Search Documents

By Michel Rodrigo Luiz, Glaudistoni da Silva Félix, Osmar Duarte Junior

This article deals with a project to reduce the preparation time and threading the coils in the input section of a pickling line coupled to the cold strip mill (PLTCM) at ArcelorMittal Vega. The project developed serves for the detection and elimination of bottlenecks in the input section. The project was conceived by the philosophy of the Theory of Constraints (TOC) and Lean Six Sigma (6 sigma), here seen as sequencing serial / parallel in the preparation and threading the coils. In this context, a proposal to modify the automatic sequencing and reduction of interruptions due to failure of the automation / equipment confirmed its effectiveness reducing the total time preparation time and threading the coils in the entry section by 15%. This project was developed without investment costs, bringing gains on the order of US$613,769.00.

Oct 1, 2019

By Thomas T., Read

THROUGHOUT the Colonial era, Philadelphia was easily , the leading city of North America, and it still held that position at the end of the period, with a population of about 25,000, though closely pressed by Boston, which had slightly over 20,000, and New York, which had nearly as many. It was the center of a region in which mineral industry was important. Thomas Rutter's bloomery, built in the Schuylkill valley in 1716, was quickly followed by many others, and during the Colonial period at least 20 blast furnaces, 45 forges, and iron- works of other types were built in eastern Pennsylvania, which easily led all the other colonies in iron manufacture. During the Revolutionary period others were erected as far west as Fort Loudon, in the Cumberland c alley.^ After 1800 the rapid development of the anthracite mining industry profoundly affected Philadelphia's, development, since transportation of the coal was then necessarily by water, and the streams of the anthracite . regions mostly flowed into either the Schuylkill or the Delaware Rivers. With an abundant near-by supply of coal and iron, with the seat of government, which had been there since 1774, and with a National Bank established there in 1791, one would have seemed safe in prophesying, at the beginning of the nineteenth century, that Philadelphia would permanently remain the leading city of the United States. Education in Philadelphia was at first wholly in the hands of the Quakers, who had established a "Public School" there in 1689, but in November 1739 George Whitefield, who had created a sensation in England by his preaching, though only 24 years old, passed through Philadelphia on his way to Georgia to found an orphan school there. He preached a series of sermons in Christ Church that were so disturbing to the established church that on Nov. 25 the Rev..Richard Peters (who was also Provincial

Jan 1, 1941

By Thomas B. Dellinger

Since 1950, rotary-drilled, large-diameter holes, "big holes", with depths to over 300 feet and diameters of over 30 inches have become numerous and widespread. Fifty such holes have been drilled for access shafts to LPG mined caverns, Over 70 holes have been drilled for various other commercial activities. Over 150 holes have been drilled by the AEC for atomic testing purposes. These holes have ranged up to 300-inch diameters with 1600-foot depths, 120-inch diameters with 570-foot depths, and 72-inch diameters with 4800-foot depths. Equipment is now available to drill a wide range of ?big holes? for varied requirements. At least a dozen drilling contractors are participating or have participated in the drilling of "big holes". The accompanying tables show pertinent historical, technical and economic data on over 250 holes. The illustrations to be presented concurrently with this paper show the various equipment and accessories now in use. (See Appendix I for captions of illustrations.)

Jan 1, 1966

By James K. Hallenburg

Geophysical borehole logging is a valuable and inexpensive tool for coal deposit evaluation, development, and production. In addition to the usual determinations of depth and seam thickness, geophysical borehole logs can effectively and accurately determine the coal ash, moisture, and heat contents in situ. Location and evaluation of the partings can be done quickly and accurately. Overburden character determination, such as roof competence, dewatering parameters, ripability, trace element content of the coal and overburden, and sulfur content can be done with existing tools and techniques. The quality of such determinations depends upon the quality of planning and calibration.

