Search Documents

By V. F. Parry, W. S. Landers

"INTRODUCTION The primary object of this investigation was to determine changes in physical and chemical properties of subbituminous lump coal while in storage for 8 months in a typical residence and to demonstrate how this fuel may be stored without degradation or spontaneous combustion. The second object of the study was to determine how the stored coal performed in a hand-fired furnace operated under practical conditions.The investigation revealed that if care is exercised in placing sub-bituminous lump coal in a closed bin, no significant slacking or degrada¬tion occurs, no hazards arise, and over-all indicated efficiencies of about 65 to 69 percent can be obtained under practical,firing conditions that the average home owner can meet.Owing to the war emergency, much attention is being given to the proper storage of coal, and campaigns are being conducted to increase the quantity of coal being stored to relieve transportation and production overloads. Ordinarily, coal dealers do not recommend storage of subbituminous coal in homes owing to deterioration of the coal and to possible hazards from spontaneous combustion. This practice has grown from some troubles that have been experienced, which can be traced to improper preparation, improper bins, and poor technique in placing coal in a bin. There is no good reason why subbiturninous lump coal cannot be stored safely in homes."

Jun 1, 1944

By M. I. M. Darwish

In this paper, an effort was made to get more in-sight about the parameters that can affect air sparging technique optimization. Numerical simulations were used in predicting the effects of different parameters utilizing Shell?s in house MoRes simulator. The case of using air sparging to remediate source zone is considered in this work. Different air injection scenarios using continuous and pulsed air injection techniques, with different frequencies and durations, were compared. The amount of MTBE mass removed from the saturated zone and arrived to the ground surface, through the vadose zone, was the main criterion while comparing different air injection scenarios. The simulations results showed that pulsed air injection is better than continuous air injection in removing the MTBE and that the longer the OFF time is the better the MTBE removal.

Jan 1, 2008

Experimental Study of Ore Characterisation Methods for AG/SAG Mills Mining companies have long recognised the importance of ore breakage characterisation in design and optimisation of their crushing and grinding circuits. In one of the industry standard methods relevant to AG/SAG milling, ore is characterised using mainly high energy single impact tests. However recent DEM studies have suggested that breakage in AG/SAG mills is mainly due to low energy repetitive (or multiple) collisions rather than single high energy impacts. Hence a study was initiated at the JKMRC to investigate the behaviour of ores under such conditions. Carefully designed experiments have been performed using two laboratory mill sizes (0.6 m and 1.1 m diameter) to mimic the reported low energy repetitive impact breakage under low load conditions. The breakage characterisation parameters derived from standard high energy single impact tests on the same ores was then used to predict the low energy repetitive impact breakage. Significant bias was found in the simulations which clearly warranted further investigation. The extensive experimental program which followed employed three separate methods: the JKRBT (JK Rotary Breakage Tester) for high energy single impact and low energy repetitive impacts, gravity drops for low energy repetitive impacts, and laboratory mills to provide an extended number of low energy repetitive impacts. The breakage energies associated with these experiments were accurately measured with a high speed video camera. Two breakage indices, the degree of breakage (t10) and the breakage probability (S) were used to describe the breakage test results. This paper summarises the major results from this experimental study, which has facilitated the development of a new breakage characterization method relevant to AG/SAG mill modelling.

