Search Documents

By N. Dahata

Earlier research has indicated that an addition of titanium master alloy to aluminum alloys, results in improved fillability, grain refinement and finer pores. B206 alloy differs from other alloys used in automotive industry, with lower titanium level. This paper examines the effect of alloy chemistry (copper and titanium levels) and grain refinement (A1-5`)oTi- 1%B grain refiner) on grain size, microstructure and microporosity in B206 aluminum alloy. In this study, characterization of grain size, microstructure and microporosity was carried out using light optical microscopy (LOM) and scanning electron microscopy (SEM). Results have shown that the addition of 0.05 wt % titanium resulted in grain refinement of B206 alloy. With an increase in titanium to 0.25 wt further grain refinement, much reduced pore size and uniform distribution of pores resulted. These results suggest that B206 with proper addition of titanium has a promise as an alloy for automotive casting.

Jan 1, 2007

By V. Herman, B. Knorr, D. Whalen

"Edge effect is a condition widely observed in High Pressure Grinding Roll (HPGR) operations that gives rise to reduced comminution at the edges of the roll surfaces. This effect is caused by a reduction in the local crushing pressure at the edges of the rolls resulting from the sliding friction between the static cheek plates and HPGR feed material. Practically, this has an impact on equipment sizing, as the edge effect leads to coarser particles reporting to downstream equipment in open-circuit operations and increased circulating load and diminished HPGR circuit capacity in closed-circuit operations.To address this, Metso's HRC™ HPGR incorporates an Arch-frame to maintain a parallel relationship between the rolls and allow for the use of a flanged roll design. We conducted a series of pilot-plant tests with a 750 mm by 400 mm HRC HPGR to compare the performance of the flanged roll design against that of a traditional cheek plate arrangement under similar operating conditions. The edge effect was found to be significantly reduced with the flanged roll design. Based on the pilot-plant results, the implications for circuit design, energy efficiency and overall plant performance in a full-scale application were investigated and discussed.IntroductionGlobal trends such as lower ore grades and rising operating costs are driving the market toward more energy-efficient mineral processing solutions, most notably in comminution circuit design. High pressure grinding rolls (HPGRs) have been recognized as an energy-efficient solution relative to more conventional circuit designs. The basic operating principle of HPGRs, in which a fairly uniform pressure is applied to a bed of material in the compression zone, lends itself to this improved energy efficiency (Morley, 2006). Studies have estimated that savings of 10-15 percent are possible when comparing an HPGR circuit with a traditional SABC circuit (Rosario and Hall, 2008). While HPGRs offer a more energy-efficient solution than tumbling mills, there is still room for improvement in many aspects of the design. Edge effect, in particular, is one such aspect that limits the effectiveness of the machines. Edge effect is the impaired performance at the edge of the rolls due to a reduction in crushing pressure (Morley, 2010; van der Meer, 2010). As described in our prior work (Knorr, Herman and Whalen, 2013), edge effect is caused by the interaction between the ore entering the crusher and the relatively static cheek plates positioned at the edges of the rolls. As the material is drawn into the crushing zone, the sliding friction between the ore and the cheek plates inhibits the ability of material to be effectively drawn into the compression zone at the edges of the rolls. This reduces the crushing force in those edge regions relative to the center of the roll where material is being drawn into the compression zone at a higher rate. In addition, the cheek plates of a traditional HPGR design are held in place by spring-loaded brackets that are adjustable to manage the clearance. This spring-loaded cheek plate design prevents full compression of the material in the edge regions of the roll as there is relief at the outer edges."

Jan 1, 2016

By George A. Savanick

The U.S. Bureau of Mines has patented and transferred to industry an abrasive-enhanced water-jet rock drill. This drill incorporates three novel components: a collimator, jet deflectors for cutting clearance, and an unpressurized swivel, which rotates at 1,000 rpm while passing 20 gpm of an abrasive slurry flowing at 1,000 ft/s. Drilling occurs through the action of a 10,000-psi, 2O-gpm water jet into which is entrained 72 lb/min of abrasives. The pumps, hoses, and fittings are those commonly used in the water-jet-cleaning industry. Only inexpensive, common sandblasting abrasives are used. This drill can cut through hard rocks with moderate-pressure jets; e.g., rocks with a compressive strength of 73,000 psi can be drilled with a 1O,OOO-psi abrasive jet. In addition to drilling holes, the drill can cut deep, narrow kerfs; collar a hole at any angle; drill through rubble; and chamber holes. The development of the abrasive jet drill is a significant advance in the state of the art of hard-rock drilling. The Government of the United States has licensed the abrasive jet drill patent to Weatherford Water Jetting Systems.

