Search Documents

By George M. McArthur

General Statement In Montana, as in most states, the requirements for water quality control are becoming more restrictive. What was once accepted practice is now obsolete. The planning and construction of water quality control facilities has taken on new importance. Past practices and new ideas must be examined to meet the challenge. By this paper we hope to encourage the exchange of ideas for the improvement of water quality control techniques. Both the mining industry and governmental agencies should benefit from such an exchange. The following is a summary of the work done and in progress by The Anaconda Company in Butte to provide an improved water quality related to production processes. We invite your comments. Acknowledgements This paper would not have been possible without the efforts of many individuals and departments in The Anaconda Company, including the Environmental Engineering Department, Mr. Frank J. Laird, Director; Montana Operations, Mr. M. K. Hannifan, General Manager, and their assistants.

Jan 1, 1972

By Brian Danyliw

"Dust control is an increasingly important consideration for all mining operations from a health, safety, environmental and maintenance perspective. Modern mining operations incorporate a variety of mechanical dust control techniques into design however in many cases these engineered systems are unable to meet desired fugitive dust level targets. In these cases a variety of chemical dust suppression options are available to operators to assist in meeting their targets. This paper provides an overview of available chemistries, discussion of application techniques and equipment requirements and available performance monitoring technologies. This paper will also include a number of case histories discussing the treatment approach chosen, challenges encountered, chemical feed, storage and application equipment, monitoring techniques employed and results achieved.INTRODUCTIONDust FundamentalsFugitive dust by definition is an aerosol consisting of particulate matter suspended in a gaseous medium. Aerosols can include suspensions of particulate (solids) or sprays (liquids) or a mixture of both. Of particular concern from an occupational health and safety perspective are aerosols of particulate matter due to their involvement in classical occupations lung diseases such as silicosis, poisoning through chronic exposure to compounds such as lead and beryllium and expected involvement in more modern identified conditions such as cancer, asthma, and a host of other respiratory and non-respiratory conditions which may be caused or influenced through exposure to dust.According to the ""Glossary of Atmospheric Chemistry Terms"" (IUPAC, 1990), ""Dust: Small, dry, solid particles projected into the air by natural forces, such as wind, volcanic eruption, and by mechanical or man-made processes such as crushing, grinding, milling, drilling, demolition, shoveling, conveying, screening, bagging, and sweeping. Dust particles are usually in the size range from about 1 to 100 µm in diameter, and they settle slowly under the influence of gravity."" It should be noted that the behavior of particulates with respect to settling rate in air is a function of particle mass and shape and therefore the geometric size of the particle can be misleading. Occupational hygienists utilize the concept of particle aerodynamic diameter as a more representative reflection of particle size. Particle aerodynamic diameter, is defined as ""the diameter of a hypothetical sphere of density 1 g/cm3 having the same terminal settling velocity in calm air as the particle in question, regardless of its geometric size, shape and true density."" The expression of particle size as aerodynamic diameter allows for a more consistent understanding of particle behavior both from a settling perspective as well as from the perspective of how dust particles will behave in the respiratory tract. Figure 1 illustrates settling rates for particles of various aerodynamic diameters. The relationship between particle size and settling rate is important for understanding what size of particles must be addressed by dust control strategies as well as what particle sizes represent the most danger from an exposure and occupational health perspective."

Jan 1, 2015

By C Young

The identification of Critical Risks, their associated Critical Controls, and the implementation of processes to ensure their ongoing management can be difficult and resource intensive. Answering the following Critical Risk Management related questions can be challenging: • What is a Critical Risk? • What is a Bow-tie Analysis and when should it be used? • What is Critical Control? • How is the effectiveness of a Critical Control assured, and how is this measured? • Who is responsible for managing Critical Controls? • What are the implications if a Critical Control is not effective? It appears that in the mining industry’s efforts to implement the Critical Control Management Process outlined by the International Council on Mining and Metals (ICMM), instead of embedding an integrated, well understood, value adding process, we have instead created a resource hungry monster that is poorly understood by numerous layers of the organisation.

