Search Documents

By Xin Zhang, Xu Zhang, Hao Bai, Ning Li

Organic Rankine Cycle (ORC) is an effective technology for low-grade waste heat power generation. In this paper, the thermal-dynamic performance of ORC system, in which low-temperature waste heat (from 40-140oC) is used as heat source, was evaluated with software RefProp8.0. The result indicates that in the range of low temperature, the working fluids like R601, R601a, R600a, R141b, R245fa and R245ca have better thermal performance. Furthermore, pilot-scale experiment using R245fa as working fluid was conducted, which validated the operation of the system for low-grade waste heat recovery. Finally, the economic feasibility of ORC has been analyzed for an ORC system using the waste heat from quenching water of blast furnace slag (80oC). According to the analysis, the project is reasonable in economy because the recovery period of investment is less than 4.2 years and environment-friendly since the CO2 emissions can be reduced by almost 43650.68t annually.

Jan 1, 2016

By Hubert Erik Sherer

Determination of the best time to replace an aging unit of equipment is a recurring problem which is common to essentially all surface and underground mining operations. Virtually all mining equipment is subject to wear and the resulting deterioration that increases with equipment life. This mechanical deterioration results in lower availability and, thus, decreasing, production. Due to decreasing production and increasing repair costs, there is an optimum age at which the replacement of a given equipment unit with a new unit will result in the lowest cost per unit of production for the equipment operation in question (Figure 1). Determination of this optimum replacement age is further complicated by factors such as: possible overhaul alternatives, fleet replacement and expansion alternatives, remaining life of the mine, and technological improvements in the potential replacement or differences in the production capacities of these replacements. Determination of the optimum time to replace an equipment unit becomes more critical each successive year due to the rising capital costs of new equipment versus maintaining old equipment. An incorrect choice of the replacement age for an equipment unit can result in excessive costs to the mining operation. If a unit is replaced too early, the capital cost of the unit is not fully utilized; conversely, replacing a unit too late results in excessive maintenance costs and low production. The economic life of a piece of equipment is the equipment age that results in the lowest total discounted cost per unit of production for that piece of equipment, not considering the cost of future replacements. The economic life of a piece of equipment is usually shorter than the physical life, the maximum age at which a machine is capable of doing useful work. The optimum replacement age for a piece of mining equipment may vary from the economic life of that equipment due to the remaining life of the mine, fleet considerations, costs associated with potential replacement machines, and capital rationing constraints. For example, the equipment life of the current machine that may result in the lowest cost per unit of production might be 10 years; however, when the timing of the future replacement costs are entered into the calculation, a different life for the current machine might result in the lowest total cost per unit produced for the remaining life of the mine.

Jan 1, 1982

"Previous studies on the effect of polytetrafluoroethylene addition during chalcopyrite leaching under conditions similar to those of the CESL process have reportedly resulted in complete leaching of the copper without the need for grinding of the flotation concentrate. However, these studies employed a pulp density of only 1% and finely sized PTFE particle that required the use of high impeller rotation rates that are not sustainable at an industrial scale. This paper explores the performance of 1/8” diameter balls of PTFE, that readily sink in the leach solution, on leaching performance at impeller rotation rates and ore pulp densities more typical of industrial practice. Possible routes for separation of the PTFE from the leach residues and their regeneration for recycling back to the leaching stage are also discussed.INTRODUCTIONChalcopyrite, CuFeS2, is the most important primary sulfide source of copper. While pyrometallurgical smelting of chalcopyrite remains the only widely accepted route for treating chalcopyrite concentrates, several medium temperature pressure oxidation processes are claimed to be economically feasible (Muir & McDonald, 2007). Among these, the CESL process has been extensively piloted and demonstrated at the prototype scale. The overall process chemistry of the CESL process may be summarized as follows (Marsden & Wilmot, 2007):4CuFeS2 + 5O2 + 4H2SO4 ? 4Cu2+ + 4SO4 2- + 2Fe2O3 + 8S0 + 4H2O (1)4CuFeS2 + 17O2 + 2H2SO4 ? 4Cu2+ + 10SO4 2- + 4Fe3+ + 2H2O (2)Though copper extractions of over 95 % are achieved, the CESL process requires extra grinding of the concentrate (Muir & McDonald, 2007). This is because leaching is conducted at temperatures around 150 °C, where the elemental sulfur produced is molten and grows thicker on the mineral’s surfaces as oxidation progresses, creating an increasingly large barrier for mass transport. In addition, the sulfur is sticky and tends to cause the mineral particles to agglomerate, effectively halting further oxidation of the particles that end up embedded within the agglomerates. Consumable surfactants, such as ligin sulfonate, have been shown to be effective at avoiding agglomeration, but they are not effective at removing sulfur from the minerals. Hence, their use does not obviate the need for fine grinding."

