Search Documents

By Helmut Thielsch

METALLOGRAPHIC specimens whose surfaces are to be investigated are too thick to allow either light or electrons to pass through them for microexamination by transmission. This difficulty is overcome with optical microscopes by illuminating the surface through the objective lens. For electron microscopes best results are obtained by preparing thin replicas of the surface of the specimen, placing them in the microscope and passing the electron beam through them. Since electron microscopes represent a rather recent invention, they have found little application as compared with optical microscopes. This is true because, aside from the cost of new equipment and development of new techniques, some of the older replica methods necessitated the destruction of the surface from which a thin transparent replica was obtained. In other processes in which the surface is preserved, either too tedious a procedure is required, unsuited to "mass-production " requirements of industrial laboratories, or replicas of insufficient contrast and sharpness are produced. In general, investigations with the electron microscope involve five steps: (I) polishing the surface of the metal specimen, (2) proper etching of the surface, (3) preparing the suitable replica from the surface, (4) examination and photography in electron microscope and (5) interpretation. PREPARATION OF METAL SURFACES Usual metallographic polishing is generally satisfactory. It is important though that the final polish be applied very care- fully, since otherwise evidence of a small amount of deformation might show up even on relatively deeply etched surfaces. A high-power microscope should be used to determine the suitability of the polish and etch. This, of course, is not different from optical examinations, but in these, if a deep etch is used, the problem is less serious. It is frequently difficult to detect with optical microscopes poor polishing aside from superficial scratches before etching. Figs. I and 2 show micrographs of "well" and "poorly" polished nickel etched by immersing the same for 20 min. in a solution containing 8 grams cupricsulphate in 40 C.C. of concentrated HCl and 40 C.C. of H20 (Marble's reagent). The sample shown in Fig. I was polished in its final stages for 5 min. on a carborundum wheel followed by 10 min. on a rouge wheel, whereas the sample shown in Fig. 2 was polished only I min. on the rouge wheel. Generally, this procedure does not guarantee that the surface of the specimen will be either undistorted or deformed. It was applied here merely to show the effects of good and poor polishing. To the experienced investigator, plastic deformation is

Jan 1, 1946

By Robert Hopler

SECTION 9.---BORING AND BLASTING.*155. Blasting is the operation of bringing down and detaching from its bed or position masses of material by means of explosives.

