Search Documents

By R. Frank Chiappetta

A new blasting technique has been developed by International Technologies, LLC. to eliminate subgrade drilling, lower ground vibrations, improve fragmentation and reduce explosive consumption. The new technique utilizes a uniquely designed borehole plug, with a bottom hole air deck and a predetermined stemming mass on top of the plug. This combination is referred to as the Power Deck?. Single holes and full scale tests were conducted by Blasting Analysis International, Inc. (BAI) to determine how the system works, the mechanisms behind its success and the best design parameters to use for the given rock conditions. Results have shown reduced or eliminated subgrade drilling, ground vibration reductions of up to 33%, reduced explosive consumption by 16 to 25%, and improved fragmentation by up to 25%. This paper summarizes the methodology, field test setups, analyzes procedures and results for one series of single hole and full-scale tests which were performed in a Pennsylvania, USA quarry.

Jan 1, 2004

By Lung Cheng

The Bureau of Mines conducted laboratory tests to investigate the ease of frictional ingition with frozen (nonrotating) conical bits cutting into sandstone. The number of strikes with a new bit to obtain ignition of a combustible methane-air environment was measured. Tests were made with bits tipped with both tungsten carbide and steel at several bit attack angles (angle between bit axis and sandstone surface) and initial tip angles (included angle at the tip of the new bit). Carbide-tipped bits required more strikes for ingition than steel-tipped bits, by a factor of 7 to 10. With a carbide-tipped bit, the number of strikes for ingition increased by a factor of about 3 if the bit attack angle increased by 10° or if the initial tip angle decreased by 10°. During use, abrasive wear of the frozen bit caused a flat surface to form at the tip of the bit, thereby decreasing the tip angle. As the attack angle increased, however, the new bit involved a smaller wear-flat area whereby, abrasive wear was decreased.

Jan 1, 1987

By R. A. Burns

The production of kaolin and calcium carbonate in North America exceeds 13 million tons sold into higher value market segments. With a few exceptions, the markets supplied exhibit mature growth rates. In some market sectors, technology changes have and continue to occur shifting pigment-type consumption and growth. New sources of supply will impact current businesses. New product and process developments for kaolin and calcium carbonates are continuing. Each of these issues is examined in developing a view of the future for kaolin and calcium carbonate in North America.

Jan 1, 1997

By J Sarvinis

The design and operational aspects of fluidised solids transfer-cooling devices will be discussed in this presentation. The devices include air slides and fluoseals (also called seal pots, loop seals, etc), which are widely used in metallurgical plants and other processing plants. Cooling can be achieved while solids are transported in the solids transfer devices. The units combining solids transfer and cooling provide compact and clean plant layouts and also reduce capital and operational costs. Fluidised devices provide excellent gas-to-solids and gas/solids-to-surface heat transfer rates, hence high cooling efficiency. Fluidising gas, such as air, nitrogen or other gases, can be used as direct cooling mediums. Coolants such as water, steam and other liquid or gas cooling fluids can be used as indirect cooling mediums via tube coils immersed in the fluidised solids. The fluidised transport devices share some common features with fluidised bed equipment. The air slide is similar to a linear fluidised bed while the fluoseal is similar to a circular fluidised bed. Therefore fluidised bed design techniques are applicable to the design of the air slides and fluoseals. The heat and mass balance and temperature profiles of the devices concerned will be discussed in the presentation. The design criteria and operational philosophies of the critical components such as tuyeres and air spargers will also be discussed.

Jan 1, 2006

By P. F. Gnirk

Consideration is given to creater formation with shallow, contained, chemical explosions in rock masses which exhibit different inherent physical and mechanical properties as determined by standard laboratory techniques. The primary purpose is to determine whether or not a simple but useful generalized correlation can be established between explosive crater formation and one or more common rock properties. Such a correlation could be beneficial in predicting with some degree of reliability the size of a crater which could be expected in a particular rock type for a given input of explosive energy. A series of crater formation experiments employing constant weight charges of Gelex 2 explosive was conducted in five submembers of the taconite formation at the eastern end of the Mesabi Range in northeastern Minnesota. Five mechanical and physical properties-unconfined tensile and compressive strengths, Young's modulus of elasticity, longitudinal wave velocity, and density-were determined by conventional laboratory techniques using core samples from the taconite submembers. Although insufficient data were obtained to warrant the use of mathematical methods in the determination of empirical relationships, the results provided a fairly strong indication that with an increase in magnitude of any one of the five rock properties definite decreases in the optimum crater volume and surface area occur. Furthermore, for a constant explosive energy input, the presence of bedding planes and joint systems in a rock mass influences the formation of craters in such a manner as to increase the volume of rock broken substantially above that expected from the same rock mass without joint systems and, in particular, without bedding planes.

