Search Documents

By Robert J. Evans

Capital and operating costs were estimated using a wet suppression, fabric filter, and a combination system of the two for hypothetical hard rock stone crushing plants located in central Pennsylvania, operating at 300, 600, and 1,000 tons per hour. Fixed capital expenditure for the dust abatement systems ranged from $49,129 to $249,162. Annual operating costs for the dust abatement systems ranged from $8,394 to $46,606 (0.9 to 3.2 cents per ton). If these dust abatement systems are properly sized, installed, and maintained, efficiencies approaching 95 percent can be expected for reduction in weight of dust particles emitted before control.

Jan 1, 1975

By Jesús L. Valenzuela, José R. Parga, Salvador Aguayo, Héctor Moreno

The Merrill Crowe zinc-precipitation process has been applied worldwide on a large number of operations for the recovery of gold and silver resulting in a higher consumption of zinc dust from cyanide solutions. However, in some of plants this precipitate is of low quality, because lead, cadmium and especially copper are precipitated along with gold and silver. The low quality precipitate also requires more fluxes in smelting and shortens crucible life. In this study, a process is introduced to remove copper, silver, lead and cadmium from barren solutions following the Merrill-Crowe process. Copper and silver are removed by precipitation in a serpentine reactor, using sodium sulfide as the precipitator, and sulfuric acid for pH control. The recovery of lead and cadmium ions with natural hydroxyapatite using cow bone powder (CBP) as a new adsorbent material, is introduced. CBP is capable of removing lead and cadmium ions from aqueous cyanide solutions with 99% efficiency. It has the ability to compete with other existing commercial adsorbents for the removal of lead and cadmium. Results show that pH value has a significant effect on copper cyanide removal efficiency, and it was determined the optimal pH range to be 2 - 3. At this pH value, the copper cyanide removal efficiency achieved was up to 99 %; and for the cyanide associated with copper cyanide complexes, the recovery was 90%. Finally, the precipitate quality was improved 400% .This procedure was successfully run at three mines in México.

Jan 1, 2014

By Bill Cain, R. John Caulfield, D. Scott Kieffer

The East Bay Municipal Utility District is undertaking seismic upgrades of the Claremont Tunnel in the San Francisco Bay area. The tunnel carries treated water across the active Hayward Fault to supply a major metropolitan area. Studies indicate the tunnel could be severed by fault offset during a major seismic event. A design approach to achieve limited operation of the tunnel following fault displacement has been established and design details are currently being evaluated. This paper describes the project, the design approach, and summarizes significant construction constraints.

Jan 1, 2001

By J. R. Kadambi, E. Kucukal, J. Furlan

"Hydrocyclone separators are used in various industrial applications, including mining milling and tailings systems, in order to separate or classify solid particles and liquid droplets from multiphase systems. The flow within a hydrocyclone commonly used in the mineral processing industry was investigated numerically and experimentally using Particle Image Velocimetry (PIV) and refractive index matching techniques. The computational simulations were performed using a commercially available CFD package, STAR CCM+. Two turbulence models were used in the numerical calculations: the k-? model and the Reynolds Stress Model (RSM). In both cases, the first order discretization scheme was unable to resolve the flow characteristics accurately due to the high levels of numerical dissipation. PIV measurements were taken at various spatial locations along the cyclone. Both the numerical simulations and PIV data demonstrate that tangential velocities tend to increase when going radially inward from the cyclone wall towards the vortex finder, and reach a maximum value before they begin to decline rapidly and eventually become zero at the wall. The results also demonstrate the utility of non-axisymmetric approaches in cyclone flow simulations for a greater understanding of the fluid mechanics. The computational results were validated globally using pressure and flow rate readings at the boundaries and locally by comparison to the PIV velocity vector maps and profiles. The comparisons demonstrated good agreement between the two models.IntroductionHydrocyclones are devices used to separate and classify solid particles or liquid droplets from liquid-solid or liquid-liquid systems. Versatile in application, they have been widely used in many industrial applications including the food, oil, power generation, chemical and mineral processing industries since 1891, when the first hydrocyclone was introduced by Bretney (Park, 2003). Hydrocyclones have a relatively simple design with no moving parts, which leads to an efficient separation process."