Jan 1, 2012

By Carlos Herrera, Paulo Alcazar, Alex Conco, Fremy Flores

Las redes neuronales artificiales son un subconjunto del machine learning y están en el corazón de los algoritmos de Deep learning reflejando el comportamiento del cerebro humano, permitiendo así que las soluciones tecnológicas reconozcan patrones y resuelvan problemas comunes en los campos de la IA. Este modelo matemático es capaz de aprender a través de un aprendizaje supervisado de patrones de conocimiento. Se investigó una solución que involucra cuatro tipos de sistemas.

Sep 30, 2022

By Monica R. Garcia, Antonio Alberto S. Correia, Paulo J. Venda Oliveira

"The aim of this paper is to analyze the creep behavior of a Portuguese soft soil stabilized with binders in one-dimensional conditions, based on oedometer creep tests. The study focuses on the analysis of the effect of the binder content and binder type on the creep behavior of a stabilized soil. The results show that the best binder type for this soil, in terms of creep behavior, is composed of Portland cement and fly ash with a dry weight proportion of 75/25, as this promotes the development of secondary pozzolanic reactions. The results also show the decrease in the secondary compression index with the increment of the binder content, since it promotes an increase in the cementation bonds between soil particles. The general analysis of the results shows a clear dependence on C??and qu, until values of qu of 1500 kPa; after that this relationship is negligible.INTRODUCTIONThe geotechnical structures (such as embankments, dams and buildings) built on organic soils exhibit notable creep deformations, which increase the maintenance and exploitation costs and can even compromise their functioning. To attenuate the creep effects of the soft ground, some improvement techniques are frequently used, such as preloading or reinforcing the soil foundations with vertical rigid inclusions, like concrete piles, stone columns or deep mixing columns (DMCs). However, the installation of DMCs in the soft ground induces (via the arching effect) a transfer of stresses from the soft soil to the DMCs, which causes an increase in the creep settlement on the DMCs (Venda Oliveira et al. 2011).Notwithstanding the fact that the creep behavior of clays has been the object of several studies (Leroueil et al. 1985; Mesri and Castro 1987; among others), the study of the creep behavior of soil-binder admixtures has been practically ignored by the scientific community. The few studies on this theme have revealed that a stabilized soil’s creep behavior is dependent on: the type of binder (Venda Oliveira et al. 2013), the binder content (Correia 2011; Bobet et al. 2011; and Venda Oliveira et al. 2013), the stress level applied during the creep phase (Venda Oliveira et al. 2013), the organic matter content of the natural soil (Venda Oliveira et al. 2012; 2014), and the curing conditions (humidity, vertical stress applied during curing, and curing time) (Correia 2011; Venda Oliveira et al. 2012).The aim of this paper is to contribute to a better understanding of the creep behavior of a soil-binder admixture, by examining the results of oedometer creep tests. The study focuses on the analysis of the effect of the binder content and binder type on the creep behavior of a stabilized soil. Additionally, the creep behavior is correlated with the effective vertical yield stress and the unconfined compressive strength (UCS)."