Jan 1, 1989

By S. N. Bhatnagar, S. K. Haldar

"Mineral exploration is an expensive speculative venture and calls for optimization of sampling. Exploration is generally planned in grid pattern to be conducted in phased manner. The objective of any such campaign is to assess the quality, quantity and its reliability. The traditional estimation methods are unable to provide a means of calculating the degree of reliability. Application of mathematical models can quantify the precision of estimation and bring forth decision-making criteria at any stage.In this paper three statistical and geostatistical models, viz., Frequency, Probability, and Semi-variogram, have been employed to evaluate sequential exploration data of RampuraAgucha zinc-lead deposit. The optimization in exploration for a specific objective has been highlighted.IntroductionAny exploration campaign demands heavy resource investment starting from the collection of the first sample to the production of the first ton of ore. The best estimation would be if the entire orebody is taken out and sampled. However, this is neither possible, nor desirable. Drilling is the primary tool of geological sampling. It shares the major portion of the investment and, thereby, warrants critical analysis at every stage during the ongoing exploration projects.The exploration program should be conducted as a well planned scheme based on a sequential evaluation approach in a phased way to achieve a specific objective. It would then be possible to evaluate exploration data at the completion of each phase by employing computer-based mathematical techniques to quantify the precision of the estimate for fulfillment of objectives. The subsequent drilling program should be modified accordingly."

Jan 1, 1987

By Judy Che, Steven Ceccio, Gretar Tryggvason

"A detailed understanding of drop deformation and solidification is essential for quantitative predictions of geometry and properties of parts made by ballistic particle manufacturing processes. Axisymmetric results of towers built by the deposition of multiple drops are presented. In these computations, fluid flow, heat transfer, and phase change are fully coupled throughout the drop deformation and solidification process. The solution method is based on a single set of conservation equations written for all phases simultaneously. The phase boundaries are treated as imbedded interfaces by adding the appropriate source terms to the conservation equations. A parameter study demonstrates the effect of Weber number, Peclet number, and drop deposition frequency on the final shape of the structure. Numerical results show that most successful method of building uniform towers is when two conditions are met. First, each drop solidifies at the same time in the deformation cycle. Second, the cooling rate is slow enough to allow for good adhesion between drops. The ability to predict the final shape of deposited drops will greatly reduce the amount of experimentation necessary to select the desired set parameters for any artifact.IntroductionMaterial deposition techniques based on layering small molten metal drops holds the promise to build small, coherent three-dimensional structures. In this process, numerous 20-100 µm diameter drops are deposited onto a substrate with a low impact velocity (on the order of 5 mis). Both the momentum and trajectory of each drop are controlled precisely to build up complex parts. This material layering technique differs from processes such as spray forming and splat quenching which involve high impact velocities (on the order of 100 mis) and high frequency deposition with little control over individual drop placement. This process of layering small drops can produce parts with near net shape accuracy, while spray forming produces slabs of material which must then be worked to make a usable part. The ability to computationally predict final drop shape and cooling rate has the advantage of allowing the user to select parameters to produce parts with desired shape and mechanical properties. However, the development of such predictive methods requires a thorough understanding of both drop deformation and solidification"

Jan 1, 1999

By D Clarke, I Minniakhmetov

The Olympic Dam deposit is truly a world-class IOCG-Ag deposit, the world’s fourth largest deposit of copper and the world’s largest known single uranium deposit. Traditional and non-traditional methods have been used to accurately model the geology and mineralisation of the Olympic Dam deposit. Conditional simulation models have long been used as the most robust method for estimating risk and uncertainty in mine planning decisions at other mines around Australia and the world. There are many challenges associated with simulating the Olympic Dam deposit at a selective mining unit size sufficient for underground mine planning purposes. These include the size of the deposit, resulting in hundreds of millions of grid blocks; the disseminated nature of the zoned sulfide mineralisation. And lastly the direct relationship of the relative abundances of the sulfide mineral species that are crucial to the Olympic Dam smelter performance. Several geostatistical techniques have been utilised in the workflow for the Olympic Dam Conditional Simulation model to address these challenges. The key techniques are: • Projection Pursuit Multivariate Transform to de-correlate the main elements before simulation. • Pluri-Gaussian implicit boundary simulation method to simulate the mineralisation domains. • Spectral simulation method of de-trended and de-correlated attributes with account of local varying variance. The resulting conditional simulation models have been validated against histograms, grade-tonnage curves, cross-plots and assessed for variogram reproduction. This paper presents how the final conditional simulation models compare to benchmarking models created using alternate estimation techniques of ordinary kriging and local uniform conditioning. It also presents a validation process using historical samples to test final estimate accuracy of the simulation models.

