Search Documents

[ ] TUNNELS TO BINS. Originally designed for tunnel work, the strong lightweight liner plates used to construct this 30-ft diameter, 31-ft high, aggregate storage bin have several advantages. Bins and conveyor to tunnels can be quickly erected in any season, for permanent service, or to be salvaged and reused. Armco Steel Corp. (16) ROLLER CHAIN: Engineering Data Book No. 2457 published by Link-Belt Co. is a comprehensive 148-page volume on roller chain and its application. Detailed engineering information covers installation, maintenance and lubrication of chains for drives, conveyors, and sprocket wheels. The book covers selection of drives to meet both standard and special installations. (17) LABORATORIES: The Fisher Scientific Co's. line of 21 basic units of standardized steel laboratory furniture is described in catalog no. 25. The Unitized line was designed to combine the advantages of custom installation with the convenience of selection, delivery and continued flexibility that goes with ready-made units. (18) PUMPS: Two similar, but functionally different types of vertical centrifugal wet-pit pumps; a heavy duty bilge pump for handling solids-free liquids and drainage; and a screenless sewage ejector, constructed to handle sewage and solids carrying liquid; are illustrated in a bulletin from Yeomans Bros. Co.

Jan 1, 1952

By W. D. Monaghan, G. L. Mowrey, C. W. Ganoe

In addition to developing various types of coal-interface detection system, the US Bureau of Miner is actively in involved in developing a coal rib-thickness monitoring system for highwall mining applications. One particular system that shows promise in a ground-pentetrating radar system to detect the coal-air boundaries of coal rifts. Based on preliminary laboratory and field tests results indicate that this method can be applied successfully in highwall mines to maintain constant rib thickness. The coal seam should be relatively clean in the vicinity of the antenna (e.g., have minimal partings or dirt bands) for best results.

By W. D. Monaghan, G. L. Mowrey, C. W. Ganoe

In addition to developing various types of coal-interface detection systems, the US Bureau of Mines is actively involved in developing a coal rib-thickness monitoring system for high wall mining applications. One particular system that shows promise uses a ground-penetrating radar system to detect the coal-air boundaries of coal ribs. Based on preliminary laboratory and field tests, results indicate that this method can be applied successfully in highwall mines to maintain a constant rib thickness. The coal seam should be relatively clean in the vicinity of the antenna (e.g., have minimal partings or dirt bands) for best results.

Jan 1, 1996

By M. E. Holuszko

A research program has been carried out at the Mining Department of the University of British Columbia to study the effect of wettability of coal on its handleability and bulk density. The effect of moisture content on the bulk density of coal was found to be more pronounced for hydrophilic coals than for hydrophopbic ones. Altering wettability of coal surface leads to different effects of moisture on bulk density. The samples were studied at different fine fractions content, and it was shown that there was no effect of increased content of fines on the bulk density for hydrophobic coals, while for hydrophilic coals this effect was very significant. It was shown that the moisture content at which the lowest bulk density was reached coincides with the critical moisture content for studied samples, as determined from handleability tests using Durham Cone method. This critical moisture is the moisture content at which a sudden deterioration of coal handleability occurs. Based on the bulk density and handleability tests, the flow theory of moist coal is proposed.

Jan 1, 2006

Future metal prices play a direct role in both the economic evaluation and short to medium planning of a mine scheduling sequence. It is difficult to predict with accuracy the future price of volatile metal commodities, however, it is possible to fix some future metal price, outside of long term contracts by the selling of futures contracts through a commodities exchange. The futures contract represents a fixed amount of a specified quality of a commodity for future delivery at a predetermined price. Several different types of hedging are possible, one in particular which is best suited for mining companies. There are relative advantages and disadvantages when trading in futures contracts and particular reference is made to gold contracts on the Sydney Futures Exchange.

Jan 1, 1980

By D. G. Klaren

Self-cleaning fluidized bed heat exchangers are conquering the world for reason that they are able to solve any severe fouling problem in indirect heat transfer due to the circulation of cleaning particles through the tubes of vertical shell and tube exchangers. In most cases, these particles consist of chopped metal wire. Moreover, self-cleaning fluidized bed heat exchangers perform with excellent heat transfer at very low liquid velocities, which enables completely new designs of conventional shell and tube configurations. This article explains the principle and application of this self-cleaning heat exchange technology and also pays attention to an actual case of a revamp of the severely fouling exchangers of a conventional multi-effect evaporator into a self-cleaning configuration. Possibilities for the revamp of conventional exchangers suffering from massive and very hard scale deposits are found in a variety of metallurgical processes, such as: The refining of nickel, the production of alumina from bauxite and many others.

