Search Documents

By A. L. Hinde

The steady-state and dynamic behaviour of semi-autogenous grinding (SAG) mills are arguably best described using a population model that caters for the breakage kinetics and the material trans-port of rock and pulp inside the mill. Breakage kinetics are usually expressed in terms of a specific breakage rate function and a separate primary breakage distribution function. Material transport usually invokes the concept of a specific discharge rate function. Unfortunately, the breakage rate and breakage distribution functions for SAG mills are very difficult to estimate uniquely from plant data alone. Simplifying assumptions must be made to over-come this problem, which leads to many unresolved dilemmas with regard to whether or not the de-rived functions are accurate, precise, and reflect reality. For example, it is sometimes assumed that the breakage distribution function for a SAG mill treating run-of-mine ore can be derived from laboratory dropweight and tumbling tests on small rocks in narrow size ranges. Such tests hardly reflect the environmental conditions likely to be encountered in a pilot or production SAG mill where there is a wide spectrum of particle sizes. It is shown that the dilemmas associated with standard population balance models (models that utilise separate breakage rate and breakage distribution functions) can be overcome by expressing breakage behaviour inside a SAG mill in terms of a single function. This function is an energy-based cumulative breakage rate function defined as the fractional rate at which particles and rocks coarser than a given size break to below that size per unit specific energy input. A model for SAG milling is formulated, which invokes the concept of a cumulative breakage rate function. Comparisons are made between the mathematical structure of this ?simple model? and standard population balance models. Perhaps the most attractive feature of the ?simple model? is that the cumulative breakage rate function can be uniquely estimated from measurements of size distributions and mass flows of the feed and discharge streams together with the size distribution and holdup mass of the mill charge. Such measurement can easily be made at pilot scale. It is concluded that this simplified approach to SAG milling may turn out to be the quickest way to fully describe and quantify the performance of these very complex mills.

Jan 1, 2014

By P Stephenson, G Mosher, M Berry, C Arnold, P Stoker

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Globally, private minerals companies considering the transition to a public company and entrepreneurs looking to create a new public company through, for example, an initial public offering or by a reverse takeover have many options. For companies with assets around the Pacific Rim, there are arguably five key stock/securities exchanges that actively promote international minerals company listings, and these are located in Australia, Canada, Hong Kong, Singapore and the United Kingdom.Listing on any of these exchanges requires a range of technical, commercial, financial and legal documentation. Each exchange has specific rules and requirements for technical documentation to support the listing process. Once listed, each exchange also has specific rules for technical information to meet ongoing compliance requirements. The nature and detail of this documentation differs for the five exchanges.This paper presents statistics on the minerals company listings on each exchange and provides an overview of the technical documentation required to prepare for an initial listing and ongoing compliance.CITATION:Berry, M, Stoker, P, Stephenson, P, Arnold, C and Mosher, G, 2015. Technical considerations of public listing and ongoing compliance for minerals companies , in Proceedings PACRIM 2015 Congress, pp 101–108 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

The title of this address was selected before I had an opportunity to consider in detail the matters that I would like to discuss. Accordingly, I chose a very broad subject-so broad indeed that it would be foolhardy for me to attempt to deal with more than a few aspects of it. I do not propose to touch. at all on the developments to date of our mining and metallurgical enterprises, beyond paying a sincere tribute'to the skill and enterprise of those who have established an international reputation for Australian mining and metallurgy. I would rather look ahead and discuss certain factors that will play a decisive part in the future development of our mineral resources. I do this in no dogmatic spirit, and I hope that my remarks may lead to discussions which will stimulate action where it is needed.In recent years my colleagues and I have been forced by circumstances to give consideration to problems in the fields of mining and geology, and in process metallurgy, which lie outside the scope of our own research work. People come to us with metallurgical problems because they know of no more appropriate place to go, and it is distressing to have to inform them that it is nobody's job to offer them advice and assistance. I want to suggest to your Institute that it should press strongly for the provision of properresearch facilities for the mining and metallurgical industries, such as aready exist in most enlightened countries. In such countries, those connected with the development of mineral resources are able to obtain information and advice from Geological Surveys, Mines Departments or Bureaux of Mines, which offer far more comprehensive services than are available in this country.Before discussing specific technical problems of the mining and minerals industries, I shall enunciate certain general principles that I believe should be followed in respect to the technical side of the development of all Australian industries. The problem can, I suggest, be considered in three parts-technical education production, and research. I shall confine my remarks mostly to the research aspect, for it is with this that I am most familiar.For the efficient development of any industry in Australia, it is essential firstly that We should learn what is going on abroad, and secondly that we should simultaneously conduct independent research. In the latter sphere the Governmeht'departments and the private companies' or groups of companies should have complementary functions, the former concentrating on problems common to a number of companies or industries, and the latter on their oWn individual problems. It is essential to the continued existence of Australian industry that both company and govern...

