Search Documents

By J. Searra, M. Aboagye

"For new mining projects or for medium- to long-term areas of existing mines, drilling data is invariably on a relatively large grid. Direct estimates for selective mining units (SMUs), and also for much larger block units, will then be smoothed due to the information effects and the high error variance.The difficulty is that ultimately, during mining, selection will be done on the basis of SMUs on the final close-spaced data grid (grade control), which will then be available, i.e. the actual selection will be more efficient, with fewer misclassifications. However, this ultimate mining position is unknown at the project feasibility stage and therefore has to be estimated. This estimation is required because any cash flow calculations made on the basis of the smoothed estimates will obviously misrepresent the overall economic value of the project, i.e. the average grade of blocks above cut-off will be underestimated and the tonnage overestimated for cut-off grades below the average grade of the orebody. Similarly, unsmoothed estimates will be conditionally biased and will give even worse results, particularly in local areas of short- and medium-term planning or mining.This paper presents a case study of indirect post-processing and proportional modelling of recoverable resources designed for mediumand long-term mine planning at the Gold Fields’ Tarkwa Mine in Ghana. The case study compares long-term indirect recoverable mineral resource estimates based on typical widely spaced feasibility data to the corresponding production grade control model as well as the mine production. The paper also proposes certain critical regression slope and kriging efficiency control limits to avoid inefficient medium- to longterm recoverable estimates, and highlights the danger of accepting block estimates that have a slope of regression less than 0.5."

Jan 1, 2015

Geologists working in mountainous terrain were the first to map and interpret in three dimensions and as a result, made the first contributions to our understanding of mountain building and structural geology. However, geology during the 1900s has been dominantly a two-dimensional exercise in data gathering and interpretation. The standard output of geological surveys and university research has been the geological map and the standard methodology of the mineral explorer has been surface mapping and prospecting. The future will be concerned far more with the third dimension.

Jan 1, 1993

By PHILIPP HARTLIEB, Peter Schimek, Thomas Seidl, Pablo Segarra, José A. Sanchidrián, Juan Navarro

This paper develops a new Blastability Index to assess hole-to-hole fragmentation in bench blasting based on a new Rock Factor exclusively obtained from drill-monitoring data, that can provide an automatic assessment of rock structure, strength, and waste/ore, the effective energy factor of the explosive and the delay time per blasthole.

Feb 1, 2020

By Ben Mirabile, Alan Campoli, Rodney Poland

"The majority of U.S. underground coal mines use some form of cable bolt as supplemental support to a primary roof bolting system. Many coal operators employ the high load capacity of non-tensioned cable bolts, cable roof trusses, or solid bar trusses in an attempt to suspend the primary bolted horizon to overlying strata. However, in cases where many discontinuities exist in the roof strata or where pre-existing fractures are present, these passive supplemental support systems often cannot adequately control roof deflection. This paper examines the application of tensioned cable systems to minimize roof deflection in very laminated and fractured strata. Three underground case studies are presented to demonstrate the application of tensioned cable bolts. The first case study involves the rehabilitation of a longwall head gate in the Eagle Seam with highly laminated and fractured sandstone. The second case study examines the recovery of a longwall face in the Alma Seam. The final case study addresses rehabilitation of a longwall head gate in the Pittsburgh No. 8 Seam that was developed in a sandstone channel margin area and subjected to horizontal stress concentration.INTRODUCTIONDuring the previous decade, Jennmar Corporation has recognized coal operators' increasing interest in tensioned cable bolts. The majority of these tensioned cable bolt systems have been applied in adverse roof conditions including broken ground, high horizontal stress areas, and highly laminated roof strata. In most cases, qualitative data on roof conditions after application of tensioned cable bolt support indicate successful implementation of these systems. The qualitative evidence suggests that the combination of high load' capacity and applied tension provides superior supplemental roof support in adverse roof conditions. This research aims to quantify the effects of applied tension to cable bolts. This paper will review the types and installation of tensioned cable bolt systems, present initial laboratory test data, discuss successful case studies, and propose an instrumentation system for quantification of tensioned cable bolt performance."

Jan 1, 2010

By Versiane A. Leão

The adsorption of oleic acid and amine, by Expanded Hydrophobized Vermiculite (EHV) was studied. In appropriate conditions EHV is a good adsorbent for these flotation re-agents and the best results are obtained at situations where the chemicals are at non-dissociated form. The adsorbent shows good chemical stability and may been used in many adsorption-desorption cycles.