May 5, 2022

By D. Silva-Galvan, R. D. Morales, S. Gonzáelez-López, A. Romero-Serrano, G. Plascencia-Barrera, F. Chavez-Alcala

This work is focussed on lead decopperising by two techniques: conventional top addition of sulfur and injection of sulfur powder. It is found that the first method proceeds under equilibrium conditions and the second one depends on kinetic considerations. Experiments were carried out using 15 kg lead baths at two temperatures, 340°C and 380°C. The carrying gas used for the injection trials was nitrogen at flow rates of 6.3 and 18.6 L min- 1• The results show that 'decopperising process is more efficient at temperatures close to the melting point of lead for the sulfur top addition process, whereas high temperatures produce better copper removal for the injection of sulfur powder. Besides, the sulfur injection with the higher nitrogen flow rate (18.6 L min-1) produced higher decopperising rates. Thermodynamic and kinetic models are used to simulate this lead refining process.

Jan 1, 2000

Alfred C. Young† (communication to the Secretary): Before the appearance of Mr. Scott's paper in these Transactions we were not specially interested in the investigation which he has started; but at his request we have endeavored to collect from musty records and the recollection of our old friends a brief chronicle of the progress made by this house. As 3000 instruments were manufactured by us before any descriptive record was kept, and 2000 more before the record contained more than a statement whether the instrument was a transit or a level, and sometimes its size, we approach the task with timidity, trusting that the reader will bear the difficulties in mind, particularly as the writer's predecessors, from whom, no doubt, the information desired could have been obtained, have passed away. Instruments for surveying were manufactured by David Rittenhouse, of Philadelphia, as early as 1760; but it was not until late in the first quarter of this century that there was any American market for an instrument outside of the ordinary surveyor's compass. With the advent of canals and railroads, and the more extensive development of the Pennsylvania coalfields, arose a demand for surveying-instruments to meet problems in engineering beyond the limited field of the compass. On May 1, 1820, in which year the practical mining of anthracite coal in Pennsylvania began, William J. Young, who had served his apprenticeship with one Thomas Whitney,

Jan 1, 1901

By Yves Breau, François Robichaud, Jacques McMullen, Pierre Pelletie

"The Expert System implemented at the East-Malartic mill controls a copper flotation circuit while taking into account the profitability of the operation. Treating a copper gold ore, the flow sheet integrates a flotation step followed by cyanide leach circuit. The Expert System calculates the actual net smelter revenue of the flotation circuit, accounts for the operating cost of the cyanidation circuit and defines optimal metallurgical operating targets to optimize the overall economics. To be realistic, probability factors and circuit diagnostic analysis are integrated in the operating target selection. The Expert System has proved to be successful, robust and flexible. It resulted in a copper concentrate grade increase of 1% while maintaining recovery. The use of the expert system also gives plant personnel good training procedures and promotes interaction with mill operator.INTRODUCTIONThe East-Malartic mill is located close to the town of Malartic in North Western Quebec, Canada. The mill was first commissioned in 1938. The flowsheet at that time was a straight cyanidation circuit. The original mill operated in that mode up to the discovery of the Bousquet 2 orebody in 1989 which consisted of a massive copper sulphide ore averaging 0.7% copper and 7 g/mt of gold. Bousquet 2 ore processing required a mill retrofit. Grinding capacity, gravity and copper flotation circuits were inserted prior to the cyanidation circuit in order to achieve 3,200 mtpd capacity at expected recoveries.In 1993, control of the flotation circuit was deemed critical in order to maintain the flotation performance and to reduce cyanide consumption since the copper sulphide contained in the Bousquet 2 ore is a high cyanide consumer (50% bornite). (McMullen, 1999) As a result, the implementation of advanced control strategies in order to increase the metallurgical profitability of the plant and to reduce the operating variability between operators was the most rational alternative. In 1994, Corem was chosen to perform the plant audit and to write the first set of rules. The on-line control strategy was started up in 1995. In 1996 and 1997 the Expert System was shutdown because of an extreme change in the ore coming from the milling of Bousquet #1 ore and the departure of the projects engineer. In 1998, the system was restarted and the results were impressive. Furthermore in May of 2001 a patent was issued for the control strategy. (Breau, 2001)"