Jan 1, 2011

By Peter E. Price

Salt dome hosted metallic sulfide deposits are the product of a complex evolutionary system involving halokinesis, cap rock development and diagenesis, and the generation, migration, and accumulation of basinal brines and hydrocarbons. Hydrocarbons play an important role in: (1) the production of calcite cap rock which hosts some of the metallic sulfide and sulfur concentrations, and (2) the generation of the reduced sulfur available for metallic sulfide precipitation and sulfur formation. Hydrocarbons and related fluids also are involved in the transporta¬tion and remobilization of the metals. Hydrocarbon consumption, in the course of cap rock development and sulfide mineralization at Hockley dome, is estimated to have been 6.4 million barrels of oil or 114 million cubic feet of methane. Mineral textures, including cap-rock banding, sulfide bands in anhydrite, and fine sulfide mineral banding indicate both episodic fluid influx and fluid compositional differences through time. Features such as pyrite "shells" and sphalerite and marcasite hemispheres may have been localized by hydrocarbon droplets and /or bacterial colonies. Marcasite mineralization in shallow strata above and flanking Hockley dome is best developed over the western and southern parts of the dome. This pattern mimics the known distribution of sulfide mineralization, which is dominantly marcasite, in the underlying cap rock. The iron sulfide paragenetic sequence in the sediments is pyritohedral and cubic + pyrithohedral pyrite followed by marcasite which is encrusted by cubic pyrite. Sulfur isotopic averages for the three stages are +20.8, -20.2, and +6.4 per mil, respectively. These values generally coincide with cap rock sulfate (+20 per mil), cap rock hosted metallic sulfides (-20 to +4 per mil), and sulfur in hydrocarbons (+5.8 per mil). Hydrocarbon compositions indicate provincial variations in oil composition and generation history. Long Point and Boling domes, which have an intergrown sulfide-sulfate-sulfur mineral assemblage indicative of mixed reducing-oxidizing environment, contain oils that are less mature than Hockley dome which appears to be more mineralogically segregated. Sterane biomarker compositions of the oils at Hockley, Long Point and Boling domes indicate a local, dominantly terrestrial source. An oil sample from supracap sandstones on the northeast flank of Hockley dome contained over 750 ppm combined Fe, Zn, Pb, and Co, indicating that hydrocarbons are carrying or remobilizing metals. Cap rock calcite and anhydrite also exhibit provincial variations in strontium isotopic ratios. Calcite and anhydrite cap rocks from several sulfide mineralized domes in the Houston diapir province have strontium isotopic ratios that are more radiogenic than Jurassic sea water (>0.7078). A calcite sample within massive sulfides at Winnfield dome also has a high 87Sr/86Sr ratio (0.7085). Variations in strontium isotopic ratios with strontium content indicate the mixing of at least three Sr-bearing fluids in the cap rock environment, one of which may have been the metal carrier. Anhydrite residues from diapiric salt have strontium ratios up to 0.7100, considerably more radiogenic than Jurassic seawater. These high ratios indicate either that salt and anhydrite recrystallized sometime post-Jurassic in the presence of a fluid with a high 87Sr/86Sr ratio, or that they precipitated in the Jurassic from a fluid with a higher 87Sr/86Sr ratio than Jurassic seawater. Salt domes with cap rocks containing metallic sulfides have only been found in basins that have geopressured zones. Waters from geopressured zones in the vicinity of mineralized salt domes have salinities that are two or more times higher and iron and base metal concentrations that are three to one thousand times higher, than geopressured fluids from other parts of the basin.

Jan 1, 2013

By M. J. Mechling, H. J. Sloman

"INTRODUCTION The practicability of providing safer methods of underground transportation for mine workmen and officials has been given much thought in recent years by advocates of safety, health, and efficiency. Numerous fatalities and disabling injuries have resulted from falls of roof, personal contact with both electrical conductors and timbers, and improper position or conduct of passengers while they were in man-trips. Unfavorable atmospheric exposure due to high-velocity air currents and sudden changes in temperature may adversely affect the health of mine workmen if they are transported in unprotected Cars.Recent installations of protected, man-trip cars, wherein such cars have been utilized to haul men to and from their stations in the mine, have resulted in a large reduction in exposure to haulage hazards. Where special-built cars have been used the probability of injuries to men during transportation in man-trips has been decreased, and the morale of the employees has been improved. A number of man-trip cars are in service in the coal-mining regions; those described in this circular are typical examples of a few installations."

Feb 1, 1948

By D. L. Passmore, J. D. Bennett

The reliability of mine operators' reports to the Health and Safety Analysis Center of the US Department of Labor of days lost from work by injured miners is 0.267.

Jan 1, 1987

By L. R. Burdick, J. F. Barkley

"There is a general conceit in the coal trade that the moisture- and ash-free B.t.u. of coal from the same seam, and surely from the same mine,is substantially a constant; that calculation of the moisture- and ash-free B.t.u. value from the proximate analysis and B.t.u. determined in the laboratory will reveal whether a coal came from a given area or seam; and that, having this constant, the B.t.u. value of a coal sample can be calculated fairly closely upon a dry or as-received basis from the moisture and ash values of its proximate analysis.To illustrate with a simple example;"