Jan 1, 1968

By Ekhlaq A. Khan

"The new third Bridge over Narmada River at Bharuch which was recently completed is characterized by some aesthetically appealing elevations of the pylon and large size of the deck. This paper gives an insight to design and construction technique adopted for foundation construction of Extra-dosed span - 3 rd Narmada Bridge at Bharuch over river Narmada, Gujarat. Site being located in intertidal zone had its unique geological characteristics and own set of difficulties during construction.INTRODUCTIONThe Indian subcontinent offers diverse subsoil conditions. With current modern and future trend of long span bridges the substructure design often demands large size foundations. The foundation of theses bridges are usually deep and large in size. The execution of such foundations in maritime environments often involves important temporary works, in order to provide a safe workplace, comply with environmental requirements and achieve high quality standards.Often Pile foundations are preferred solution now a days, but due to various statutory and environmental regulations their construction poses a challenge. With better equipment and corresponding quality control, construction of large diameter pile foundation has emerged as a faster and reliable option.OVER VIEW OF THE PROJECTThe first two lane bridge on NH-8 (Vadodra – Mumbai) known as Sardar Bridge was constructed in 1977, subsequently an additional two lane bridge was constructed in 1999-2000, 29 m downstream of the first. In view of rising volume of traffic and as part of upgradation of NH8, National Highways Authority of India (NHAI) proposed to construct 3rd new 4 Lane Bridge 100 m downstream of 2nd Narmada Bridge, based on Central Water and Power research Institute (CWPRS) study and recommendation.The general layout (fig. 1) of the 3rd Narmada bridge has 8 spans of 144 m and 2 spans of 96 m with total length of 1344 m, supported by132 nos. of 1.5 m diameter piles of about 50 m depth. The substructure has leaning “Y” shaped lower pylon of height 30 m together with cast in situ pier diaphragm. The piles are of M40 and superstructure & pylon of M50 grade of concrete."

Jan 1, 2017

By Z. Chen

This study is concerned with the behavior of bubble clusters in a well-controlled turbulent flow. We used a specially designed cell where the bubble aggregates could be formed and exposed to breakage by a rotating impeller. The effects of impeller speed and the concentration of collector on cluster behavior were studied. It was found that the size of the clusters increases with the concentration of collector used. We also found that although the clusters could easily be destroyed under the action of impeller, they could reform, especially at lower impeller speeds. It was observed that the size of the bubbles arriving into the impeller region in the absence of particles before breakage was considerably higher than the size of the clusters formed at the same impeller speed. It appears that both cluster breakage and re-formation take place simultaneously, and the extent of formation and regrowth is mainly determined by the hydrophobicity of the particles and the impeller speed.

