Search Documents

By George C. Stone

The stack gases from regenerative furnaces lare very seldom utilized for the production of steam. If the temperature of the gases is not higher than 300" C. (572" F.) there is no economy in their use for this purpose, as the amount of available heat is very small and the temperature is so little above that of the steam that the interchange is too slow. With higher temperatures of the waste gases, however, good results can be obtained. At the plant of the New Jersey Zinc Co. (of Pa.) at Palmerton there are a number of return tubular boilers, each 6 ft. in diameter and 20 ft. long, with 96 3.5-in. tubes, which are heated by the waste gases from the spelter furnaces. These furnaces have continuous regenerators heating the air only and the stack gases reach the boilers at a temperature of about 450". The gas producers for one of these furnaces require 14 tons of anthracite (a mixture of Nos. 2 and 3 buckwheat), and the waste heat from the furnace gives a little more than 42 h.p. in steam. The boilers are not well adapted for the purpose, as they are much too large for the amount of heat going to them and the area of the tubes is not sufficient to take the gas from two furnaces without causing an objectionable amount of back pressure. The plant was built without any idea of using waste-heat boilers, and it was impossible to place the latter as close to the furnaces as they should be. Furnace and boiler are connected by an underground brick flue in which the temperature of the gas drops about 100°, losing 40 per cent. of its available heat. If the boilers were close to the furnaces the horse power of each would be 70 instead of 42. Even under these unfavorable conditions the boilers have been very advantageous, as one boiler easily supplies the steam necessary for two batteries of producers. With such low gas temperatures the heating surface of the boilers is, of course, not as efficient and the flue areas need to be considerably larger than for coal firing.

Jan 1, 1914

By Edmundo Tulcanaza

Increasing exploration costs and the need to reduce the time-frame from exploration to production presently demand formalized procedures to assist exploration planning and reserve analysis. Exploration planning is basically required to select the most cost-effective drilling/sampling program, and to flag the needs for data of greater relevance and reliability. Reserve analysis is necessary to determine the sensitivity of grade-tonnage relations, and to clarify the economic implications of mining when alternative technical choices are to be considered.

Jan 1, 1982

By D A. Williams, J C. J Boshoff

The properties of tailings that emanate from laterite nickel processing plants are significantly different to most other mine tailings. They typically comprise a mixture of fine materials that are made up of altered clays, chemical residues and salts. Neutralisation processes that are undertaken prior to tailings discharge result in a high proportion of gypsum in the tailings. The salinity of the pore fluid is commonly higher than 140 g/L of salts, dominated by magnesium sulfate. Hydraulically-placed tailings that undergo solar evaporation typically reach dry densities of less than 1 t/m3 of insoluble solids. In situ water contents after many months of drying may be as high as 80 per cent, and peak undrained shear strengths are unlikely to be greater than 20 kPa.This type of material is not conducive to upstream raising, from both a practicality and overall slope stability perspective. Even at rates of rise of less than 1 m/a, it is difficult to effect upstream raising on unaltered laterite nickel tailings. However, the authors have successfully designed and implemented upstream-raised laterite nickel tailings storage facilities. The upstream raises have been formed from both imported natural materials and air-dried and compacted tailings borrowed from the tailings beaches.Drying and associated strength gain has been achieved through various means of mechanical intervention, repeatedly exposing a zone of tailings to the atmosphere for evaporation. Field trials have been undertaken to optimise the approach, and the findings from the trials have been implemented in practice to allow stable upstream raises to be constructed. The cost savings and reduced environmental impact compared to high-volume downstream raises have been significant.CITATION:Williams, D A and Boshoff, J C J, 2015. Upstream raising of laterite nickel tailings storage facilities, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 271–280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By John M. Dale