Sep 13, 2010

By Jane Li, Kevin Tom

"Research has shown that broken rock on conveyor transport systems can contribute upwards of 50% towards the overall heat load in underground mines. However, few studies have made significant efforts to predict the temperature distribution of the ore and air simultaneously, which can help implement heat management strategies. The present investigation explores a transient, analytical heat transfer model to track ore-pile temperature distributions, along conveyor systems in an example underground mine. Production rate, ambient conditions, ore pile thickness and belt velocity are adjusted to evaluate the effect on dry and wet bulb temperatures.INTRODUCTIONWith an ever increasing demand on Earth’s resources due to a multitude of factors like population growth and step changes in technology, pressure on the mining industry to bring out more ore with improved margins is a persistent challenge. Typically, high-volume producing mining methods (i.e., exceeding 5000 tons per day (tpd)) such as sublevel and block caving, room and pillar, and longwall shall utilize belt conveyors instead of trucks as the primary haulage method to surface to save on operational costs (de la Vergne, 2014). However, studies have shown that when such material transport systems are installed at mine depths with virgin rock temperatures (VRT) above 40oC, the heat dissipated by the conveyed ore can account for over 50% of the underground heat-load (Pareja, 2000; Bluhm, Jones, Moreby, & von Glehn, 2012; van den Berg, Moreby, & Kok, 2015).Unlike other types of heat sources encountered in underground mines, such as diesel machines, strata, electrical devices, and autocompression, heat transfer by conveyed broken rock is much more difficult to estimate. The seminal work of McPherson (1993) states that broken rock heat transfer is a function of its surface area, and the air’s psychrometric condition. It is additionally a function of the VRT, its specific heat, production rate, heat transfer coefficient and the residence time (Bossard, 1997; Ross, Tuck, Stokes, & Lowndes, 1997). Consequently, few studies have attempted to analytically quantify the significance of ore heat flow."

Jan 1, 2019

By J. C. Edwards, C. C. Hwang

A computational fluid dynamics (CFD) program was applied to fire spread along combustibles in a ventilated mine entry. The rate of flame spread was evaluated for the ribs and roof of a coal mine entry; timber sets; and a conveyor belt. The CFD program models char forming materials with temperature dependent thermal properties. The program solves three dimensional time dependent flow equations with a mixture fraction model for the gas phase reactions. Radiant heat exchange is evaluated for non-scattering gas. The CFD program predicted a flame spread rate of 0.0145 m / s for an actual coal mine fire in which the estimated flame spread rate was 0.0086 m / s. This overestimated flame spread rate was a possible consequence of the presence of inert materials in the mine entry’s roof and ribs. CFD fire spread rate predictions of 0.043 m / s and 0.73 m / s bounded the measured value of 0.27 m / s for fire spread along Douglas Fir timber sets in a tunnel.

Jan 1, 2006

By O. C. Blade

This report is one of a series made by the Bureau of Mines under a cooperative agreement with the American Petroleum Institute on the characteristics of commercial aviation gasolines. The series of Surveys is a continuation of like work conducted under aimil.ar cooperative agreements with the Coordinating Research Council, Inc. by the National. Bureau of Standards from 1940 through 1946 and by the Bureau of Mines from 1947 through 1949. A completed list of the series of surveys is given at the end of this paper.

Jan 1, 1951

By R deMoraes, A Bobet

The last decade has seen a resurgence of interest in lunar exploration and the emergence of countries like China and India as space fairing nations. In 2004, the US announced a new Vision for Space Exploration, whose objectives focused on human missions to the Moon and then Mars. The near future is likely to see the emergence of a worldwide drive to revisit the Moon as the first step in investigating the Solar System. To date, the Apollo missions provide our only experience of human operations on the Moon or anywhere else beyond Low Earth Orbit. Much was learned from these missions. However, their short duration means that many of the environmental effects that will be important for longer-duration missions could not be quantified. In addition, long-duration missions and infrastructure on the Moon require new technologies and capabilities, which must operate successfully and reliably in this lunar environment. Developing these technologies poses significant challenges for the exploration program. The paper discusses the risks associated with the construction of lunar surface and underground structures and the challenges to adopting the standards and rock mass classification systems developed on Earth and their applicability to the Moon. Moreover, an exchange of views to explore near-surface geologic and geotechnical profiles of the Moon is emphasized and implications of the lack of knowledge on rock mass characterisation of the Moonrock mass, the lack of theoretical/empirical experience on the use of rock mass systems outside Earth, and uncertainties.

Nov 29, 2022

By Qing-hua Tian, Li-then Cheng, Xue-yi Guo

In order to recycle valuable metals from silver separated residue, a novel method using alkaline smelting at low temperature was proposed. The main factors affecting the main metal recovery such as the smelting temperature, smelting time, liquid-to-solid ratio and alkali addition were investigated comprehensively. The behavior of the main metal elements, such as Pb, Sn, Sb and Bi in silver separated residue was also discussed. The results indicated that amphoteric metals such as Pb and Sn can be smelted into the melt, while other metal elements, such as Sb and Bi were left in the residue.

