Search Documents

By David B. Costain

Three dimensional surface approximations are important means of evaluating physical and environmental factors that affect surface coal mining and reclamation. Computer approximated surfaces are projected as an array of square grid cells where individual cells define each parameter value respective to locations on the grid. Grid surfaces or grid cells within a surface can be compared or modified through application of standard mathematical functions. Surface approximations can be used to define the quantity and quality of marketable coal and to evaluate thickness and quality of overburden. Surface approximations also can be used to evaluate overburden swell factors wherein changes in post-mine topographic relief are related to expansion of unconsolidated materials in the backfill. Application of computer approximated surface to analysis of approximate original contour (AOC) standards allows an assessment of the quantity and geographical displacement of overburden and the distribution and numerical level of slope.

Jan 1, 1984

By Audrey Wagenaar

Introduction ?? Rising public pressures are being placed on companies worldwide to protect the environment and the health and safety of their workers and local communities. ?? International bodies and shareholders want to make sure developments and companies can meet internationally acceptable standards for EHS. In 2005, Golder Associates was asked by the IFC to conduct a comprehensive review and update for their Environmental Health & Safety Guidelines including the mining sector.

May 1, 2008

By R. A. Thomas, C. D. Litton

"The objective of this study was to develop a laboratory-scale method to rank the ignition and fire hazards of commonly used underground mine materials and to eliminate the need for the expensive large-scale tests that are currently being used. A radiant-panel apparatus was used to determine the materials’ relevant thermal characteristics: time to ignition, critical heat flux for ignition, heat of gasification, and mass-loss rate. Three thermal parameters, TRP, TP1 and TP4, were derived from the data, then developed and subsequently used to rank the combined ignition and fire hazards of the combustible materials from low hazard to high hazard. The results compared favorably with the thermal and ignition hazards of similar materials reported in the literature and support this approach as a simpler one for quantifying these combustible hazards. Resumen ¦ El objetivo de este estudio fue el desarrollo de un método a escala de laboratorio con el fin de clasificar los peligros de ignición y fuego de materiales comúnmente usados en minería subterránea y la eliminación las pruebas costosas y a gran escala que se realizan actualmente. Se usó un aparato de panel radiante con el fin de determinar las características térmicas relevantes de los materiales: tiempo de ignición, flujo de calor crítico para ignición, calor de gasificación y tasa de pérdida de masa. Se derivaron tres parámetros térmicos de los datos: TRP, TP1 y TP4, luego fueron desarrollados y subsecuentemente usados para clasificar los peligros combinados de ignición y fuego de materiales combustibles, de bajo riesgo a alto riesgo. Los resultados tuvieron una comparación favorable con los riesgo/peligro térmicos y de ignición de materiales similares reportados en la literatura y apoyan este enfoque como uno más simple para la cuantificación de estos riesgos combustibles"

Jan 1, 2015

In this paper, geostatistical techniques are applied to forecast the annual copper price in the short and medium terms (from one to five years ahead). These techniques allow the incorporation of monthly and multivariate information in the analysis and provide more accurate results than traditional approaches, especially as far as the one-year forecast is concerned. A second advantage of geostatistics stems from its ability to assess the uncertainty associated with the unknown future prices, thanks to estimation variances or confidence intervals, depending on the technique used. Such an assessment has a crucial importance in decision-making, from both macroeconomic and microeconomic points of view