Jun 1, 1941

By C. H. Herty

Almost every metallurgist who has given the Howe Memorial Lecture has had a personal contact with the distinguished gentleman to whose honor this hour is devoted. Unfortunately for me, such personal contacts were not possible. However, in the preparation of a thesis on the open-hearth process, one of my earliest tasks was to make a survey of the literature, and it was from Professor Howe's Metallurgy of Iron and Steel that I drew a number of references to previous work which formed the foundation for my reading. In his volume there is such a complete exposition of the then current thought on the subject of slags and on their role in the elimination of phosphorus from steel that I feel no hesitation in discussing in this Howe Lecture the subject of "Slag Control." In the present era of close specification, the drive for uniformity of product, and the close inspection of the product and of the cost sheet, the utmost efforts must be made to control the steelmaking variables to the best advantage of the steel producer. One of the major variables is the slag in the furnace and its effect upon the composition and quality of the metal. What advantages are to be gained from slag control? In the broad sense the advantages must be tremendous, because the very foundations of good steel melting are based on "shaping up" the slag to a point where, with proper temperature, the heat is ready for the final additions. Every melter works toward these ends through his experience with innumerable heats of steel. The elimination of undesirable constituents such as phosphorus and sulphur is entirely a matter of slag composition and physical nature, a point well known for over half a century. The role played by the slag in assisting in proper heat transfer from roof and flame to the steel has been equally well known. In more recent years there has come the problem of oxygen control in the more accurate gauging of additions for making high-grade rimmed steel for the new strip mills, and in the deoxidizing additions for grain-size control and cleanliness of forging steels, both carbon and alloy. In this problem the oxidizing characteristics of the slag are of prime importance.

Jan 1, 1940

By C. H. Herty

Almost every metallurgist who has given the Howe Memorial Lecture has had a personal contact with the distinguished gentleman to whose honor this hour is devoted. Unfortunately for me, such personal contacts were not possible. However, in the preparation of a thesis on the open-hearth process, one of my earliest tasks was to make a survey of the literature, and it was from Professor Howe's Metallurgy of Iron and Steel that I drew a number of references to previous work which formed the foundation for my reading. In his volume there is such a complete exposition of the then current thought on the subject of slags and on their role in the elimination of phosphorus from steel that I feel no hesitation in discussing in this Howe Lecture the subject of "Slag Control." In the present era of close specification, the drive for uniformity of product, and the close inspection of the product and of the cost sheet, the utmost efforts must be made to control the steelmaking variables to the best advantage of the steel producer. One of the major variables is the slag in the furnace and its effect upon the composition and quality of the metal. What advantages are to be gained from slag control? In the broad sense the advantages must be tremendous, because the very foundations of good steel melting are based on "shaping up" the slag to a point where, with proper temperature, the heat is ready for the final additions. Every melter works toward these ends through his experience with innumerable heats of steel. The elimination of undesirable constituents such as phosphorus and sulphur is entirely a matter of slag composition and physical nature, a point well known for over half a century. The role played by the slag in assisting in proper heat transfer from roof and flame to the steel has been equally well known. In more recent years there has come the problem of oxygen control in the more accurate gauging of additions for making high-grade rimmed steel for the new strip mills, and in the deoxidizing additions for grain-size control and cleanliness of forging steels, both carbon and alloy. In this problem the oxidizing characteristics of the slag are of prime importance.

Jan 1, 1940

By William M. Greenslade

As the search for minerals leads to deeper mines the need to control water inflow into mine shafts and mine workings will grow. As shal¬lower more readily available minerals are exploited, ore bodies which were previously uneconomic be cause of their depth will now become attractive targets. In known mining districts new ore bodies are being discovered down dip of existing ones. In the west many metal deposits are being developed in rocks of the mountain front pediments, frequently covered by several hundred feet of saturated alluvium. Greater depth often means that workings are developed well below existing water tables, creating high hydrostatic heads adjacent to mine workings. The purpose of this paper is to review some of the methods available for determining if water control will be necessary and to present some of the techniques for locating water bearing zones and the amount of water to be expected. The paper will concentrate on problems associated with water control in mine shaft development, although many of the exploratory techniques are similar to those needed for assessing overall mine water inflow problems. A brief case history on water control problems in mine shafts in the Grants mineral belt of northwestern New Mexico is presented. Water control during shaft sinking presents some unique features. First, the problem is a relatively short term one, since water control is often necessary only while the shaft is being sunk. Control measures may be necessary only while the shaft is open into the water bearing zone and the lining installed and cemented. Secondly, limited working space within the shaft area presents difficulties in handling large amounts of water inflow. The presence of water in the shaft working area increases sinking time and the potential hazard to miners. Finally, there is the economics of shaft sinking. While the shaft is being sunk no ore is being produced and there is every incentive to minimize costs.