Jan 1, 2015

By Thomas L. Garrard, James A. Sprague, Rex B. McLellan, Samuel J. Horowitz

A simple rnodel for interstitial solid solutions has been devised in which each solute atom interacts with the solzlent lattice in such a way as to exclude an integral number of nearest-neighbor sites from being occupied by solute atoms. The vemaining interstitial sites ave not affected. In calculating the entropy of such a solution the increase in the number of interstitial sites available to solute atoms due to the ozlerlap of blocked sites is taken into account. The ther-modynamic functions and the solute activity fov the solution rnodel are calculated. It is shown that considevation of the overlap sues vise to a correction term of the order 8' ( where 0 is the ratio of solute to solvent atoms) in the thevmodynamic functions of the solution and the solute activity. The theo,uetical equation for the solute activity was used to analyze the available data for the activity of carbon in austenite at three different temperatures. The use of a computer enabled many comparisons to be made between the experimental activity data and those predicted by both the complex blocking model and the simple, widely used blocking model in which the ozierlapping of blocked sites is not taken into consideration. Even though at the highest concentvations oj carbon the value of 0 is small it is shown that the best fit to the experimental data is found with the complex blocking model. RECENTLY it has been shown by analysis of gas-solid equilibriums that many interstitial solid solutions can be described by the quasi-regular solution model in which the partial energy of solution E, is independent of composition and, apart from a composition-independent term due to nonconfigurational factors, the partial entropy is that of an ideal solution. Dilute solutions of nitrogen in both bcc and fcc iron,' dilute solutions of oxygen and silver,' carbon in a Fe,' and dilute solutions of carbon in ? Fe2 are all quasi-regular. In addition many hydrogen-metal solutions, both dilute and concentrated (with the notable exceptions of the H-Ni and H-Pd systems), can be described by this model.3 However, it has been shown that, at various temperatures, solutions of carbon in ? Fe begin to depart strongly from quasi-regular behavior at low concentrations. A plot of the activity of carbon in ? Fe relative to pure graphite vs atom fraction of carbon (Cc) calculated from Smith's data4 begins to depart from the (nonlinear) plot for a quasi-regular solution at about Cc = 0.02. Several statistical models have been proposed to account for the thermodynamic behavior of carbon in y Fe. Darken and smith4 set up a model in which a carbon atom in its octahedral site in the fcc lattice has either one or no neighboring carbon atoms in the twelve nearest-neighbor octahedral sites. It is assumed that the number of carbon atoms having more than one nearest neighbor is negligibly small and that a solute atom does not interact with another solute atom located at a greater distance than the first shell of interstitial sites. Thus this model contains two characteristic interaction energies. Darken and Smith showed that this model gives reasonable agreement with the measured variation of carbon activity ac with composition. It is noteworthy that Darken and Smith concluded from their analysis of the activity data using this model that there was a repulsive force between carbon atoms in austenite which reduces the concentration of C-C pairs below that corresponding to random mixing. Recently Aaronson, Domian, and pound5 have considered in detail the statistical model developed by Lachere and by Fowler and Guggenheim7 and have shown that it is compatible with the activity data for carbon in austenite. In Darken's model the energy of solution of carbon in austenite is dependent on temperature and concentration; the departure from Henry's law arises from the concentration dependence of the energy of solution. In Aaronson, Domian, and Pound's discussion of the Lacher, Fowler, Guggenheim model the interaction energy wy between adjacent carbon atoms in austenite is strongly temperature-dependent. Aaronson et al . suggested that this temperature dependence of wy and hence the energy of solution of carbon could be explained either by the formation of clusters of carbon atoms (despite the repulsive nature of wy) or by the dual occupancy of the octahedral and tetrahedral sites by the carbon atoms. However, a temperature-dependent heat of solution

Jan 1, 1968

By Michael L. Nave

Belt Conveyors are an important method for transportation of bulk materials in the mining industry. The control of the application of the starting torque from the belt drive system to the belt fabric affects the performance, life cost, and reliability of the conveyor. This paper examines applications of each starting method within the coal mining industry.