Sep 1, 2004

By P. Amelunxen

It is well-known that the particle breakage mode that occurs in a semi-autogenous mill is significantly different from that which occurs in a ball mill, enough so to warrant very different lab scale breakage tests and scale-up models. This phenomenon, at the plant scale, leads to changing process constraints depending on the particular properties of the ore. For example, hard or coarse ores might bottleneck the SAG/AG mill throughput, while the ball mills might constrain throughput when milling soft or fine ores. Because the power draw of a ball mill is fairly constant compared to that of a SAG/AG mill, periods of SAG/AG mill bottlenecks lead to increased ball mill circuit specific energy consumption and a finer grinding circuit product size, which together constitute a loss of efficiency of the overall process. Because HPGR circuit throughput is less sensitive to changes in ore hardness, this situation is less common or severe in those circuits. Furthermore, the ball mills are somewhat decoupled from the upstream crushing circuits through the use of surge bins, which also helps to mitigate this effect. As a result, ore hardness variability constitutes a significant cost penalty that should be applied to SAG mill/ball mill/pebble crusher SABC circuits when evaluating the relative economics of different grinding circuit configurations. Nevertheless, the issue is by-and-large ignored, because most current HPGR trade-off studies are based on averaged ore hardness parameters. This paper provides an estimate of the magnitude of this penalty for a typical operation by using Monte Carlo simulation methods and plant data from Freeport-McMoRan?s autogenous, semi-autogenous, and HPGR-based comminution circuits. A case study from an in-house 96K t/d sulphide project is presented to illustrate the concept. It was found that by including variability effects, the trade-off NPV of the HPGR circuit over that of the SAG mill circuit increases to $84 million from negative $33 million, effectively reversing the original decision of selecting a SAG mill circuit for the fixed hardness case.

Jan 1, 2012

By Daniel E. Sullivan

This Bureau of Mines publication examines the potential impact on minerals of the tariff and nontariff agreements that resulted from the Tokyo Round of the Multilateral Trade Negotiations, which were conducted under the auspices of the General Agreement on Tariffs and Trade. These agreements will affect minerals by reducing tariff levels and by changing rules by which they are traded internationally.

Jan 1, 1981

By A. S. Macfarlane

This paper describes how knowledge of the orebody morphology and ore morphology can be used to optimize the planning, mining, and metallurgical output from an open pit copper mining operation, such as to significantly increase the stability of the whole value chain process, and increase the reliability and value of the process outputs. In the case under consideration, the orebody contains both copper and cobalt. This in itself provides a challenge, in that the two metals do not occur in consistent ratios across the orebody as a whole. Furthermore, mineralogical differences within the orebody have a significant impact on plant performance in terms of throughput rates, acid consumption, and recoveries. In order to stabilize and optimize the plant performance, it is necessary to firstly have a complete understanding of the geometallurgical factors that affect performance, and then to have a sound knowledge of how these are distributed within the orebody. These models then inform the mine planning strategy that optimizes cash flow and NPV, and also allow the development of a stockpiling strategy that not only stabilizes the plant, but also allows variations in the plant feed according to ore type and grade in volatile price scenarios. Integral to the realization of these opportunities is the establishment of an appropriate measuring, control, and reconciliation system, customized to the optimization objectives. The paper describes how all of these factors and strategies can be integrated to produce optimal value from the orebody through to final dispatched product. It also shows the significant value that can be released through such an approach.

Jan 1, 2014

By A. Zarei-Hanzaki, O. Golmahalleh, S. M. H. Hosseini, H. Azizi-Alizamini

The main importance of acicular ferrite microstructures arises from their desired combination of mechanical properties in comparison with the bainite and ferrite-pearlite microstructures. Several factors affect the microstructural transition from bainite microstructure into the acicular ferrite one. As is well established any factor corrupting the prior austenitc grain boundaries nucleation potential, such as the thin layer of allotriomorph ferrite and the austenitc deformation inhomogenities may promote the acicular ferrite formation instead of bainite. Accordingly, this study deals with the effects of the aforementioned features on the acicular ferrite formation in low carbon microalloyed steel. The results indicate that the formation of strain-induced ferrite at the prior austenite grain boundaries accompanied by deformation inhomogenities in the austenite grains change the effectiveness of allotriomorph ferrite on acicular ferrite formation from active to inert one.

Jan 1, 2004

Objective To develop safety training tools for mine safety and health trainers that can be used for both new-miner training and annual refresher training. Background For the past 3 years, NIOSH has been developing training materials for mine safety trainers in response to gaps identified during stakeholder meetings. Most materials have been directed to the hazards of underground mines, but the recent passage of Part 46 of CFR 30 required new-miner and annual refresher training in aggregate operations. One result was the identification of another audience needing basic information about safety in mining. Trainers characterized trainees in this segment of the industry primarily as young males, many of whom had little work experience. Approach Training specialists from the Arizona State Mine Inspector’s Office approached NIOSH researchers early in2002 about the possibility of a collaborative project to develop safety training materials for new trainees in aggregate operations. A preliminary search of MSHA accident statistics identified over a dozen common hazards that could be targeted in a training video. A storyline was developed for review by safety specialists in the aggregate industry, and a script was written to cover the selected hazards. Although the target audience was primarily new hires, the finished video was also to be relevant to more experienced workers.