As much as half of the world's known reserves of elemental sulfur occur at or near the earth's surface in natural or native sulfur deposits of volcanic or sedimentary origin. Yet these reserves constitute only a small percentage of the world's supply. Looked on as marginal materials, they remain relatively untouched despite the current demand and improved prices for sulfur. There are two main reasons for this. The first is the nature and occurrence of the deposits. They are generally small and widely scattered in remote and often arid locations, and the gangue constituents of the ore are apt to vary considerably-not only between deposits but also within deposits. The second reason is the lack of workable and economically feasible processes for recovering sulfur from the ores in such deposits. Historically, the older thermal processes in which the sulfur is vaporized away from the gangue were probably the most successful, but they were inefficient and created pollution problems. A few of the historical processes remain in operation today. Recently, however, an improved thermal process to handle all sulfur-containing surface ores has been designed under sponsorship of the Pan American Sulfur Co. A schematic diagram of this process is shown in Fig. 1. The process equipment consists of a paddle trough conveyor retort which is operated as a closed unit to prevent any air or oxygen from entering the system. Ground surface sulfur ore and heated pebbles are fed to this unit simultaneously. The ore and heated pebbles are slowly conveyed and continuously mixed down the conveyor retort. Heat from the pebbles and heat supplied to the outside walls of the trough conveyor retort raise the ore temperature above the boiling point of sulfur. Sulfur vapors and steam originating from moisture in the ore are ducted to a condenser, and the sulfur is recovered as a liquid. The gangue and the pebbles are discharged from the trough conveyor and separated-the gangue being discarded, and the pebbles being conveyed to a direct-fired rotary pebble heater where they are reheated before they are again charged into the rotary trough conveyor retort. The hot gases which pass countercurrent to the pebbles are ducted to the outside of the rotary trough conveyor where they pass countercurrent to the flow of the ore in order to maximize heat recovery and utilization.

Jan 4, 1969

By Lei Wang, Qi Zheng, Xiao-kui Che

"The wastewater emitted by gold chemical industry contained vast of different heavy metal ion, such as Zn, Cu and Ni etc. Among them Zn is the main ion in the waste water which causes the serious environment pollution. A method of preparing a kind of resin which is used for the removal of Zn by magnetic adsorbent was developed and was applied in practice. This adsorbent is a chitosan made of a kind of Fe3O4-chitosan modified by epichlorohydrin. The adsorption capacity of the absorbent and it was concluded that under the laboratory conditions, the maximum adsorbing capacity of this adsorbent could be 287.58 mg/g. The absorbent was also applied in the wastewater emitted by a gold industry in Shandong province. Its performance was tested and the result showed that the concentration of Zn ion in the wastewater was reduced from 0.58 mg/L to 0.0174 mg/L. What is more, the adsorption rate could be more than 97% when the dosage was 100L/m3 after adsorbing for 1h. KEYWORDS Selective, preparation, laboratory experiments, industry experiment, comparation INTRODUCTION Currently, most gold chemistry use cyanide to leach gold ore. Many different metals participate to this reaction besides the gold ion in this processing, so that the composition of the water is very complex. The waste water emitted by gold chemistry industry contains large amount of heavy metals. Definitely, if it was discharged without any treatment, the water would threaten the environment. The recuperation of any ion in the water would mitigate the pollution. Ion exchange resin, which is an effective material to do the water treatment with low cost, became widely applicated in this field [Yu-jiao Wang,2013]. Different kinds of resin were developed and the influence factors such as pH, adsorption properties and selectivity for different ions were investigated [CA Cruz et al,2018; PawanKumar et al.2016; Y Zhang, et al,2010; and ShengingSun, Aiqin Wang, 2006;]. The waste water mentioned in this article has a high Zn concentration, so a magic resin for Zn adsorption selectively we designed was used to manage this water. And the recovery of Zn could not only contribute to pollution abatement but also a best way to settle a dispute to the short of Zn resource. So the article mainly describes the preparation and the application of a kind of magnetic adsorbent used for the removal of Zn both in laboratory and industry. The aim of this article is to compare the effect of this resin in industry and laboratory?"

Jan 1, 2018

By Ira B. Joralernon

THREATS of a coming metal famine in the United States have filled many columns in magazines and newspapers in the past three years. This asserted menace has diverted attention from the actual results of recent exploration. Because no one had bothered to look into the facts, the statistical experts assumed that little ore was being found. They often subtracted the staggering tonnage of metals produced during the war from earlier published reserves, and assumed that the difference was all we had left. Naturally, they shuddered, with all possible publicity. For their figures showed an imminent lack of nearly all the metals needed for an industrial civilization, as well as for mechanized war. They concluded that only wholesale imports and development and production of metals by Federal agencies could avert the famine.