Jan 1, 1979

By R. Kamguem

The surface of a mechanical part plays an important role in determining performance in service. The presence of scratches left by the cutting or tearing of the material on the surface of the workpiece supports the concentration of stress and strain. This article presents the experimental study for high speed milling of the aluminum alloy 7075-T6, using cutting tools different by the nose radius and coatings (TiCN, TiAIN, TiCN + A12O3 + TiN). A multi levels factorial design of experiment (DOE) and statistical analysis was used. The roughness parameters investigated are Ra, Ra, Rv, Rc, Rsm, and Rk. The results show that the feed rate, the types of coatings and the geometry of the cutting tools have the most significant impact on the surface roughness profil. Surface finish charts according to feeds and cutting speeds were established for each tool tested.

Jan 1, 2011

By P. A. Bahri, D. G. Dixon, T. M. Woodward

A comprehensive mathematical model of the Sherritt-Gordon ammoniacal pressure leaching process at K winana Nickel Refinery has been constructed. The process is comprised of six autoclaves functioning as a three-stage leach circuit, operating over the temperature and pressure ranges of 85-95°C and 750-1000 kPa, respectively. The process chemistry forms a complex series-parallel reaction network, characterised by: (1) the gas-liquid mass transfer and reduction of oxygen, (2) the oxidation of eight distinct minerals, (3) the oxidation of sulphur, and successive reactions involving various intermediately oxidised sulphur species, and (4) the oxidation of Fe(II) to Fe(III), and subsequent precipitation as a hydrated ferric oxide. Material balances were developed for species in all three phases, and an energy balance to account for all reactions and phase conversions. The multiple convolution integral (MCI) statistical reactor model was employed for the scale-up of particle kinetics. The model has been validated against plant data, and simulation results are in agreement with plant performance.

Jan 1, 2005

By F. T. Paleari

Radial gas holdup profiles have been measured in a 50x400 cm flotation column using a multi-cell conductivity probe. Three different bubble generation systems were examined: up to eight vertical filter cloth spargers, three horizontal filter cloth spargers, and three (horizontal) Cominco-type spargers. The variables tested were: number of spargers, symmetry of their arrangement, and height above spargers. Batch water with up to 20ppm frother concentration was used. The general observation is that the profiles tend to be uniform (i.e. flat) with some exhibiting a slight wavy shape. The vertical sparger arrangement proved the most difficult to achieve profile symmetry. The horizontal spargers gave uniform profiles at right angle to their length but a decreasing gas holdup along their length; the Cominco-type spargers gave slightly less scatter in the data. Switching off selected spargers (to simulate malfunction) did not produce strong asymmetry in the profiles.

