Search Documents

By B. k. Kenzhaliyev, M. A. Naimanbayev, Zh. A. Baltabekova, N. G. Lokhova

In research various desorbents were used to desorb the following rare-earth metals from Purosorb 140 cation exchanger, i.e. ammonium chloride; ammonium sulfate; a mixture of nitric acid and ammonium nitrate; a mixture of hydrochloric acid and ammonium chloride; a mixture of sulfuric acid and ammonium sulfate. It was established that a solution containing 30 g/dm3 of H2SO4 + 300 g/dm3 of (NH4) 2SO4 is the most optimal desorbing solution to desorb REMs from macroporous Purosorb 140 cation exchanger impregnated with rare-earth metals from industrial dihydrate wet-process phosphoric acid. It was established that the residual REM content in the cation exchanger decreased from 0.89 to 0.10 wt. % with an increase in the ammonium sulfate concentration from 10 to 400 g/dm3. Technological desorption regimes for rare-earth metals from cation exchanger were developed. The optimal conditions were determined to desorb rare-earth metals from the Purosorb 140 cation exchanger, particularly temperature 25°C; L:S ratio = (0.8 ÷ 1.1):1; duration = 1.0-1.5 hours. Keywords: Rare elements, sorption, cation exchangers, wet-process phosphoric acid, desorption

Jan 1, 2020

By Christopher Mark

Coal bursts are typically associated with highly stressed coal. Most bursts occur during retreat mining (longwall mining or pillar recovery) in highly stressed locations like the tailgate corner of the longwall panel. Others are associated with multiple seam interactions. However, a small but significant percentage of coal bursts have occurred during development or in outby locations unaffected by active mining. Most development bursts have been relatively small, but some have been highly destructive. No theory of coal bursts can be complete if it does not account for this type of event. This paper focusses on the development mining coal burst experience in the US, putting it into the context of the entire US coal burst database. The first documented development coal burst occurred almost exactly 100 years ago during slope drivage at the Sunnyside Mine in Utah. Sunnyside subsequently had a long history of bursts, mainly during retreat mining but also during development. Several Colorado mines have also experienced multiple development bursts. Some, but by no means all, of the development bursts in these western US coalfields have been associated with faults. In the Central Appalachian coalfields, most development bursts have occurred in multiple seam situations. In some of these cases, however, there was no retreat mining in either seam. The paper closes with some lessons from this history, with implications for preventing such events in the future.

Jan 1, 2017

By Gus Van Weert

The cost of oxygen is a major and common factor in the hydrometallurgical processes developed or proposed tor the oxidation of refractory pyrites. This cost involves charges for the generation and the transfer of the 02 to the mineral slurry. Bio-oxidation faces considerable design demands which require large scale equipment to be resolved. Nitric acid assisted oxidation offers low cost oxygen units; this method of pyrite oxidation deserves a closer look for large scale plants treating pyritic gold ores and concentrates.

Jan 1, 1990

By E. J. Onuscheck

With passage of the Federal coal' Mine Health and Safety Act of 1969, many challenges have been directed to the industry's mining and safety engineers. The most critical challenge is that of ventilation. The language concerning ventilation in many sections of the Act could very well deprive or limit the mining engineer in planning the ventilation for new mines, since the Act requires federal approval of all ventilation plans. Dependent upon approval and of course application of the law, this could, due to economics, prohibit the opening of new mines in some cases. Petitions for modification of some mandatory standards relating to ventilation have already been filed under Section 301(c). It is quite possible that many of these standards may be modified.

Jan 1, 1970

By E. L. Garton

The Bureau of Mines for a number of years has been conducting an investigation of crude petroleum from producing fields in the United States and the Western Hemisphere and has published a series of reports on these fields. Analyses of crude-oil samples from many oil fields of Oklahoma are given in Bulletin 2913. Analyses of 21 representative crude oils from various producing zones of the Oklahoma City field are given in this report. A close study of the analyses reveals very few differences in the general characteristics and chemical properties of these oils.