Jan 1, 1948

By L. E. Porter, H. P. Hassel

The state of California produced 310,-996,696 bbl. of oil and about 415,832,000 M cu. ft. of gas in 1944. Such oil production represented 18.5 per cent of the nation's production, as compared with 19 per cent in 1943 ,The tremendous demand placed upon the California fields is indicated by the monthly production in 1944, as follows: Month Barrels per Day Jan................... 809,262 Feb.................. 820,712 Mar.................. 824,592 .4pr ................. 829,973 May.................. 832,068 June.................. 846,038 July.................. 849,231 Aug.................. 858,932 Sept.................. 885,823 Oct................... 877,667 Nov.................. 876,613 Dec.................. 883,847 In all, 2100 wells in proved areas and 269 wildcats were drilled in California during the year 1944. At the end of the year, approximately 270 wells were drilling in the state, as compared with 156 wells at the same time in the preceding year. Nine new fields or new zone discoveries were made during the year, which, according to best estimates, will contribute some 77,000,000 bbl. of new reserves; in addition, the extensions of old fields will increase the new reserves about 165,000,000 bbl., or a combined total, through dis- coveries of new fields, zones, and extensions, of 242,000,000 bbl., offsetting to the extent of about 78 per cent the total oil produced during the year. Geographically, the reserves from these new field and zone discoveries and extensions are distributed as follows: Per Cent San Joaquin Valley........ 72 Coast Area............... 24 Los Angeles Basin Fields. . . 4 100 The state's reserves of crude oil at the end of the year have been estimated to be distributed as follows: The outstanding development project for the year was that of the United States Navy in the Naval Petroleum Reserve No. I, Elk Hills field. During the year, 115 wells were completed in this field, and at the close of the year an average of 19 strings of tools were drilling. This program is being jointly conducted by the Standard Oil Co. of California with the Navy and is designed to increase the production of Naval Petroleum Reserves from approxi-

Jan 1, 1945

By CHARLES DORRANGE

INTRODUCTION. CULM is a general term used in the anthracite regions for many years to denote a mixture of coal, bony coal and impurities which is sent to the refuse-banks. Thus, 35 years ago culm contained the pea and buckwheat sizes of anthracite; but to-day, and as mentioned in this paper, culm is used specifically to denote the material which passes through the smallest screen in the anthracite-breaker. The smallest size of commercial anthracite is known as No. 3 buckwheat, barley, or bird's-eye coal, and is ordinarily made through a round-punched plate having openings 3/16 in. in diameter, and over a round-punched plate with opening 3/32 in. or 1/16 in. in diameter. Thus culm will consist of coal, bony coal, slate, gravel, iron pyrite, etc., ranging in size from ? 3/32 in. down to dust. Other local terms for culm are " slush," " silt," and " dirt." The first experiments towards the utilization of anthracite culm by briquetting, and the first briquetting-work done in this country, were in 1872 at Port Richmond Piers, Philadelphia, Pa., by E. F., Loiseau.1 Clay was used as a binder and the finished briquette was water-proofed with shellac, etc. Excessive cost was given as the reason for discontinuing work at this plant. The Delaware k Hudson Co., in 1876, built a plant at Rondout, N. Y., which operated until 1880. Gas-tar was used as a binder, and anthracite screenings were briquetted for engine fuel. Excessive cost, poor results in firing, and the tendency of the fuel to cut the boiler-flues were given as the reasons for discontinuing the manufacture. The next plant was built by E. F. Loiseau about 1878, at Nesquehoning, Pa., near the No. 1 or Nesquehoning colliery

Sep 1, 1911

By K. Lomberg

In this paper the process of sampling and assaying as it relates in particular to the platinum group elements (PGEs) is presented. A discussion of the geology of PGE deposits is included to provide an understanding of the mineralization that is considered necessary prior to sampling, as this has a direct bearing on the mineral resource estimate and also the selection of an appropriate mining cut. The discussion includes the selection of the sampling technique (drilling or face sampling), the size of the sample relating to the requirements of the laboratory, the potential mining cut, as well as a reference to sampling theory. The selection of an assay technique that is appropriate and will yield the optimal result based on sample turnaround, precision, accuracy, and cost is then considered. Examples are drawn from work undertaken on the Bushveld Complex (Merensky Reef, UG2 Chromitite Layer, Platreef) and Great Dyke (Main Sulphide Zone). A discussion of the appropriate QA/QC programme includes the chain of custody, CRM selection and the QA/QC process. Keywords sampling, assaying, QA/QC, platinum group elements.