Jan 1, 2003

By Robert K. Linn

The New ldria Mining District is in the southern part of the Diablo mountains of the California Coast Range, 140 miles southeast of San Francisco. The district, noted primarily for quicksilver, also has become important recently as a producer of short-fiber chrysotile asbestos. Between 1853 and 1966, the New Idria district produced 568,092 flasks of quicksilver valued at about $55,600,000, 99 per cent of which was recovered from one deposit, the New Idria mine. In 1944, the district was ranked third in all-time production of North American quicksilver districts, and, since that time, the New Idria mine produced an additional 129,045 flasks, placing the district and the New Idria mine second in all-time production. The major structure of the region is the northwest-trending Coalinga anticline consisting of an asymmetric dome of sedimentary beds ranging in age from Jurassic to Quaternary and marked at its northwest end by an oval body of sheared serpentine 14 miles long by 4 miles wide. The serpentine core, rimmed by Franciscan sandstone of probable Jurassic age, was uplifted in stages between Jurassic and Quaternary time and was intruded along a ring of faults into beds of the Panoche Formation of upper Cretaceous age. The core of serpentine and Franciscan rocks is the locus of about 20 quicksilver mines that rim the faultbounded core and lie within the serpentine mass. The host rock of the most productive deposits is altered Panoche shale and sandstone that lies intermittently along the perimeter of the core. Deposits of the New Idria group of mines and those of a few other small mines lie along the northeast contact in the footwall of the New ldria thrust fault, and a few others occur on steep normal faults around the south and southwest. The chief ore mineral in all quicksilver mines is cinnabar, but minor amounts of metacinnabar and native mercury are found in some of the mines. Ore shoots were deposited in fracture zones and stockworks in altered Panoche shale and sandstone and in definite fissure veins in Franciscan sandstone. Rocks made highly amenable to fracturing by hydrothermal alteration were fractured extensively by late faults. The resulting fracture zones, located along the late faults and at changes in strike or dip of the hanging wall or footwall, are the principal controls of most ore shoots. The largest and richest ore shoots are those of the New Idria mine. The major ore bodies occur in fractured shale and sandstone beneath the New ldria thrust fault at its junction with major tear faults.

Jan 1, 1968

By Dominic Parmantier, Karen Dawson, Suthan Pooranampillai, Seungcheol Shin

"This paper presents a case study of the use of single axis cement deep soil mixing (CDSM) to deal with static settlement and seismic stability of the foundation soils under a reinforced soil slope (RSS) embankment up to 50 feet high. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter-bedded with silty sand layers and organic silt where identified as being potentially liquefiable. CDSM was selected to address the embankment foundation concerns and allow for future trenchless installation of utility lines beneath the embankment. The presence of a confined, artesian aquifer within the design depth of the CDSM led to the installation of a depressurization system to avoid an upward gradient through the wet soil-cement. In addition to addressing the design approach, the paper discusses the challenges associated with quality assurance of CDSM within the time constraints of an ongoing project. The limited recovery rate of conventional triple tube coring in the soil-cement and double tube wet sampling led to the use of sonic coring to provide a near continuous core of the soil-cement.IntroductionCement deep soil mixing (CDSM) was used as a replacement for stone column ground improvement in a corridor which the owner, the Washington State Department of Transportation (WSDOT) wanted to reserve for future trenchless crossings beneath reinforced soil embankments within a freeway interchange. The work was part of HOV improvements to I-5 in Tacoma, Washington. The CDSM construction occurred in late 2010 and early 2011.Approximately 14,500 cubic yards of soil cement columns were placed by CDSM. The soil cement improved ground supports permanent geosynthetic reinforced slopes up to 50 feet high. The ground improvement was designed primarily to provide global stability of the reinforced slopes during seismic loading, but it was also utilized to reduce the time and total amount of settlement following construction of the embankments.This paper presents a discussion of the design approach and challenges associated with quality assurance of a relatively small volume of CDSM within the time constraints of an ongoing project. The challenges associated with attempts at collecting cores of the cured soil-cement mix cured by triple tube coring and pushing a double tube into the wet mix and allowing it to cure insitu are discussed, along with the eventual adoption of sonic coring combined with reliance on laboratory testing of wet mix samples collected daily."