May 24, 2023

By Kosuke Hosoda, Shuji Owada, Hiroyuki Tokuichi, Hirobumi Ohta, Chiharu Tokoro, Moto-o Sato, Katsushi Okumura, Hiroto Ogawa, Hideaki Umezawa

The Japanese government enforced the "Small Domestic Appliances (SDAs) Recycling Law" in 2013. The law targets metals such as Ta, Nd, Dy, Co, and W to be recycled. Considerable amounts of these minor rare metals are mounted on printed circuit boards (PCBs) of the SDAs and/or e-scrap (electric and electronic scraps). Although precious metals and copper can be recovered from the e-scrap in non-ferrous metals smelters, most of the minor rare metals report to the slag in these smelters in non-recoverable forms. These metals are often used in particular types of devices, and therefore it is possible to concentrate them by separating such devices before feeding to the smelters. In previous work we developed technology for "Device Separation" to concentrate several minor rare metals, but some problems remained, such as how to remove the PCBs from e-scrap bodies, and how to detach devices from PCBs after their removal from escrap bodies. This paper proposes a two-stage crushing process in which, firstly, PCBs are removed from the e-scrap body with various crushers, and secondly, devices are detached from the PCBs involving the application of elevated temperatures. It was found that in the first stage, crushers with physically flexible rotating media such as chains, which provide high collision probability with the sample and consume relatively low energy, can quite effectively separate the PCBs from the e-scrap bodies non-destructively. In the second stage, heating was found to be remarkably effective in helping to detach mounted devices from PCBs, also non-destructively. This paper will also discuss the detailed mechanism of the heating effect on the detachment of devices from PCBs.

Jan 1, 2014

By Luis Calzado P.

La unidad de producción de Cerro de Pasco, perteneciente a la Compañía minera del Centro del Perú, cuenta con importantes reservas de minerales piríticos argentíferos que son tratados en la planta concentradora de San Expedito. Dicho concentrado es usualmente empleado como funderte en el circuito de cobre de la fundición de La Oroya. Sin embargo, dada la finura del material, su porcentaje se ha visto reducido. En este sentido, el presente trabajo señala una alternativa para recuperar la plata contenida en el concentrado mineral a través de un análisis mineralógico del concentrado pirítico. Posteriormente, se describe el proceso combinado piro-hidrometalúrgico que consiste en la tostación-lixiviación, precipitación con polvo de zinc y la refinación hidrometalúrgica. Finalmente como apoyo a la técnica señalada, se agrega el análisis económico para Centromin.

Aug 26, 1988

A static equilibrium mathematical model of the lead,flotation circuit at The Zinc Corporation Limited is developed to permit the feasibility of applying computer control techniques to be studied. The model is based on the relationship between the cumulative recovery of a mineral species R from n flotation cells or assemblies in a unit given asR = M(1-(1 - p)?)where M is the maximum possible: recovery and p is the probability of flotation for the particular mineral.The verification of this relationship by data from pilot plant cell-to-cell and plant open flow flotation units shows that these systems behave as if the probability p is constant for each cell or assembly of anyone unit. It is also concluded from this study that mineral recovery is independent of the head assay. Two consequences of this probability relationship, are demonstrated.1. The total recovery from an open flow unit is enhanced by increasing the number of flotation assemblies but maintaining a constant flotation time and total air addition.2. The rougher and scavenger capacity required to recover a bulk lead-zinc concentrate is approximately half that used for selective flotation.The static equilibrium model is derived by solving a series, of mass balance equations which incorporate the recovery-probability relationship for each type of flotation unit. It is used to calculate the complete metallurgy of the circuit for any arrangement of cells knowing only the plant feed assays and the probabilities of flotation for the three mineral types, galena, marmatite, and gangue for rougher, scavenger, and cleaner flotation. The high degree of prediction obtained is demonstrated by comparison with plant results.Pulp flowrate is the principal variable affecting the accuracy of the present model. Work is in progress to establish this effect and permit the derivation of a dynamic model. Even so, the static model is valuable in its present form for the analysis and design of circuits, and optimisation studies using computer services have been conducted.