Jan 1, 1993

By R. D. Cromarty, J. Du Toit

"Penetration of matte into tap-hole bricks causes detrimental refractory wear, which can lead to furnace breakouts. The ability of the tap-hole clay to form a protective layer on the brick, thereby limiting matte penetration was investigated by examining the interaction between platinum group metal (PGM) matte, tap-hole clay, and alumina-chrome refractory bricks on a laboratory scale.Samples containing clay and brick as well as samples containing clay, brick, and matte were heated to different temperatures to establish the clay-brick interaction and the extent of matte penetration. The greatest degree of physical contact between the brick and clay was achieved at curing temperatures of 600°C. Poor clay-brick contact was observed in the sample that was heated to 900°C.Matte displaced the clay in the clay-brick-matte sample that was heated to 1350°C, with significant matte penetration into the brick. Less matte penetration was observed when the clay-brick-matte sample was heated to 1500°C. Less matte penetration was also observed in the claybrick- matte sample in which the clay and brick were pre-baked at 800°C, and the sample then reacted with matte at 1350°C. IntroductionFloatation concentrate from ore from the eastern Bushveld Complex of South Africa, specifically the Platreef, Merensky, and UG2 reefs, forms the feed to the Polokwane platinum smelter (Hundermark, De Villiers, and Ndlovu, 2006). The ore from the UG2 Reef has a high chromite content, which requires high operating temperatures (1500–1700°C) to avoid chromium spinel build-up in the furnace hearth. These high operating temperatures lead to matte superheats in the vicinity of 500– 600°C, which put increased demands on the refractory materials (Nelson et al., 2005).Upon tapping, the matte moves through the tap-hole, which consists of an aluminachrome refractory brick-lined tapping channel (Hundermark, De Villiers, and Ndlovu, 2006). The flow of molten matte is stopped by the injection of tap-hole clay to form a plug in the tap-hole. The tap-hole clay hardens and strengthens during curing to obtain the required hardness and refractoriness against penetration, corrosion and erosion (Nelson and Hundermark, 2014)."

Jan 1, 2016

By Nan Wang

Based on the commercial computational fluid dynamics software, Fluent, the fluid flow and temperature field in an iron-bath reactor were simulated numerically, and the effects of top-blown and side-blown operating parameters on the mixing time of iron bath, distribution range of oxygen in top space, and post-combustion ratio were investigated. The simulated results showed that the mixing time of iron bath increased initially and then decreased with the increase of inclined degree and immersion depth of side-blown lance. The distribution range of oxygen became wider as pulling the top lance away from the iron bath. Furthermore, post-combustion ratio was reduced given the top lance was too close the bath. The simulation results provide theoretical base for the process optimization of iron-bath reactor and further development of new type iron-bath smelting reduction process.

Jan 1, 2009

By L van Latum, A Koh, I Thomas

Haul truck drivers are at a high risk of developing fatigue due to the monotonous nature of the work and demanding shift rosters. In the mining industry, fatigue is identified as a major contributing factor in several fatal accidents a year. A number of fatigue detection devices are now available, that can contribute to improved fatigue risk management in the mining industry. This paper describes the technology and algorithms behind one particular product which is both predictive and un-obtrusive to the operator. The Advisory System for Tired Drivers (ASTiD), was developed by Fatigue Management International (FMI) in collaboration with the Loughborough Sleep Research Centre (LSRC), both in the United Kingdom. While this system includes a model of the human circadian rhythm as a bias for predicting expected fatigue risk by time of day, it also uses yaw data generated by a solid-state gyroscope in the horizontal plane. Algorithms analyse this data to determine the level of monotony of actual driving conditions and to detect changes in steering control caused by driver fatigue. During normal levels of attention, a haul truck driver applies continuous, small adjustments to the steering wheel. As the level of fatigue increases, steering adjustments become less frequent and more erratic. Differentiating between these modes of control in the highly variable mining environment is accomplished by chromatic processing of the gyroscope data. This paper will go into some detail explaining the principles behind chromatic processing and the specific application of these in detecting fatigue in haul truck operators.Technology in itself is not the solution to addressing operator fatigue, but it plays an important role in ongoing monitoring and maintaining awareness with mining personnel. Furthermore, the specific principles behind ASTiD technology support a risk-based approach to fatigue management, allowing optimisation of the mining operation for productivity as well as safety.