Jan 1, 2017

By J. Boldy

The discovery of the Delbridge massive sulphide deposit in the Noranda district of Quebec resulted from an appreciation of the significance of a mercury leakage halo as a litho-chemical pathfinder to blind ore, coupled to its location relative to a geologically inferred ore-bearing horizon within complex volcanic stratigraphy. Systematic sampling of micro-fractures present in outcrops delineated a diagnostic anomaly, drawing attention to an area considered prospective for buried ore. The massive sulphide deposit was subsequently found to be blind and topped at the 110 metre level.

Jan 1, 1984

By C. A. LINDBERG

Several new methods have been developed on the Iron Range to remove the material adhering to truck bodies in freezing weather. A machine known as a Gradall, incorporating the features of digging both above and below the horizontal, digging angle of blade control, full revolving, travel almost anywhere, and operated by one man, has proven successful in trials at body cleaning. Several of these units are in use with great saving in box-cleaning costs and improvements in efficiency of the truck operation with full capacity boxes. In addition to their winter use, the same machines have been used for ditching and excavating in the summer with great saving. The latest method of combating this freezing problem is to carry the exhaust from the engine through the body, making use of the tremendous heat that is now being wasted. To do this, the present wood sandwich which is used between the bottom of the box and the wear plate is removed and replaced with angles or channels run lengthwise of the box and spaced to permit gases to flow between or through them and also provide a good sup- port for the wear plate. The channels or angles are cut a little short on each end to form a cross passage that permits the gases to flow through the area. In the front end, openings are made in the wear plate and connect to a manifold created by welding a plate across the whole front of the box, spaced from the original end by the original vertical reinforcing angles at that point. The body being described is for a Euclid truck which is the only truck that has been adapted to this body-heating idea to date. At the rear of the truck, the holes from the cross passage are made in the bottom plate of the body and lead into a triangular-shaped body cross member under the scoop end of the truck.

Jan 1, 1949

By M. Rafieazad, P. Fathi, M. Mohammadi, A. M. Nasiri

This study examines the impact of low-temperature heat-treatment cycles on microstructure and corrosion performance of Direct Metal Laser Sintered (DMLS) AlSi10Mg_200C alloy. It is known that the morphology and the size of eutectic silicon are the two most critical factors affecting mechanical properties of the AlSi10Mg alloy. Although high-temperature heat-treatment cycles are common practice for the strengthening of the cast Al-Si-Mg alloys, in the case of DMLS fabricated AlSi10Mg alloy, high-temperature solutionizing and low temperature annealing cycles result in mechanical properties degradation primarily due to a dramatic decrease in the solubility of Si in the super-saturated a-Al matrix of the as-printed alloy. In this study, low-temperature heat-treatment cycles that only promote precipitation of Mg2Si accompanied by the interruption of the silicon network were investigated. SEM and XRD analysis were utilized to observe the evolution of microstructure after different annealing heat-treatments at 200, 250, 300, and 350°C for 3 h. Increasing the heat-treatment temperature contributed to the Si networks interruption and an increased precipitation of Mg2Si phase. Low-temperature annealing from 200 to 350°C was found to promote the homogeneity of the microstructure characterized by a uniform distribution of eutectic Si in ??-Al matrix. Additionally, in order to investigate the impact of different heat-treatment cycles on corrosion resistivity of DMLS-AlSi10Mg_200C, the potentiodynamic polarization testing and electrochemical impedance spectroscopy were performed in a 3.5 wt.% NaCl solution. The results revealed more uniformly distributed pitting attack on the corroded surface by further increase in the annealing temperature, which was attributed to the uniformity of Si dispersion. In comparison, low temperature annealing at 200°C led to a penetrating selective corrosion attack along the melt pool boundaries, resulting in a higher corrosion rate associated with the lower absolute value of impedance of the protective passive film on the surface.