Jan 1, 1984

By J. M. Galera, M. D. Rodriguez, V. Pozo, S. Cooper

"Cobre Las Cruces mine extracts copper minerals from a VMS deposit located in the well-known Iberian Pyrite Belt (IPB). As an open pit, it is distinguished geologically from other IPB mines by the presence of around 150 m of Tertiary soft marls, known locally as the Guadalquivir Blue Marls, followed by a regionally important aquifer. Below the marls and aquifer the mineralization is hosted by rocks typical of the Palaeozoic within the IPB, comprising gossan, tuffs, slates, and sulphides.This combination of a substantially soft rock and more competent, older (but still occasionally problematic) Palaeozoic lithologies constitutes a unique geological framework and presents substantial challenges in maintenance of slope stability, and therefore operational safety, at the mine site. This paper describes the fundamental design, excavation, and monitoring measures implemented at the mine to maintain safe production, and the lessons learnt during the mine development. IntroductionAs a modern Spanish mine, Las Cruces is committed to the use of best available technology and practices with the aim of guaranteeing the production of ore in a safe environment. From a practical perspective, this implies the realization of a high quality pit design, ongoing geotechnical mapping of exposed slopes to ensure conformity with design, and use of leading geotechnical surveillance technology to complement visual observations. The focus of this article is to illustrate how, at a mine site with potentially problematic soil/rock conditions, multiple advanced techniques employed from design stage analysis through to final pit configuration and vigilance, were combined to achieve an overall control of the ground conditions. In Figure 1 the layout of the pit is shown, illustrating development at the beginning of 2015."

Jul 1, 2019

By Darina Manova

Plasma assisted surface modification methods have been used to nitride stainless steels in order to enhance hardness and therefore the lifetime of industrial components. Nevertheless, the corrosion resistance is not always preserved since it is very sensitive to the process parameters, either in implantation or in thermochemical diffusion techniques. AISI 316L stainless steel was plasma nitrided using three different techniques: Low Energy Ion Implantation (LEII), Plasma Immersion Implantation (PI3) and conventional DC pulsed plasma nitriding (DCPN). For each method several parameters were tested and some of them were selected to achieve the so called S phase of about 3 µm thickness and no nitrides precipitation. The nitrided layer was characterized with OM and SEM. Hardness was assessed on the surface with Vickers indenter and 25 g load. XRD was performed to characterize the S phase and to detect other phases if present and electrochemical corrosion tests were carried out in 3.5% NaCl solution. Although the S phase thickness in the three groups of samples was comparable, hardness was not and neither was the corrosion resistance. The PI3 samples were the hardest with the best performance in corrosion experiments, resulting in a higher breakdown potential and lower currents.

Aug 8, 2018

By Itsuki Uehara, Hiroyuki T. Takeshita, Tetsuo Sakai, Nobuhiro Kuriyama, Hideaki Tanaka

"AB5 type hydrogen storage alloys (A: rare earths, B: transition metals) are extensively applied to a negative electrode of a nickel metal hydride (Ni-MH) rechargeable battery for portable electric equipments, electric vehicles, hybrid vehicles etc. Performance of a hydrogen storage alloy electrode is affected by various factors, microstructure and surface composition of the alloy and structure of the electrode as well as composition of the alloy. Control of those factors enables us to commercialize the Ni-MH battery in various field.IntroductionA Nickel-metal hydride (Ni-MH) battery has been extensively developed because of (1) good compatibility with a nickel cadmium (Ni-Cd) battery, (2) high energy density (1.5-2 times higher per unit volume than a Ni-Cd battery) and high dischargeability, and (3) low environmental pollution. The charge/ discharge reactions can be written as [l, 2,3]:(+) Ni(OH)2+OH- = NiOOH+H2O+e· (E=+0.490V NHE),(-) l/6LaNi5+H2O+e-· = 1/6LaNi5H6+OH- (E=-0.828V NHE),where E° is a standard potential of an electrode vs. normal hydrogen electrode (NHE). Because of the above advantages of a Ni-MH battery, the battery have been widely used as a power source of portable computers, cellular phones, electric vehicles (Toyota ""LAV4L EV"", Honda ""EV Plus"" etc.) etc. Some hybride vehicles (Toyota ""Prius"" and Honda ""INSIGHT"") and fuel cell vhehicles (Toyota ""FCEV"") are power-assisted by a high-power Ni-MH battery. In 1999, the production of Ni-MH batteries reached 870 million cells in Japan. Most of commercialized NiMH batteries are incorporated with rare-earth-based AB5-type hydrogen storage alloy as a negative_ electrode. The production of rare-earth-based alloy is estimated to be approximately 8000 tons.The battery performances of the Ni-MH battery, for example, capacity, durability (cycle life), dischargeability (kinetics) and selfdischarge, ate closely related to the metal hydride· (MH) electrode, especially, the hydrogen storage alloy in the electrode. Substitution of alloy components, heat treatment, and surface treatment in order to change surface and bulk structure of hydrogen storage alloys have been examined by us and many reseachers in order to improve the performances of MH electrodes. This paper is a review of our and their efforts to improve performances of MH electrodes."