Sep 1, 2012

By A L. Welsh, P S. Newling

Mill operators are entrusted to manage what are normally the largest capital assets on any mine site. Achieving maximum utilisation and lowest costs that drive operating margins are realised by applying well known fundamentals of good housekeeping and proactive (as opposed to reactive) maintenance programmes. Historically, maintenance and operations staff are bought in late during the construction stage and often do not have the time, know how or tools to put in place (let alone train the incumbent staff) a functioning maintenance system before commissioning starts. They then get drawn into a reactive maintenance paradigm as teething problems post commissioning are dealt with and day to day issues envelop the line tradesmen and supervisors. Additionally, even when some semblance of a planned maintenance system is established, it is often the case that over time personnel and cultural issues mask the development of problematic maintenance practices. As has been observed by the authors on many occasions, even when some basic programmed maintenance system is in place, the collection of maintenance data is often inaccurate, incomplete and not subject to analysis. The net result is of course a high incidence of machine failure leading to lower than expected availability, which ultimately translates to lower revenue and higher net maintenance costs. The time taken and the cost to repair a failed machine is always greater than the timely and planned repair of a worn machine.Upon review of a number of processing plants around the world, especially gold and small base metal operations, it is apparent that companies need to implement maintenance systems whereby the operators are not overwhelmed with data and can manage by exception. Inadequate or inaccurate data collection and analysis result in poor decisions being made and misguided actions taken. GR Engineering Services (GRES) has developed a system to enable the custodians of mining plant assets to make more effective and effective use of maintenance data by being able to focus on the indicators of plant deterioration and to programme concurrent maintenance activities to maximise plant availability and utilisation.This paper outlines the structures that can be employed to address the challenges of implementing a proactive asset management system. The best practice strategies described herein have been based on the fundamentals of a sound asset management framework:a phased approach to the development of Asset Management methodology and processeseffective implementation of programmed maintenance routinesmanaging asset condition data collected from various sourcesefficient analysis of asset data and management by exceptioninterfacing asset management data with Computerised Maintenance Management System (CMMS) and Electronic Management Systems (EMS) systemstips to assist with maximising asset performance.CITATION:Welsh, A L and Newling, P S, 2015. Operating strategies for custodians of company assets creating wealth, in Proceedings MetPlant 2015, pp 338–352 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By M. E. Tyrrell

Magnesia spinel (MgO.Al203) recovered from dusting slags in the system MgO.Al203-2Ca0.SiO2 is in the form of single crystals most of which will pass 35-mash. This investigation was undertaken by the Bureau of Mines to evaluate the concentrates as a refractory raw material. Three specific types of refractory bricks were studied: (1) dense, (2) lightweight bubble, and (3) insulating. Test specimens ware fabricated 1 by dry pressing, fired to 1,675° C., and tested by procedures common to the industry. The concentrates produced a refractor, having satisfactory density and mechanical strength; however, spinal is sensitive to thermal shock and the possibility of producing a spall-resistant brick using aggregate of such small grain-size must be considered remote. Lightweight refractorias fabricated of spinel bubbles were the most promising of the types tested. They were 30 percent lighter in sight than the dense refractory, their mechanical strength was good, and definite superiority in thermal shock resistance was indicated.

Jan 1, 1962

By L. A. Haas

The U.S. Department of the Interior, Bureau of Mines, is conducting laboratory-scale research to determine the leaching conditions required with sulfuric acid for extracting base metal from a matte with a copper-to-nicke1 ratio of 6 to 1. The matte (61.2 pct Cu, 9.7 pct Ni, 3.3 pct Fe, 21 pct S, and about 5 oz of precious metals per ton) was prepared from Duluth Complex (Minnesota) ore by smelting a bulk sulfide flotation concentrate. The matte was pre leached at atmospheric pressure to selectively extract 20 pct of the nickel, and the undissolved solids were referred to as the matte residue. Autoclave leaching of the matte residue extracted over 95 pct of the nickel, copper, and iron. The remaining leach residue in the autoclave contained over 100 oz of precious metals per ton. The leaching conditions required were matte grind of greater than 98 pct minus 325 mesh, pulp concentration of 50 g/1, total pressure of 100 psig with oxygen at 150° C or 400 psig with air at 180° C, 50 g/1 H2S04, 700 rpm agitator speed, and 6 hours of leaching time. The leaching time was decreased to 2 hours by increasing the agitator speed to 1,300 rpm. Sulfuric acid concentration greater than 50 g/1 did not appreciably enhance the base metal extraction, but with less acid, residues with higher iron concentrations were obtained. Supersaturation of the liquor was prevented at 150° C by using a 1ixiviant that contained 30 g/l Ni and 20 g/1 Cu.

Jan 1, 1979

By M. E. Grimes

Rio Algom Mines Ltd. owns eight uranium mines and mills in the Elliot Lake district of Ontario, seven of which were producing before 1960. At present only one mine is operating meeting current contract requirements. Under present economic conditions, it is not feasible to mine ore of less than 2.0 lbs./ton U308, although there are very large reserves below this grade. We are interested in preconcentration for three possible applications: to extend ore reserves by permitting use of lower grade ore, to reduce costs on processing of present grade ore, and to reduce capital investment in expanding production to meet future production goals.