Jan 1, 2014

By L. J. Buchanan

The relationship between hydrothermal ore deposits and hot spring systems has received intensive study in recent years, particularly as a consequence of interest in the energy potential of geothermal systems. Base and precious metal deposition in surface pools and at shallow depths in modern geothermal systems has been recorded in numerous publications (1, 2, 3) Theoretical studies of hydrothermal fluid flow at depth, connected to surficial hot springs systems, have been presented by White and others (1), Cathles (2) , Henley and McNabb (3). As a result of these and additional studies, numerous hydrothermal ore deposits are thought to have originated as genetic parts of larger geothermal systems. In particular, it appears that metal precipitation is greatly enhanced in zones of boiling where volatiles and steam are escaping (4). High grade, near surface concentrations of base and precious metals, deposited as a result of partial vaporization of rising fluids, are such a common aspect of modern not spring systems that ore deposition models are becoming based on what may be called a geothermal model. In its most general terms, this model requires an anomalously high thermal gradient which acts as the driving force behind a convecting hydrothermal system. The water may be entirely meteoric or may be In part at least of other origins. The water migrates towards the higher temperature area, becomes heated, and picks up alkalies and metals by dissolving minerals along the fluid path. As water exits to the surface above the heat source, a mass balance requires the incoming hot water to rise to replace the lost water. As the water rises past the elevation where the hydrostatic pressure is insufficient to prevent boiling, then boiling will occur. Depending on the salinity and the temperature of the water, boiling can occur anywhere from great depths to near surface. Boiling results in a loss of volatiles, a pH rise in the fluid phase, cooling of the remaining fluid, a rise in oxygen fugacity, a concentration of salts in the remaining liquid, and precipitation of ore and gangue minerals.

Jan 1, 1980

By P. P. Andrieux

The recovery of the Zone G crown pillar, located between the bottom of the open pit and the top of the underground workings at the Raglan Katinniq Mine in Nunavik, started in the summer of 2008 and should be completed by the end of 2009. This article describes the rock mechanics-based approach implemented to design the recovery of this valuable block of ore. The stereophotography-based ShapeMetriX3D technique was first used to provide a comprehensive assessment of the various joint sets that comprised the pillar. Then, the statistical distributions obtained for the dip, dip direction, spacing and persistence of these sets were used in conjunction with the geometry of the large-scale faults present in the area to build and run a series of explicit rigid numerical models. Each of these models had a slightly different jointing geometry, randomly constructed from these statistical distributions. Incorporating in a properly formulated numerical model the variability of some of the input parameters has allowed the engineering team to assess in a rational and reliable manner the likelihood of success of the proposed mining method and sequence.

May 1, 2009

By Mario Gerards, Sergej Podkow, Marco Steinberg

"The JONES® WHIMS technology is based on the magnetic separation process and is widely used for the recovery of magnetically susceptible iron ore particles. The conventional machine design is well-known within the iron ore beneficiation industry for more than 50 years and recognized to be highly reliable, robust and extremely compact with the advantages of high capacity and selectivity. In 1981 Rana Gruber AS, Norway bought 14 JONES® WHIMS DP 317 separators when the magnetic separation plant was built and erected. Today, 11 of these old machines are still operating profitably and efficiently. The former supplier was the coal and minerals division of Klöckner-Humboldt-Deutz (KHD) which is today MBE Coal & Minerals Technology GmbH (MBE). This paper outlines a detailed description of the project of revamping the above mentioned old machines and describes the challenge of incorporating enhanced and newly developed technology into an existing processing plant. Further it gives an overview of the recent developments on the design of the JONES® WHIMS. In order to meet modern product requirements and to increase and secure plant productivity, in 2012 Rana Gruber AS settled a contract covering two new designed JONES® WHIMS DP 317 HFR separators to be implemented into the existing building and the upgrading of all 11 older JONES® WHIMS under the use of as many refurbished items as possible. The two new machines were fully developed by the product specialists of the supplier in cooperation with the operator Rana Gruber AS, thereby taking advantage of their great experience. The design of the new machine is based on the conventional design, i.e. the general operating mode as well as the overall dimensions are identical. Finally this paper gives an overview about the erection and commission phase of the two new machines and gives a detailed comparison between conventional and enhanced WHIMS technology."