Jan 1, 2011

By H. Y. Sohn, Y. Mohassab, D. Q. Fan, M. Elzohiery

A flash ironmaking process is being developed at the University of Utah in which iron is produced directly from magnetite concentrate. The kinetics of magnetite reduction by a mixture of H and CO gases was determined in the 2 temperature range 1150–1600 °C. Over 90% reduction degree was achieved at a temperature as low as 1250 °C within 4–6 s which is the typical residence time available in a flash reactor. The kinetics results were applied to experimental data obtained in a laboratory flash reactor in which H and CO gas mixtures were 2 produced from in situ partial oxidation of natural gas with oxygen. CFD was used to simulate the laboratory reactor,and the results were in good agreement with the experimental data.

Mar 1, 2017

By C. Alexandru Sonoc

Donnan Dialysis uses ion exchange membranes to extract and separate cations. The driving force is provided by differences in chemical potential, rather than by electric fields or pressure. A Donnan Dialysis based process to recover lithium, nickel, cobalt, manganese, and organic acid lixiviant from recycled lithium ion battery cathodes is under development. In this paper we present a model of Donnan Dialysis and results of simulations of the aforementioned process. The simulations show that 170 m2 of membranes can process 1000 L of leachate ([Li+] = 0.285 M, [Co2+] = [Ni2+] = [Mn2+] = 0.095 M, pH 2) in two days and recover 94.1% of the lithium (as lithium carbonate), 99.4% of the transition metals (as mixed sulphates ready for solvent extraction), and all of the organic acid using 423 mol of H2SO4 and 268 mol of KHCO3.

By G. E. McElroy

THOUGH air jets occupy only a minor role in the ventilation of mines and other enclosures, their importance in this respect is greater than is commonly recognized and may be considerably increased as our conception of their modes of operation becomes clearer. The object of this paper is to discuss some of the ways in which air jets are involved in mine ventilation and some possible applications to the ventilation of mines and other enclosed spaces. The mention of air jets ordinarily suggests the use of some form of an air injector, such as the Venturi blower occasionally used for auxiliary ventilation in mines, or the Saccardo (injector) system used to a limited extent for ventilating railroad tunnels. Actually, the term covers such common phenomena as the discharge of air from fan pipes and coal-mine line brattices, and even from smoke stacks and fans. A knowledge of the general mode of air entrainment by jets also helps to explain certain phenomena-some mine-gas explosions, for instance-that otherwise would remain obscure. Jet action has been involved in three recent series of Bureau of Mines experiments in which the author has participated: experiments on fan-pipe discharge, on the dilution of gases discharged from a stack and on the ventilation of a ship's hold. Available data on the discharge of jets into large openings and on the design and performance of air injectors have been analyzed in considerable detail and supplementary experiments are planned for after the war. The results of the fan-pipe experiments have been combined with the analyses of data on jet discharge into large spaces, and have been published.1 The results of the stack-gas dilution tests, which refer to a jet discharged into a crosswind, have also been published2 and a paper on the design and performance of injectors has been prepared for publication.3 These technical experiments and analyses form the background and the documented evidence for the following nontechnical discussion of the use of air jets in mine ventilation. JET CHARACTERISTICS The jets commonly encountered are those in which the air is in turbulent-as opposed to laminar, or streamline-motion. The characteristics under discussion apply only to such turbulent jets and have their basis in theories of the mixing of turbulent air currents. Such jets have basic characteristics that are present, though variable in form, regardless of whether the jet expands freely in space, whether the expansion is limited by adjacent walls, or whether the jet propels air through a flow circuit. They expand at definite angles and entrain the surrounding air, even though the entrained air must be obtained by recirculation of their own air streams. As the quantity of air in motion in the mixed stream increases, the average velocity of the stream decreases. In the case of entrainment in the free