Jan 1, 1993

By Yessengaziyev Azamat, Almagul Ultarakova, Onayev Murat, Barkytova Botakoz

"The research is aimed at solving the processing of waste products of titanium-magnesium production. The aim of the research is to extract synthetic carnallite and industrial products enriched with niobium from waste products of titanium-magnesium production. Analysis of the current state of the titanium and magnesium production in the Republic of Kazakhstan shows the availability of significant amounts of chloride wastes containing valuable components. Magnesium and potassium with an average content of 50-60 % potassium chlorides, 25-30 % magnesium chlorides are lost in the wastes of the titanium and magnesium production. Ust-Kamenogorsk Titanium Magnesium Plant JSC (UKTMP) currently imports carnallite that is a KCl-MgCl2X6H2O binary salt at quite high prices. Chloride wastes of titanium production, sublimates of dust chambers of a titanium chlorinator, sludge of a magnesium electrolytic unit and sludge of a carnallite chlorinator has been chosen as the targets of our research. The analysis of niobium distribution within any solid waste of a titanium slag chlorination process in UKTMP JSC showed that the highest content of niobium is in the sublimates of dust chambers of a titanium chlorinator in the ranges from 0.26 to 1.0 %. Among the niobium extraction technologies considered, the known method of its extraction from the chloride waste is leaching with weak solutions of mineral acids or alkalis in order to convert the chloride salts into the solution to be used for synthetic carnallite extraction. Besides niobium, other impurity components are transferred to the cake and shall be separated from the base metals. The effective method for this is the chlorination process enabling niobium transfer into the sublimates in the form of chlorides and thus separating it from the majority of the impurities. The condensed niobium chlorides are hydrolyzed transferring it into sediments in the form of oxide. New ways of processing waste products of titanium-magnesium production with the receipt of marketable products are relevant in the development of processing of mineral raw materials."

Jan 1, 2018

By A. B. Parsons

LAST YEAR (1934) saw the completion of a ten-year program of reconstruction and modernization of the world's largest lead- smelting plant, that of the ' Broken Hill Associated Smelters Proprietary, at Port Pirie, South Australia, which has a capacity for smelting and refining 220,000 (short) tons of lead per year. It deals with the entire output of lead concentrates from the famous Broken Hill district in Australia, being owned .jointly by the three leading companies: North Broken Hill, Broken Hill South, and the Zinc Corporation. These companies, together with the Sulphide Corporation, are credited with a production of 198,000 tons of lead in 1934. When one says regarding any metallurgical plant that modernization is "completed" he should add "for the moment." Development in the art of metallurgy and in the equipment used never ceases; that which seems close to the last word today is likely to be obsolete in a few years even in a process so well standardized as smelting and refining lead. However, the reconstruction at Port Pirie has altered the procedure materially. More im-

Jan 1, 1935

By Rainer W. Kaiser

High wear resistant HSS rolls are being successfully used in the first stands of HSM finishing trains since the early 1990´s. The strong demand of mill administrators to make them applicable also in the last stands of the finishing rolling mill is a major influence factor of R&D efforts at respective roll suppliers. Looking back to the successful replacement of ICDP and HiCr rolls by more economic HSS rolls in F1-4 in regard to the TCO, rolling mill managers wish to repeat such scale gain also at F5-7 stands. Actually used enhanced ICDP rolls wear faster, being the HSM stoppage factor. F1-4 HSS rolls can be used for example 3 times longer. There is an obstacle to be overcome by roll suppliers and end users to replace F5-7 rolls by HSS rolls. Stick and crack resistance properties of HSS need to be improved. As a worldwide known leading producer of cast rolls for steel mills since 1820, the traditional German family owned foundry and machine shop IRLE, existing since 1693, accepted to face also this additional challenge. IRLE´s long year experience and prior researches have shown possible development directions to improve mentioned stick and crack resistance properties of its HSS grade, called SST. A new material of the HSS family is in the development pipe line and is discussed: SST/G. Choice criteria of the development direction, steps to control and guarantee respective sections of an industrial scale production as well as observations and results are described.