Jan 1, 1964

By N Haque

Base metal ores contain low levels of toxic/hazardous elements such as arsenic, antimony, bismuth, cadmium, lead and mercury. Given the large tonnage of base metal ores mined and processed each year globally, the accumulated mass of minor elements introduced into the biosphere is large and could be expected to have a significant environmental impact. Life cycle analysis (LCA) is a methodology that has been developed to assess the environmental impacts of material supply chains over their entire life cycle. Assessing the toxicity impacts of metallic wastes and incorporating these impacts into LCA methodology is not a simple task given the complexity of the issue. However, research and methodology development is in progress internationally to address this. Despite limitations concerning the lack of a coherent framework for characterising the toxicity impacts of metals, including issues such as bioavailability, a study was carried out to give first estimates of the relative toxicity impacts of various waste streams from metal production processes. The wastes considered were: red mud; sulfide tailings (copper, nickel, lead/zinc); lead/zinc slags; synthetic rutile residue; iron oxide residue; and copper slags and anode slimes. These toxicity estimates can be considered the æworst caseÆ scenario for these wastes, where all the metals present are bioavailable. Combining estimates of the amounts of the various waste streams produced in Australia each year with the toxicity results showed that despite their relatively low human toxicity impact per unit mass compared to some other waste streams, red mud and the various sulphide tailings had the highest annual human toxicity load on the environment, along with copper smelting slag and dust. Data from the pH dependent leaching test reported in the literature were assumed to represent first approximations of metal bioavailability and used to compare the two approaches to estimating the toxicity impacts of red mud.

Jan 1, 2009

By J. Q. Chen

The elastic-plastic behavior and the fracture mechanisms of two 2198 Al-Cu-Li thin sheets are investigated. The first material (2 mm thick) is in a recrystallized state after cold rolling. The second material (6 mm thick) is hot rolled and has a fibrous grain structure. The two materials are studied in both T351 and T851 conditions. Tensile tests are carried out along different sheet directions using flat and notched specimens. Fracture resistance was characterized using Kahn tear specimens and M(T) panels. Macroscopic fracture surface of smooth tensile specimens depends not only on testing material but also on the loading direction. For Kahn tear specimens, fracture is initiated in a small flat triangle whereas slant fracture is observed during crack propagation. Fracture mechanisms were investigated using scanning electron microscopy (SEM) and X-ray 3D tomography.

Jan 1, 2011

By Zohreh Kazemi Motlagh, Virginia T. McLemore

Critical minerals are nonfuel minerals, essential to the U.S. economy and national security, whose supply chain may be disrupted. Mine wastes are potential sources of critical minerals. The goal of this project is to estimate and characterize critical minerals endowment in three mining districts in New Mexico: Black Hawk (Grant County), Hillsboro (Sierra County), and Magdalena (Socorro County), and assess their acid-generating potential. The Black Hawk district is an arsenide five-element vein deposit (Ag, Ni, Co, As, U, Bi, and local minerals like Pb, Cu, Zn, W, and Sn). The Copper Flat mine in Hillsboro district is a copper porphyry deposit. The Kelly mine in Magdalena was first mined at 1878 and are carbonate-hosted Pb-Zn deposits. Mine waste rock piles and tailings are sampled using USGS Beta sampling procedure. Geochemistry results show that Black Hawk district mine wastes samples are elevated in Ag (>200 ppm), Co (290 ppm), Ni (2,130 ppm), and Zn (8,463 ppm). Copper Flat mine tailing is elevated in Bi (111 ppm), Cu (7,453 ppm), and Zn (2,360 ppm). Downhole profile plots in Copper Flat show the positive correlation between Cu, S and Te values. Magdalena samples are elevated in Cu (5,700 ppm), Zn (129,500 ppm), and Pb (58,100 ppm). Determination of acid-generating potential in these areas suggests that Black Hawk district mine wastes are non-acid-forming while high S present in some Copper Flat and Magdalena samples can potentially cause acid mine drainage.