Jan 1, 1973

By F Saloojee, F K. Crundwell

Refractory ores need to be pretreated prior to cyanide leaching for acceptable gold recovery. Pressure oxidation is one method of rendering the ores more suitable for cyanidation. The focus of this work is optimisation of autoclave configuration for pressure oxidation. An autoclave for the pressure oxidation of a feed containing pyrite and arsenopyrite was modelled, using the population balance framework. The autoclave model takes into account feed particle size, reaction kinetics and retention time. Mass balance calculations were incorporated into Cycad Process« software. This allowed for the investigation of different circuit configurations. The base case model consists of a single autoclave. The feed was then doubled and additional autoclaves were added to provide the same residence time as the base case. Four different configurations for the additional equipment were simulated. These were parallel, series, series with inter-stage thickening and parallel-series circuits. The options are compared in terms of extraction and productivity. The parallel circuit behaves similarly to the base case. The series and series-parallel circuits have higher recoveries and productivities than the base case. The series circuit with inter-stage thickening provides the highest extraction and productivity. This is because the thickening reduces the slurry volume and increases the residence time of the solids in the downstream autoclave.CITATION:Saloojee, F and Crundwell, F K, 2013. Optimisation of circuits for gold pressure oxidation, in Proceedings World Gold 2013 , pp 181-188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By D. Warkentin, M. Tomlinson, A. Nacu

"This study focuses on comparing the “blinding” effectiveness of various organic additives as part of a general review of using organic additives to mitigate preg-robbing and improve gold recovery during cyanide leaching of carbonaceous gold ores. The laboratory results compared the impact of various organic additives on the prevention of gold adsorption using both activated carbon and ore samples containing carbonaceous matter, generally referred to as total carbonaceous matter (TCM). Although several organic reagents were found to have a significant blinding effect on activated carbon, these results did not translate into increased gold leaching efficiencies with actual ore samples.INTRODUCTION Preg-robbing refractory ores, which contain carbonaceous matter, have been problematic in cyanide plants for many years. In industry, preg-robbing by carbonaceous matter may be mitigated using various techniques including flotation, to remove the carbonaceous matter; addition of blinding agents, to passivate the carbon surface and prevent adsorption of gold cyanide complex; roasting, to partially or fully destroy the carbonaceous matter; chemical oxidation (Abotsi & Osseo-Asare, 1986); pressure oxidation; or microbial deactivation (Dunne, Staunton, & Afewu, 2013). Carbon-in-Leach and Resin-in-Leach are also used as process alternatives in which activated carbon or resins are used to compete with the carbonaceous matter for gold cyanide adsorption. For highly preg-robbing ores, thiosulphate leaching may be considered as an alternative to conventional cyanide chemistry (Baláz, et al., 2000). Natural carbonaceous matter is composed mainly of hydrocarbons, organic acids, and graphitic/amorphous elemental carbon. Natural elemental carbon that behaves as activated carbon is considered to be the main reason for preg-robbing, although the true nature of this phenomenon is not fully understood (Tan, Feng, Lukey, & van Deventer, 2005). In general, the hydrocarbon fraction is assumed to have negligible interaction with gold, while organic acids, such as humic acids, may form complexes with gold, inhibiting its extraction in cyanide solutions. Organic reagents have been used for blinding carbonaceous matter in gold ores prior to cyanidation. Abotsi & Osseo-Asare (1987) tested various organic compounds, with two possible effects in mind. First, the organic compounds were expected to adsorb onto the surface of the solids as anionic/cationic species; the resulting electrostatic interactions between the Au(CN)2- anion and the negatively/positively charged surface would inhibit/enhance the gold uptake. Second, the organic reagents were expected to coat the surface of the carbonaceous component in the ore, limiting the available adsorption sites and reducing gold losses. Optimal reagent dosage depends on ore mineralogy, maturity and surface area of the carbo"