Jan 1, 2016

By M. Holm

Coal is an important fuel for energy generation, and since there are no adequate alternatives it will also be for the next decades. The deep lying hard coal is important in particular because of its high energy content. Automation of underground mining has led to major improvements in productivity and safety. A fully mechanized longwall shearer workface has already reached a high degree of automation and provides a high productivity for example utilizing the memory cut. Current researches and developments in longwall mining are focused on extending this method by adaptive cutting drum height adjustment. The so-called horizon control is often based on memory cut methods. Horizon control in this way requires information of the environment, which can be provided by models (seam model, cut model) and coal interface detection (CID). Available CID systems only provide an optimal output under specific conditions. The authors propose the shield-data-based horizon control (SDHC) system as an alternative approach. SDHC does not require information from a CID system or an environmental model. All necessary information is provided by roof supports, shearer and process monitoring. The SDHC system was tested in simulation under different seam conditions and yielded promising results which will be presented in this paper. In cooperation with the German mining company RAG the SDHC has already reached an experimental stage. A test assembly was built up at the surface and the SDHC system was implemented on real mining equipment. To make the test scenario as realistic as possible, the SDHC system was only connected to the monitoring system, not to the simulation model. The aim of these tests was to establish the cooperation between all subsystems, find appropriate controller parameters, locate and address safety critical aspects and finally to achieve an automatic cutting drum height adjustment. An introduction of SDHC for shearer guidance is given in this paper. The experimental tests are described and the control results of the realized SDHC system on the test assembly are shown.

Aug 1, 2013

By Chester M. F. Peters

The opportunity to make a close study of the available geologic data existing along the line of the California Aqueduct crossing of the Garlock fault in the Tehachapi Mountains was brought about first by my involvement in the prebid examinations, and later with contractors' claim cases. The California Aqueduct crosses through the western end of the Tehachapi Mountains and cuts across the Garlock fault zone at a location about 9 miles east from its junction with the San Andreas fault zone. This is about 65 miles northwest of Los Angeles and 38 miles southeast of Bakersfield (Fig. 1) (1). This map was published after the tunnels were started and shows the corrected geology. At the crossing the fault has north and south branches which extend northeastward for about 22 miles before converging. In the vicinity immediately east of the tunnel line the north branch of the fault starts to converge toward the west. After crossing the line it passes under the upper plate of the apparent easterly extension of the Pastoria thrust fault, so the actual junction with the south branch is obscured. The aqueduct design called for the expected active slip zone of the north Garlock fault branch to be crossed by the 2,800 foot long Pastoria siphon, which connects with the north portal of Tehachapi Tunnel No. 3. The tunnel would extend through the western end of Genghus Ridge which lies between the north branch and the main south Garlock fault zone in Beartrap Canyon. Here again the

Jan 1, 1997

By G. W. Toth

The coal mining cost models described in this paper represent a computerized estimating procedure for analyzing mining costs and requirements of proposed coal mining projects. Both surface and underground mining analyses can be conducted through the use of these models. These models were developed by the NUS Corporation for the Electric Power Research Institute (EPRI). The methodology design of the cost models follows a process engineering approach for determining mining requirements and costs similar to the logic typically employed in preliminary mine feasibility studies. All capital and operating costs associated with a new coal mining project are thereby estimated. The results of these analyses are then entered into a financial analysis framework which computes annual cash flow summaries, utilizing a profit and loss statement approach, to solve for either the coal value/ton (minimum required selling price) or the rate of return on equity for the project. The coal value/ton is also referred to as the economic cost of production (F .O . B. mine, including preparation).

Jan 1, 1980

By Kadri Dagdelen, Lee J. Zamalloa

Modern surface mining operations are always seeking for minimizing costs while increasing production rates, among the optimization of other specific tasks that have an impact on the economics of the mine. Specifically, the cost related to the production fleet operation (shovels and trucks), the maximization of the overall performance of the equipment, and the uncertainty to meet the goals at the end of the operational time horizon are always topics of discussion with no apparent simple answer. On the other hand, truck-shovel dispatch systems based on Linear/Non-Linear Programming Algorithms have been in operation since mid-1990’s with different levels of success depending on the correct arrangement of operational resources and the complexity of the mine, but having in most cases some important shortcomings related to the way these systems deal with the decision making of the operational objectives, being necessary to have a human agent (dispatcher) to guide the system when the operational parameters change, creating the possibility of suboptimal decisions due to the human factor. This paper discusses the implementation of a novel methodology based on AI techniques to assist in the decision making of the best goal selection when operating a Fleet Management System, taking into consideration time periods as variables and integrating them as part of the analysis, providing a better overview of the forecast plan completion with respect to previous production numbers and evaluating best alternative to handle future events to minimize losses or maximize profits, resulting in better truck assignments, minimum shovel idle times and overall productivity improvements of the operation at the end of the time horizon.