Jan 1, 2003

By T. A. Farr, I. A. Gibbs, F. Guevara, S. R. Simms, G. Nojima

This paper describes an installation of a medium-voltage adjustable frequency motor drive (AFD) on a high starting torque regrinding mill. This type of application is typically found in the mineral industry dealing with hard ore. The AFD electrical architecture is introduced from line to load. The type of closed loop encoder feedback motor control algorithm is briefly described. The results of the AFD motor identification auto-tuning are compared against the manufacturer’s supplied data. The motor drive performance results are shown for pre-ramp DC fluxing, high starting torque with overload current, excessive load torque stall condition, and blocked rotor. The instrumentation and arrangement for the two watt-meter method to capture low frequency data are presented. The data shown is from the input power quality meter, the AFD computer tool, the output motor protection relay, an oscilloscope, and load shaft connected strain gauge (rotating telemetry for torque assessment). These types of high starting torque constant torque loads are found in mining and process industry applications employing AC adjustable frequency drives. Using field results should help demystify the use of voltage matching output transformers in AFD applications including constant torque loads

Mar 2, 2022

By Fedotov. K. V., A. Y. Senchenko, V. A. Chanturiya

"The paper describes an efficient process to treat the ore from the largest in Russia copper deposit – Udokan. The recommended process is universally applicable to Udokan ores different in composition and allows reaching high copper recoveries during production of high-grade cathode copper and sulphide concentrate with 45% copper content. There are several promising trends for the process optimization and in the case they are implemented, economics of the whole project could improve significantly. One of the most important optimization options implies reduction of specific energy consumption in the course of comminution operations. Another possible option to optimize the already selected process flowsheet is production of cathode copper from sulphide concentrate directly at a mining and metallurgical plant without sending the latter to other metallurgical works.INTRODUCTIONUdokan copper deposit with resources of more than 20 million tons of copper is the largest in Russia and one of the largest copper deposits in the world. The deposit is located in Kalar District of the Trans-Baikal Territory, 30 km away from Novaya Chara railway station of the Baikal-Amur Mainline.Scientists and engineers from various research institutions have studied Udokan copper ores for years. Along the way, some conceptual process flowsheets have been proposed and each of them has its own pros and cons. The key requirement to the processes being developed was their universal application for processing of all the ore types using a single flowsheet. Due to the hard mining and geological conditions and because of complex material composition of Udokan ores it is of great difficulty to design a process which would provide for maximum economic benefits. That is why the process optimization has been ongoing until now.According to the Russian standards, the main input document for design of a metallurgical plant is referred to as a Process Design Report that covers the following key data sections: analysis of metallurgical testing results, validation of the process, design criteria, process flow diagrams, the mass and metallurgical balances, process description, equipment list and other information necessary for the subsequent design."

Jan 1, 2018

By G. E. Kedzie

The ore-deposits of ail that portion of the San Juan country within the borders of Ouray County are either in the tertiary ernptives or, confined to a relatively narrow zone, in the sedimentary beds just beneath them. The ore-deposits in the igneous formation