Jan 1, 2002

By D. L. Nussear, W. E. Wallace, N. Clark, M. Gautaum, G. Hong-Guang

"Results of a research effort directed towards identifying and measuring the genotoxic properties of respirable particulate matter involved in mining exposures, especially those which may synergistically affect genotoxic hazard, are presented. Particulate matter emissions from a direct injection diesel engine have been sampled and assayed to determine the genotoxic potential as a function of engine operating conditions. Diesel exhaust from a caterpillar 3304 diesel engine, representative of the ones found in underground mines, rated 100 hp at 2200 rpm is diluted in a multi-tube mini-dilution tunnel and the particulate matter is collected on 70 mm fluorocarbon coated glass fiber filters as well as on S"" x 10"" hi-volume filters. A six mode steady state duty cycle was used to relate engine operating conditions to the genotoxic potential. Results to-date on diesel exhaust have indicated that use of a primary component of pulmonary surfactant as a medium for collecting and applying respirable particulate material to cells for mutagenicity testing offers a true representation of in-vivo delivery of such respired aerosols to pulmonary cells and the genetic material within. Protocols have been developed to sample and assay the diesel soot and diesel soot/mineral dust complexes which would not compromise the surf ace and physical properties of the particulate material. Evidence has been gathered to show that diesel soot expresses mutagenic potential as dispersions in DPL in the Ames tests as well as sister chromatid exchange activity in the animal lung fibroblast ·derived V79 cell line. The results are comparable to the standard solvent extraction procedure. INTRODUCTIONDiesel engines are primarily associated with transportation; however, they are also very common in the work place. Of particular concern is the use of diesel engines in mining operations. Currently there are 1,950 diesel machines working in underground coal mines throughout the country. These units are used in 151 mines encompassing nine different states (MSHA, 1991). It is believed the use of diesel powered equipment has contributed to higher productivity in these mines. However, the exhaust from diesel engines operated in underground mines has been a subject of concern during the past decade because of its suspected relationship with health aspects. The particulate matter generated by the diesel engine is of particular concern."

Mar 1, 1992

By Chetan P. Malhotra

This paper describes an online control system and simulation environment for reheating furnaces. The system can be configured for implementing manual control as well as automatic control using either look-up tables or online model predictions. The simulator is also used for offline generation of optimized normal operation and delay setpoints for look-up tables and generating ideal heating curves for model-based control. Finally, it is employed to compare the performance of the above control strategies over a typical period of operation of a pusher-type reheating furnace. Keywords: Reheating furnace, control strategy, model-based control

Jan 1, 2003

By B. M. Larsen

NEVER having actually tried to engage in the systematic education of anyone, and having little direct knowledge of the practical problems and limitations in the field of education, I can pose only as a "nonexpert" in this field, one whose ideas are to be regarded as personal opinions. The necessity for compromise between educational ideals and the practical limitations of time, money, and mental capacities of both student and teacher is evident in the preparation of an end product that we may regard with a reasonable degree of conviction as a professional engineer. We need to do so many things. The engineering student must have a clear understanding of the basic sciences; he should develop manual skills and co-ordination; he should speak and write the language with simple clarity and directness; he should gather knowledge of a special field; and, he should be educated for living in a broad ..