Jun 25, 2023

By M. R. Tavakoli Mohammadi

Novel solvent extraction technologies in recent decades have made attempts to show the problems in applying this method for dilute solutions and find appropriate solutions to overcome them. Improving the equipments performance used in this method for dilute solutions, cause development of usable resources and reduction of operational costs. Furthermore, appropriate conditions provide for using dilute solutions produced in various industries as a new source of valuable elements. Thus, this proposal can be a very good solution for treatment of these solutions and reduce the environmental impacts associated with them. The purpose of this study is to introduce a new method of Column Floto Extraction (CFE), which has been invented in this regard. In this method, using spargers similar to Jameson cell downcomer in floatation process, the organic phase bubble dispersion has been used instead of its drop dispersion in aqueous phase for the two-phase mixture operation. This operation mode has caused a higher extraction percentage of solute in high aqueous to organic ratios due to enhancement of contact area. In this study, in addition to explaining the advantages and features of this method, we have dealt with its design and performance mode.

Sep 1, 2012

By Leonardo Massone

The p-y method is one of the most popular methods in pile design and has been calibrated for various boundary conditions using numerical and experimental studies during recent years. Most studies on reinforced concrete (RC) piles have included the impact of flexural nonlinearity, (e.g. nonlinear moment?curvature relations) but not considered associated pile shear deformations when deriving p-y curves from field data. Common p-y curves may be better applicable for piles with flexure dominated failures (e.g. piles with free- head boundary conditions). For piles with fixed head boundaries (i.e. rotation restrained piles) shear deformations could be of significant influence. To study this problem, a coupled shear flexure interaction model for axial-bending-shear behavior coded in OpenSees was applied to a 0.61 m (2 ft) diameter flagpole and a 0.61m (2 ft) diameter fixed head pile specimen to investigate the possible influence of shear deformations to the overall pile responses. The surrounding soil was represented by p-y curves derived from prior large scale testing on piles with similar boundary conditions. Analysis results show that for flagpole piles, shear forces and shear deformations were insignificant. Considerable contributions of pile shear displacements and forces were observed for the fixed head pile, with shear displacements contributing up to 40% of the total pile displacement. Results suggest that nonlinear shear deformations for reinforced concrete piles should be considered for fixed-head or similar conditions, and that currently used p-y curves may underestimate the actual lateral pile displacement and possibly lead to unsafe design for the particular boundary condition.

Jan 1, 2012

By Rob Thomas

Adequate load transfer is considered essential for optimum ground support and is increasingly important in weak roof and/or high stress environments. If adequate load transfer is achieved not only can this have a positive impact on the resulting roof behavior, but it may also allow the use of lower and hence more economic densities of roof support. A wide variety of post-groutable cable bolts are currently in use in the Australian coal mining industry, each of varying capacity, design, and grouting methodology. Though all of the cables are supplied with the appropriate steel specification, strength, and modulus data, the Australian coal mining industry does not have access to a comprehensive and comparative database on the corresponding load transfer performance, which is a critical problem. On the basis of the above, this paper describes the methodology and results of a laboratory pull testing program that aims to assess the impact of cable bolt design on load transfer, and specifically, the impact on the capacity and stiffness of the anchorage. As part of the testing program, 19 cables were tested including (1) plain-strand cables installed in holes drilled with 28 to 55 mm diameter drill bits and (2) bulbed and nutcaged cables installed in holes drilled with 42 to 64 mm diameter drill bits. Other parameters assessed included the significance of smooth and profiled wire, wire packing, and expanded geometry bulbs. The main results of the testing indicate that in comparison to plain-strand cables, if the cable is bulbed or nutcaged, the capacity of the anchor can increase by up to 400%, and the peak stiffness by between one and two orders of magnitude. The results also indicate that increasing hole diameter may have a positive impact on load transfer in the case of bulbed or nutcaged cables and a negative impact on plain-strand cables. No conclusive results were obtained with regard to the impact of grout strength on load transfer.