Sep 26, 2011

By E. Heaton Hemingway

DURING the past year, the Watertown Arsenal has been interested in the occluded gas and oxide content of certain ordnance steels in order to determine, if possible, whether some of the peculiar failures in their physical properties might not be traced to these causes. For the purpose of best accomplishing a study of this nature, it was decided to heat the various samples of steel in a vacuum for definite periods of time at high temperatures and carefully examine the quantity and composition of the gases evolved. By the use of a fused quartz tube fitted with a water-cooled, ground-glass stopper, it was possible to maintain a vacuum at a temperature of 1000° C. for 10 hr. without perceptible leakage being evidenced as measured by a McLeod gage. The silica tube was connected with an evacuating system so constructed that the volatilized gases could be removed from time to time and a low vacuum of 0.002 to 0.0010 mm. of mercury continuously maintained. At no time during the period of heating or in the removal of the gases did the evacuated system come in contact with rubber stoppers or any rubber connections, making contamination from such a source impossible. In other words, the only volatile products that could be obtained must necessarily have come from the steel itself or from the glass and fused quartz system or from the mercury used as a sealing agent. In the earlier experiments, the steel treated was in the form of turnings, but this practice was discarded because the weights of the turnings before and after being heated were widely inconsistent, even when taken from the same piece of steel. This discrepancy developed largely through variation in the amount of metal volatilized with the gases; this metal could always be seen in the form of a ring where it condensed in the cooler portion of the tube either in the amorphous or crystalline condition. Because of the frequency in occurrence and the variation in the manner of deposition, this material was roughly analyzed and found to consist for the most part of iron. At the same time two samples of steel that had been

Jan 8, 1920

E. E. Russell Tratman, New York City (communication to the Secretary): Mr. Glenn's paper brings up again the question of the part played by coal-dust in colliery-explosions. In the discussion of Sir Frederick Abel's paper on " Accidents in Mines," read before the Institution of Civil Engineers,? much was said about the dangerous properties of coal-dust, and several instances were given of the successful use of a spray of water, water and compressed air, or exhaust-steam from an engine, to keep the mine SUEciently damp to prevent the formation of dust clouds. Methods of preventing shots from blowing out; of using water cartridges to prevent flame ; and of using lime cartridges, wedges and other means of breaking down the coal were also discussed. Mr. Emerson Bainbridge referred to the explosive termed " roburite " (ammonium nitrate and

Jan 1, 1895

By William Gleason

"There are few people more qualified to speak of the tumultuous times in the global mining industry during the past four years than Newmont Mining Corp. president and chief executive officer Gary Goldberg.Goldberg stepped into his current position in 2012, just before MINExpo 2012. Gold prices had hit record highs not long before that ($54.15/g or $1,856.40/oz on Sept. 8, 2011), expansions were happening around the world and the gold mining sector was still living in the glow of one of its longest upswings in history.That all changed between April 8 and April 15, 2013 when the price of gold dropped by nearly $200/oz ($46.27/g or $1,586.20/oz on April 8 to $40.45/g or $1,386.80/oz on April 15), putting an end to the decade-long mining boom and forcing mining companies like Newmont to re-evaluateeverything.Three years later, with the gold sector recovering, Newmont Mining is not only surviving but is thriving with a pair of mines coming online, Long Canyon in Nevada and Merian in Suriname. On Oct. 1, the Merian Mine went into production on time and more than $150 million under the initial development capital budget.Goldberg, who was one of the featured speakers at the opening session of MINExpo International 2016 on Sept. 26, also spoke with Mining Engineering about the previous four years and the future of the industry.“Mining goes through cycles all the time and gold is no different,” Goldberg told Mining Engineering when asked about surviving the downturn since 2012. “I thought it was important that we take a good methodical and steady approach across the business to determine what was the right thing to do and to set the business up to improve performance. Anyone can cut costs for the short term, but we set out to do it in a sustainable and reliable way. We created a program we call Full Potential to look for sustainable ways to reduce costs and improve productivity. That program has taken more than a billion dollars out of our costs since we implemented it 2013 and that shows up in our results. Our all in sustaining costs are down 28 percent and our productivity is up 39 percent.”During the downturn, Newmont restructured its business model, sold off some assets and created a leaner, more nimble operation. It has paid off with the addition of two new mines and the acquisition of another, the Cripple Creek & Victor Mine in Cripple Creek, CO.“The gold industry had not seen a downturn in 12 years. We had half a generation that had not experienced a downturn, so helping them through that in an organized way and keeping a view toward the long term throughout the downturn was important. We were one of the few companies that continued to invest in assets,” he said."

