpiles, reclaim feeder and mill feed conveyor systems, pumps, screens, and classifiers. Autogenous grinding is employed in both wet and dry processes, although today wet predominate."

Jan 1, 1989

By Harry H. Ku

In December 1975, a report entitled "An Evaluation of the Accuracy of the Coal Mine Dust Sampling Program Administered by the Department of Interior" [1] was prepared by the Analytical Chemistry Division of the National Bureau of Standards (NBS), in response to a request by Senator Harrison A. Williams. Chairman, Committee on Labor and Public Welfare. The report attempted to evaluate the adequacy of (1) the personal sampler unit used to measure the coal dust concentration in the mines, (2) the procedures used by the Department of Interior (DOI) to analyze the dust samples obtained from mine operators, and (3) any recent studies made by the Department or private industry concerning the coal dust sampling equipment. Recommendations in the report of NBS included continued research efforts by the appropriate organization to correct the personal sampler deficiencies and to consider the use of area or stationary samplers as a supplement to the personal samplers. Concurrent with the NBS report cited above, the General Accounting Office (GAO) also issued a report in December, 1975 [2], suggesting that improvements are still needed in coal mine dust sampling programs and procedures relating to penalty assessments and collections. Among recommendations made by GAO, the following paragraph specifically called for actions by the agencies involved:

Jan 1, 1979

By Lawrence G. Houk

In modern warfare mica is truly indispensable. The coordination of combatant units necessitates maintenance of intricate communications equipment, in the construction of which high-grade sheet mica is essential. Scrap, ground, and the poorer qualities of block mica, which are less essential to the military program, are not considered in this paper. Furthermore, as the paper is designed primarily to assist mica miners, mica derivatives such as splittings and films are also excluded from discussion. The paper therefore relates solely to block mica of strategic quality.

Jan 1, 1942

By Madan M. Singh

The use of fluid jets for industrial purposes has received considerable attention in recent years. The convening of The First International Symposium on Jet Cutting Technology1 in April 1972 devoted solely to this subject probably heralds the coming of age of this new science. It is interesting to note the emphasis in the conference towards the cutting of rocks, minerals, and soils, indicating the attention being devoted to excavation and mining. The use of water streams for mining of minerals is not new. It is well over a century since its first application.2 But its use in coal mining has been somewhat restricted over the years. In the past 30 years the U.S.S.R. has successfully used water for coal extraction, and these techniques have been examined in 15 countries in recent years. In the United States research on various aspects of the method has been conducted for over 15 years,3 but success stories from the Soviet Union,4 JapanS and Canada6 in the last 5 years has spurred greater enthusiasm. IIT Research Institute has done pioneering work in the 7-12 13-15 area of water jetting for rock and coal breakage. It has just completed an experimental study involving mining of coal with a 50,000-psi and 100,000-psi jet in a stripping operation14 under the sponsorhip of the U. S. Bureau of Mines (Contract No. HOll1789). As a complementary program the Bureau initiated a project to design a water-jet coal-mining machine (Contract No. H0133119). IITRI was a successful bidder on this competitive procurement.

Jan 1, 1974

By M. E. Lombardi

IN comparison with the mining industry the petroleum industry is new and inexperienced, and until now it might have been called the fortunate industry. Its great good fortune consisted in two things; a bountiful supply hidden by nature in the rocks of the earth, and a steady and large increase, during the past twenty-five years, in the demand for petroleum products. It is a remarkable fact that consumption of gasoline in the United States has shown an increase every year since automobiles first became important, and even in 1930 there was a four per cent increase, in spite of the universal depression; the estimated increase if the times had been normal, was ten per cent. This industry has, therefore, not passed

Jan 1, 1931

By Lihong Zhou, DAVOOD BAHRAMI

A reliable and stable ventilation system is essential to the safe operation of underground mines. The stability of a mine ventilation system becomes extremely critical while responding to a fire incident since an unstable ventilation system will pose a risk of airflow reversal. The reversed airflow could bring the fire contaminants such as toxic gases and smoke unexpectedly to working areas. In the past few years, there has been a growing interest in the study of ventilation network stability using the concept of resistance sensitivity, which is described as an indicator of how the airflow in an airway is reacting to a resistance change of other airways. Several methods of calculating the resistance sensitivity in a mine ventilation network have been carried out by researchers and scholars around the world. However, the proposed methods heavily rely on a vast amount of mine ventilation simulations, which are very time consuming and computer-power intensive, especially for a large-scale mine ventilation network. In this paper, a derivative method calculating the resistance sensitivities with a single mine ventilation simulation has been developed and implemented into a mine fire simulation software, MFIRE. The results from the derivative method were verified against the results from a traditional method. The derivative method has been proven to be reliable and accurate.