Jul 30, 2018

By J. S. Heath

Many disputes related to environmental issues in mining are resolved through often-antagonistic negotiations in a regulatory context or through litigation. These approaches are certainly the best choices for resolving certain disputes. However, just as no single remediation technology is the right fit for every site, so no single dispute resolution process is the best choice for every situation. This paper introduces a range of dispute resolution alternatives (from collaborative decision making through mediation, arbitration, and litigation). Especially when money is tightest, cost-effective dispute resolution(and the outcomes that can accompany it) can have an impact on the bottom line.

Jan 1, 2000

By V. I. Lakshmanan

"Historically flowsheets are developed for efficient separation of metals for economic recovery. With increasing emphasis on reduction, reuse and recycle (3Rs) efficient methods are sought to recover values from a variety of feeds where cost of collection, transportation, local consumer behaviour and regulatory guidelines dictate the development of economically viable flowsheets. Innovative understanding of potential market applications can provide means to develop value added end products. The paper with examples will discuss the use of innovative-separation technologies to obtain value added end use materials from secondary sources.IntroductionFlowsheets are developed for the efficient separation of materials of value for economic recovery. However with increasing societal pressures and regulatory initiatives for stricter environmental guidelines, there is strong need to provide focus to recover materials efficiently and economically in an environmentally accepted manner. North American industries are increasingly caught between demands for high technology value added products and responsibility for environment. An aspect that is receiving increasing attention is Design for Environment'. This incorporates a system wide approach for product design and incorporates environmentally preferable features such as recyclability, disassembly, maintainability, reusability and use of safe materials as part of a product's design objectives.The present paper with case histories will address innovative flowsheet development to convert wastes into recyclables value added products or for minimising generation of waste materials. Case HistoriesProcess for Separating Fibres from Composite Materials 1In the automotive industry, sheet molded compound (SMC) is used to produce panels, bumpers and the like. During the manufacture and at the end of life, considerable waste materials are generated which are potentially recyclable. Fibre reinforced plastics where fibre substrate impregnated with thermosetting resin, find applications in several manufacturing processes and are potentially recyclable at the end of life."

Jan 1, 1996

By W J. Shaw

Mining operations must become more predictable to overcome the volatility that has characterised the mining industry. Comparisons of production against predictions will become more consistent as mining operations merge and expand, as personnel move from site to site, and as public reporting of reconciliations becomes more prevalent. More consistent approaches are already being seen in the industry using the terminology used in this paper and elsewhere.Examples are provided that show how use of the waterfall chart as a reconciliation management tool can provide objective analysis to improve practices.Geometallurgical modelling is becoming more useful and will continue to do so as we move from a few bulk samples to better interpretation of material properties from geological mapping and drill sampling. Reconciliation has evolved to the stage where predictions of geometallurgical properties to optimise mill performance, and of geotechnical properties derived from better 3D geological models, should also be reconciled.CITATION:Shaw, W J, 2014. Reconciliation – outcomes and expectations, in Proceedings Ninth International Mining Geology Conference 2014 , pp 123–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By Xie Junjie, Li Shina, Ma Ruixin, Min Changli, Yin Zichen, Li Kang, Shi Zhuonan

Cesium and rubidium were effectively separated by zinc ferrocyanide coprecipitation method, and the effect of precipitant addition amount on the separation of cesium and rubidium was studied. Under the conditions of Zn/Cs molar ratio of 0.45 and Zn/Fe molar ratio of 1, the precipitation rate of cesium is 84.01% and the separation factor of Cs/Rb is 164.65. The thermogravimetric curves of the sediment were measured, and the effects of roasting temperature, roasting time, and leaching liquid/ solid ratio on the extraction of cesium were studied. Almost all of the cesium was extracted under optimal conditions: roasting temperature of 600 °C, roasting time of 3 h, leaching temperature of 25 °C, leaching time of 0.5 h, and liquid/solid ratio of 5:1 mL/g. After the leaching process, the leach liquor with high concentration of cesium of 80.17 g/L was obtained. Finally, the leach liquor was further purified by solvent extraction, and the purity of the cesium chloride product reached 99.66%.