Nov 1, 2016

By A Hekmat, M Fuentes, F Armijo, R Castro, F Rodriguez

Interpreting the behaviour of granular material and simulating the gravity flow are complex processes in cave mining methods. In this paper, a new Cellular Automata based code – FlowSim – is used as a flexible tool to simulate the gravity flow and subsidence zone in block caving mines. The simulation results of the gravity flow model in a real scaled mine as well as a scaled physical model are presented in this study. In this research, FlowSim was first calibrated at a mine, based on the information obtained from smart markers. These markers were located in five points of the second block of the Esmeralda sector, at the El Teniente copper mine, Codelco, Chile. The calibration was performed with the objective of reducing the discrepancy between the extraction zone defined by markers in the mine and FlowSim outputs. Regarding the mine data, FlowSim was calibrated with the minimum error of ten per cent between real and simulated results. Then, the calibrated FlowSim model was used to simulate the flow behaviour of a scaled physical model. This model was constructed in the Block Caving Laboratory of the University of Chile to scale down the same block of the Esmeralda sector with the scale of 1:200. The FlowSim outputs show that this software enables the simulation of the gravity flow of the scaled model with less than five per cent discrepancy in grade and dilution entry to the drawpoints. According to the obtained results, this paper recommends FlowSim as an appropriate tool which can improve the design of production level in block caving and can enhance the prediction of the subsidence zone and dilution entry.CITATION:Castro, R, Hekmat, A, Fuentes, M, Armijo, F and Rodriguez, F, 2016. FlowSim – a versatile flow simulation tool to quantify extraction and design alternatives for block caving, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 645–652 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Frédéric Bélanger, George P. Demopoulos, Pascal Coursol, Thomas Feldmann

"The use of scandium in industrial applications is expected to rise in the coming years, in large part due to the expected adoption of new, clean energy technologies such as solid oxide fuel cells or Sccontaining high strength aluminium alloys. Given that the supply of Sc is currently dominated by only a few countries (Russia and China) other sources for scandium extraction need to be investigated. This paper looks at different options for the recovery of scandium from waste solutions generated during the production of TiO2 pigments via the chloride process route. In particular, a direct solvent extraction (SX) approach and possible options for concentrating scandium before the SX step were investigated. It was found that the presence of Ti during solvent extraction causes severe formation of stable emulsions, which can complicate the successful application. This was particularly a problem after multiple contacts of the organic phase with fresh aqueous phase. On the other hand it was noticed that the presence of certain elements in the solution, e.g., iron, could possibly be utilized to concentrate scandium in a solid precipitate.INTRODUCTIONMany newly developed high-tech products depend on the use of chemical elements that are only produced in very small quantities. This can result in high and fluctuating prices, as can be seen from Figure 1, which may cause substitution with inferior alternatives, if possible at all (Reck & Rotter, 2012; US Dept. of Defense, 2013; Whittaker, 2011). One example is scandium (Sc) a member of the extended rare earth element family. There are only a few scandium ore deposits, but most Sc is produced from the processing of by-products of other metallurgical processes (Melcher & Wilken, 2013). Increasing demand for scandium metal and oxide (Sc2O3, scandia) is coming from its increased use in applications such as ceramic lasers (Li, Ikegami, & Mori, 2005; Rainer et al., 1982), high strength aluminium alloys (Lathabai & Lloyd, 2002) as well as solid oxide fuel cells (SOFC) (Thijssen, 2011). Especially, the spread of climate friendly SOFC’s, which are a commercial product today (Bloom Energy, 2014), is expected to be a main driver for future Sc2O3 demand. However, the rate of market penetration of this green technology depends on the availability of high purity Sc2O3 (>99.999%), since it specifically contributes to longer life-time and better safety of the SOFC’s (Bloom Energy, 2014; Irvine, Politova, & Kruth, 2005)."

Jan 1, 2016