Jan 1, 1948

By Rafael Moure

On April 21, 1980 the Oil, Chemical and Atomic Workers Union (OCAW) submitted a petition urging the revision of the Mine Safety and Health Administration (MSHA) permissible exposure limit to radon daughters in underground mines. This petition asks for: 1. Annual worker exposure to be lowered from the current 4 WLM/year to 0.7 WLM/year; 2. Full economic protection for workers whose exposure exceeds the proposed 0.7 WLM/ year; and 3. The primary means of lowering workers' radiation exposures shall be environmental controls. I will present the scientific rationale for the lower standard requested in our petition to the Department of Labor. [1. Radiation Exposures to Uranium Miners] Two types of radiation exposures are present in the environment of uranium mines: A. [External Exposure] to gamma sources which until 1978 was considered as negligible compared with internal alpha radiation. R. E. Utting (1), in an investigation of three Canadian uranium mines, found levels of exposures adding to an annual dose equivalent of 3 rems (30 mSv)/year. He concluded that gamma dosages may be a major fraction of the maximum permissible dose for many individual miners. The U.S. experience has shown that there is significant gamma exposure in U.S. uranium mines and, therefore, it could contribute to the total radiation exposure to the lungs in combination with internal alpha radiation. Before ventilation improvements in uranium mines, the contribution of external radiation to total lung dosage was relatively small. After improvements in ventilation, the reduction in internal radiation exposure appears to be in 1980 as low as 1/10 of the 1950 dosages. However, ventilation improvements do not affect external gamma radiation. Gamma radiation remains at the same 1950's level, and it represents today a higher proportion of the total radiation burden to the miner's lungs. MSHA regulations (57.5-47) state that if gamma exposure is below 2.0 milliroentgens per hour, then workers are not required to wear gamma dosimeters and cummulative gamma radiation records need not be kept. Assuming an exposure of 1.9 milliroentgens per hour per 173 hours/month for 12 months,a miner would accumulate a dose from external radiation of 3.9 rems/ year. This dosage would, of course, go unrecorded. MSHA, therefore, should consider a downward revision of the external radiation permissible exposure limit of 2.0 milliroentgens/hour. MSHA should make clear that this exposure level, when added to the internal exposure, does not make for sound health physics -even though the measured current levels do not approach 2.0 milliroentgens/hour. B. [Internal Exposure] to alpha radiation is still the larger contributor to lung irradiation in uranium miners. The target organ is still the lung. The parameters to be considered in determining the biological radiation load appear in Table I for radon daughters present in the upper respiratory tract (URT). TABLE I RADIATION DOSE PARAMETERS IN THE URT OF URANIUM MINERS Parameter Uranium Underground Mining [1. Quantity of the Absorbed Radon daughters (Po-218, Nuclide Pb-214, Bi-214) deposit in bronchial and lung tissue. (Measured by air concentration, Working Levels) 2. Type of Radiation Emitted Alpha Particles 3. Energy of Radiation High-Linear Energy Transfer 4. Half-life of the Nuclide Ra 222, 3.8 days in the Organ Po-218 (RaA), T1/2 = 3.1 minutes Pb-214 (RaB), T1/2 = 26.8 minutes Bi-264 (RaC), Vi = 19.7 minutes 5. Selection Factor of the Direct inhalation with mine Organ dust to be deposited in the tipper Respiratory Tract 6. Mass and Form of the Organ Especially cancer sensitive, tracheobronchial region and bronchi* 7. Distribution of the Activity Dependent on deposited dust in the Organ distribution in the Upper Respiratory Tract 8. Chemical Nature of All compounds (RaA, RaB, RaC) Incorporated Substance biologically insoluble. (Only localized, irradiation) *See Reference (2)] The parameters of Table I depend, in turn, on the demography of the exposed population, especially: 1. Age 2. Sex 3. Health Status 4. Genetic Constitution 5. Lifestyle (Smoking, Diet) Some of these demographic characteristics of uran-

Jan 1, 1981

By C. W. Davis

This is the first of a series of papers being; prepared as the work progresses in a study of the hydrometallurgy of manganese. The investigation is being made in an endeavor to make possible the utilization of lour-grade domestic manganese ores. The value of a hydrometallurgical process for manganese depends on the present and future uses for manganese products.