Jan 1, 1888

By T. T. Field, M. Gell

MUCH has been learned about plastic deformation behavior in crystals through the use of dislocation and slip band etchants. Slip in nickel and nickel-base alloys has previously been revealed by various etching techniques.l-5 The techniques for nickel-base super-alloys4,5 were successful only in the Udimet 700 composition in specific heat-treated conditions. The objective of this work was to develop a more generally applicable slip-band etching procedure. The nominal compositions of the alloys used in this study are listed in Table I. The low carbon Mar-M2OO alloy referred to in the text is the same as listed in Table I with the exception that the carbon content is less than 100 ppm. Mar-M200 and Udimet 700 were solutionized at 2250" and 2150°F, respectively. The aging treatment for both cast alloys was 32 hr at 1600°F and for wrought Udimet 700 was 4 hr at 1975"F, 24 hr at 1550°F, and 16 hr at 1400°F. The new slip-band etching technique consists of a chemical etch followed by a short electropolish, Table 11. Fig. l(a) shows the best result obtained on an internal section of a plastically deformed single crystal of Mar-M2OO when using a conventional slip-band etching procedure which consists of electropolishing followed by etching. Ghostlike traces corresponding to planar slip bands are observed, but the contrast between the bands and the background is weak. Fig. l(b) shows the same field using the new slip-band etching technique. After the etching step of this technique, the same ghostlike traces of Fig. l(a) are observed, but the subsequent electropolishing accentuates the slip bands and the subgrain boundaries while the rest of the matrix is being polished. Longer electropolishing obliterates the slip bands. The new slip-band etching technique makes use of the etchants and electrolytes that are normally used for a given material. Because of this, it should be possible to slip-band etch other nickel-base superal-loys by using existing etchants and electrolytes for a material and following the procedures outlined in the "Comments" section of Table 11. All the illustrative examples given below show internal plastic deformation in single crystals of regular and low carbon Mar-M200 in the solutionized and

Jan 1, 1970

By Inoue T, Takahashi N

To construct the accessing railroad line to the northern portal of Seikan Undersea Tunnel, nine tunnels amounting 7.4km in their total length were excavated through soft mudstones of young- er tertiary era with use of smaller-sized mechanic al excavators. Rocks were classified in four classes to which the tunnel support was designed respectively. Of several combinations of driving equipments stu- died comparatively, the method using the mechani- cal excavators was estimated to be the best choi- ce. The efficiency of the excavator was traced in every construction section and the data colle- cted was reviewed numerically. The result showed that the efficiency of the excavator dropped wh- ere the rocks were as hard as over 200kg/crif for compressive strength. And a few technigues in tunnelling i.e. contr- olling dusts in shotcreting, lattice arch, evaluati- ng measured deformations were tested and review- ed too.

Jan 1, 1987

By Randy R. Williams, Roberto R. Olivera, Brian W. Wilson, Marina S. W. Li

"An extensive, deep mixing (DM) ground improvement program using the Cutter Soil Mixing (CSM) technique was designed and constructed in 2013 to support up to 20 m (66 ft) high Mechanically Stabilized Earth (MSE) walls and bulk earthworks for the development of the Kitimat Liquefied Natural Gas (LNG) facility at Bish Cove, British Columbia. The deep mixing program consisted of overlapping rectangular panels of in situ cement treated soils, constructed using the CSM technique, to form barrettes covering an area of approximately 12,900 m2 (15,428 yd2) and providing suitable static and seismic stability of foundation soils for support of the proposed MSE walls, which would in turn support LNG facilities. The deep mixing program comprised of 1645 CSM panels that were constructed through varying thicknesses and discontinuous layers of very soft fine-grained marine deposits and/or loose sandy silt to silty sand deposits, embedding typically 2 m ( 6.6 ft) into dense silty sand to sand and gravel. CSM panel depths ranged from 5 m (16 ft) to 30 m (98 ft) and were constructed by treating approximately 73,900 m3 (96,658 yd3) of soil yielding average unconfined compressive strengths exceeding 2.5MPa (363 psi).This paper outlines the approach adopted for the design of the CSM ground improvement program in the highly variable subsurface conditions present at the site. A phased sitespecific investigation consisting of boreholes, test pits, Cone Penetration Tests, piston tube sampling, advanced laboratory testing and groundwater monitoring was implemented. In addition, soil-cement bench scale testing was completed, followed by installation of 8 CSM panels for field trial purposes. Extensive geotechnical static and seismic analyses including Limit Equilibrium stability analyses, liquefaction assessments, and advanced numerical modeling were undertaken to optimize the design and meet the project-specific design performance criteria. The Design-Build team worked closely to develop and implement Quality Assurance and Quality Control plans and managed significant construction challenges while achieving suitable panel termination depths."