Jan 1, 1932

By Yerkezhan Madenova, Kairat Kalmurzayev

This study intends to demonstrate the engineering application of ground penetrating radar (GPR) that would enable site engineers to prevent the high cost of blind drilling. At the tailing dump located in Zhairem Mining and Processing Plant, the challenge of sheet pile driving is encountered due to the indefinite watertight clay layer deposition depth that serves as a protective layer against groundwater contamination. A numerical model of the soil underlying the tailing dump is built using the existing hole data to compare and confirm the existing geological cross sections for three profile lines along the south and southeast parts of the tailing dump. GPR is employed to investigate the subsoil geological structure and detect the watertight clay layer deposition. On the basis of radargrams tied to the existing borehole data in the numerical model, 21 drill hole locations are suggested to assess and confirm the clay layer depth along profile lines at the tailing dump. The drilling results of the suggested holes confirmed the expected depth of the clay layer. It is concluded that GPR is a practical and economic subsurface mapping method that can prevent the high cost of blind digging of the ground and orient the drilling operations effectively.

Jan 12, 2023

By R. J. Colony

The failure, or disintegration, of concrete in structures, even when the cement, sand, and coarse aggregate used have passed satisfactorily all tests and inspections, is not uncommon. Such failures occur even when proper methods of mixing and placing have been used and where weather conditions were correct. In these cases, the origin of the trouble must be sought in the cement; therefore some additional mode of determining the quality of cement must be employed. The problem is to find a simple, usable, easily applied method that will supplement the standard tests. The solution of this problem involves a knowledge of the chemical composition of Portland cements, also of their constitution (or componental composition), as the behavior of a cement, when gaged, is dependent on the physical and chemical characters of the compounds of which it is composed, the proportions existing between them, and the fineness of grinding. It is likewise essential to know the character, behavior, and composition of the hydration products of Portland cement. The most promising method of attack makes use of chemical, mechanical, and petrographic methods. Chemical, by determining quantitatively not only the usual constituents, but the carbon dioxide and water. Mechanical, by determining the fineness with the air analyzer,' which separates into fractions of various grain dimensions all of that portion which in the ordinary sieve test passes the 200-mesh sieve and constitutes at least 75 per cent. of the total cement. These fractions may be further studied chemically and petrographically and micrometric measurements can be made of the grains. Petrographic, by the method of immersion, and by making thin sections from test pats of both neat cements and standard mortars. Normal Portland cement is composed of mechanical mixtures of definite chemical compounds having constant chemical and physical properties. In the order of their cementing qualities these are: Tri-

Jan 1, 1922

By D L. Kennedy

It has always been a challenge to accelerate the underground development progress by increasing the advance rate of each development round. Surveys have shown that most of the development rounds have only been pulled 84 per cent to 94 per cent of the drilled length. Where bare detonators have been used as primers, less advance rate is expected. In order to obtain a good understanding of the influence of priming upon the advance rate in underground development, a series of high energy primer trials has been conducted by Orica Explosives in the goldfields using various types of Orica high energy Anzomex « primers. It has been shown that development face has been pulled an extra 140 mm to 420 mm by priming with Anzomex « K primers compared with conventional primers. From all the trials at different sites, we have seen that the face pulled using K primers was more square than that pulled using conventional primers. Virtually, no butts and toe were left on the face developed using K primers. Computer simulation has been conducted using either a conventional primer, a bare detonator or a K primer as initiator. The study compared the predicted crack patterns developed around the toe of the hole and it was deducted that a detonator-initiated hole would leave a butt some 200 mm longer than that from a conventional primer-initiated hole, and a K primer-initiated blasthole would give rise to stronger initial p-wave, promoting crack development around the toe and increasing the ability to pull close to the full depth.