Jan 1, 1930

By George W. Healy

The direct retorting of zinc sulfide concentrates in the presence of lime and carbon was examined on a laboratory scale with ten-gram charges of loose mix or fifteen-gram ones of pellets. A slow stream of nitrogen swept through the furnace tube over the boat of reactants, carrying with it the zinc vapor, which condensed on a rolled-up steel sheet near the exit, permitting weight of zinc produced to be obtained after completion of a run. Variables explored were percent of theoretical reagents, temperature, and time. During the runs gas samples were analysed periodically, and the content of CO2, CO and nitrogen were obtained. The quantities of the carbon gases could be calculated because the nitogen flow rate was measured. The gases were also examined for sulfur species, but neither COS nor SO2 could be detected at maximum sensitivity. Zinc recovery increased with excess carbon and lime and with temperature. It ranged from 77% at a ten percent deficiency to 90% at a ten percent excess at 1100°C. Going to 1200°C and theoretical reagents gave 93% recovery. Increasing time from 200 minutes to 300 minutes increased zinc yield by up to 10%. Results from sphalerite and a commercial concentrate from AMAX gave generally similar results. The reaction rate of zinc sulfide as sphalerite and of calcined sphalerite indicated that the latter reacted almost twice as fast, and recovery of zinc was five percent higher. Though the retorting step using sulfide, lime, and carbon proved to be non-polluting, it was feared that on storage the calcium sulfide in the residues would decompose, giving off noxious gases. Consequently the stabilization of the residues by oxidation was essayed. Because of the presence of unreacted zinc sulfide, the first product of oxidation was S02. Reaction of CaS to CaSO4 was incomplete, going from 20% at 800°C to 90% at 1200°C. Thus the non-polluting nature of the process as a whole is in doubt, and its economics are likely to be unfavorable compared to the traditional way of calcining the concentrates, followed by retorting of the oxide with carbon.

Jan 1, 1982

There has been disappointingly little development in the analysis of rock slopes in open pit mines over the past 30 years. A brief review of literature shows that the application of numerical stress analysis methods to open pit mine slope stability has become only relatively common in recent times, and that there are as yet no standardized approaches. The lack of development in general, and of robust, standardized approaches in particular, is surprising in view of the ?ultra? deep open pit mines that are being developed to depths in excess of 1000 m. In this paper, the results of a substantial programme of two dimensional and axisymmetric analyses of open pit slopes are described. Variations in the following parameters were taken into account in this programme: slope angle, slope height and horizontal to vertical in situ stress ratio. The evaluation of the data has concentrated on the tensile stresses and the extension strains in the slopes. This is believed to be the first publication dealing with strain distributions in slopes. The occurrence of zones of tensile stress was very limited. These zones occur in the crests of slopes, except in the case of low horizontal to vertical stress ratios, in which case the tensile zone is in the floor of the pit. In contrast, very large zones of extension strain can occur, and this finding represents a significant new aspect in slope stability that has not been considered before. The greatest magnitudes of extension strain occur near the toe of the slope, either in the slope itself, or in the floor of the pit. The magnitudes of the strains are considered to be large enough to result in fracturing of intact rock, and the fracture orientations predicted are adverse for slope stability. The large zone in which such extension failure could potentially occur in a 1200 m deep pit is typically more than 100 m horizontally behind the toe and about 400 m up the face from the toe. Fracturing that is extension in nature is common in competent, brittle rocks and often develops with some violence and little or no warning. Such ?strain bursting? produces easily measurable seismicity, events often being audible as well. In the slope situation, the expected physical manifestation of this behaviour would be popping off of rock slabs and plates of rock from slope surfaces and popping up of the pit floor, as well as the formation of new fractures within the rock mass. Such behaviour may cause overall slope failure, or may initiate failure, which may then be driven to overall slope failure by other influencing factors or combinations of factors. In addition to instability resulting from the fracture surfaces themselves, all induced fracture surfaces could interact with natural geological structures to facilitate formation of a significant failure surface. With suitably orientated joints, extension strains are likely to manifest themselves in the opening up of such joints and hence in the loosening of the rock mass in a preferential orientation, with potential effects on groundwater flow patterns.