Jan 1, 2012

By H. R. Shell

Of three known compounds in the ternary system K20 - PbO - SiO2, one having the composition K2Pb4Si8021 crystallizes into a structure with asbestiform properties. This compound, whose silicon-oxygen ratio is between that of the layer silicates (for example, mica) and the double-chain amphiboles, crystallizes in the tetragonal system. It malts, apparently congruently, at 779° C. The fiberized product prepared from crystals is fluffy and closely resembles natural asbestos in appearance, but is more brittle and has less strength. However, potassium-lead silicate may be separated into fibers with a uniform diameter of 200-300 A.U., and the fibers show with the electron microscope the s criteria that have been interpreted as indicating a hollow tube structure in chrysotile asbestos. Since very few inorganic crystalline compounds have such a structure, the material has unusual scientific interest. Microcrystalline potassium-lead silicate was rapidly and completely formed when powdered glass of the same composition was heated to 650° - 700° C, but macrocrystals grew only slowly from the viscous massive glass. Maximum growth rate was 0.12mm. per hour at 700° C.

Jan 1, 1957

By Suresh P. Babu, Joseph W. Leonard, Richard Muter, D. P. Sen

OUTLOOK FOR COAL UTILIZATION In 1975, about 650 million tons of bituminous coal and lignite mined in the United States was used to meet 55% of the primary energy input for electric power generation and 26% of the total industrial consumption.1 Even though this amounts to only 21% of the total energy requirements, it is believed that with the declining natural gas resources and uncertainty of liquid fuel imports, coal will assume a more dominant role in suppplying our future energy needs. A regional breakdown of the coal reserves of the United States along with their characteristics is shown in Table I. At present the United Stares Energy Research and Development Administration (ERDA) and the US Bureau of Mines (USBM) are financing extensive research programs in advanced mining methods and energy conversion processes. The increased demand for wal which may result from these research programs may also create large-scale environmental protection problems. As more and more coal is mined the production of undesirable coal fines and dust also increases proportionally. The USBM and the Environmental Protection Agency (EPA) research in this field includes development in the areas of instrumentation for qualitative and quantitative analysis of wal dust, protective devices, and dust collectors. Dust control by water sprays, steam, and foam are also being investigated. Other aspects of safety in mining include developing methane drainage techniques prior to coal mining, fire and explosion prevention, and neutralization and disposal of acid mine waters. It is the belief of coal technologists that when the emphasis shifts to coal as the primary source of energy. the existing methods of mining and preparation of coal must be improved considerably to supply large quantities of quality coal for energy conversion. It is the objective of the present large-scale research financed by ERDA to produce substitute fuels from coal. Large-scale gasification pilot plants are being constructed by Bituminous Coal Research, Consolidation Coal Co., Institute of Gas Technology, and the Pittsburgh Energy Research Center to produce coal gas of natural gas standards at 1,000 psig. The processes being adopted by these pilot plants are oriented towards recovering most of the sulfur from coal by absorbing H2S and its subsequent conversion to elemental sulfur. The environmental protection standards will be strictly followed in using the results of these pilot plants to construct large-scale coal gasification plants in the latter part of the 1970's. With the increasing awareness of the need for air pollution control, considerable research is being done to minimize sulfur dioxide emission from thermal power plants. Utilization of limestone and dolomite scrubbing systems and caustic treatment of stack gases have proved to reduce sulfur and nitric oxide emissions by about 90 to 96%.3 Currently, about 22 scrubbers are in use in the United States to reduce sulfur in stack gas emission. In the long-term, it appears that optimal combinations will be developed involving both advanced coal preparation technology and wet scrubbing. The sulfur compounds are converted either to elemental sulfur of sulfuric acid. Besides the sulfur compounds, the major byproduct of the coal utilization industry is the large amount of coal ash. The Coal Research Bureau at West Virginia University has developed a practical use for coal ash as a structural material. The coal industry will undergo revolutionary changes when coal becomes the primary source of energy. New coal mining and preparation processes will be introduced to meet the ever-increasing per capita energy requirements. 2. BENEFICATION Introduction Coal preparation, like the beneficiation of ores, is also aimed at the separation of values from associated waste. Even though the unit operations involved when enriching ores and coal are similar, there are certain characteristics unique to coal preparation. Unlike the scattered and concentrated veins of underground minera1 ores, coal is distributed uniformly and very much in abundance in the coal mines. Coal occurs as the metamorphosed sedimentary deposits of vegetable matter, while metal and mineral deposits occur in great varieties of forms, structures, and origin-from igneous to sedimentary and metamorphic. The mined coal, being much more friable than mineral ores, is subjected to less intensive size reduction operations. Ores are usually ground to a very fine size for subsequent concentration, while coal is crushed to a coarser size, since considerably less liberation is needed to achieve the desired degree of separation. Since mineral matter is to a great extent discretely distributed in coal, concentration is mainly achieved by taking advantage of differences in specific gravity between clean coal and associated waste. In general, about 90% of coal is concentrated using specific gravity separation and about 10% by froth flotation. In contrast, these operations are frequently reversed in the beneficiation of ores. In coal preparation almost all fractions separated during various stages are made use of. while large amounts of gangue material are rejected in the concentration of ores. Hence, coal generally has a much lower ratio of concentration than ores. Since ore deposits are frequently more variable and mineralogically complex than coal, beneficiation of ore may require more plant flexibility and point-to-point quality control. This characteristic difference between the mineral ores and coal is attributed to the generally used one-step processing in coal as compared to the multiple-step processing of ores. Dewatering to enhance the energy content of coal is usually considered a major unit operation. Even though thickening and filtration are common for dewatering ore concentrates and cleaned coal, vibrating centrifuges and disk filters find unique application in the coal industry for achieving these types of solid-fluid separation. In coal preparation, thermal drying is carried out in separate units at the mine. While ore concentrates are usually dried at the smelter. Although the drying of ores is seldom considered dangerous, volatile matter and combustible dust are reasons why the thermal drying of coal can be hazardous. Open air storage of ores and mined coal results in partial oxidation. Unlike the oxidation of ores, the oxidation of the pyritic and carbonaceous constituents of coal together with the heat of condensation of moisture contribute to spontaneous heating and the subsequent combustion of coal in storage. Among the other significant difference between concentration of ores and coal are the weight and capacity of processing equipment. Coal processing employs less cumbersome, higher capacity units while the beneficiation of ores usually requires much more massive and frequently lower capacity equipment. Properties of Coal Which Influence Design The widely varying and heterogeneous composition of coal, due to metamorphism, determines the preparation design and uses of the resulting products. Petrography serves as a useful system of classification to identify the coal types present and their distribution. Early