Jan 1, 1944

By P. C. A. Maia, J Alexandre, F. A. J. Saboya, A. R. G. Azevedo, G. C. Xavier

"This work shows the characterization of clay and the granite waste by-product from the sawing process of the granitic blocks, used as raw material for brick ceramic. Besides, shows the degradation of the ceramic material obtained with different by-product contents in the waste after lab test degradation, is investigated. The clay is obtained from mine use areas of ceramic industry in Campos-RI and the waste is originating from of the area of Cachoeiro-ES, an important center of decorative stone in Brazil. The mixes were made by the addition of 0% up to 10% of the waste in the raw material. After drying and firing up to 900°C, obtained prismatic pieces were considered intact. Physico-mechanical properties were obtained from wet and drying tests in laboratory considering 50 and 150 cycles. The results showed that the use of powder byproduct has a considerably influence on the weathering and strength of the material.IntroductionThe ornamental rocks and coating defines the most promising areas of business in the mineral sector [l]. In this context, the Espirito Santo appears as the main Brazilian state in production and export of ornamental rocks, representing 47% of national production [2] which in tum is one of the economic sectors most representative of this State, due of its transport logistics and port vocation that facilitates the export of such products.It is estimated that the state of Espirito Santo there are approximately 1,200 companies dedicated to the activities of ornamental rock by providing 20,000 direct jobs [ 1]. These mobilize support activities, such as companies that provide machinery, equipment and supplies for industries, including service providers for maintenance.However, the production of rocks produces about 15,000 tons of granite waste/month [3] only in the municipality of Cachoeiro ltapemirim-ES. This is justified by the presence of more than 500 extraction industries, cutting and processing of stone, with about 900 looms, waste generators.According to [4], there is great potential for the use of granite waste in red ceramics introduced for the manufacture of bricks, blocks structural ceramics. and other ceramic products, especially when evaluated on exposure to weathering."

Jan 1, 2014

By Vijaya Bhushan Rao, Jason Redgers

A substantial lifestyle destination in the United Arab Emirates, in the Emirate of Abu Dhabi comprising of 1315 villas, town houses and non-residential leisure facilities is built over an area of 280 hectares of former mangrove areas, natural sands and reclaimed lands. Large-scale subsoil investigations including field and laboratory testing carried out dividing the entire site in to 7 clusters. This investigation revealed alternating layers of loose sands and silty clays within the load influence zone of planned foundations, showing susceptibility to excessive settlements. Therefore, ground improvement works were undertaken using a combination of stone columns, Rapid Impact Compaction (RIC) and excavation and replacement of soils plus a 0.4m thick load transfer platform. This was necessary to limit the settlements, increase-bearing capacity and prevent long-term settlements. 30 no’s of full-scale Zone Load Tests, ZLT were carried out each for a duration of 30 days in order to ascertain the anticipated long-term settlements in the clay layers. In addition, further testing of electrical cone penetration tests, CPT, and Plate Load Tests, PLT. The use of Priebe and Asaoka’s observational procedure were applied to predict the final settlements and the use of back-analysis from the 30 days Zone Load Tests, ZLT results to establish the site-specific consolidation parameters in clay layers to optimize the design and ground improvement works.