Jan 1, 1999

By G. K. Manning, A. R. Elsea, C. R. Simcoe

Boron increases the hardenability of hypoeutectoid steels by decreasing the nucleation rate of ferrite and bainite. It is postulated that concentrations of lattice imperfections, such as exist at the grain boundaries, furnish the necessary energy for nucleus formation. Boron, because of its atomic diameter, will concentrate at lattice imperfections where sites of suitable size are present. Boron will decrease the energy of these local areas by occupying these sites. This mechanism accounts for the large increase in hardenability observed with small amounts of boron. The loss of the boron hardenability effect and the boron precipitate formation are explained on the basis of increased concentration of boron at the grain boundaries either with increasing boron content of the material or with increasing temperature. COMMON alloying elements affect both the nucleation and growth rates of the austenite decomposition reactions.' This effect is largely a result of the slow diffusion rates of these elements. Although a small addition of boron markedly increases the hardenability of steel, the diffusion rate of boron, which is of the same order of magnitude as that of carbon, can hardly account for this effect. An addition of boron in the range of 0.001 to 0.003 pct is about as effective as an addition of 0.30 pct Mo, 0.40 pct Cr, or 1.25 pct Ni in increasing the hardenability of a 0.40 pct C steel;' however, increasing the carbon content of the steel decreases the effectiveness of the boron addition."' The difficulty in understanding why so small an addition of boron can replace much larger quantities of the more strategic alloys, together with the erratic behavior sometimes encountered in boron-treated steels, has interfered with their general acceptance by industry. In the belief that an understanding of the mechanism by which boron increases the hardenability of steel should lead to a more general acceptance of boron-treated steels, a research investigation to determine this mechanism was undertaken at Battelle Memorial Institute under sponsorship of Wright Air Development Center. Experimental Work In order to study the effect of boron on the transformation of austenite to ferrite and bainite, a group of steels was made with a basic composition similar to that of the SAE 8600 series. This base composition was chosen because it has sufficient hardenability to permit accurate measurement of the times required for transformation to start at various temperatures. The chemical analyses of the steels used in the first part of this investigation are listed in Table I. These steels were made as 200 lb heats in an induction furnace. The furnace charge was Armco ingot iron with the alloying elements added as ferroalloys. After the alloy additions were made, the heat was deoxidized with 0.125 pct Al. A 100 lb ingot was cast and an addition of 0.003 pct B, as ferroboron, was made to the metal remaining in the furnace. This metal was cast into a second 100 lb ingot. The ingots were forged to 11/4 in. diam bar stock from which end-quench hardenability specimens were obtained. Part of this material was further reduced by hot rolling to lx¼ in. bar stock from which specimens were obtained for isothermal transformation studies. Studies of Nucleation and Growth: End-quench hardenability tests were performed on these steels, using an austenitizing temperature of 1600°F. The hardenability curves, shown in Fig. 1, indicate that boron treatment resulted in considerable increase in hardenability of the steels. Any such change in hardenability must result from a change in the transformation rate of the austenite, and these rate changes can be established readily by isothermal transformation studies. Isothermal transformation studies were conducted on these steels as follows: specimens were austeni-tized at 1600°F for 15 min, transferred to a lead bath operating at a constant subcritical or intercritical temperature, held for various lengths of time, and water quenched. The specimens were sectioned for metallographic examination to determine the amount and the type of transformation products present. In order to determine the effect of boron on the formation rate of ferrite, isothermal transformation tests were made on the 0.20 pct C steel in both the boron-treated and boron-free condition at an intercritical temperature of 1375°F where ferrite is the only decomposition product of this low carbon austenite. The results of these tests are shown in Fig. 2, where the percentage of ferrite formed is plotted as a function of time at temperature. It is apparent that boron markedly decreased the transformation rate of austenite to ferrite at this temperature.

Jan 1, 1956

By Achilles J. B. Dutra, Carlos M. Juarez

"The use of thiourea as a gold leaching reagent has been extensively studied by many researchers, and it has proved to be promising for some cases as refractory ores. Otherwise, the recovery of gold from these solutions did not receive so much attention. In this paper the electrowinning of gold in acidic thiourea solutions was studied by voltarnmetry and chronopotentiometry. An adsorption step was detected prior to Au(I) reduction and the diffusion coefficients at 25°C for Au-TU complex and FD were found to be 1.00 x 10.5 cm2 S-I and 1.98 x 10-5 cm2 S-I respectively. At -0.350 V (SCE) a passivation probably due to TU adsorption was observed. For higher overpotentials hydrogen evolution was the main reaction.IntroductionThe use of acidic thiourea solutions for the extraction of gold and silver has shown to be a promising alternative to the traditional process of cyanidation, specially for certain refractory ores (1-3) and electronic scrap (4). In some cases, the industrial scale was reached (1,5). The thiourea leaching of precious metals presents advantages over cyanidation, as faster kinetics, lower toxicity and lower sensibility to base metals; however the costs due to high thiourea consumption impairs its use.The majority of the publications on thiourea processing of gold is on leaching. Many are review papers (5-7). Recently, the adsorption and desorption of the gold-thiourea complex on activated carbon and ion exchange resins have been studied (8-11).Little research has been done on the electrowinning of gold from acidic thiourea solutions, most of it has been carried on the seventies and beginning of the eighties in the former USSR (12-17) and concerned the eletrolytic extraction of gold in tridimensional cathode cells.The present paper concerns the cathodic behavior of the gold-thiourea complex in the presence of formamidine disulfide in order to provide information on the electrowinning of gold from solutions obtained directly from leaching or from an elution process."