Jan 1, 1985

By Jiann-Yang Hwang

Microwave heating has been proved an effective method to rapidly heat iron oxide. This offers an opportunity to apply microwave heating in the steelmaking process. The reduction reaction of iron oxide is traditionally achieved at high temperature with reducing gases such as H2 and CO generated from various sources, including coke, coal, and natural gas. This study investigates the differences in iron oxide reduction using conventional and microwave heating under H2 and CO atmospheres. A special microwave thermal gravimetric device was designed and built to facilitate the investigation. With this device, iron oxides can be heated by electric resistance heating, microwave heating, or a combination of methods. The incoming CO and/or H2 also can be preheated to simulate a potential utilization of recovered heat. The iron oxide weight and temperature can be monitored during an entire reduction period. A series of reduction experiments have been conducted. The results are presented and discussed.

Jan 1, 2006

By Laszlo Valentyik

The wide scale acceptance of the heavy media separation is due to its simplicity and efficiency. The two most important variables of the process are specific gravity and consistency of the medium. The latter is a function of the settling rate of the media solids. The almost always present clay in the feed and conse¬quently in the medium acts as a stabilizing agent, and its optimum concentration varied between 3-4%.(1,2) Since polymers essentially perform the same function in oil well drilling muds - i.e. to suspend cuttings during drilling - as the fine clay in heavy media separation, this led to the investigation of whether polymers could be used in heavy media separation as supporting agents. During the first phase of the work, it was found that by the controlled addition of polymers, the stability of the heavy media increased without unduly increasing viscosity of the suspensions, thus yielding conditions for more effective and efficient separation. The results of the experiments were reported in a paper at the AIME Centennial Annual Meeting, March 1971.(3) This paper presents the results of the experiment carried out during the second phase of the work.

Jan 1, 1975

By Kevin Lofftus

The rest potentials of molybdenite electrodes are measured as a function of pH in absence and presence of flotation reagents. The chemicals used include sodium ethyl xanthate, kerosene, dextrin,sodium hydrosulfide, hydrated sodium molybdate, sodium sulfate, and hydrated sodium thiosulfate. The effect of dissolved oxygen is also noted. The obtained data are correlated with the results of micro-flotation tests obtained under similar chemical conditions.