Jan 1, 1996

By R Strand, L Reading, G Keir

A major challenge in managing coal seam gas (CSG) water is predicting how much water will be produced as the industry develops. Klohn Crippen Berger Ltd (KCB) was commissioned by the Queensland Department of Natural Resources and Mines (DNRM) to develop a tool to forecast where, when and how much CSG water will be produced in the Surat and Southern Bowen Basins under various industry expansion scenarios.The water production tool (WPT) uses the Theis equation, a non-equilibrium groundwater flow equation that accounts for the effect of pumping time on well yield in confined aquifers, to predict water production volumes. Where multiple pumping wells are in close proximity, the required pumping rates for coal seam depressurisation are reduced. Therefore, pumping effects are projected spatially to assess interference effects between wells. Water production is then upscaled to the projected scale of the CSG industry within the Surat and Southern Bowen Basins.Two modifications were made to address the dual phase nature of CSG extraction (a transmissivity reduction factor) and the impact of weathering at the eastern margin of the Surat Basin (a ænear edge effectÆ factor). These factors modify relevant hydrogeological parameters in a consistent and defensible manner to more closely match observed water production.The WPT was verified by comparing results to equivalent Theis equation calculations and to type curves provided by CSG proponents. Calibration was achieved by varying the spatial distribution and intensity of the near edge effect factor in conjunction with a chi-squared analysis of residuals.The tool, which is now being maintained and further developed by the Centre for Water in the Minerals Industry (CWiMI), was built to balance numerical complexity against relative flexibility and simulation speed. The result is a tool that can produce statistically relevant results of prescribed scenarios to plan water handling and treatment requirements in discrete zones of operation.CITATION:Strand, R, Reading, L and Keir, G, 2013. Water production simulation tool for coal seam gas operations in Bowen and Surat basins, in Proceedings Water in Mining 2013 , pp 311-320 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By O. A. Bascur

The lack of integration of mining and metallurgical information with sufficient detail for analysis causes inefficient operation and hence sub-optimal energy and water use. It is difficult to analyze the performance of mining and metallurgical processes without an integrated view of mine transactions, stockpile inventories, process flows and assays. To take action requires real time information from manufacturing assets, corrected for gross errors from trucks, shovels, conveyors, faulty sensors, bad instrument calibration. This paper presents an infrastructure with advanced tools that sift through available data, identify and eliminate gross errors, and transform the data into business information for continuous improvement and optimization. Collaboration is a key component of improving efficiency of energy and water use, and the evolution of Web technology enables collaboration and troubleshooting of plant information to more quickly act on issues to reduce wasteful operation. Keywords: Mine Concentrator Optimization, Real Time Performance Management, Data Unification, Integration of Operational and Business systems, Mass and Energy Balances, Real Time Web Services, Equipment Availability, Efficiency.

Jan 1, 2009

By W. P. Yant

A previous report of the Bureau of Mines dealt with the toxicity of dichlorodifluoromethane, a new refrigerant that has a remarkably low toxicity. Continued research by the Frigidaire Corporation and toxicological experiments performed in the Laboratory of Applied Physiology of the University of Cincinnati revealed another organic fluoride, dichlorotetrafluoroethane, whose toxicity also appeared to be of a very low order and whose physical and chemical properties make it suitable for refrigeration purposes. In addition to low toxicity, safety in its use is further enhanced by its physical properties, which permit the design of equipment that operates at comparatively low pressures and hence mitigates the dangers and problems of leakage. The investigation described in this report was performed by the Bureau of Mines at the request and with the cooperation of the Frigidaire Corporation.

Jan 1, 1932

By Debasis Barman

TBM (TBM) mining in urban areas particularly under low overburden is a big challenge to design and excavate. During excavation of the Lucknow Metro project, in Uttar Pradesh, India the metro authorities encountered a design stretch where the TBM had to cross a sewer canal crossing of 15 m length under overburden of less than 1 m. Not only the stability of TBM due to uplift was of concern but also the stability of both banks. Most structures on the canal banks were non-engineered structures whose stability due to vibration of TBM was also of concern. Due to these risks, a method was proposed that met stability requirements for both ground and superstructures. The design was practical and cost effective to construct, and a collaborative exercise between the client, contractor and designer that took approximately 18 months to implement.