Jan 1, 2014

The Colorado portion of the Rio Grande rift is clearly defined physiographically from the south in the San Luis valley northward to the latitude of Leadville where sediments of the Dry Union Formation (Tweto, 1961) accumulated within the subsiding rift zone. To the north of Leadville is a system of faults active in the late Tertiary, including the Mosquito fault that offset a portion of the Climax mineralization (Wallace et al., 1968). Tweto (197B) describes remnants of Dry Union Formation against the Mosquito fault north of Dillon in the Blue River valley, so it is apparent that the rift and associated sediments extended well to the north of Leadville. Kelley (1952, 1954, 1956) and Chapin (1971) have noted in New Mexico that the Rio Grande rift is a series of en echelon basins, offset to the east, with constrictions connecting them (Fig. 1). In Colorado the structural basins are offset to the west. The net effect of all the rift zone basins in New Mexico and Colorado is an arcuate pattern (Fig. 1) abutting the Colorado Plateau and Sari Juan Volcanic Province on the west. The width of the rift system gradually decreases northward to about Leadville where rift definition is not apparent.

Jan 1, 1987

Pyrometallurgy has played a very important role in southern Africa for at least four centuries. It continues to do so, and recent years have seen many exciting developments in pyrometallurgical technology. The wonderfully diverse rich mineral deposits in this area of the world have provided some unique opportunities for industrial processes to be established. The ?Southern African Pyrometallurgy 2006? conference was set up to showcase southern African pyrometallurgical operations, and to provide a forum for the exchange of ideas between people working at various types of smelters. Papers have been obtained from a wide variety of pyrometallurgical plants in southern Africa. These descriptions of plant operations (as well as some history, and highlights of current work) will provide useful reference information for some time to come. Contributions are also included from universities, research organizations, and engineering companies, so that the full spectrum of pyrometallurgical activities can be covered. The plant descriptions will be published on a website, where they can be updated as and when required, with the eventual goal of having a description of every smelter in the region. The conference venue was selected to be the 'Cradle of Humankind' world heritage area, about 40 km from Johannesburg. Not only does this keep the conference within easy reach of the city and yet far enough out into the countryside to allow people to focus on the conference, it is also within easy reach of many pyrometallurgical plants. There is a particular significance to the choice of location, in that the Swartkrans area close to the Sterkfontein Caves is the site of the earliest evidence of the deliberate controlled use of fire by human beings (about 1.3 million years ago), and this is obviously a necessary precursor to pyrometallurgy. The area also lends itself to a very wide range of outdoor, social, and cultural activities to supplement the technical content of the programme. It is hoped that activities such as a hot air balloon safari and visits to the world-renowned Sterkfontein Caves and Wonder Cave will help to make the conference a memorable one for those able to attend. I trust that the ongoing value of the papers and presentations will make all the hard work of the many contributors most worthwhile.

Jan 1, 2006

By J. C. Gathje

The Robinson copper ores were mined for many years from pits containing varying ore grades, sulfide and oxide ore types, and differing mineralogy. The ores also contain gold and molybdenum values, and their recoveries are an integral part of the flowsheet development. Metallurgical responses were characterized using a standard flotation procedure. Further studies investigated primary and regrind particle sizes, reagents, and other variables. The metallurgical testing was supported by mineralogical studies. Results demonstrated a high degree of metallurgical success for flotation. Final copper concentrates ranged in grade from approximately 28 to 30% copper and copper recoveries were 89 to 95% based on laboratory and pilot plant data.

Jan 1, 1992

By L. Tejeda, J. R. Donald, R. Parra, J. Duran, P. H. Lauzon

"Crucible slag tests were employed to evaluate different refractory brick classes for the Cerro Matoso electric furnace. Comprehensive analysis was conducted to evaluate the crucible erosion and characterize any slag/refractory reaction products.The classes of refractories investigated were:•,tar-impregnated magnesia;•,rebonded fused grain magnesia-chrome;•,direct bonded magnesia-chrome;•,alumina-chrome;•,picrochromite; and•,magnesia-alumina (spinel).It was concluded that tar-impregnated MgO bricks were the most suitable for the slag chemistry and furnace environment according to corrosion and infiltration resistance. A picrochromite (MgCr2O4) brick performed exceptionally well with regards to erosion resistance, however, the slag infiltrated extensively through the brick pores. Alumina-chrome, direct bonded magnesia-chromite, and spinel (magnesia-alumina) bricks were evaluated as not suitable for use in the furnace."