Mar 17, 2024

By Nick D. Rose

The Dy deposit is a 21 Mt Pb-Zn-Ag-Au SEDEX-type massive sulphide resource located in the Anvil District, Faro, Yukon. This relatively unexplored orebody lies at a depth of 480 to 920m below surface, dips 20 to 35o and comprises vertical ore thicknesses of 3 to 28m at a 9% Pb + Zn cut-off grade. The deposit has been tested at depth with 63 surface diamond drillholes, but has not yet been explored or developed by underground means. Over the past decade, pre-feasibility investigations were conducted for two separate owners of the property to determine the economic viability of developing an underground mine at Dy. Following these previous studies an assessment was undertaken between 1998 and 2000 to further investigate geotechnical considerations for underground mining. The results and conclusions drawn from this study provide direction for possible future exploration at Dy.

May 1, 2002

By Georges J. Kipouros

Anhydrous neodymium trichlorids (NdCl3), containing ~1 weight percent neodymium oxychloride (NdOCI) was prepared by the dehydration of neodymium trichioride hexahydrate (NdC13.6H2O). Dehydration of the hexahydrate was conducted in three steps. First, the hexahydrate was slowly heated in air to about 250 °C until all the low temperature water of crystallization was removed. In the second stop, the neodymium hydroxychloride (Nd(OH)2C1) fanned in the first step was decomposed by heating under argon to 430 ° C. Finally the salt was ground and then treated with HCl gas at 330 °C until practically all of the NdOCl was converted to NdCl3.

Jan 1, 1992

By E. Bakhtavar

It is considered that the most economical method for the exploitation of Gol-e-Gohar Area 3 iron ore mine is to combine open-pit and underground methods. In this regard, the most critical problem is the determination of optimal final pit depth. In this paper, a method which was recently introduced on the basis of economical block models of open-pit and underground is used to determine optimal final open-pit depth of Gol-e-Gohar Area 3 mine with due regards to the future underground mining option. Considering a low cost and productive underground method as a feasible alternative for extraction of the lower part of this deposit, room and pillar was selected. It is concluded that after the assessment and comparison of different values for depth, optimal final open-pit depth was determined to be equal to 285 m.

Jan 1, 2010

By A. W. Ambrose

The present plans for the Petroleum Division of the American Insti-tute of Mining and Metallurgical Engineers provide for two principal meetings in the year 1928. The first will be at Tulsa, Okla., in September or October, 1928, with the exact date largely dependent upon the date of the .International Petroleum Exposition. The officers wish to hold the meeting at the same time as the Exposition in order that members of the Petroleum Division of the A. I. M. E. may have the advantage of attending both meetings at the same time. It is planned that this meeting will be devoted largely to petroleum production engineering problems. A tentative outline of subjects to be discussed is as follows: 1. Repressuring New Oil Fields, and naturally in conjunction with this falls Repressuring of Old Fields. 2. Air or Gas Lift. 3. Flow Strings in New Wells. 4. Deep Drilling Technique. It is also planned to have at this meeting a general paper relating to Supply and Demand of Petroleum and its Products. The second meeting is planned for February, 1929, in New York at the same time as the annual meeting of the Institute. Special details have not been carried very far on this meeting, although it is expected the program will cover technical problems in relation to production and refining of crude oil, as well as 1928 development in foreign fields and the United States. It is planned during 1928 to cooperate with the Bureau of Mines in an attempt to compile a set of definitions on petroleum engineering. These would be of value to the petroleum engineering profession, in order to better standardize various terms used in discussion of current problems. It has also been suggested that the Petroleum Division study certain problems in which research work is needed by the petroleum industry and outline certain definite programs that could be carried out by the Bureau of Mines and the U. S. Geological Survey, as a follow-up to