Jan 1, 2000

By L. A. Haas

The Bureau of Mines conducted bench-scale leaching tests with recycled spent copper electrolytes and copper-nickel mattes produced from the Minnesota Duluth Complex concentrates. This report describes the first stage of an overall two-stage leach operation. The objective of this research was to determine the matte-leach technology required to convert spent copper electrolyte into an enriched nickel liquor suitable for a nickel refinery and there-fore essentially free of copper, iron, and sulfuric acid. The experimental variables investigated were matte composition, particle size, spent electrolyte content, pulp concentration, oxygenation, temperature, and time. The time required to produce an enriched purified nickel liquor decreased with increasing pulp concentration, temperature, and oxygenation, but increased with increasing particle size and electrolyte copper and acid content. Nickel-rich (about 50 g/l) liquors at a pH of about 4 and containing less than 1 g/l of copper and iron were produced at 70° C by leaching minus 325-mesh low-iron (less than 5 pct) matte for 8 hours with spent electrolyte containing 22.4 g/l Cu, 28.9 g/l Ni, less than 0.1 g/l Fe, and 50 g/l H2S04 at a pulp concentration of 1 kg of matte per liter of spent electrolyteo Varying the nickel content of the spent electrolyte from 11 to 101 g/l appeared to have no appreciable influence on the matte leaching characteristics.

Jan 1, 1981

By Steven J. Page, Wm. Randolph “Randy” Reed, John A. Organiscak

Researchers studying dust generation from blasthole drills developed a simple, quick fix that reduced respirable dust concentrations by more than 63% at the dump point. This device, which requires almost no maintenance, is small and inexpensive, and it will help operators maintain compliance to the dust standard. The thought process was that a reduction of respirable dust at any of the multiple sources on the drill, in this case the dust collector dump point, should reduce the total respirable dust generated by the drill. The U.S. Mine Safety & Health Administration (MSHA) has a coal respirable dust standard of 2 milligrams per cubic meter (mg/m3) for an 8-hour shift. MSHA and mine operators periodically collect personal dust samples to determine compliance with this dust standard. Drill operators have one of the highest exposure levels to respirable dust. This has been proven through many reviews of the MSHA dust sampling database. Prior to 1987, the highwall driller at surface coal mines had the most severe exposure to respirable silica dust, a trend that continues today based on MSHA's respirable dust sampling database. A review of the MSHA database for the years 1985 through 1992 shows that 81% of the respirable silica dust samples taken exceeded the permissible exposure limit for the highwall drill operator at surface coal mines. A more recent review of the MSHA database, for the years 1996 through 2000, shows that only 31% of the respirable silica dust samples taken exceeded the respirable silica dust limit for the highwall driller at surface coal mines. This suggests a substantial improvement in preventing the exposure of silica dust to the highwall drill operator. The drill operator, however, still tops the list of job occupations that have the highest exposure to respirable silica dust Respirable dust has been shown to be harmful to human health, especially when silica is present in the dust. It causes a disease known as silicosis, which can occur in three levels: chronic silicosis, which occurs after 10 years of exposure; accelerated silicosis, which occurs between 5 and 10 years of exposure; and acute silicosis, which can occur within a few weeks to five years of very high exposure to silica dust. Respirable dust consists of the dust particle size fraction whose median diameter is 4 micrometers (µm). The drilling machine generates high concentrations of respirable dust from several sources: drill table shroud leakage, dust leakage through the table bushing, dust discharge from the dust collector exhaust due to impaired filters, and dust entrained from the dust collector fines dumped onto the bench. The National Institute for Occupational Safety and Health's (NIOSH) Pittsburgh Research Lab (PRL) has been studying different methods to reduce respirable dust from these sources. During its testing, the institute identified a simple solution that reduces the amount of respirable dust generated at the collector dump point.