Jan 1, 1984

By Mehmet Bugdayci, Onuralp Yücel, Yeliz Demiray Cucurachi, Ahmet Turan

The production of strontium (Sr) metal from its oxide via an aluminothermic process under 1–5 mbar pressure was examined in this study. SrO of 99%purity by weight was used in the experiments. The effects of stoichiometry and the duration of the process on the efficiency ratio of the metallic strontium were examined. The effects of functional additives (BaO, CaO, CaC2) were also examined. Characterization was carried out using X-ray diffraction spectrometry (XRD), atomic absorption spectrometry (AAS) and flame photometry techniques. The highest Sr efficiency ratio obtained was 96.89% in the experiment conducted at 1250 °C with 300% Al stoichiometry and 300% BaO stoichiometry.

Aug 7, 2020

By Marvin L. Whisman

This report describes the preparation of tritium-labeled organic compounds to be used by the Federal Bureau of Mines in studying the role of certain gasoline constituents in gum-forming mechanisms. The gasoline constituents that have been investigated boil within a range of approximately 90 to 230° C. and can be classified as paraffins. naphthenes, olefins, diolefins, monocyclic aromatics, polycyclic aromatics, and organic sulfur, nitrogen,: and oxygen compounds. The technique of Wilzbach has been applied to more than 50 samples. Purification techniques have been developed that accomplish rapid and effective purification as well as removal of labile tritium in a one-step operation. Data are presented to show the rate of exchange between tritium and hydrogen that can be expected for a variety of compounds common to a full-boiling-range gasoline. These values should be useful to other investigators using tracer programs involving tritium labeled compounds.

Jan 1, 1961

By John A. Gann

WITHIN a very few years magnesium has sprung from oblivion, from classification as a technically unknown, little appreciated, and expensive material to front-page importance in many fields of engineering. Bunsen may be considered the real founder of our present magnesium industry. In 1852; he prepared this metal by the electrolysis of fused magnesium chloride in a porcelain crucible. In the following years the electro¬lytic process became recognized as superior to chemical reduction methods and Germany became the world's chief producer, installing the first electrolytic magnesium plant in 1886. ' Thirty years later, national defense requirements, occasioned by the outbreak of the World War and the cutting off of imports, caused France, England, and the United States to begin production. Most of this magnesium was used for military purposes so the close of the war resulted in a large curtailment in production. A few companies, however, encouraged by the early success of the Germans and by the rapid developments taking place in aeronautics, and confident in the certain future and ultimate value of this metal, undertook extensive re¬searches in its production and utilization. A variety of production methods, both chemical and electrochemical, were investigated and some of them operated on a commercial scale. Reduction of the oxide with carbon at high temperatures and the electrolysis of the oxide in a fluoride

Jan 1, 1932

By Carlos M. Fontes Vieira, Ruben J. Sanchez Rodriguez, Carlos E. Gomes Ribeiro

"In this study we attempted to model a response surface for the apparent dry density of ternary blends of calcitic marble particles. The crushed marble was divided into three granulometric ranges. Simplex network methodology was used to determine the mathematical relation between granulometric ranges and apparent dry density (ADD) of particle mixtures. A highly significant regression was obtained and the simplex network methodology proved to be able to predict high packing particle compositions.IntroductionProblems with packing and expected porosity of particles are common and widely recognized to be important in terms of both fundamental physics and engineering applications. For example, densification of a powder mass is important in the shaping of solids in ceramics, powder metallurgy or composite synthesis; chemical processes such as solid-liquid separation (sedimentation, thickening and filtration), raw material handling (stockpiling, blending, drying, storage and transportation) and pyrometallurgical processes (agglomeration, coke making, ore sintering, blast furnace iron making and new iron making processes) [1,2].Many factors can affect particle packing, but in practice, there are three main factors: (dimensionless) particle size distribution, particle shape and absolute particle size [2].Geometrical and practical methods were developed to predict properties in mixtures. Zou, Gan and Yu [2] present a paper treating a prediction of the porosity of multi-component mixtures of cohesive (fine) and non-cohesive (coarse) particles. Bahiense et al. [3,4] used a simplex network to determine a mathematical model for obtain the optimal compositions between aggregates to a greater packing of a ternary particles mixture. Despite these techniques for predicting particle packing, some studies in particulate composites production don't present clear criteria for choice of particle distribution [5,6]. As the best particle packaging depends on the size, distribution and shape of these particles, individual models can be constructed for specific combinations of these factors."

Jan 1, 2014