Jan 1, 1928

By W. Mirihange

Considerable mechanical property decline is always observed at the Heat Affected Zone (HAZ) of AA 5083, This occurred as a result of the thermal effect on the hardened material, It is highly beneficial to have a prospective metallurgical procedure to overcome this decline of properties. Therefore, experiments were set to evaluate the effectiveness of a quick post weld heat treatment process with the AA 5083, Optimum results were obtained at 473K and with approximately 600 seconds time, The interplay between the time, temperature and mechanical properties are possible to explain by the Lifshitz-Slyozov-Wagner (LSW) theory and by considering the composition of the material.

Jan 1, 2005

By C. E. Gregor

Current modern trends in mining show that hoisting shafts are being expected to fulfill an important ventilation function. However, where rigid guides and supporting structures are mandatory, ventilating power costs will be high, unless the transverse structures (shaft sets) are streamlined. In the complex configurations of hoisting shaft furniture patterns, either for original design purposes, or for the adjustment of an existing shaft, a useful degree of aerodynamic optimization, by reduction of overall resistance, can only be effectively evaluated by model studies in a special purpose wind tunnel, as described herein. The author has shown that, in one particular case, an annual power cost saving of more than $50,000 was indicated, mainly by the selection of buntons and dividers of improved aerodynamic profile. Mining companies are now realizing the advantages that can accrue through proper attention to the aerodynamic aspects of mine shaft design. With progressive demands of civilization for an ever greater supply of coal and metals, and with greater depths of working, higher rates of extraction, advanced degrees of mechanization, and improved standards of environmental health and work comfort, shaft design is becoming an extremely important aspect of mining operations. In addition, because the cost of sinking, equipping, maintaining, and operating a mine shaft is continually increasing, there is a greater incentive to use a shaft for the maximum duty, consistent with economy. The current natural tendency is therefore to sink multi-purpose shafts, to install as much equipment as is safely and effectively possible to operate; and then, over and above all these functions, to use the shaft to its maximum possible ventilating capacity, as a major, or auxiliary, airway. Clearly, this latter additional function can only be employed at a significant cost, since the most economic operating airways are smooth-lined and devoid of internal rigid furniture. It is true that hoisting functions can be carried out in such shafts if rope guides are used, but only under restricted conditions. Where a manway must be provided, fixed guides and supporting structures are mandatory, and ventilation costs become accentuated. It is generally recognized that the prime element of cost in ventilating a mine can be represented by the power required to drive the fan unit. It is also known that the largest component of total mine resistance is that of the downcast shaft, where this shaft is equipped with rigid guides for hoisting purposes. The pressure loss varies directly as the resistance of the shaft, in accordance with a modification of the Atkinson equation p = RQ2/3600. Furthermore, the air horsepower drawn is given by the equation AHP = (p x 0/33000. Therefore, the power required to drive the fan unit varies as the resistance of the shaft and the cube of the air quantity. Clearly, if Q is a specified minimum, then the only way to minimize the pressure loss (and the power costs) is to reduce the shaft resistance R. (See Table I for a list of symbols.) The resistance to airflow of a shaft equipped with rigid guides and supporting structural sets consists of two components which, for the sake of analytical simplicity, can be regarded as additive. 1) Frictional resistance, represented by the viscous frictional forces within the boundary layer, as air flows along the surfaces of the walls and the periphery of the vertical elements (guides, pipes, cables, ropes, etc.) of the furniture. The friction loss can be readily calculated by the Atkinson equation, after selection of a suitable value for the friction factor K from the McElroy compilation.' KxLxO xQ2 5.2 xA3 Friction loss can be minimized by lining the shaft walls (particularly if of circular or elliptical cross-section) with a smooth continuous lining of monolithic concrete.

Jan 1, 1968