Jan 1, 2003

By J. T. Ryan

SiR Humphry Davy's epoch-making treatise delivered on Nov. 9, 1815, before the Philosophical Society of London, first announced and demonstrated a flame safety lamp for detecting methane in mine air. Coal mining was known in England as early as 1180, more than 600 years before the advent of a safe lighting and gas-detecting appliance. Mining, no doubt, took place first in outcrop coal, and danger from gas did not become apparent until the workings became deeper and more extensive. Davy's lamp did much to increase the safety of miners, and a modified Davy lamp is still widely used for detecting the presence and approximate amount of combustible gas in mine air. No factor in coal mining has improved more rapidly during the past 15 years than safety measures. This progress came about not only as a result of the workmen's compensation laws now in force in most of the states of the Union, but because the research work of the U. S. Bureau of Mines had demonstrated some dangers incident to coal mining which were not considered to be serious matters prior to that time. Electric power and explosives are necessary but potential hazards in American coal mines. A general mechanization program is now under way, while the mines are growing deeper and more extensive. Consequently ventilation problems are more complex and a demand has been created for positive detecting devices for carbon monoxide as well as methane. Scientists and manufacturers, working hand in hand during the past 10 years, have invented and developed appliances which make systematic and effective examination of mine air possible. The object of this paper is to describe briefly the approved testing devices in use today, with the hope that they may lead to the saving of life. Two Groups of Dangerous Coal Mine Gases Dangerous coal mine gases may be placed in two groups: (I) those that are dangerous because of their explosive properties, and (2) those that are dangerous because of their toxic properties. Methane (CH4) is the important gas of the first group, and in so-called gaseous mines constantly exudes from the coal and rock; it may accumulate and form an explosive mixture. The explosive range of methane-air mixtures is well defined. The low limit is 5 per cent., the high limit 15 per cent., and the most explosive

Jan 1, 1927

By Donald Towse

Portland cement is a basic building material in every country in the world, and, fortunately, the raw materials required in its manufacture are widely distributed. It is a low-priced bulk commodity (price one cent a pound or less, with a density of 100 pounds per cubic foot.) Table 1. Approximate price per pound of selected mineral products. Copper 48 cents per pound Aluminum 27 Lead and zinc 15 Asbestos 3 to 18 Pumice 6 Sulfur 2 Bauxite (abrasive) 1.8 Barite 1 to 1.6 Cement 1 Primitive regions may get along without any Portland cement, but most countries use some, and it is one of the most widespread building materials, even if used in small quantities. Use of cement begins early in a country's development, and, because of local availability of raw materials, cement manufacture is one of the first heavy industries many countries desire. Use and manufacture of cement usually precedes other industrial materials such as steel and heavy chemicals, and consumption levels off for a long period during development of infrastructure and an economic base. With a mature economy comes a very high consumption. Per capita consumption varies ten times or more between nations (Figure 1).