Jan 1, 1945

By Karl Dufresne

Blasting in geothermally high temperature ground and/or extremely reactive ground is an increasing common challenge for surface and underground mines. Many current PETN based non-electric and electronic detonators have manufacturer published in-hole temperature limits ranging from 55°C to 65°C (131°F to 150°F). When confronting blasthole temperatures above the manufacturer published limits, operations may request site-specific guidance and qualification for use. The advised safe loading window for in-hole PETN based detonators is often too short to be practicable for production blasting. To overcome limitations of PETN based initiation systems, surface mines with high temperature ground and/or reactive ground are known to load blastholes with a qualified high temperature bulk emulsion that are top primed with a cartridge of temperature qualified detonator sensitive emulsion plus an RDX detonating cord downline. As there is no in-hole delay detonator in this system, blasthole timing is accomplished with surface delays. Although this system is safe, top priming and surface delaying does influence floor quality and top size fragmentation, and safe loading windows times reduce blast block size and increase blasting frequency. A mining company with a site characterized by geothermally high temperature ground plus highly reactive ground employed a blasting system like the one described above. The site desires to improve blasting performance by moving to an in-hole delay initiation system that can withstand the site ground conditions. At the request of the mining house, DynaEnergetics developed an electronic initiation system for application in geothermally high temperature ground and/or extremely reactive ground conditions. The DynaEnergetics IGNEO high temperature electronic initiation system is rated for in-hole use in ground up to 150C (302°F) for 48 hours. The detonator consists of a high strength detonator with an HMX base charge and thermally resistant downline. To make up a primer, the detonator is inserted into a booster charge assembly that is fitted with a small HMX shape charge. This high energy primer is designed to be compatible and reliable for firing bulk emulsions, including those with high percentages of urea inhibition to combat reactive ground. Up to 1000 detonators may be programmed in 1ms increments up to 1500ms. The system is controlled by a digital firing panel that can be used with either a wired or wireless trigger.  The system enables high temperature and/or reactive ground sites to utilize in-hole delay initiation and realize the associated performance benefits. Conclusions and Future Work 1] The HMX based electronic initiation system permits bottom in-hole delaying in ground temperatures above 80°C (175°F). As compared to top priming and surface delaying, in-hole bottom delaying is known to improve floor quality, muckpile fragmentation uniformity and reduce oversize. 2] Field evaluation of the HMX initiation system at the Lihir Mine is continuing. 3] Work on the next generation of the HMX initiation system is underway and will bring with it expanded application range and flexibility. 

Oct 1, 2024

By G. T. Daware, M. J. Chaddha, S. P. Masurkar, P. G. Bhukte, A. Agnihotri

JNARDDC has evaluated bauxite deposits of India from the geo-technological point of view. During the evaluation studies, it was observed that bauxite deposits are associated with saprolite resources. During bauxite mining, various low-grade materials such as saprolite, laterite and low-grade bauxite are generated. These materials typically have low-alumina, high-iron oxide and high-silica content. Owing to their inferior quality, these materials cannot be used for alumina production and hence remain unutilized at the mine site. For the present study, the saprolite samples were collected from the Western Ghats bauxite deposits in India. The sintering studies were conducted on saprolite granules using a variety of parameters. The sintered granules were characterized, and their properties determined. The test results showed that bulk density, apparent density, porosity and refractoriness (PCE 1645–1659 °C) of the aggregates were within the range of refractory specifications. The feasibility tests carried out at the refractory industry indicated that the developed aggregates are suitable as refractory material and can substitute for calcined clay. Currently, high-purity clay resources used in the refractory industry are limited and fast exhausting; therefore, the industry is likely to face an acute shortage of raw materials, which will become more critical in the future. Therefore the sintered granules (aggregates) developed from saprolite, which is a mining waste, provide a low-cost, eco-friendly solution for the fast-exhausting resources of the high-purity clays. The developed process may change the Indian bauxite mining scenario because saprolite may substitute as a potential raw material for the refractory industry.

Apr 12, 2021

By O. C. Blade

A comparison of certain properties of the commercial aviation gasolines produced in the United States during October 1949, 1950, and 1951 is presented in table 1, the 1951 data being average values from tables 3 through 6 of the present report. Trends in the average values of certain characteristics of these fuels may be seen in figures 1 through 4 which also indicate the minimum and maximum values. As may be observed, with the exception of changes in kinematic viscosities, the properties of commercial aviation gasolines have not varied greatly during recent years. A list of aviation-gasoline survey reports published by the Bureau of Mines is given on page 6. A summary of the average values of the properties on jet fuels is shown in table 2.