Jan 1, 2018

By E. Grygiel, J. Haynes, T. McNider

Jim Walter Resources Blue Creek No. 3 Mine was opened in one of the most gassy coal beds in the United States. Although face ventilation requirements exceeded 14,000 cfm (6 .6m3/s) air, continuous miner sections experienced an unacceptable frequency of frictional ignitions. Modifications offered primarily by the U. S. Bureau of Mines such as diffuser fans, water spray fans, and slow speed cutting motors were used with little success. However, laboratory tests conducted at the U. S. Bureau of Mines indicated that an increase in bit attack angle from 50° to 55°-57° significantly reduced the chances of the bit causing a frictional ignition. An experimental miner drum was built using this concept coupled with a new bit designed by the Bureau and manufactured by Hughes Tool Company that better protected the bit steel shank with a carbide cap. It was installed on a continuous miner and placed in an area of the mine prone to ignitions. 50,000 tons (45,500 metric tons) of coal were cut without a frictional ignition. When the miner was withdrawn for rebuild and a machine with an unmodified cutting drum placed in service, two ignitions occurred before 10,000 tons (9,100 metric tons) were mined. Other machines have been rebuilt and are in service, and to date none have been known to cause an ignition.

Jan 1, 1987

By AIME AIME

THE difficult problem of visitors is being met by the Hudson Coal Co. at Scranton in an ingenious fashion. The Company had long made it a point to have dealers selling its coal visit the mines, whenever possible. "The excellent reaction obtained from these dealer visits brought up the question of whether it would not be possible to open one or more mines to the public, and give the consumer an opportunity of seeing for himself how anthracite is mined and prepared. Ac-

Jan 1, 1929

By Samuel S. Wyer

The art of natural-gas compressing is now over 25 years old, and has grown at practically the same rate as the increase in domestic natural-gas consumers. There are now over 200 natural-gas compressing stations in North America, aggregating more than 320,000 hp. of compressor capacity and representing a property value of more than $22,000,000, and compressing more than 85 per cent. of all the gas used. The age and magnitude of the art make it evident that the use of gas compressors is a recognized integral part and universal custom of the natural-gas business. The public also is not without its rights and vital interests in this problem. Approximately 1,700,000 domestic natural-gas consumers in North America are dependent upon gas compressors for their natural-gas service. That is, if the use of compressors were to be prohibited, the majority of these consumers would be unable to secure adequate natural-gas service. Each consumer represents between four and five persons, and it therefore follows that the comfort and well-being—as far as natural-gas service is concerned—of at least 8,000,000 persons would be affected if the use of natural-gas compressors should be prohibited. These 1,700,000 consumers have invested, in services, house piping, fixtures, and appliances, an average of about $90 each, or an aggregate of $153,000,000, which is much more than the companies' investment in gas compressors. Furthermore, in all cases where the rate paid by the consumers is fair to the gas company—considering the value of the service rendered by the gas company—the consumers are entitled to continued service and protection of the investment they have made on the faith that the gas service would be continued in the future. Since "Customs adopted and acquiesced in, if not in conflict with federal or State legislation, have the force of positive law,"l and ('Courts will take notice of whatever ought to be generally known withxn the limits of their jurisdiction,"2 there ought to be no question as to the un-

Jan 1, 1916

By John Birkinbine

THE favor with which the members of the Institute received Mr. Fernow's paper upon the use of charbon roux in the manufacture of iron has encouraged me to present this paper, in the hope of having the discussion upon the manufacture and use of the oldest and undoubtedly the best fuel for producing pig iron continued. Owing to the advances made in employing anthracite coal, bituminous coal, or coke, or mixtures of them, we are apt to forget how much of our present development is due to the pioneers in iron manufacture and the fuel which they employed in the production of pig iron. In Mr. Swank's last compilation of the iron and steel works of the United States, the furnace capacity of the country is given as 5,868,000 tons, of which 1,000,000 tons can be made in the 264 charcoal furnaces. In other words, over one-third of the furnaces now in existence use charcoal for fuel, and produce more than one-sixth of the iron made. If to this is added the 130,000 tons of blooms and billets turned out by the 122 forges and bloomaries, the importance of the charcoal industries will be appreciated.