Jan 1, 2019

By Enrique I. Acuña

Creighton Mine is part of the mining history of Sudbury with more than 100 years of operation. Currently the deeper levels of the mine are reaching the 8000 ft level without implementation of mechanical refrigeration system as a result of the use of the Natural Heat Exchange Area (NHEA) over the past decades. The NHEA of Creighton Mine is part of an old block caving area divided into 4 blocks of trenches that were used to extract the ore. Currently, it is used year round to condition the outside temperature before the airflow enters the fresh air system of the mine. As the mine is progressing deeper, underground temperatures in the lower levels are starting to approach the limit of Vale?s guidelines for working in heat. This paper presents the study developed to improve the management of the NHEA to obtain cooler temperatures at the intake of the ventilation system and outlines the impact to the mine in terms of the additional level(s) that could be operated underground without the use of mechanical refrigeration. This is another of the efforts currently under development for energy conservation and to reduce the capital and operational costs of Creighton Mine while extending the expected life of the mine.

Oct 1, 2010

By Marc R. Laflèche, Suzanne Paradis, A. Shirley Péloquin, Harold L. Glbson, Robin Potvin, Pierre Verpaelst

"The Archean Blake River Group is best known from a central volcanic complex in Rouyn-Noranda. This volcano-tectonic depression, delimited by the Hunter Creek fault to the north and the Horne Creek fault to the south, is interpreted to be a cauldron approximately 20 km in diameter. Its western and eastern boundaries are the Flavrian Plutonand the D'Alembert shear zone respectively. The complex has an exposed stratigraphic thickness of 10.5 km. Two cycles, composed of andesitic units overlain by bimodal, andesite - rhyolite units, are observed in the area, and are, in turn, overlain by an andesitic unit interpreted to be the lower part of a third cycle.The southern sector of the Blake River Group, south of the central volcanic complex, is considered to be outside the limits of the cauldron, but partly contemporaneous with it. The maximum stratigraphic thickness exposed in this area is 4 .6 km. At least two cycles occur in this sector. The oldest unit, a pre-cauldron andesitic to basaltic unit, occurs only in the southern part of the sector. In the north, two partial andesite - bimodal cycles, interpreted as contemporaneous with the cauldron volcanism, are observed.The eastern sector of the Blake River Group, east of the central volcanic complex, apparently overlies the complex. Two units are observed in this sector: a lower bimodal unit and an uper andesitic unit. The bimodal unit is coupled with the uppermost andesitic unit of the central volcanic complex to form a cycle, and the andesitic unit is considered to be the uppermost unit of the Blake River Group. The total exposed stratigraphic thickness in the sector is 2.5 km.The western sector of the Blake River Group, north and west of the central volcanic complex, is interpreted as the lateral equivalent of the complex. Three andesite - bimodal cycles are exposed in this sector, giving a total stratigraphic thickness of9 .5 km. The two lower cycles correspond directly to the central volcanic complex cycles; this correlation is facilitated by two stratigraphic marker units observed on either side of the Hunter Creek fault: the Fish-roe rhyolite flow, east of the Flavrian pluton, and a spherulitic rhyolite lapilli-tuff, west of the Flavrian pluton.Many of the volcanogenic massive sulphide deposits found in the central volcanic complex are spatially and temporally associated with synvolcanic faults, and felsic domes and feeder dykes that are the sites of felsic volcanism in the bimodal units. However, these features also occur outside the central volcanic complex, and the similarities recognized in this work between the complex and the surrounding area suggest that such deposits need not be restricted to the central volcanic complex. The presence of volcanogenic massive sulphide deposits outside the complex confirms this."