Jan 1, 2017

By Michael G. Zabetakis, Aldo L. Furno, Henry E. Perlee

The Bureau of Mines conducted an experimental study with liquid and gaseous hydrogen to determine the hazards associated with the use of liquid hydrogen as an ionizing particle detector in bubble chambers . The glass window , the vacuum chamber , and the vent system were investigated . In addition , a study was made of the detection and ignition of escaping hydrogen and of the available electrical equipment for use in hydrogen atmospheres . Materials such as tempered glass , aluminum , and stainless steel are not penetrated readily by the small fragments formed when fully tempered glass is shattered and propelled by hydrogen at initial pressures up to 100 psig ; long , slender fragments from untempered glass may penetrate thin walls of relatively soft materials such as rubber gaskets and lead . Hydrogen can be vented satisfactorily from a vacuum chamber with a well - designed vent system . However , the rapid leakage of hydrogen into the surrounding air is a serious problem because the available detectors are satisfactory only when the accumulation of hydrogen is slow . Much of the electrical equipment currently available was designed for use in hydrogen- air atmospheres .

Jan 1, 1963

By William M. Sheehan

TRANSPORTATION is one of the most important problems of the mine operator and the possibilities of cost reduction in this field should not be overlooked. In the railroad industry, cars and locomotives have been improved greatly, and the progress there made is well worthy of study by the mine operator looking for maximum efficiency in every branch of his activities. One of the outstanding developments in the construction of railroad equipment in recent years has been the wide-spread adoption of large one-piece steel castings for the framework of locomotives, passenger and freight cars. Some of the advantages and applications of this type of construction will be outlined in this paper, with particular thought of the needs of the mining industry. The inherent qualities of cast steel: homogeneity, unrestricted size and shape, high tensile strength, flexibility of metal distribution, resistance to corrosion, and gracefulness of outline, make it the most versatile member of the ferrous group. Not only is it a strength-giving element, but it is corrosion resistant, a combination that makes for large economies in equipment maintenance. Flexibility of metal distribution allows the integral foundation to be in the shape best suited for the purpose. These cast structures are really assembled in the mold in liquid form and the metal can be placed in the right pro¬portion exactly where it is needed, thus securing weight economy and uniformity of fibre stress. Such a process permits the incorporation, with ease, of necessary brackets, utilizing them to provide not only greater strength for the derail part itself, but often to add to the value of the entire unit. Laps, seams, and joints, which are necessary in all fabricated forms, are eliminated.

Jan 1, 1933

By R. W. Geehan

The Yellow Pine zinc-lead mine, situated about 3-1/2 miles northwest of Goodsprings, Clark County, Nev., was explored by core drilling during the fall of 1942 and the summer and fall of 1944 by the Bureau of Mines in cooperation with the Federal Geological Survey. The Yellow Pine district was located in 1855. The original claims covering the Yellow Pine mine were located in the following years: Rover, 1892; Hilo, 1897; Bybee, 1900; Radio and Como, 1906. The mine was operated by the Yellow Pine Mining Co. from 1906 to 1929. This company was dissolved in 1935. At a later date, S. E. Yount and the Security First National Bank of Los Angeles, Calif., acquired ownership of the mine. Since 1939, the mine has been operated in a small way by leasers. Production has been at least 175,000 tons averaging about 10 percent lead and 25 percent zinc, with a gross yield of $5,785,174. Virtually all ore produced by this mine consisted chiefly of oxidized zinc and lead minerals and came from long, pipelike shoots in the 100-foot thick Yellow Pine limestone. Ore shoots are sharply defined; elsewhere, the limestone is nearly barren. Numerous faults cut the mine into blocks. Ore is now mined in an open stope, but in the past, large tonnages wore mined in stopes by square-set methods. Ore produced recently was shipped direct to smelters unprocessed; in the past, it was milled by gravity and produced separate lead and zinc concentrates.