Feb 1, 2025

By L. A. Neumeier

The Bureau of Mines evaluated the properties and anisotropy in properties of rolled Zn-Cu and Zn-0.12 pct Ti-Cu alloys with various copper additions to 1.25 pct. The alloys were rolled cold and at various hot-rolling temperatures to reductions as high as 92 pct after breakdown rolling. The properties are extremely sensitive to various combinations of composition, rolling temperature, and rolling reduction, Zn-Cu alloys can develop good creep resistance, but they are inferior in that respect to Zn-Ti-Cu alloys. For alloys either with or without the titanium addition, cold-rolling results in recrystallization of the matrix and rejection of copper from solution, causing poor hardness, tensile, and creep properties, but high ductility. Peak tensile strengths develop when the alloys are rolled in the range 320° to 400° F, Best creep resistance for Zn-Cu alloys requires higher rolling temperatures when copper content is increased. Creep resistance is best for Zn-Ti-Cu alloys with about 0.75 to 1.0 pct CU rolled near 480° F. Some copper is soluble in the TiZn15 phase, which forms into "stringers" during rolling. The possible contributions to creep behavior of factors such as distribution of second-phase particles, grain size, and preferred orientation are discussed.

Jan 1, 1970

By Matthew Price, Laura Brown, Atulya Verma, Samantha Espley

Burst-prone conditions are a significant hazard in deep hardrock mines, elevating the risk to excavation stability and, more importantly, to worker safety. As mining progresses deeper, induced stress changes may trigger the initiation of rock failure processes which can be detected and recorded as mine seismicity. The implementation of seismic monitoring and routine seismic data analyses enables mine seismicity to be quantified spatially, temporally and on scale. The ability to quantify and characterize mine seismicity offers the opportunity to gauge seismic hazard, identifying high risk zones for mitigation against burst-prone excavation failure. Over the last decade, the Mines Technical Services (MTS) group at Vale Canada Limited’s Garson Mine assessed seismic hazard with the objective of assigning practical mitigating controls to zones identified as having a high rockburst potential. Initially, seismic hazard was computed using the Seismic Excavation Hazard Mapping (SEHM) software developed by the Mining Innovation Rehabilitation and Applied Research Corporation (MIRARCO) at Laurentian University, Canada. More recently, Vale Sudbury Operations partnered with the Australian Centre for Geomechanics and the University of Western Australia’s mXrap consortium. Through the consortium partnership, MTS at Garson Mine implemented the mXrap seismic data analyses platform, including the grid-based seismic hazard assessment tool. Building on 10 years of seismic hazard assessment experience at Vale Garson Mine, this paper summarizes a comprehensive case study, comparing the two tools (SHEM and mXrap) used at Garson Mine to assess, quantify, and represent seismic hazard. Subsequently, results of the Garson Mine comparative seismic hazard study will be discussed, emphasizing the need for an all-inclusive hazard assessment tool, focused on delivering practical mitigating controls that further enhance the overall safety of seismically active underground mines.

Apr 26, 2022

By W. Bakiewicz

The Lower Indus Basin deposits form a substantial unconfined alluvial aquifer of excellent quality. This aquifer contains basically highly saline groundwater, overlain in places by considerable amounts of freshwater whose origin can be traced to the present and historical courses of the River Indus. In the past the main source of groundwater recharge has been direct river seepage and water tables were generally deep. Since the establishment of a perennial irrigation regime however, deep percolation from the increased irrigation supplies has predominated and the water-table has risen to within a few feet of the surface. The river system itself is being progressively developed for irrigation and very shortly a situation will arise where the entire low winter flow will be utilised. Fresh groundwater will then be exploited to supplement the surface supplies, and at the same time a drainage system, mainly based on wells will be used to stabilise the water-table at safe depths. This paper discusses some of the methods used to ensure optimum-economic development of the fresh groundwater and describes the general design philosophy evolved by the authors firms for both irrigation and drainage wells, with respect to both well configuation and operation. Water quality standards are discussed in as much as they affect subsequent use of the groundwater. A few particular aspects are considered, including that of the values of the relevant aquifer constants, the construction of wells and the determination of screen losses. A major problem solved during the Lower Indus Project investigations has been the design of wells to-produce fresh water from layers overlying saline water. This solution is also discussed.