Jan 1, 1990

By G Zhang, I Glacken

Multiple indicator kriging (MIK) has been used in the minerals industry for some decades. As one of the non-linear estimation methodologies, MIK has advantages related to resolving multiple or mixed populations, high variability data and strongly skewed distributions. Applying the MIK methodology requires a lot more effort when compared to other non-linear methodologies, for example localised uniform conditioning. This is due not only to the variogram modelling for multiple indicators, but the validation is also very important because the panel model is fundamental for follow-up work, including the generation of recoverable resources at the local or SMU scale. Apart from this, only a few reported case studies of MIK have documented post-processing of the estimated modelled distribution, representing the probability distribution at point scale at un-sampled locations. The MIK post processing should include the change of support from the point scale to the panel scale, and then the extraction of quantile values from the panel conditional cumulative distribution function (CCDF) for localisation of grades into the SMUs within each panel, based on a ranking estimate marking the SMUs from high to low. In this paper, we present a case study on a gold deposit with the MIK method with full-post processing implemented for recoverable resources. The MIK point estimate was carried out with an indirect lognormal change of support from point to panel scale, and localisation was done with a custom script. The localised uniform conditioning (LUC) method was also applied for comparison purposes. The comparison shows that MIK has advantages compared to LUC when comes to capturing the high-grades, especially when mixed or varying anisotropy is present within the mineralisation.

May 24, 2023

By A. K. Sinha

Modern mine ventilation systems have grown rapidly in recent years both in tern of its complexities as well as its value for human health and safety. Although computer models are now available to help the design and operation of mine ventilation systems, considerable differences often exist between the computer based predictions and practical results. Research conducted to compare computer result with practical measurements made in ventilation circuits simulated in a physical model seems to confirm such differences. It is concluded that although a mine ventilation computer model is a very powerful tool, it can be utilized to its full potential only after more reliable input data are developed.

Jan 1, 1985

By Edward L. McHugh

The study area, which comprises 11,500 acres, includes the 9,610-acre Whitewater Wilderness Study Area, in the California Desert Conservation Area, 15 miles northwest of Palm Springs, CA. The U.S. Bureau of Mines evaluation of mineral resources is based on examination of prospects and mineralized areas during the spring of 1981. The Whitewater study area is mainly underlain by granodiorite to quartz diorite and their gneissic equivalents in an igneous-metamorphic complex. Late Tertiary sedimentary and volcanic rocks locally overlie the crystalline complex in the eastern part of the study area. The study area lies between branches of the San Andreas fault system.

Jan 1, 1986

By H. H. Moss

OXYACETYLENE .cutting has experienced rapid development in the last few years and greater advances and expansion and broader application may be expected in the immediate future. Marked changes in cutting practice may be expected as a result of the advances in metallurgical science that have produced special alloy steels with properties requiring different cutting techniques than for ordinary low-carbon steels. Much current attention is being directed to those problems of modified cutting practices. Cutting has thus ceased to be merely a shaping problem. It is rapidly coming to have a predominantly metallurgical aspect. The problem is no longer how to cut a given shape, but how to cut a given steel. The answer

Jan 1, 1936

By R Stead

So many ceramics look the same, but are they?In the past 20 years, there have been significant changes in the materials available, as well as changes to the supply chain, for ceramics used in wear applications in the hard rock mining industry. The biggest change in supply has been from the Chinese market, with many suppliers promoting their products as æstate of the artÆ. Some of them are state of the art, but are they all? There will be some concluding remarks in this respect.There are still some outstanding new developments coming from the more traditional suppliers and these should not be ignored. However, as an end user, how can one be sure that the product received meets the technical specifications of that material?This paper will address some of the questions on how to differentiate between different materials by giving a technical overview of the current (but not exclusive) range of popular ceramics, plus incorporating how these ceramics are used in process plant products by presenting case studies. The presentation will include technical data coupled with micrographs of various ceramics to illustrate just why they are different.It will also be shown that by careful selection of the wear material, it is possible to gain significant benefit when using superior materials in an ore processing plant. The impact of cost of the products, life, process efficiency, and reduced maintenance costs will be considered using cyclone components as an example.The properties (including the microstructures) of the various ceramics will be compared to the application in order to get some understanding of what is considered good or bad.Misra and Finnie (1982) summarised their paper, æA review of Abrasive Wear of MetalsÆ by saying:à it is difficult to give guidelines for selecting materials for abrasive wear resistance. Each application is a different one, and a design engineer has to take into account various other factors such as impact, fatigue and corrosion which are often coupled with abrasive wear. The same applies to ceramics.CITATION:Stead, R, 2013. Applications of ceramic wear materials in the gold industry, in Proceedings World Gold 2013, pp 325-330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013