Jun 7, 2022

By P. Malíková, I. Osičková, R. Sousedíková, P. Rys, J. Dvořáček, S. Heviánková

Each mining project goes through the same life-cycle, from prospecting and exploration to closure and post-closure periods. This prompts the question whether the closure of a mine constitutes the end of its life-cycle or whether the decommissioned mine can be employed for some other purpose. Best-practice references indicate that there are many viable options. In our opinion, the production of service water is one such option. Laboratory research was carried out on the water from a flooded underground coal mine in Ostrava- Karviná coal district, Czech Republic, concerning the production of service water from pumped minewater. The research proved the practical feasibility of service or process water production. Given the effect of global climate change with regard to water resources, good prospects for this additional resource can be assumed since the water has to be pumped in any case for safety reasons.

Oct 1, 2022

By M. Z. Emad, M. U. Khan, A. ur Rehman

Stemming plugs are used as an accessory in drilling and blasting industry. They supplement conventional stemming material (i.e. drill cutting) with retention of gases in the drill hole that result in better fragmentation of rock and improved explosive utilization. Better fragmentation and explosive utilization along with economic benefits enhance efficacy of the project. Incorporation of stemming plugs in drilling and blasting industry is in exercise for about thirty years. The efficiency of stemming plugs is a key factor in their rising induction in mining industry. Different studies have been conducted on the economic viability of these plugs. The focus of this paper is the selection of stemming plugs for a bench blasting operation and the examination of blasting operation efficiency based on ergonomics and human factors. Three types of stemming plugs were evaluated during multiple blasts at a limestone quarry. Their performance was evaluated using split desktop software. Based on the human factors plastic molded stemming plug (stemming plug-1) was found to be the best among all selected plugs. INTRODUCTION Surface mines and quarrying operations heavily depend on bench blasting to achieve high volumetric targets and production demands. Use of explosives is the most economic method adopted for rock breakage and movement. Extensive research had been performed to enhance explosives energy utilization. This include changing the drilling pattern, application of air decks, stemming plugs, and use of other supportive devices. Optimization of explosive energy has been a major concern in those mines that rely on drilling and blasting operation to carry out main production. Due to continually increasing cost, efficient mining demands, and associated hazards of using explosives, it is necessary to utilize explosives at their best. Efficiency of a blasting operation is generally evaluated by the fragmentation size. From post blast conditions at blasting site to efficiency of processing plant, anything can be affected due to improper blast resulting in bad fragmentation. Better fragmentation is necessity for better operation of the system along with consideration of the safety of operation, environmental issues and related costs. For developing a blast design, an engineer should always attempt to minimize the cost of operation without compromising with acceptable technical and safety necessities [1]. Blast performance is dependent on many different factors associated with the process. These factors have been gauged as blast geometry, explosive specification, and rock mass properties [2]. Similarly, in 2013 Mohammad et al. concluded that fragmentation dynamics depends on blast hole diameter, primer, spacing, stemming, burden, and delay timing for blasting operation [1]. At the work site where this study was performed, blast holes were filled by drill cuttings and muds to help in confining gases. In a blast hole, gas confinement helps in better rock fragmentation along with reduced flyrocks. This practice is most common in many countries including Pakistan. Due to lack of homogenized particle size, the effectiveness of confinement is variable and majorly based on the size of stemming. Extremely small sized drill cuttings often result in hole blow out along with flyrocks from the collar. This improper blast energy will result in poor blast, bad impacts on environment, and reduced operational efficiency. In addition to the stemming material, the length of stemming is also a prime consideration. The decrease in stemming length will increase the quantity of explosive in the blast hole and an increase in stemming material generally improves stemming performance.