Jan 1, 1970

By Robert D. Brown, Charles A. Sorrell

The decade of the 1980's saw "advanced materials" become a key factor among the industrialized nations, with the United States, Japan, and the European Economic Community being the major competitors. All three have identified communications technology, advanced materials, and biotechnology as the keys to future industrial leadership and the closing decade of the 20th Century is expected to be an era of rapid development and restructuring. The progress of EC'92, the effort to develop uniform standards and remove trade barriers in Europe; the determination of Japan to commercialize advanced structural ceramics, alloys, composites, and superconductors; and the emergence of less developed countries as major supplies of commodity materials pose enormous challenges to the position of the United States as an industrial and financial leader. A consensus is developing that the industries that are first to commercialize the large array of new structural materials and electronic, optical, and magnetic materials and devices will be those who determine the structure of national and world economics. Many technical, economic, legal, political, social, and cultural factors are important determinants in the race to commercialize new materials. Millions of words have been written about these factors and their interdependence; yet the sheer complexity of the problems, the rate at which changes are taking place, and the economic risks involved are so great that government policy makers and industrial decision makers find adequate understanding to be very difficult. Of the many factors involved in advanced materials, the Bureau of Mines has the statutory responsibility to provide information on where materials can be found and how they are mined, extracted, purified, combined, and recycled. It is obvious that minerals availability is essential to implementation of any new technology just as there can be no commodity metals industry if the ores are not available. Because "minerals availability" for commercialization of advanced materials and devices is more complex than for commodity materials and a new mix of materials and processes is emerging, the Information and Analysis Directorate of the Bureau of Mines is redirecting resources to provide reliable information for policy and decision making. The Office of Advanced Materials Coordination (OAMC) was established as a staff operation in July 1987 to assist the efforts of the divisions and branches. The key issues and problems were defined and the role of the Bureau was outlined (Sorrell, 1987, 1988). In February 1990, the functions of OAMC were transferred to the new Branch of Advanced Materials, a line organization parallel with the Branches of Ferrous, Nonferrous, and Industrial Minerals, and was given the responsibility for developing new methods to acquire, analyze, and disseminate information about new materials. The purpose of this paper is to provide definitions, a summary of major issues and problems, an overview of minerals and processing availability problems, and a perspective of the ways in which the mining and materials industries can help to ensure domestic availability of raw and processed materials.

Jan 1, 1990

By Christopher J. Bise

PRINCIPLES OF MINE PLANNING During the initial planning stages, all mining operations are analyzed and evaluated in a similar fashion. This similarity holds true because the mine-planning procedure can be reduced to a network of interrelated systems that are tied together by a common philosophy of mine planning: namely, that the resource is to be extracted in a manner which is safe, efficient, and profitable. The success of the mining operation cannot be guaranteed unless each of these three requirements is met. Fig. 1 shows a flowchart for the initial planning of any mining operation. Notice that there is a preplanning stage that leads to the planning of four interrelated systems. The preplanning stage includes property exploration, estimation of production and manpower requirements, and the establishment of construction timetables. The four systems, evaluated after the pre-planning stage, are broken down into the following: (1) Excavation and handling system, (2) Strata control system, (3) Operating support system, and (4) Service support system. The Excavation and handling system includes the selection of all the equipment for the removal of the resource from its in-place deposit (e.g., draglines, continuous miners, rock drills, etc.) and for the transportation of the mined material from the face (e.g., belt conveyors, trucks, etc.). The Strata control system incorporates all those considerations which maintain the integrity of the roof, ribs, floor, and overburden both during and after the extraction phase; typical considerations in this area include pillar sizing, artificial support of the immediate roof in mine entries, and subsidence protection. The Operating support system contains the "necessary evils" of mine planning; the system consumes a large percentage of the mining engineer's planning time but does not contribute to the actual extraction of the resource. However, if proper attention is not paid to the various components of the system, such as ventilation, drainage, and power, then the mining operation will not perform to its capabilities. Finally, the Service support system is composed of those operations which keep the mine running efficiently; typical examples of these include maintenance and sup- ply. One important concept that Fig. 1 is designed to emphasize is that the four systems are interrelated; typically, a slight alteration of one can affect the performance of another. If these interrelationships are ignored, the effects on the system can be disastrous. The mine preplanning stage and the four subsequent system evaluations constitute the Analysis portion of the mine planning flowchart. After this portion of the study is completed, the overall projected operation can be evaluated by techniques such as financial analysis. This last step in the study is referred to as the Synthesis of the previously calculated parameters into an overall plan. Much has been written about the overall evaluation of mining properties, but, over the past thirty years, very little has been written about the analysis of mine- planning systems in a coordinated manner. Further, those texts which attempted this topic have failed to give sufficient examples for successful implementation, thus supporting the operating engineers' lament that it is easy to discuss theories but difficult to show applications. This text is intended to bridge this gap. Examples of the various stages of the analysis portion of the mine planning flowchart shown in Fig. 1 will be covered in this text, with the exception of the Service support system, since this system is oriented more toward day-to-day planning than long-term mine planning. INTERNATIONAL STANDARDIZATION The benefits that can be derived from an international standardization of the units used in mining engineering calculations are numerous. The interchange- ability of equipment parts and the ability to analyze and compare performance and design specifications on an equal basis are just two of the goals desired by both manufacturers and mine operators. Unfortunately, conversion to an international standard has not been rapidly achieved by engineers in the United States, due to their training under the English system. The Society of Mining Engineers of AIME has made the commitment for the adoption of the Systeme International d'Unites (SI) in all mining engineering calculations. Since many practicing mining engineers and students in undergraduate programs still find difficulty in relating to SI units, the calculations in this textbook will use the English system, with Table 1 available for conversion into SI units.