Sep 8, 2021

By Yuemin Zhao, Daniel Tao, Xinxi Zhang, Qingru Chen, Maoming Fan, Zhenfu Luo, Xiuxiang Tao, Guohua Yang

Coal is currently cleaned with the minimum of size reduction, fine particle processing, recovery, and tailings disposal are major problems. Adequate water resources are not always available. For example, two thirds of China's coal is located in arid areas. Hence, dry separation provides an alternative approach. Of the dry coal separation methods available, air dense-medium fluidized beds have been used to separate 50~6mm coal efficiently. However, excessive bubbling and back mixing of the separated solids in the air-dense media fluidized bed causes the high lower size limit of 6mm for the feed material, this affecting the preparation efficiency. Based on prior study on air-fluidized dense media for 6~50mm coal preparation, this paper presents methods and test results on the fine coal dry classification, static electricity beneficiation of 0~0.5mm coal, and magnetically stabilized fluidized beds for separating 0.5~6mm coal.

Jan 1, 2005

By Rob van Opbergen, Edo Engel

The highly dynamic economic climate of recent years has tightened the operating envelope for steel producers world-wide. Steel producers continue to experience immense pressure to respond quickly to changing circumstances and the focus has shifted towards efficiency improvement and maximizing flexibility in operations. The ability to safely stop, restart and ramp-up production facilities has become essential. Establishing this level of flexibility, without sacrificing efficiency, requires sound process control, fit-for-purpose process management practices and solid know-how and experience regarding special situations in blast furnace ironmaking operations. The same business environment that demands this increased flexibility has made it increasingly difficult for steel producers to sustain sufficient knowledge about these situations. While many experienced, senior operational staff have retired, a new generation of ironmaking specialists has acquired its hands-on experience over more recent decades, during which these process situations have been much less frequent than before. Over the past 10-15 years, the requirement in the industry for external operational support during e.g. blast furnace blow–downs, salamander tapping and restarts after planned and especially unplanned stops, has become increasingly frequent. This article presents a number of these cases from a process management perspective as well as with regard to project organization and optimized cooperation between internal and external teams of experts.

Oct 1, 2019

By Liang Zhen, Jian-Tang Jiang, Guo-Ai Li, Xiao-Ya Wang

"Deformation behavior of 2A97 aluminum alloy containing coarse secondary phases was studied using uniaxial hot compression (HC, 340–490°C, 0.4001–1 s-1). The flow stress could be described by a Zener-Hollomon parameter in hyperbolic sine function with the hot deformation activation energy of 237 kJ/mol. Based on the experimental data and dynamic materials model, processing maps were generated to demonstrate the hot workability of the alloy. The coarse secondary phases experienced dissolution by varying degree under different deformation temperature, which producing different effects on the microstructure evolution. When deformed at relatively low temperatures, a mass of fine grains shaped up in the original grains and grain boundaries, and the dominating deformation mechanism was believed to be dynamic recrystallization. As the deformation temperature rising to 490°C, most secondary phases disappeared and few recrystallized grains were observed, indicating that the secondary phases dissolved sufficiently along with dynamic recovery occurred during the hot deformation. Particle stimulated nucleation related to the coarse secondary phases was believed to promote the recrystallization and the recrystallization behavior was sensitive to deformation temperature.INTRODUCTION Al-Li alloys has received much attention as new promising structural materials in the aircraft and aerospace industries, due to their lower density, higher elastic modulus and improved fatigue crack growth resistance in comparison with the conventional commercial aluminum alloys (Ou Ling, 2015). 2A97 alloy is one of the 3rd generation Al-Li alloys targeting at comprehensive improvement of aviation aluminum alloy and applications for wing spars and ribs to other internal structures for transport aircraft. Al-Li alloys are usually formed by hot deformation, either by rolling or extruding. The deformation behavior and resulted microstructure evolution during the forming process mainly dominates the formability of the alloy and the serving performances as well. Therefore, the deformation behavior and microstructure evolution at elevated temperature need be made clear for optimizing the hot processing parameters and controlling microstructure evolution."