Jan 1, 2019

By C. R. Ross

"THE ASSESSMENT of pneumoconiosis-producing dusts in mines and other industries is usually undertaken for one or more of three reasons: (1) To compare dust exposures at particular operations with standards of permissible dustiness in order that hazards may be evaluated and preventive procedures initiated where required.(2) To study particular operations with the objective of improving dust control devices or procedures by locating dust sources. (3) To obtain data which, along with the results of medical investigations, may assist in understanding the causes of dust-induced diseases or aid in the establishment of permissible standards of dustiness. Most dust measurements are made for the first of these reasons -to evaluate dust hazards so that they may be controlled. For this purpose, four quite different assessment techniques have been in widespread use for many years. One of these is based on the konimeter, an instrument familiar to most .Canadian mining men; a second on the impinger, which is also widely used in Canada, and almost exclusively so in the United States; a third on the thermal precipitator, used extensively in Britain and South Africa; and a fourth on the tyndallometer, a light-scattering instrument used in Germany."

Jan 1, 1960

By Mehmet Guney

This article is based on a detailed heat investigation conducted at the Rokana Division of Nchanga Consolidated Copper Mines Limited while both authors were employed in Zambia. Mindola Mine is one of the three underground mines comprising the Rokana Division on the Copperbelt of Zambia, producing about 270,000 tons of ore per month at 1.9% Cu and 0.14% Co. The total volume of air being circulated by means of five primary fan installations slightly exceeds 1,000 m3/sec at standard density. Sectional bulk cooling is practised where air cooling coils are installed at primary splits some considerable distance from the stoping operations. Total capacity of the refrigeration complex is 10,500 kw (3,500 R. tons), of which about 7,000 kw is available as effective cooling power after losses, but the heat removed from the coifs is about 3,500 kw with 61% over-all plant performance. An extension program is planned for a further five production levels with the re-deepening of a sub-vertical shaft. Thermal heat will become a major problem at increased depth associated with higher rock temperature, higher thermal conductivity of the rock groups encountered and fissure water flowing into working areas through the strata with increased rock temperature. This paper describes the ventilation and refrigeration practices in Mindola Mine, with special reference to future thermal heat problems. These are discussed with a view to mining at depth.

Jan 1, 1979

By E. A. Ziemba

The modified in-situ process is one of the methods being considered for extracting oil from oil shale. One of the questions to be answered for this approach is the environmental consequence of underground retort abandonment. This report outlines a study which addresses the question in terms of a grouting solution. It covers the development of a spent shale ash based grout which will fulfill the environmental requirements in terms of strength, stability, and impermeability. In addition, it will allow the reinjection of up to 50 percent of material mined and surface retorted as part of this process.

Jan 1, 1982

By K. A. Pauly

(Wilkes-Barre Meeting, June, 1911.) COMPRESSED air has been and is still very extensively used in connection with mining-operations, but its application in the past has been almost entirely confined to supplying power to underground machinery. Its introduction was due to the difficulty of taking care of the steam which is exhausted underground, rather than to any advantage in efficiency to be gained by its use. The ease with which electric power may be carried to the remotest parts of the mine and the high efficiency of the electric motor have long been appreciated by mine-operators, and electric power is now extensively used underground in the more recent developments, while many of the compressed-air engines in the older workings are being rapidly replaced by electric motors. Recently, however, it has been suggested to use compressed air for driving the large shaft-hoists, the air for the engines being supplied by electrically-driven compressors, and an installation of this character is being erected at Butte; Mont. It is the object of this paper to compare the compressed-air system of hoisting with the various electrical systems, from the stand-points of first-cost and cost of operation. However, before entering into a discussion of the various systems, it will be well to consider briefly the conditions affecting the choice of a system of hoisting in which electricity is the ultimate source of power. The power required by a mine-hoist is extremely intermittent and fluctuates between very wide limits, the all-day average consumption of power not exceeding from 5 to 15 per cent. of the maximum demand during hoisting. The cost of supplying power for such a fluctuating load is necessarily higher than that for supplying an equal amount of