Jan 1, 1997

By Liane L. M. Kadnuck

This report summarizes the results of a hydrologic research study conducted by the U.S. Bureau of Mines (USBM) in cooperation with Energy West Mining Co. at the Deer Creek and Cottonwood Mines, near Orangeville, UT. The USBM evaluated hydrologic and overburden failure data to assess the response of local ground water to underground coal mining in single-and multiple-seam conditions. Fourteen springs located over the two mines were investigated in the study along with overburden failure response caused by longwall panel extraction. Spring discharge was compared to climatic variation and time of undermining to quantify response to undermining. Spring discharge had been reduced owing to below-normal precipitation during the period evaluated. The response of springs to mining in the vicinity was influenced in part by the thick overburden present at the study site the presence of hydrophilic clays and mudstones in the overburden stratigraphy, and elevation of the springs above mine level, which buffered the effects of undermining.

Jan 1, 1994

By W. E. Showalter

This paper discusses some of the results of combstion-drive tests which were made in a test cell using a sand bed 10 in. in diameter x 10-ft long. The test method is illustrated and described. The relationship between the API gravity of the in situ oil and the amount of air required for combustion drive is discussed in detail. Other things constant, the air requirement for combustion drive increases as the APl gravity of the in situ oil decreases. If the test results apply to actual reservoirs, the lowest-priced oils may cost the most to recover by this method. Information is shown which indicates that the effect of pressure on the amount of hydrocarbon burned is not large. A method of predicting air requirements from the API gravity of the in situ oil is presented. INTRODUCTION Combustion drive is the term used to identify the process of interstitial or in situ burning as an oil recovery method. Part of the in situ oil is burned to generate the energy needed to produce the remainder of the oil. Combustion drive as an oil recovery mechanism remains an economic uncertainty in spite of all the work that has been done by the industry in both laboratory and field?-6 This paper will show some of the results of tests which were made in a test cell for the purpose of studying the nature of the combustion-drive process. It will present data which indicate that the API gravity of the in situ oil is a significant indicator of the amount of air required to drive a burning front through oil sand. Air requirement varies inversely as the API gravity of the in situ oil. EXPERIMENTAL The tests were performed in a cell which utilized a cylindrical sand section 10 in. in diameter x 10-ft long. The thin-walled metal pipe which held the sand was wound with twenty external electrical resistance heaters which, by means of an automatic controller, maintained adjacent sections of the wall of the pipe at temperatures equal to the temperatures of the contained sand. Each heater covered 6 linear in. of the pipe. By this means lateral heat loss from the sand section was minimized, thereby causing the sand section to simulate more closely a horizontal increment of a combustion-drive reservoir. Fig. 1 shows a schematic diagram of the test assembly. Thermocouples to measure the temperature in the sand were located every 6 in. along the length of the sand section. The pipe containing the sand was enclosed in a cell designed for an operating pressure of 500 psig. The inlet air pressure was controlled at the inlet, and the gas flow rate was controlled and measured at the outlet of the cell. The oil sand used for the tests was prepared by mixing first water and then oil with the noncon-solidated sand using a closed mixer similar to a cement mixer. Table 1 shows a screen analysis of the sand. Ninety percent of the sand was 100 mesh or finer. This sand was a mixture of 80 per cent No. 120 Nevada White Sand and 20 per cent Tennessee Hi-Fusion Moulding Sand No. 3. The Nevada sand was a clean silica sand. The Tennessee sand con-