Jan 1, 1879

By Ludwig Schmidt

The disposal of the brines produced with crude petroleum and natural gas has long been a constant source of trouble to oil and gas operators as well as to farmers and stock-raisers in the vicinity of producing fields. The amount of oilfield brines Produced from wells on new properties may be almost negligible, but some older wells may produce several hundred barrels a day. A survey of almost 200 wells on 31 properties in the eastern part of Osage County, Okla., showed that during the month of November, 1928, the average production of water was 3.26 barrels per barrel of oil produced. The age of the wells included in this survey ranged from two to 28 years; the maximum amount of brine produced was 26 barrels of water to one barrel of oil and the lowest was one barrel of water to 27 barrels of oil. These figures apply to a small area. In other fields the production of water also varies widely; for example, in the Cushing4, Okla., field several yells were reported as having produced 100 barrels of water to every barrel of oil produced. Often the production of oil-field brines is decreased materially and the production of petroleum increased by the use of bottom hole Plugs and by a general repair and cementing of wells. The records5 of 22 wells cemented in the Gushing field showed that prior to the repair work, the average total dally production was 242.5 barrels of oil and 3,977.5 barrels of water. The total Production of

Jan 1, 1929

By Cheri Eby, William R. Eby

INTRODUCTION Pneumatic conveyance systems provide for material placement at high compaction rates in confined spaces. This method of conveyance provides proper roof support and ground stabilization important to underground mining activities. Today underground mining activities are conducted far differently than those of our ancestors, in that the reclamation process is the final step in any mining activity. Responsible mine owners are constantly seeking innovative methods to assist them in their reclamation procedures. During the last few years, particular attention has been paid to previously mined areas, as many of these abandoned areas lay open, imposing a constant threat to humans and animals. Considerable attention is being directed to applying proper methods for the filling and sealing of underground slopes, drifts, tunnels, and adits, because today we are experiencing the effects of past mining activities such as subsidence, acid mine water run-off, buring refuse piles, and underground mine fires. Furthermore humans and animals who have ventured into abandoned mine openings have died from exposure, suffocating gases, and mine collapse. This paper explains the method of pneumatically filling and sealing these openings and underground works by means of employing pneumatic equipment and proper backfill material together, thus achieving high material compaction and thereby providing the complete filling of the voids and alleviation of the mentioned dangers. NEUMATIC SYSTEMS The use of air to transport material is widely used; however, conveying abrasive material (e., rock, earth, and cement) requires certain pneumatic transport systems designed to handle the abrasiveness as well as the size of these materials. The Eby pneumatic transport sys tem, known as a Mobile Stower, in mounted on a 42-foot trailer pulled by a Kenwor th tractor. This arrangement allows for quick mobilization and project set-up. The pneumatic system, composed of several components assembled together, produces the volume and pressure of air required to transport the material. Knowledge of elevation, ambient temperature, and material composition at the locations to be backfilled play a big part in the design and useage of the pneumatic system. In this particular system design, material is placed by a front-end loader into an eight (8)-yard hopper which is located over a belt conveyor. The conveyor transports the material up to an air lock feeder, which is the metering devise used to feed the material into the Tee Injector located directly below. Air is supplied by a positive displacement blower which, in this instance, delivers up to 4400 CFM's of air at 8 to 12 PSI. Horse power requirements to drive the blower are met with the useage of either a diesel engine or an electric motor. A diesel engine enables the Mobile Stower to operate in remote areas. As the air flows through the upstream air piping, it passes through the Tee Injector and picks up the material and conveys it through the material conveyance pipe, (referred to as down-stream pipe), and out the placement nozzle. Depending upon material composition and the amount of tonnage to be moved, either mild carbon steel pipe or specially heat- treated hardened pipe is used for the material conveyance line. The entire pneumatic system is controlled from the operator's console. With the aid of instrumentation, only one person is required to operate the system. Tonnage rates vary in accordance with horse power and air supply, as well as

Jan 1, 1982