Dec 1, 1911

By R Memary

The environmental and economic impacts of a significant dependence on fossil fuels are affecting the future of sectors such as of mining. These impacts are prompting the Australian Government to seek solutions for reducing its dependence on fossil fuels more generally, such developing clean energy and improving energy efficiency. However, limited research has been undertaken to assess the potential synergies between clean energy and mining in an uncertain global future. This paper analyses current energy use by mining in Australia and reviews the drivers and opportunities for energy efficiency and cleaner energy technologies to be coupled to mining under three future scenarios. Linkages between mining and clean energy are investigated for three global scenarios for mining and metals to 2030, developed by the World Economic Forum (WEF), namely Green Trade Alliance, Rebased Globalism and Resource Security. These scenarios are applied to assess how they could change the barriers, opportunities and trade-offs required for the development of a more sustainable energy sources by the minerals industry in Australia.

Nov 22, 2011

By James J. Anthony

High-angle in-pit conveying is an idea that is being seriously studied by a number of important mining companies in North America. Its application in coal, iron ore, and copper mining is expected to reduce mine operating costs considerably compared with the conventional discontinuous methods, such as truck haulage, which are fuel, labor, and maintenance intensive. Therefore, a mine introducing high-angle in-pit conveyors will gain a competitive advantage over mines which continue to use conventional haulage. While the capital outlay for in-pit conveyor systems obviously varies depending on pit depth, the angle of incline, and the capacity required, it generally will not exceed that of truck haulage when all Factors are taken into consideration. These factors include the cost of excavation, as measured in relation to the volume of minerals mined, the cost of building truck ramps and roads, and the capital outlay for the trucks and maintenance facilities. In many cases, in Fact, the capital outlay will be less than for truck haulage. This cost advantage will best be realized by new mines, whereas in existing producing mines the switch from truck haulage may involve the abandonment of a substantial capital asset.

Jan 1, 1983

By André de Almeida Grilo

Correias transportadoras de alta temperatura são ativos críticos para a pelotização devido ao prejuízo que sua falha pode trazer para a produção. Nesse sentido, deve-se avaliar a vida útil da correia em uso, visando, principalmente, auxiliar sua manutenção, e nesse contexto o presente trabalho tem como proposta utilizar a caracterização dos componentes e o estudo da degradação térmica do material da cobertura de correias transportadoras de alta temperatura. As caracterizações foram realizadas de modo comparativo entre três tipos distintos de correias transportadoras de alta temperatura fornecidas para a VALE S.A. Os reforços das correias foram caracterizados por FT-IR para análise qualitativa do polímero. De maneira semelhante, as borrachas foram caracterizadas por meio da análise do produto de pirólise via FT-IR e a densidade de ligações cruzadas por meio da técnica de inchamento do polímero e aplicação da equação de Flory-Rhener, o que ajudou a justificar o comportamento das diferentes marcas de correia perante a degradação térmica, estudada em um trabalho anterior. A partir desses resultados e utilizando dados de variação das propriedades mecânicas do material em função do tempo e temperatura de processo, pôde-se avaliar a taxa de dano causado a cada correia e, aplicando-se dados reais de processo, avaliou-se o desempenho das correias em trabalho.

Aug 8, 2018

By W. G. Miller, J. D. Scott, D. C. Sego

ABSTRACT An overall study was conducted to evaluate the properties and processes influencing the rate and magnitude of consolidation for oil sands fine tailings produced using different extraction processes. As part of the overall study, a comprehensive description of physical and chemical characteristics of fine tailings generated by caustic and non-caustic processes was carried out. Ultimately, the influence of these fundamental properties on the compressibility, hydraulic conductivity and shear strength properties of the fine tailings was assessed. The characteristics of the fine tailings are presented in terms of index properties, mineralogy, specific surface area, water chemistry, liquid limits, particle size distribution and structure. A difference in water chemistry was concluded to be the cause of substantial differences in particle size distributions and degree of dispersion of the comparable caustic and non-caustic fine tailings. The degree of dispersion was consistent with predictions for dispersed clays established by the sodium adsorption ratio (SAR) values for these materials. A linear variation of increasing dispersion with increasing SAR up to a SAR value of about 40 has been suggested, above which fine tailings are completely dispersed. The observed dispersed or flocculated structures (viewed using a scanning electron microscope) supported the predictions based on SAR values.

Jan 1, 2010