Jan 1, 1949

By Y. R. Murthy, S. Angadi, A. K. Bhatnagar, S. K. Tripathy, L. O. Filippov

Dolomite is an essential raw material for the refractory industry, a flux in the iron and steel industry and also for the extraction of magnesium metal. Generally, particle size reduction, screening and classification are used for the preparation of the high-grade sized material for different applications, whereas low-grade fine fractions are not utilised. These fines or low-grade overburdens are dumped at the mine site for future utilisation, which creates environmental issues along with inadequate space management. In the present investigation, a detailed study was carried out to decrease the silica content of the low-grade dolomite fines from Gomardih , India, containing 28.6% CaO and 20.1% MgO along with 8.3% silica. Different process flow sheet options were evaluated with a combination of dry classifier, wet classifier, gravity concentrators as well as flotation. Different process variables were assessed along with mineralogical characterisation to optimise the process for efficient rejection of siliceous gangue minerals. Results indicated that dolomite, calcite and quartz are the major mineral phases present in the ore along with other minor minerals. It was concluded that two-stage flotation was an effective process for the reduction of silica up to below 1% after grinding to a particle size below 212 μm. A process flow sheet with a combination of gravitation air classifier and flotation can produce a concentrate with silica content below 4.5%. Keywords: Dolomite, flux, dry classification, flotation, characterisation, beneficiation

Jan 1, 2020

By M. Didyk

In this report, the application of the PHU/MVS program is demonstrated through the use of a simple but realistic mine ventilation program. The report details, the problem description, the input data required and the various output features of the simulator. The PSU/MVS program is written in Fortran IV for use with IBM 370/168 computers. A version of the program that can be used in CDC computers is also available. A ventilation network consisting of 531 branches, 300 nodes and 5 fans took 48 seconds for solution on The Pennsylvania State University's IBM 370/168 computer. Appendix I of this report is the User?s Manual for the program. Appendices II and III contain the input data listing, and selected output listing for; the application. Appendix IV provides tables for leakage, friction factors and shape factors.

Jan 1, 1977

By A. W. Storm

Vertical shaft furnace design and operation have their roots deep in antiquity. There is substantial evidence to indicate that iron was reduced from its oxides to serve mankind's needs long before recorded civilization - - actually prior to 3500 B .C. For at least 5500 years man has been matching wits with Nature to find better methods of extracting this most common, yet essential, metal from her, grasp. And, during nearly all of this period, the vertical shaft furnace has played a principle role in this dramatic struggle.

Jan 1, 1962

By Bobby P. Faulkner

The Tennessee Copper Co.'s flotation plant, refer- T red to as London Mill, processes approximately 4800 tons of a massive complex sulfide ore per day. The ore is predominantly pyrrhotite and pyrite, the other sulfides being chalcopyrite, sphalerite, and a small amount of galena. Magnetite of economic value is also present. There are four concentrates produced. In decreasing tonnage, these are iron, copper, zinc and lead. The ore feeding the mill is a composite of ores from five mines which vary in grade. Therefore, in order to provide a fairly constant feed to the mill, the ore is blended several times before reaching the flotation machines. The flotation plant is divided into three main sections: bulk, copper and zinc. Fig. 1 shows a simplified flowsheet. The first two sections, the bulk and copper, were the two sections studied most closely in utilizing the computer.

Jan 11, 1966

By U. Schoepf

Economic and at the same time environmentally acceptable mining of small vertical ore bodies and veins to great depths has always been a challenge for miners. The Bauer cutter system, widely used in civil engineering, has been further developed for applications in exploration and mining, to a sustainable system for selective mining with a focus on small vertical ore bodies and veins, as well as residual ore in open pit operations. Current situation of conventional mining of small ore bodies and vertical veins Small ore bodies and vertical or near-vertical ore veins often pose a challenge to the mining industry. The relatively small size of the ore deposit over great depths or lengths, with only limited exposure to the surface makes economical mining difficult. Open pit mining of such ore bodies must either be terminated early because of the high stripping ratio and the enormous environmental impact or is unprofitable from the very beginning. The required massive stripping of waste rock leads to high material hauling times and costs, intensive roadway and bench construction and maintenance, possible safety hazards due to heavy vehicle movement, pit wall stability risks, intensive surface water management and massive waste dump requirements. In addition, it can be assumed that increasingly extensive rehabilitation measures will be required in the future after mine closure. Particularly in vertically oriented magmatic and hydrothermal deposits the technical, economic and environmental limits for further pushbacks, to extend the open pit depth, can lead to an early end of mine life even if a significant quantity of residual ore is left behind. Going underground is only a viable option in a limited number of mines with very high ore values and volumes. The high development cost of an underground mine, as well as the higher underground mining costs, often prevent further mining to greater depths.

Feb 1, 2023