By D. P. Bryan

The identification and-develop¬ment of new construction aggregate resources, the most common mineral mined, is an essential need in this country's growing urban areas. In developing an aggregate exploration program, a thorough geological identification of all potential aggregate resources in an area is still of primary importance but other factors have also to be considered. These include physical properties, end product application, transportation and mining costs, and local government regulations including zoning. The present major aggregate producers are most likely to develop these future resources and are in the best position to initiate comprehensive exploration programs.

Jan 1, 1987

By J. L. Bruce, G. W. Nicolson

THE country rock of the Mavrovouni mine of the Cyprus Mines Corp. is hydrothermally altered, disintegrated pillow lava, with very little tensile strength ("short" ground). In places, especially when wet, it is heavy ground, though not extremely heavy except where movement has been caused by underlying or nearby stoping operations. Damage by caving from roof or sides of galleries is not sudden but progressively faster when the size of the cave increases as a result of the fall of small pieces. CEMENT AND CONCRETE LININGS During early operations, galleries in the country rock were supported by customary mine-timbering methods. Available timber, however, was of poor quality and of relatively high price, and replacements were frequent and expensive. Furthermore, the massive sulphide ore bodies required large volumes of fresh air for ventilation and cooling, and it was therefore desirable to provide smooth-lined galleries with low resistance for the introduction of air to the ore bodies. It was also desirable to eliminate hazards of fire in shafts and underground workings insofar as this would be practical. Cement and concrete were relatively cheap, and plans for using these in support of shafts, underground galleries, raises, and chutes, were developed steadily. Circular shafts with diameters ranging from 10 to 15 ft were adopted for all permanent shafts and airways. In places these were lined with concrete poured behind sectional pressed-steel forms especially constructed for this purpose. In other places, they were lined with precast-concrete blocks. It was found that such precast concrete of good quality could be produced on mass production scale and delivered at the mine from most favorable point of manufacture, at a cost of about 25 cents per cubic foot of concrete. This refers to prewar costs. As the use of concrete blocks in circular lined galleries was developed, it was found that there were very great advantages in the reduction of air resistance as compared with customary timber supports. After best methods had been developed, it was found that breakage and replacements were extraordinarily low, averaging only about 1 ½ pct per year during a period of about 15 years. Furthermore, it has been possible to reclaim for re-use a very large percentage of the concrete blocks from abandoned galleries. During the history of the operations precast-concrete blocks have been used for lining shafts, raises, ore chutes, galleries, and shaft stations, ranging from 3 to 16 ft id. The thickness of lining has varied from 5 to 10 in.; with I2 in. thickness in a few cases. Junctions of two galleries at angles ranging from about 30 to 60° are usually made of poured concrete behind sectional forms, or of a combination of poured concrete and precast blocks. In nearly all cases it has been found advisable to make the point of the wedge at the junction, of

Jan 1, 1947

By Immo H. Redeker

Introduction In October of 1961 Texas Gulf Sulphur Company contacted the Asheville Minerals Research Laboratory, of the North Carolina State University, and requested assistance in the development of a phosphate ore body in Beaufort County. The main: objectives of the work at Asheville were defined as follows. The Laboratory should try to determine on the basis of drill core samples, submitted by Texas Gulf Sulphur Company, the highest grade of phosphate concentrate that could be obtained with high recoveries from North Carolina ore, the thickness of the ore body that could be treated economically in one section, and the quantity of concentrate that could be obtained per acre. The results should be compared with data obtained from the treatment of Florida ores. It was important to use mineral preparation methods during the initial laboratory work that could be verified later by continuous pilot plant operation and could be scaled-up for a commercial plant. The writer was in charge of the project at the Asheville Minerals Research Laboratory and participated in the development of one of North Carolina's greatest mineral resources from the first drill core examination to the production of the first poundage and tonnage quantities of flotation concentrates. The Lee Creek phosphate mine and mill was put in operation in early 1966 and can produce three million tons of phosphate concentrate a year. Sulfuric- acid, and phosphoric acid plant, diamonium phosphate plant and triple super phosphate plants came on stream in 1967; at that time they were the world's largest. Now that a phosphate industry has been established in the State, it]