By R. H. Swallow, George Hess

The purpose of presenting this paper is to show: 1. The applications of aerial photography to the map requirements of strip mining. 2. The methods and procedures for producing accurate aerial contour maps. 3. The advantages of aerial contour mapping over stadia or plane table methods. Introduction Aerial photography was once a crude, uncertain tool. 'Today it is a precision mapping instrument which saves important time and money for strip mining and other industry. Aerial photography began in the boxkite days of aviation. The Army first used it for rough reconnaissance photographs. Then, in the early Twenties, industry began to use aerial photographs of their plants and facilities for advertising or annual reports. The quality of these pictures was not very good by today's standards, but this work began the development of better cameras, better lenses, better photographic techniques. Then, some farsighted engineers and aerial photographers found that if the camera's axis were vertical to the earth's surface, these pictures could be the source of valuable mapping information. By viewing these pictures in stereoscopic pairs, accurate measurements could be made and contour maps produced from this aerial photographic base. So the aerial mapping business developed, using the plane and aerial camera to collect the data, working with skilled ground parties who established a network of ground control for this map information photographed from the air. Over the following years, a whole new science developed, known as photogrammetry. Precision cameras and lenses were perfected, and the narrow view of the surveyor's transit was broadened to the vast perspective of the mapping plane. Stereoscopic Coverage Obtained Today in making aerial topographic maps, aerial photographs are exposed so that full stereoscopic coverage for the survey area is secured. To obtain true elevations these photographs are processed through a series of precision measuring and contouring instruments which employ a principle similar to the military range finder. Here is how aerial mapping is being used by your industry. Topographic maps are but one of three products from aerial photographic surveys. First, there are the individual photographs. These are taken in flight strips, exposed with an overlap, just as shingle on a roof overlap. Exposures are overlapped from 55 to 60 pct along the line of flight so that a large part of the area in one picture also appears on the adjacent photograph. Successive strips are flown with a side-lap of between 20 and 25 pct. Each point on the ground thus will be somewhere near the center of at least one photograph in the series. They may be studied under a stereoscope and relief seen in a third dimensional effect. Geologic features that may go unobserved in ground exploration are often detected under stereoscopic inspection. Moreover, though field checking is not obviated with these aerial photographs, it is directed toward critical areas and toward worthwhile anomalies. Aerial Photographic Mosaics The second product of an aerial survey is the photographic mosaic. This is an assembly of carefully matched aerial photographs in mosaic form. Although not as accurate as the topographic map, it does reveal a wealth of cultural detail in true relative scale. Since the mapping plane is flown over the area at a fixed altitude, the peaks and valleys are pictured at different scales. During compilation these scale differences are compensated by adjusting one vertical picture to another according to plotted ground control positions. Only extreme variations in ground elevation cannot be

Jan 1, 1950

By B. H. Kear, B. J. Piearcey

The orientation and temperature dependence of the tensile and creep propevties oj Mav-M200 crystals halle been determined. Crystals oriented for single slip exhibit ,maximum ductility, minimum work hardening, and least creep resistance, whereas crystals in multiple slip orientations show nzinimu~n ductility, strongest work hardening, and greatest creep resistance. At 1400" and 1600°F there is a marked improzlenzent in creep strength for orientations approaching [001] and [111], indicating that interactions between dislocations gliding in intersecting octahedral slip systems play an important role in creep resistance. At 1800°F the creep strength is much less dependent on orientation, which is rationalized in terms of slip in cube planes as well as octahedral A frequent mode of failure in high-strength cast nickel-base superalloys is by intergranular fracture, particularly along those grain boundaries oriented transverse to the major stress axis. VerSnyder and ~uard' demonstrated that this problem could be overcome by eliminating transverse grain boundaries through unidirectional solidification. Piearcey and versnyder2 made use of this principle in the development of unidirectionally solidified gas turbine blades and vanes, where the growth direction of the columnar grain structure coincides with the axis of principal stress under operating conditions. The present investigation was undertaken to determine if further improvement in properties may be obtained by eliminating grain boundaries altogether, so as to take advantage of the well-known dependence of mechanical properties of single crystals upon the orientation. 1) EXPERIMENTAL PROCEDURE Single crystals of Mar-M200* were grown from the melt under vacuum by a modified Bridgman method. The melt was poured into a preheated alumina mold, and crystal growth was promoted from one end by appropriate gradient cooling. Tensile and creep specimens (2 in. diam by $ in. gage length) were prepared by a series of operations involving electrical discharge machining, precision grinding, and electropolishing. The orientations of the specimens were determined by the Laue X-ray back-reflection method. Tensile tests were carried out in aWiedemann machine with furnace attachment, using a strain rate planes. In all orientations imzpvouement in the strength charactevistics of the material can be induced by heat treatment. Creep ad stress rupture data for (001) oriented crystals are compared with similar data obtailted previously joy random polycvystalline material, and also columnar grained material having a prejevved (001) orientation. The single-crystal )material exhibits both longer rupture life and lower minimum creep rate at all temperatuves, and the rupture elongation is comparable with that in the columnar grained material. From these results it is concluded that single crystals should and useful application in gas-turbine blades and tanes. The optimum orientation for a blade is considered to be with its axis of principal stvess parallel to (001) ou (111). of 0.0001 sec-'. Load and extension were recorded directly on an X-Y recorder. The strain measuring device consisted of extension arms attached to the grips at one end and leading out of the furnace to an LVDT (linear variable differential transformer) at the other. Creep tests were performed using a standard constant load creep frame. 2) DISCUSSION OF RESULTS 2.1) Structure of Alloy. The structure and segregation in as-cast and heat-treated Mar-M200 has been described in detail else where.~ The main features are as follows: the as-cast material is heavily cored, due to pronounced dendritic segregation during solidification; the dendrites are rich in tungsten and cobalt whereas the interdendritic regions are rich in chromium, titanium, nickel, and carbon. The structure consists of -60 vol pct coherent precipitate of y', basically Ni3(A1,Ti), in a matrix of y (nickel-base solid solution), interspersed in the interdendritic regions with minor MC carbides and -y' eutectic. The y' particles, and y-y' eutectic, contain more titanium, aluminum, and nickel, and less tungsten, cobalt, and chromium than the y matrix. Heat treatment partially removes segregation, eliminates the eutectic, refines the y' dispersion in y, and gives additional partially coherent M23Cs carbide. An as-cast crystal, therefore, is composed primarily of two oriented phases (y + y'), whereas the normally heat-treated crystal consists of three oriented phases (y + y' + MZ3Cs). Typical electron transmission micrographs of the y + y' structure are shown in Fig. 1. Crystals grown in the (100) orientation develop a simple unidirectional dendritic structure, Fig. 2, since (100) happens to be the preferred direction of growth for dendrites in this material. Crystals grown in the {110) and (111) orientations, however, tend to promote equal growth, generally in separate colonies, in the two and three geometrically favored (100) growth directions, respectively. In other orientations of growth, a single (100) dendrite direction generally pre-