Jun 13, 2023

By Ørjan Nerland, Torgeir Haugen, Astri Eggen, Kjell Karlsrud

"Ground improvement by the deep dry mixing (DDM) method is used in Norway since the late 1970's. A brief review is given of the Norwegian guideline for ground improvement with DDM issued in 2012, but focus is on practical examples and experiences related to improving the stability of excavations and natural slopes in soft clays. Two examples deal with experiences from 10 to 18 m deep excavations in soft and partly highly sensitive clays, where DDM panels and block stabilization were used to both give sufficient stability against bottom heave and to limit lateral wall displacements. A third case deals with improving the stability of a natural slope in quick clay by installing DDM panels near the crest of the slope. To limit disturbance and excess pore pressures generated during the DDM works, vertical drains were installed in advance in between the DDM panels. This ensured that the excess pore pressures generated by the DDM works (up to 150 kPA) dissipated quickly, which was instrumental to avoid triggering a landslide during the stabilizing works.INTRODUCTIONThe lime column (LC) method developed in Sweden and Japan in the mid 1970's (e.g. Broms and Boman, 1977). Since then, there have been significant developments in Scandinavia and around the world in terms of rigs, mixing machinery and tools, and type of binders used. The method, presently named the ""Dry Deep Mixing"" (DDM) method in contrast to the wet deep mixing methods (WDM) that also have developed significantly over the past decades, e.g. Kitazume and Terashi (2013). The first application of the DDM method in Norway was in the late 1970's to improve the stability of an excavation in quick-clay, then using only lime as binder. Most DDM applications in Norway have also thereafter been to improve the stability of cuts, supported excavations or natural slopes in soft clays. The Norwegian Geotechnical Society (2012) issued in 2012 “Guidelines for design of ground improvement with DDM methods"". The following highlights design issues dealt with. The paper focuses however, on some practical cases where DDM has been used to improve stability of deep excavations and a natural slope in soft and partly highly sensitive clays."

Jan 1, 2015

Goethite ore are the third most abundant source of iron. The overwhelming part of these ore is represented by low-grade varieties which cannot be used in iron and steel industry without preliminary beneficiation. Biomass is a renewable solid fuel, which is feasible for the substitution of coke and coal in the manufacturing due to its lower contents of harmful elements and abundant raw material sources. Utilization of biomass in iron ore sintering process as heating agent and reducing agent contributes to energy conservation and emission reduction. The biomass was mixed together with goethite ore for roasting process to investigate the effects of reduction roasting. The results show that the goethite ore is dramatically reduced and magnetized into maghemite by biomass with the biomass dosage less than 20% and the roasting temperature below 650 oC. When the goethite ore roasted with biomass, the magnetization values could be enhanced more than two orders of magnitude, meets the standard of magnetic separation, which could significantly reduce the iron beneficiation cost. Keywords: biomass, goethite, reduction, magnetization, roasting

Sep 1, 2012

By Adam Levy, Thomas Novak, Sampurna Arya, Joseph Sottile, Kozo Saito

The use of a woven wire-mesh screen as part of a flooded-bed dust-scrubbing system is popular in the underground coal mining industry. It is used in combination with a demister (mist eliminator) to remove dust from the dust-laden air. A study was conducted to measure the pressure drop across a flooded-bed, wire-mesh screen at different airflow rates in one-phase (dry) and two-phase (wet) conditions. Two empirical relationships between pressure drop and air velocity were developed for dry and wet conditions, respectively. In both cases, the form of the empirical relationships was found to be similar to relationships given by Sabri Ergun for high velocity, non-Darcy, single- and multi-phase flow through porous media. The experiments were repeated on a reduced-scale model of the wire-mesh screen, and the pressure-velocity relationships obtained from the full-scale prototype experiments were tested. The test results show validation of the full-scale empirical formulae on the small-scale model with an insignificant variation. This paper presents the empirical equations for pressure drop across the wire-mesh screen in dry and wet conditions. Researchers can use these equations as a tool to predict total pressure drops for wire-mesh screens of different scale sizes.