Jan 1, 1971

By M. Wrobel, J. Hammerschmidt, M. Runkel

Fluid-bed technology is a key pyrometallurgical step for processing a vast number of ores and concentrates. Over the past 50 years, considerable research and development efforts have been made by Metso Outotec to expand the application window of this technology. This paper illustrates different processing routes where fluid-bed technology plays an important role in the production of the copper. The fluid-bed processes utilized are partial, sulfate-producing, and dead roasting. The focus of this paper considers the advantages of the dead-roasting process. This “zero waste” process can provide copper oxides, steam, electrical power, and sulfuric acid for new and existing solvent extraction–electrowinning plants. In a case where an operation is running out of oxidic ores and concentrates, fluid-bed roasting can be applied to close this gap and provide the required copper oxides in a sustainable way.

Jan 1, 2023

By GERALD A. WARING

ALASKA'S coal consumption is now about 130,000 tons annually. About one-quarter of this amount is used in the southeastern part of the territory and in settlements on the western coast and comes from Seattle and from British Columbia mines. About 60,000 tons is sub-bituminous coal from the Healy River mine in central Alaska, and is used mainly at Fairbanks, sixty miles to the north, for heating and the development of electric energy, for the city and the gold-dredging operations of the Fairbanks Exploration Co. The remaining 40,000 or 50,000 tons is bituminous coal from Matanuska Valley, in the south-central part of the territory. These coal deposits extend intermittently for about forty miles along the valley, which trends eastward from the upper end of Cook Inlet.

Jan 1, 1934

By Michael J. Magyar

This report contains a cost estimate of the Bureau of Mines process for dewatering Alaskan placer effluent streams with polyethylene oxide (PEO). In this process effluent slurry is withdrawn from the placer plant pond system after a primary settling stage. A dilute PEO solution is injected into the slurry line to flocculate the fine, suspended solids. The flocculated solids are dewatered on a stationary screen. Clarified water is returned to the placer operation or discharged, while the 35 percent solids waste is pumped back into the mine cut. Cost estimates are presented for dewatering plants processing 1,000 gallons per minute of effluent slurry at three representative turbidity levels. Both the placer and the dewatering plants operate on the same 1-shift-per-day, 6-day-per-week schedule for the 100-day Alaskan operating season. Estimated fixed capital costs for these plants processing placer with effluent turbidities of 1,000, 3,000, and 5,000 nephelometric turbidity units (NTU) are approximately $29,000, $31,000, and $34,000, respectively, on a fourth quarter 1986 basis. Operating costs are estimated to be $0.34, $0.37, and $0.40 per thousand gallons of effluent slurry.

Jan 1, 1987

By C. Musingwini, A. S. Nhleko, P. M. Muke

Open-pit mine planning includes the determination of a long-term open-pit mine production scheduling (OMPS) plan. The OMPS plan is generally a three-dimensional (3D) block extraction sequence that seeks to maximise the net present value (NPV) of future cash flows, while complying with technical and operational constraints. The OMPS problem is computationally complex because it involves the analysis of large datasets, while simultaneously incorporating both multiple hard and soft constraints. The OMPS problem has been solved using deterministic or exact approaches, heuristic, and metaheuristic models. When compared to heuristic and metaheuristic models, deterministic approaches tend to take much longer to solve the OMPS problem when the number of constraints increases. Therefore, this paper presents a metaheuristic model which utilises a genetic algorithm (GA) framework to solve the OMPS problem. The GA-based model was applied to the Newman1 and Zuck Small mining instances, which are publicly available from the online MineLib database. The NPVs for the OMPS plan generated using the GA-based model for the two case studies were compared to the best-known published MineLib solutions obtained using the TopoSort heuristic model at the time of this study. For the Newman1 instance the equivalent annual NPVs were approximately US$6.6 million for the GA-based solution and US$5.1 million for the TopoSort solution. For the Zuck Small mining instance, the equivalent annual NPVs were approximately US$99.8 million for the GA-based solution and US$102.5 mil for the TopoSort solution. These results show that the GA-based model produced comparable solutions to some of the best-known solutions, thus, indicating strong potential application of GA-based models to solve OMPS problems.