Jan 1, 1968

By Saba Mohan

This study presents results based on the Pile Installation Demonstration Project (PIDP) that was conducted as a part of the East Span San Francisco-Oakland Bay Bridge Seismic Safety Project. For the three full-scale pile installations, two different high-energy hydraulic hammers were selected for the installation. However, these hammers may not have sufficient energy to drive these large diameter piles at their ultimate capacity following long-term set-up. Nevertheless, these hammers were selected because, soil plug behavior, the generation of excess pore pressures and remolding of soil during driving were expected to reduce the shaft and end bearing resistance, and therefore reduce the energy required to drive these piles to design penetration. Data collected during continuous installation driving and after a series of re-strikes at different set-up times ranging from 1 to 33 days were used as input data for CAPWAP. These results were used to estimate the soil resistance along the pile length and at the toe of the pile, and the soil pile set-up behavior. Validity of the procedures used to predict the soil resistance to driving and predicted blow counts were verified with the field observed blow counts and the energy that was delivered to the pile. Based on combined CAPWAP analyses, the soil pile set-up with time was estimated and compared with results of other methods currently available in the literature for predicting the soil pile set-up rate.

Jan 1, 2002

By Zhang You-di

A comprehensive model has been set up for surface mine long range planning. It is a system simulation model based on the oriented graph theory. Via this model, a series of mining results such as mineral and waste volume, mineral quality, mining intensity, material haulage distances, dumping area parameters and mining coat for different mining alternatives, can be derived and optimized. This model has been applied to 37 mining alternatives in several surface coal mines and proved mathematically correct and results reliable.

Jan 1, 1986

By D Wilson, R R. Vandebeek, R A. Bowes

"As business opportunities are sought around the world, the explosives industry must oftengrapple with the United Nations Transport of Dangerous Goods Recommendations.Canadians have problems in this area that are similar to those of other countries. Thispresentation outlines, through a case study, how a container for shipping ""explosives"" wasdesigned, tested and approved for use by the Chief Inspector of Explosives, the""Competent Authority"" for Canada."