By J. Tuzson, H. McL. Clark

Introduction Wear of pumps, wet cyclones and pipelines by suspended solid particles will impact their operating economies by limiting their useful life, reducing their reliability and increasing the amount of servicing. Erosion is considered a materials problem. The empirical solution consists of testing different materials in field applications. Such tests are time consuming and expensive. The prediction of localized wear rates, life estimates and appropriate material selection demand a better understanding of the slurry wear process in environments corresponding to those found in working equipment. Key words: Wear, Slurry abrasion, Coriolis erosion tester The slurry wear process Solid particles suspended in liquid generally move with the flow, but such particles deviate under the centrifugal and Coriolis forces encountered in pumps. The concentration of particles will increase, and a solid layer or bed may accumulate if the acceleration is directed against the flow passage wall. Large particles in dilute suspensions may impact the wall. dissipating their kinetic energies and removing material. However, particles smaller than about 11)(1 µm encounter great drag when moving through the liquid. and such par¬ticles have little kinetic energy left when they reach the wall. They cannot penetrate the stagnant boundary layers present in pumps. Therefore, small particles tend to form beds that slide along the wall, removing material by a process that could he called sliding erosion or wet abrasion. Wear by impact erosion from large particles in dilute slurries can he predicted by appropriate analytical and empirical methods. However, laboratory tests and calculations of wear rates that correspond to sliding erosion are more likely to correlate with field experience from wear under similar conditions. Specific energy Data from laboratory slurry erosion experiments have shown that the amount of material removed is approximately in proportion to the energy expended in the erosion process. Thus. the specific energy-energy expended in removing by erosion a unit volume of material-offers a simple, practical measure for the erosion resistance of materials. The concept was found to also apply to sliding erosion (Clark et al.. 1997). Generally, the study of the material-removal process in slurry erosion continues to remain a subject of research. Conceptually, if the flow velocities and accelerations could be calculated in a pump or pipeline, the energy dissipated at the passage walls could also be estimated, and the material removal rate would become known from the specific energy determined by laboratory tests. Slurry erosion testing Laboratory devices made specifically for slurry erosion testing may be grouped into the following: jet erosion devices, slurry pots and the Coriolis test machine (Pagalthivarthi and Helmly, 1992). Jet erosion devices use a slurry pump and nozzle to produce a high-velocity slurry jet that is directed at a flat material specimen, either perpendicularly or at some acute angle. Combined impact and sliding erosion are produced. but the processes cannot be separated, and the wear is difficult to assess except by weighing. Slurry pots consist of a cylindrical vessel containing the slurry of interest. In the slurry pot, test specimens are attached to a rotating arm. The samples are rotated in the slurry and experience local flow conditions that result in combined impact and sliding erosion. Wear depth measurements from detailed laboratory experiments have been successfully correlated with results from an analytical model of the process, and specific energy values have been calculated (Wong and Clark, 1995). In industrial use, the samples are weighed to determine the total material loss. Materials are ranked with respect to some reference material. The Coriolis erosion tester (Tuzson, 1984) consists of a rotor with a central cavity, from which two opposing radial passages lead out (Fig. 1). The slurry is fed to the centerof the rotor in one pass from a stirred overhead tank. The slurry particles are subjected to the Coriolis acceleration as they flow out through the radial passages. The material specimens are mounted into the radial passage walls facing the direction of rotation and are eroded by the particles that are pressed against them as they flow out radially. A narrow groove is worn into the sample within a few minutes, using a few gallons of slurry. Material removal is estimated accurately from profilometer traverses across the wear scar at different locations. The energy dissipated by the particles can be estimated, which leads to a well-defined experimental value for the specific energy.

Jan 1, 2000

The Bureau of Mines conducted a field study of respirable dust concentrations at an underground room-and-pillar oil shale mine and at the aboveground milling facility to determine the dust generation sources, personal respirable exposure, characteristic minerals, and size distribution of the dust. Major dust sources in the mine were the scaling and blasthole drilling operations, and major dust sources in the processing mill were the screening and crushing operations. Principal minerals found in the airborne respirable dust were albite, analcite, calcite, dolomite, quartz, and orthoclase. The average alpha-quartz content of mine and mill respirable dust samples was 4.1 pct and 15.5 pct, respectively. Carbonaceous material such as diesel particulate accounted for approximately 75 pct of the respirable particulate found in the mine. The average coefficient of variance of respirable dust concentrations measured with approved personal dust samplers in the mine and mill was 7.6 pct, the best precision observed to date with the personal dust sampler operated in the field.

Jan 1, 1977

By Barbara J. Arnold

The Electric Power Research Institute (EPRI) and six EPRI-member utilities are sponsoring research to define relationships between coal properties and coal handling behavior. Deratings and outages caused by plugged chutes or bunkers or frozen coal can cost utilities millions of dollars annually in lost energy production as well as in manpower to restore coal flow. There is also the added expense of maintaining redundant equipment to assure a continuous coal feed to the boiler, a common practice for utilities. Over the past two years, researchers at CQ Inc. and Iowa state university have collected and analyzed coal samples to develop a coal handleability index for utilities to use when specifying coals for their power plants. These coal samples cover ranges in ash content, rank, grindability, size distribution, and moisture content--properties that affect the handling behavior of coals. Other properties, such as the washability and ash composition, are measured as well. Over the remaining two years of the project, all of these analyses will be correlated to handling behavior, measured using a triaxial shear tester that determines the strength of a coal under compression. An index will be developed and validated at host utility power plants.