Sep 1, 2021

By S. C. Gaillard

Tailings are made of ground rock that is left over from removing valuable minerals. The tailings are usually fine particles that cause environmental issues for storage and disposal. Disposal of tailings is a growing concern, as more tailings are produced from the increasing demand for mined material (ITRC, 2008). This project proposes a way to convert the mine waste to a useful product. Tailings were selected from a South Carolina crushed stone quarry, the products of which are used for road beds, sidewalks, asphalt and driveways. These tailings were processed to generate synthetic aggregates for construction applications. The synthetic aggregate creates a product that could be used for many purposes, including aggregate for sidewalks, driveways, roads and building materials. Testing methods followed the North Carolina Department of Transportation (NCDOT) guidelines for physical testing of coarse natural aggregate, which are sieve analysis, Los Angeles abrasion, absorption, specific gravity and soundness test. The synthetic aggregate produced passed all tests for NCDOT and, in some instances, rated better than a natural aggregate. Using the tailings from the crushed stone and mining industry would convert the waste into a valuable, marketable product.

Jan 1, 2013

La presente investigación revela aspectos sobre los métodos geoquímicos aplicados a la exploración de depósitos minerales, como las aplicaciones prácticas e indicaciones sobre de las diversas técnicas empleadas en el campo y y laboratorio. La exploración química de los depósitos minerales como método de prospección, comprende la investigación e interpretación de anomalías químicas relacionadas a la mineralización dentro de varias sustancias naturales como rocas, aguas y vegetación para así localizar depósitos minerales ocultos. La naturaleza de estas anomalías se divide en dos grupos: las anomalías primarias formadas durante el periodo de mineralización y las secundarias, formadas por la destrucción y dispersión del depósito metalífero durante el ciclo de intemperismo y erosión. Sin embargo, existen algunas anomalías de naturaleza "residual" o "vestigial", las cuales son descubiertas mediante el muestreo sistemático de rocas o de los suelos que de ellas derivan. A esto se suma, la dispersión de elementos en solución puede dar origen a muchas variedades de anomalías secundarias que tienen importancia en la exploración geoquímica como las dispersiones secundarias en las aguas de fuentes, pozos y aguas corrientes, en las cajas de cuerpos mineralizados; en coberturas de carácter no residual sobre y cerca de depósitos mineralizados y aquellas dispersiones secundarias en vegetales. Paralelamente a esta exploración geoquímica, tenemos otras métodos comom los técnicas colorimétricas, basadas en reactivos que indican cambios de color y los de análisis espectográfico, que complementan paulatinamente dicho proceso minerológico.

Jul 20, 1956

By Wenbin Liu

A novel route for rapid synthesis of ultrafine WC-Co cemented carbides with homogeneous binder phase distribution is reported. The composite powder is produced by in situ reduction-carbonization reactions by using WO2.9, Co3O4 and carbon black as raw powders. The reaction equilibrium and phase stability are studied by thermodynamic calculations. The WC-Co composite powder is condensed by spark plasma sintering (SPS) to obtain the cemented carbides bulk. The sintering temperature is lower than that in the conventional sintering methods by 1500C, while the sintering time is remarkably reduced by 3-5 times. The high performances of the hardness and the fracture toughness are obtained. The experimental results confirm that the present processing scheme of in situ reduction-carbonization reactions and subsequent SPS sintering is an efficient way to prepare WC-Co cemented carbides, and is apparently superior to the conventional long-period techniques of preparing composite powder and cemented carbides bulk.

Jan 1, 2008

By Mao Chen, Baojun Zhao, Zhixiang Cui

Bottom blown oxygen copper smelting process, operated at high grade matte (up to 75 wt% Cu) with relatively low (2-3 wt%) Cu in slag, has been commercialized for more than five years at Dongying Fangyuan Nonferrous Metals CO., Ltd. Quenched slag and matte samples have been collected at different operating conditions while the slag temperature was measured by thermocouple. The samples were analysed by X-ray Fluorescence and Electron Probe X-ray Microanalysis. FactSage computational software was used to explain the observations of the industrial samples. The analyses show that the copper loss was closely related to the operation parameters. The Fe/SiO2 in slag and temperature determine the solid proportion, which significantly affects the physical entrained and also chemically dissolved copper in the slag. The present study will be useful in understanding the slag chemistry of bottom blown copper smelting furnace and in optimization of the operating conditions to lower Cu loss in the slag.

Jan 1, 2015