Jan 1, 2018

By S Servant

In the mine of this study, cemented hydraulic backfill is placed under the form of a slurry at a percentage of solid by weight varying from 50 to 65 per cent. This slurry settles and cures in the stope. During this process an important amount of water must be drained from the stope. Field observations in the case studied here show that the geometry of the drains system has a significant impact on the drainage of the stopes. The mode of filling produces a backfill showing an evident stratification typical of a sedimentation process. In situ observations on this material show that this stratification translates into a very strong heterogeneity in the physical properties of the cemented backfill. This heterogeneity should affect the hydraulic conductivity of the backfill in the stope. In order to study this aspect, finite element simulations were performed. This paper presents the results of these simulations, where the impact of this stratification on hydraulic conductivity is related to the performance of the backfill drainage system for various geometry. This preliminary study is aimed at providing a better understanding of the role of the drains in the dewatering process of the backfilled stope in the case of this mine.

Jan 1, 1998

By Servant S

In the mine of this study, cemented hydraulic backfill is placed under the form of a slurry at a percentage of solid by weight varying from 50 to 65 per cent. This slurry settles and cures in the stope. During this process an important amount of water must be drained from the scope. Field observations in the case studied here show that the geometry of the drains system has a significant impact on the drainage of the stopes. The mode of filling produces a backfill showing an evident stratification typical of a sedimentation process. In situ observations on this material show that this stratification translates into a very strong heterogeneity in the physical properties of the cemented backfill. This heterogeneity should affect the hydraulic conductivity of the backfill in the scope. In order to study this aspect, finite element simulations were performed. This paper presents the results of these simulations, where the impact of this stratification on hydraulic conductivity is related to the performance of the backfill drainage system for various geometry. This preliminary study is aimed at providing a better understanding of the role of the drains in the dewatering process of the backfilled stope in the case of this Mine.

Jan 1, 1998

By Tom Snyder, John Brulia

PART 3 – UN Identifi cation Markings for the Highway Transportation in Commerce of Bulk Explosives, Oxidizers, and Combustible Liquids

Jan 1, 2015

By W. Dziurzynski

The present article sets forward the results of field tests that made it possible to validate the mathematical model used in the VENTGRAPH ventilation engineer programmes. The case considered relates to the introduction of a new heading to the ventilation network of the mine. The utilisation of computer programmes in practice is justified by the necessity of ensuring expected performance and secure conditions in the network of mine headings, where - for example - plans are being made to utilise the transport dip-heading, taking into consideration fire and methane hazards. In the article we have presented the methodology of preparation of a database for computer programmes of the VENTGRAPH system, obtained on the basis of ventilation measurements. The next step consists in the execution of a design of the modified network and prediction, this on the basis of heading geometries, of parameters characterising the flow of air for the designed headings. Due to the fact that the heading was in the final stage of driving, following its introduction to normal operation and the stabilisation of flow values it was possible to retake ventilation measurements, which validated the results obtained through computer simulations. In order to execute measurements of the volume flow in the dip-heading, we employed a new wireless multipoint measurement system to determine the velocity field of air in the mine heading; the results are characterised by a high accuracy of measurement. As a part of fire prevention and incident management planning, a series of underground fire case studies for the a validated network flow model has been made. Results of simulations show the capabilities of the FIRE module of the mentioned software, including assessment of stability of flow directions and hints on counter and preventive measures for particular locations of fire.