Jan 1, 1991

By R. A. Wood, R. I. Jaffee, H. R. Ogden, D. N. Williams

The tensile properties, creep resistance. and thermal stability of highly alloyed Ti-Al-Zr alloys were examined. On the basis of these studies, the Ti-7Al-1ZZr composition was selected for more complete evaluation. The alloy was found to be weldable and free from excessive directionality. In addition, it developed maximum properties without requiring heat treatment other than an annealing operation in the alpha field. The alloy was recommended for scale up and is presently being investigated on a production-level basis. One of the more attractive properties of titanium alloys is their ability to withstand stress at moderately high temperatures, and a considerable amount of effort has been devoted to increasing the maximum service temperature of titanium alloys. This work has suggested that the optimum alloys for high-temperature service will be single-phase a (close-packed hexagonal) alloys containing significant amounts of aluminum. However, the maximum amount of aluminum which can be alloyed with titanium is between 6 and 8 pct,l since at high-aluminum contents an embrittlement reaction occurs in the anticipated service temperature range, 800" to 1100°F. It has been shown that the embrittlement reaction involves decomposition of the high-aluminum a phase to one or more new phases.' Since this reaction does not occur at intermediate or low-aluminum contents, it was felt that intermediate Ti-A1 alloys might be strengthened by a-soluble ternary additions without inducing the embrittlement reaction. The first alloying addition considered was tin, which shows extensive solubility in a titanium and has moderate strengthening tendencies. Unfortunately, it was soon apparent that tin also promoted the embrittlement reaction, and that to obtain a stable alloy, the aluminum content had to be reduced as the tin content was increased. The second alloying addition considered was zirconium, which is similar to tin in its effects on titanium. This element did not contribute to the embrittlement reaction and, in fact, appeared to increase the maximum amount of aluminum which could be alloyed with titanium without inducing instability. This paper describes an investigation of the Ti-A1-Zr a alloy region. Alloys containing from 4 to 12 pct A1 and from 6 to 15 pct Zr were examined. The properties of these alloys are described and the bases for selecting an optimum composition is outlined. This composition, Ti-7A1-12Zr, is presently being scaled up in tonnage quantities, and is being evaluated extensively throughout the industry. In addition to presenting the basis for its selection, this paper presents a description of the properties developed in laboratory material as determined during the alloy investigation. These properties suggest that this alloy can fill an important position in applications requiring light weight, fabrica-bility, weldability, and strength to 1000oF or higher. EXPERIMENTAL PROCEDURES Titanium alloy ingots were prepared by inert electrode arc melting under an argon atmosphere. Alloying elements used were 110 Bhn titanium sponge, high-purity aluminum, and reactor-grade zirconium. Pancake-shaped ingots were prepared weighing approximately 300 g. The composition of the ingots was checked by weight measurements before and after melting. The pancake ingots were forged at 2000°F to approximately half their original thickness to give a flat plate roughly 1/2 in. thick. This plate was then rolled at 1800' to 1600°F to 0.250 in. thick. All of the alloys examined fabricated well. However, alloys containing 15 pct Zr tended to overheat due to exothermic oxidation, and scaling was excessive. As might be anticipated from its effect in decreasing the ß transus, increased zirconium appeared to improve fabricability somewhat, especially during rolling at lower temperatures. Except for a limited study of heat-treatment response, all alloys were examined in the a-annealed condition. Prior to heat treatment the a and ß tran-sus temperatures were determined by metallo-graphic examination of samples quenched after annealing at 50-deg intervals in the transformation region. These data are shown in Fig. 1. Recrystal-lization appeared to occur in about 1 hr in the range 1300º to 1500ºF. Therefore, alloys were annealed for 1 hr at 1550ºF (4 and 5 pct Al), 1600ºF (6 through 7-1/2 pct Al), or 1650°F (8 or more pct Al). This produced an equiaxed a grain structure. In most alloys, a "ghost" structure was visible after the a-annealing treatment, as shown in Fig. 2. This structure apparently resulted from the acicular