Jan 1, 1952

By D. N. Madge

A survey is given of production scheduling systems currently in use or contemplated for future use in Cominco operations. Emphasis in this presentation is made on the chain of decisions that are made with the help of mathematical programming models. Some attention is devoted to the structural properties of the models.

Jan 1, 1966

By W. W. Odell

"It is common knowledge that extensive lignite deposits occur in the States of Montana, North and South Dakota and Texas. The total area of these deposits and the total amount of lignite in them is so great that the true economic value of lignite is seldom realized. These deposits underlie areas of thousands of square miles. The area of the lignite lands in North Dakota alone is estimated to be approximately 32,000 square miles. Nearly one-third of the total solid-fuel resources of the United States is lignite and approximately 90 per cent of this lies in the Northwest.To the people of the Northwest the more extended utilization of lignite is of fundamental importance, hence any methods for commercially producing salable products from lignite that promise further development of these great fields deserve careful study.The development of our lignite resources has been slow, partly because the districts wherein lignite is found is not thickly settled or highly developed in manufacturing industries, but also because of the physical and chemical characteristics of the lignite. Lignite is classed as a low-grade fuel and may be con¬sidered as imperfectly developed coal -which has a more or less woody structure; it may be of the brown-coal type or darker, denser and more homogeneous, approaching subbituminous coal in character. As mined it contains more than 30 per cent of moisture exclusive of the -rater of decomposition formed .then it is carbonized or burned. The heating value as determined by the calorimeter is approximately half that of good quality bituminous coal. Upon exposure to the air lignite loses part of its moisture, whereupon the lumps chock and split until after considerable exposure, a large percentage of slack is formed. It cannot be stored in large piles so successfully as come other fuels, and it some instances it is more apt to ignite spontaneously in storage or in transit then the higher grade fuels."

Feb 1, 1924

By Steven D. Dapp

The use of base grouting (tip grouting) to enhance the axial capacity of drilled shaft foundations can achieve improvements in economy and reliability for many types of projects and soil profiles. Recent experiences on a range of different construction projects in the Southeastern U.S. illustrate the most attractive opportunities for utilizing this technique and some limitations of the method. The quality assurance provided by measurements obtained during post grouting the pile toe is another important aspect favoring its use; the base grouting is shown to identify weaker piles and provide a means of remediating some deficiencies so that increased foundation reliability is achieved. This paper provides an overview of the methods used to evaluate and design for base grouted shafts along with lessons learned from several case histories.

Jan 1, 2006

When a thin film of volatile matter is deposited under vacuum on a polished coal surface, and the coated surface is examined microscopically in plane-polarized reflected light, colour changes are observed which are characteristic of the various macerals present. The colour changes appear to be mainly due to interference between light reflected at the upper surface of the film and at the film!coal interface. A variety of source materials for the volatile matter required have been tested, including powdered bituminous coal, coal tars, boron oxide, and certain resins. Bituminous coal gave the best results.

Jan 1, 1970

By L. E. Young

MUCH has been said and written on this subject and probably little new can be said. However, the point of view of the operating company changes from time to time, and more stress may be laid upon a subject today than was done some years ago, and it is with this changing point of view that the following observations are presented: The writer wishes to limit the discussion to views of a company mining bituminous coal, particularly to what the production department expects of the college grad¬uate. In an editorial in MINING AND METALLURGY for February, 1929, entitled "Is. Mining Engineering Passing?" it is stated that: It is not by accident that mining engineering courses have been general rather than special and form even today the only general engineering courses widely offered and followed by engineering students.'* * * even in this age of specialization, the mining engineers remain a body characterized particularly by broad knowledge.

Jan 1, 1929

By R. Chowdhury

The relevance of reliability studies for deep foundations is considered in this paper with special reference to pile foundations. Attention is drawn to uncertainties related to applied loads, the load-carrying capacity and the safety margin of a pile foundation. The essential steps in a reliability study are outlined. An essential goal of any study is the determination of the Reliability Index or Safety Index under different conditions of loading and operation. Calculations concerning probability of failure or success require an assumption to be made concerning the probability distribution of the safety margin. The significance of this and other assumptions should be clearly understood. Reliability approaches should be used to complement conventional deterministic studies.

Jan 1, 2010