Jan 1, 1999

By William W. Adams

A larger measure of safety attended the operation of the stone quarries and related plants in the United States during the calendar year 1935 than in any other year for which annual records are available for the industry. The accident rate, covering fatalities and nonfatal injuries that disabled an employee beyond the remainder of the day on which the accident occurred, was 38.19 per million man-hours of work performed. The nearest approach to this favorable record was in 1932 when the rate was 38.48. The rate for 1934 was 41.82; hence the record for 1935 was 9 percent better than that for 1934. Reports from operating companies showed that 51 men were killed by accidents in 1935 and 4,152 men were injured. (See table 37.) The industry employed 73,005 men and performed 110,033,341 man-hours of labor, an average of 1,507 hours of work per man. Measured in man-days, the total volume of labor was 14,623,303, or an average of 200 days of 7.52 hours per day for each man employed. These figures are not strictly comparable with similar figures for the preceding year, as the, coverage of the industry was more complete for 1935 than for 1934 because special facilities were available to the Bureau of Mines for conducting the 1935 canvass that were not available for the 1934 canvass. Reports covering identical plants that were active both in 1934 and 1935 indicate a reduction of about 7 percent in the number of men employed in 1935. This fact suggests that the apparent increase in the number of workers in 1935 is attributable chiefly, if not entirely, to the more complete coverage of operating plants in 1935. The plants from which this inference is drawn employed 21,799 men in 1934 compared with 20,248 in 1935.

Jan 1, 1937

By Francisco Cubillos, Jorge Menacho, Cesar Gomez, Juan Rodríguez

Mineral flotation is the most used process to selectively separate particles of one or more minerals of interest. The process uses natural or induced hydrophobicity to collect particles on the surface of rising bubbles through collisions and formation of bubble-particle aggregates. Flotation machines must keep particles in suspension and well distributed, while at the same time, disperse a mass of air into a population of small bubbles. The efficiency of the separation depends primarily on the characteristics of the bubble population generated in the machine and its distribution and flow throughout its volume. The formation and separation of bubble-particle aggregates create two zones, with strong interactions between them, and with markedly different hydrodynamics conditions. A model describing two-phase hydrodynamics of the continuous and dispersed phases (frother solutions and bubbles, respectively), moving along the whole unit, is proposed. Bubble populations are characterized at the formation stage including the effect of the presence of frothers. Flow through the aggregates formation zone, where bubbles move freely and are closely spherical, is modeled using drift-flux analysis. In the aggregates separation zone, bubbles initially pack maintaining a water layer thick enough to prevent capillary forces to affect their shape. As water drainage proceeds, bubbles deform, capillary channels form, and a network of channels with a diameter size distribution develops; channels become narrower (permeability is reduced) as the distance from the interface increases. Froth hydrodynamics is characterized using models originally developed to describe unsaturated flow through porous solid particle beds. Effects of hydrostatic pressure are considered.

Jan 1, 2014

In recent years, Computational Fluid Dynamics, CFD, has been commonly utilized in the mining industry to model the fluid flow behavior in underground mine workings. This paper uses CFD modeling to simulate the airflow behavior in underground crosscut regions, where brattice sails are used to direct the airflow into these regions. Brattice sails are cost effective ventilation control devices for temporary or permanent use in underground mining. They can be used to deflect air into the unventilated areas such as crosscut regions. Their design and installation is a fundamental issue for maintaining a sufficient supply of fresh air and achieving effective air circulation and contaminant removal. At the same time, they should have little impact on the mine ventilation system. This paper presents the results of a two-dimensional CFD model, which examines the effects of brattice length on fluid flow behavior in the crosscut regions. The results of this study will assist in understanding the ventilation air behavior and in determining the optimum size of brattice curtain (sails), which provide a highly effective contaminant removal from the unventilated mine areas. This, in turn, helps the mine ventilation designers to meet the mine safety requirements.

Jan 1, 2009

By AIME AIME

HEREWITH is presented a preliminary report of a special committee, consisting of Erle V. Daveler, Paul D. Merica, and C. H. Mathewson (chairman), dealing with sundry matters of which many are of vital interest to all members of the American Institute of Mining and Metallurgical Engineers. As the report states, the initial purpose of the investigation was to determine ways and means to stimulate "the welfare and growth" of the Institute of Metals and Iron and Steel Divisions. However, it soon became apparent to the committee that most of the problems and possible correctives were of no less vital concern 1o members of the other Divisions and to the "unattached" group of members. Consequently, the Committee has authorized publication of the report and invites written comment from any member on the specific recommendations or on any other phase of the broad subject.

Jan 1, 1943