Jan 1, 1963

By Ronald B. Stone

This paper describes a proposed solution to the problem of mining a 315 foot diameter unsupported sphere at a depth of 2700 feet in a salt dome by conventional mining methods. The proposed solution utilizes many of the varied technologies available to the mining engineer for solving mining and underground construction problems. The following are reviewed in the paper: A. The location of the sphere within the dome as required by construction criteria. B. The relation of the location of the access shafts to the sphere. C. The rock mechanics theory in relation to the salt dome and large size of the excavation. D. The proposed "honeycomb" method of mining which will be a partial answer to rock mechanics stability requirements. E. The equipment which it is recommended be utilized to accomplish the construction. F. The rock mechanics measuring instruments proposed. G. The methods of disposal of the mined salt. Conclusions and areas of further study are outlined in the final statement.

Jan 1, 1968

By William W. Adams

The stone-quarrying and related industries of the United States made large gains in employment in 1936 over 1935, according to reports furnished by operating companies to the Bureau of Mines, United States Department of the Interior. Not only were more men employed, but also increases were made in the number of man-days of labor performed and in the number of man-hours worked in 1936. The increase in employment, however, was accompanied by an increase in the number of accidental deaths and injuries among the workers and by a slight increase in the accident-frequency rate per million man-hours worked. The fact that the larger number of accidents resulted in only a slight increase in the accident rate is explained by the large gain made in the number of man-hours worked during 1936. The accident rate in 1936, although higher than in 1935, was the lowest and therefore the best that the industry has experienced in any previous year except 1932 since complete and comparable figures first became available in 1916, a period of 21 years. Operators' reports to the Bureau of Mines showed that the industry as a whole employed an average of 80,022 men in 1936 and that the men worked a total of 18,874,254 man-days or 147,064,448 man-hours. Accidents in and about the plants caused 91 deaths and 5,717 nonfatal lost-time injuries among the workers. The number of injuries and deaths represented an accident-frequency rate of 39.5 per million man-hours worked, compared with a rate of 38.2 in 1935.

Jan 1, 1938

Investigation of standard tests used to establish the decrepitation rating of Western Australian iron ore showed scatter in results which could be reduced by textural type sampling. Testing of individual textural types resulted in separation.of a range of decrepitation behaviour patterns. No unique correlation was established between water content in goethite, or between any single mechanism and breakage in shock heating. The latter depends rather on several mechan- isms whose operation is controlled by the texture of the ore. Texture studies were used successfully to predict decrepitation behaviour which could be related to orebody structure for mine planning, and blending for sales or processing requirements.

Jan 1, 1973

By Robert N. Roby

"The Moffet-Johnston property was investigated by the Bureau of Mines with the object of determining the presence of ore reserves that might be utilized during the war emergency. Preliminary examination was made during May and Juno 1943, as a result of which the Johnston 'tunnel was cleaned out and repaired, the .mime was surveyed, and a small program of exploration was undertaken. This report describes the work performed and presents the data obtained.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts prelimi¬nary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs benefication tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.The chemical and spectrographic analyses were made at Reno, Nov., under the direction of A. C. Rico, acting engineer in charge, Rare and Precious Metals Experiment Station, Bureau of Mines. The ore-dressing tests were under the direction of Rollien R. Wells, metallurgist, at the Salt Lake City laboratories of the Bureau of Mines.The author acknowledges the cooperation and assistance of the lessee of the property, H.R. Hakes, who furnished nine reports and other information.The Moffet-Johnston property is in secs. 2 and 3, T. 3 S., R. 5 W., in the Tidal Wave mining district of Madison County, Montana.The portal of the Johnston adit is near the mouth of Bear Gulch, 9 miles northeast of Twin Bridges, Mont. It is reached by an improved dirt road that serves mining properties farther up Bear Gulch. The Moffet mine and the Mountain View shaft are now accessible from the Bear Gulch road over an access road recently completed by the U. S. Grazing Service. The Grazing Service road has also been supplemented by bulldozer trails built by the Bureau of Mines.An electric-power line extends from the Montana Power Co's substation at Twin Bridges to mines at the head of Bear Gulch and passes within 200 feet of the Johnston portal.The claims of the Moffet-Johnston property were located about 1900. A report by H. V. Winchel, consulting geologist, in 1904 indicates that most of the development on the Johnston adit was completed by that date. At the time of the Winchel report, the Moffet workings had just penetrated the first ore shoot (fig. 4)."

Sep 1, 1946