Jan 1, 1993

By W. Fourney

In the late 70’s and early 80’s in conjunction with other oil and gas well stimulation studies, personnel from the Dynamic Effects Lab performed model testing to demonstrate the effectiveness of utilizing an open section of borehole just before a plug. We called the process stem induced fracturing. The open section beneath the stem was used to increase the pressure magnitude and spread out the duration of the pressure pulse. This technique was later utilized to by Frank Chiapetta (1) in the fracture and fragmentation of rock in quarry blasting situations. He called his technique air deck blasting. In fact, Frank found that the Russians had previously discovered the same technique. There is currently interest in utilizing air deck blasting with an open section of hole beneath the explosive at the bottom of the bore hole to better remove the toe in a fragmentation shot. This paper reviews the development of stem induced fracturing and then describes a series of model tests conducted to measure borehole pressure at points along a borehole when an explosive charge is detonated at the midpoint of the borehole. Tests were conducted in both stiff boreholes (aluminum) and less rigid boreholes (PMMA-Plexiglas). Pressure time profiles were measured at the charge site, midway between the charge and the bottom of the hole, at the stemming at the top of the borehole, and at the bottom of the borehole. Crack initiation sites and crack propagation were also determined in the PMMA models. Some high speed pictures were taken of the event in the PMMA.

Jan 1, 2006

By G. J. Biefer

"Fatigue and corrosion fatigue measurements were carried out on five commercially available metals -four steels and an aluminum alloy -which are used as structural materials in mine shaft conveyances. In the corrosion fatigue measurements, drain waters collected in the shafts of three different Canadian mines were used as corrodents. The mine waters had been selected on the basis of their relatively large differences in acidity and/ or composition.It was found that the corrosion fatigue strengths of the four steels were similar, despite their differences in tensile properties, and that the type of water used in the tests had little effect on the results. Mild steel showed the highest and most consistent values of the damage ratio (ratio between the corrosion fatigue and the plain fatigue strengths at 107 cycles). The corrosion fatigue behaviour of the aluminum alloy (ASTM Type 6061-T6) was found to differ markedly in the three mine waters. A high damage ratio (i.e., superior performance) was shown in a mine water in which the corrosion attack was uniform; much lower damage ratios were shown in waters which produced localized corrosion attack. Corrosion rates were too low to be deter-mined conveniently by conventional weight-loss methods, but calculations from polarization curves provided a rapid demonstration that corrosion rates were distinctly lower in the mine water which produced high damage ratios."

Jan 1, 1967

By Ihsan Berk Tulu, Keith A. Heasley, Chris Mark

"The Analysis of Retreat l\.fining Pillar Stability (ARJ\1PS) and the Lal\.fodel programs have been used successfully in the U.S. for designing safe pillar recovery operations for many years. However, the recent Crandall Canyon l\.fine collapse showed that further research is required to improve the pillar design for recovery under deep cover. To this end, the National Institute for Occupational Safety and Health (NIOSH) and the West Virginia University (WVU) l\.fining Engineering Department have been working together to improve both the ARJ\1PS and the Lal\.fodel programs.This paper compares and analyzes the overburden loads calculated by ARJ\1PS 2002, the new ARJ\1PS 2010, and the Lal\.fodel program with regard to the retreat pillar line, the gob, and the barrier pillars. The analysis shows a number of distinct differences between the ARJ\1PS and Lal\.fodel loading distributions. Ultimately, the programs, with their distinctive load distributions, are used to analyze a database of 52 deep cover pillar retreat case studies, and the ability of each program to discriminate between successful and unsuccessful retreat pillar plans is evaluated.INTRODUCTIONThe Analysis of Retreat l\.fining Pillar Stability (ARJ\.f PS) and the Lal\.fodel programs have been used successfully in the U.S. for designing safe pillar recovery operations for many years. However, the recent Crandall Canyon l\.fine collapse showed that further research is required to improve the pillar design for recovery under deep cover.Pillar recovery accounts for less than 10% of the coal produced from underground coal mines; however, in the period between 1989 and 1996, it accounted for more than 25% of all ground fatalities (l\.fark et al., 2003). In the past 15 years, the safety of retreat mining operations has greatly improved. l\.fark (2009) explains three steps promoted by l\1SHA and NIOSH for safer pillar recovery:1) Global stability through proper pillar design2) Local stability through proper roof support3) Worker safety through proper section managementThe ARJ\1PS and Lal\.fodel (Heasley, 1998) programs have been playing an important role in guiding mine operators in designing pillars to ensure the global stability of a retreat panel."

Jan 1, 2010