Jan 1, 1967

By Timothy J. Myers

Expansion and the economic growth in the southwestern region of Missouri necessitated the expansion of State Route 249 and the construction of a new interchange to provide service to the Joplin, Missouri area. The project is located above a former lead and zinc mine in Jasper County, Missouri and includes a five bridge interchange connecting State Route 249 and US Route 171. The variable subsurface conditions, both natural and manmade, prompted the design team to use ground improvement via grouting and small diameter micropiles to provide support for several of the bridge foundations on the project. The scope of work included mine shaft closures, 56,000 ft of overburden and rock drilling, 11,139 ft of micropiles, 524 cy of balanced/stabilized high mobility grouts, and over 8,700 cy of low mobility grout. The selection of the grout used was based on the actual subsurface conditions. Low mobility grout (LMG) was used in voided conditions and for closure of the mine shafts encountered during the excavation. High mobility grout (HMG) was used in fractured rock with the goal of improving the mechanical properties of the rock underneath the future bridge footings and controlling grout volumes during micropile installation. The split spacing method was utilized for both LMG and HMG holes. Geology of the project site subsurface consisted of extremely variable bedrock with strong to very strong limestone, chert, breccia, extremely weak shale, and weak to strong sandstone. Previous activities associated with the mining disturbance (such as partial filled vertical mine shafts, shallow and deep mine horizons, modified hydrology including artesian conditions) further complicates the site subsurface conditions. Real time monitoring and recording of all drilling and grouting parameters was conducted to assist in the evaluation of in-situ geological properties of the site in order to modify the ground improvement and micropile program as necessary. This paper will discuss the design and execution of the ground improvement and micropile program. The project is an excellent example of the use of multiple ground improvement and foundation support techniques combined with real time data analysis to provide a foundation support solution for a complex geological environment.

Jan 1, 2009

By William Bent

MORE than twelve years were spent by Wöhler at the instance of the Prussian Government in experimenting upon the resistance of iron and steel to repeated stresses. The results of his experiments are expressed in what is known as Wöhler's law, which is given in the following words in Du Bois's translation of Weyrauch :* "Rupture may be caused not only by a steady load which exceeds the carrying strength, but also by repeated applications of stresses, none of which are equal to the carrying strength. The differences of these stresses are measures of the disturbance of continuity, in so far as by their increase the minimum stress which is still necessary for rupture diminishes." A practical illustration of the meaning of the first portion of this law may be given thus : If 50,000 pounds once applied will just break a bar of iron or steel, a stress very much less than 50,000 pounds will break it if sufficiently often repeated. This is fully confirmed by the experiments of Fairbairn and Spangenberg, us well as by those of Wöhler; and, as is remarked by Weyrauch, it may be considered as a long-known result of common experience. It partially accounts for what Mr. Holley has called the "intrinsically ridiculous factor of safety of six." Another "long-known result of experience "-although this has not, as the writer believes, been investigated by scientific experimenters-is the fact that rupture may be caused by a succession of shocks or impacts, none of which alone would be sufficient to cause it. Wrought iron will crystallize by repeated blows in service and become weaker than cast iron. Iron axles, the piston-rods of steam-hammers, and other pieces of metal subject to continuously repeated shocks invariably break after a certain length of service. They have a " life" which is limited. Iron rods in bridges sometimes crystallize and break, although the rods in most of our iron bridges * Strength and Determination of Dimensions of Structures. By Dr. J. J. Weyrauch. Translated by Du Bois, New York, 1877.

Jan 1, 1880

Reduce the dust exposure of workers in large processing buildings at mineral processing operations, using a total mill ventilation system.

Jan 1, 1994

By Jack R. Woodyard

Bonding angles, promotion energies, and relative atomic sizes can be estimated through the solution of a set of algebraic equations generated from simple atomic models, and quantum mechanical parameters such as bond strength can be estimated from simple, hydrogenic form-wave functions. The precepts of The Engel-Brewer Theory are melded with the "Crystal Approximation Model" to produce atomic-structure models making these predictions, The two-valence-electron case is presented in this report. For the candidate atoms Be, Mg, Ca, Sr, and Ba the calculated promotion energies agreed within a few percent of their experimental values. These atomic parameters determine the possible crystal structure of the candidate atoms when alloyed. This is part of the effort at the U.S. Bureau of Mines to develop methods for alloy design in response to requirements for new high-performance alloys that conserve critical or rare materials.

Jan 1, 2010

By Alfonso Rizo-Patrón Remy

El presente texto señala la importancia de los fosfatos en la cuenca del Pacífico. En ese sentido, se describe las condiciones favorables en la cuenca del Pacífico para el planteamiento del manejo de los recursos naturales a través de la infraestructura concentrada en el área de Bayovar, Piura. Así también se revisan los hidrocarburos, los programas de acción, los recursos de agua potable, las condiciones climáticas, el puerto de aguas profundas, pesquerías y otros recursos minerales.

May 1, 1972