Jan 1, 1986

By HENRY JULLUM

THE ARGONAUT' mill stands at the crest and spreads down the western slope' of a hill, which incidentally covers the' outcrop of the Argonaut vein' at this point. The collar of the main shaft of the mine is situated on the eastern slope of the same hill 120 ft. below the highest ?point. The present mill, built in 1916, was designed to treat 250 tons per 24-hr. day. This capacity has not been attained recently owing to the inability of the mine to produce enough ore while extensive development and underground construction were under way. At present, however, the mine is more than able to take care of the mill requirements.

Jan 1, 1932

By K. Santowski, S. B. Breyner, T. Prietl

"The material properties of alumina products can be significantly improved by adding Cr203 containing raw materials. Cr203 and Alz03 form an alumina-chromia solid solution during firing, reducing the solution potential when in contact with acidic slags. During service, both a high chemical and high thermomechanical load are present for example in the tuyere zones and taphole areas of metallurgical vessels. For such applications conventional alumina-chromia products suffer from discontinuous spalling as a result of high and frequent thermal shock. Therefore, alumina-chromia materials were developed that exhibit improved thermal shock resistance, compared to the standard products, combined with sufficient corrosion resistance. Laboratory tests evaluated the physical properties of the newly developed alumina-chromia grades and a field test in a Peirce-Smith copper converter demonstrated that the material properties meet the corrosion and thermal shock resistance required for this application. IntroductionTo develop refractory products tailored to specific service conditions it is important to have a profound knowledge of the metallurgical processes and furnace conditions [l]. This enables the specific refractory consumption to be minimized and increases the overall operational efficiency. Economic considerations such as steadily increasing energy and resource costs have resulted in companies investing in recycling processes. In the base metal industry for example, recycling operations involve modifications to the smelter feed, process conditions and chemical composition of the process slags. This adversely affects the performance of standard linings and drives refractory producers to search for material innovations."

Jan 1, 2013

By A. P. Wickland

The characteristic problems related to drilling a hole for evaluation of an orebody are generally quite similar, whether we're drilling a core hole, or a hole to obtain chip samples. The basic objective in each case is fundamentally an economic factor; to produce the maximum amount of usable information per hole at a reasonable footage price. The success of the drilled hole depends largely upon the amount of investigation and research spent on the prospective area and the ability to forecast the capable personnel needed plus the right kind of drills, ancillary equipment such as bits, muds and various additives necessary to make the drilling program successful. The driller is confronted with a wide variation of drilling problems due to the nature of subsurface conditions. Some of these problems are: overburden, which may consist of clays; sand; boulders; or glacial till. These surface conditions may exist up to 2,000 feet in depth and upon reaching bedrock, formations may consist of swelling shales, broken sandstones, and every conceivable rock-type, coupled with every known structural problem such as dips, faults, folds, etc., and to this added extras such as permafrost and/or ground water problems combine to increase the necessity why an understanding of the problems along with the proper reaction of the driller plus the formula to compensate for ground conditions is necessary to complete a drill hole. Since most geologists are familiar with diamond core drilling techniques, I would like to discuss other methods used in evaluating ore deposits.

Jan 1, 1973