Jan 1, 2009

By V. E. Elliott, C. L. Meyette

THE conditioning of semifinished steel products such as billets, blooms, and slabs to remove surface defects before further processing to finished products is a necessary accompaniment to steel mill rolling operations. A knowledge of the kinds of defects which occur and of the conditions in melting, teeming, and rolling that may lead to their occurrence is favorable to the production of quality products. Surface defects may be classed as either of mechanical origin such as those that occur in the heating and rolling operations and include breaks, tears, guide marks, mechanical laps and the like, or they may have been in the ingot before heating and rolling. Examples of the latter are ingot cracks, blow-holes, scabs, and inclusions which lead to the numerous known types of seams -and surface flaws. Most of the common types of surface defects and methods for their identification by visual examination or by the aid of macro-etch tests are well known. The conditions which caused their formation are also appreciably understood and this knowledge has been instrumental in the establishment of methods for metallurgical control. There are, however, defects of doubtful origin. In any endeavor to trace the causes for their occurrence, the question of first concern is: I. Whether they were formed in the rolling procedure. 2. Whether they existed in the ingot prior to rolling. In the case of semifinished products which are rerolled to finished products there is also the question of whether they were formed in the primary or in the secondary rolling. In metallurgical laboratories where numerous or routine examinations of the quality of rolled products are made over the course of time, there will doubtless be many puzzling cases of defect origin. Microscopic examination of the defects may, however, reveal a characterizing condition that can be used to classify them broadly with respect to their origin. Such a condition has been observed and, after detailed investigation, is described here with the thought that it may offer a useable and relatively simple solution to a bothersome problem. BASIS FOR CLASSIFYING In this discussion the term "mechanical type defects" will be used to designate those that have occurred as a result of the rolling operations such as in rolling from the ingot to billets, blooms, or slabs or in rerolling to finished products. The term "steel type defects" will he used to designate those that were present in the ingot prior to primary rolling or that were in the semifinished product prior to secondary rolling to finished product. The basis for distinguishing between the two types of defects lies in the relative degree of subscale formation surrounding them. Subscale is defined' as a zone of

Jan 1, 1948

The development of research activities at Risdon and the implementing of a policy of instrumentation in plant processes have, in recent years, entailed a considerable increase in research staff and created an urgent need for more space and modern laboratory facilities. The existing laboratories have been in use for 25 years and are now inadequate. New buildings have been authorized.The new buildings will comprise, firstly, a laboratory building of three floors giving a totai .floor space of approximately 11,000 sq.ft., and a pilot plant building as an annexe to the laboratory building, of approximately 4,900 sq.ft. The laboratory building will accommodate from 20 to 22 research workers, and additional plant operatives will be used for the control of processes in the pilot plant building. The new buildings are designed to provide facilities for three principal functions; the investigation and improvementof existing processes, the development of new processes up to the pilot plant stage, and the control and maintenance of instruments.LOCALITY AND ORIENTATION OF BUILDINGSThe site of the buildings is elevated ground on the eastern side of the main plant, near the main entrance and general office building. There will be no obstruction to sunshine at any time of the day, and the laboratory building will command views of wide radius from wooded hills across the River Derwentto the open sea on the south-eastern quarter.The buildings are located to provide space for future extensions. The main laboratory building faces approx...

Jan 1, 1949

By Osamu Nishikokura, Jumpei Yamashita, Darrell Liebno, Malcolm Sheehan

"The Eglinton-Scarborough Crosstown Project builds a 19km LRT corridor that includes a 10km underground portion, between Keele Street and Laird Drive. The West Tunnel Contract (ECLC1-15) includes 6.5km of twin EPB TBM bored tunnels with a 5.75m internal diameter precast concrete segment lining (PCTL), between Keele Street and Yonge Street. This paper summarizes the overall scope of work, the technical challenges faced and innovative solutions developed by the contractor during the TBM move across an existing subway tunnel using state of the art high capacity strandjack gantry crane.1. PROJECT OVERVIEW The Greater Toronto and Hamilton Area (GTHA) is Canada’s largest urban region, populated with over 6 million people, and is one of the most rapidly growing regions in North America. One forecast estimates that the population of this region will increase to 8.6 million by the year 2031. In September 2008, Metrolinx, an agency of the Government of Ontario, launched a 25-year regional transportation plan named “The Big Move” to cope with the expected increase in transportation demand. The Eglinton-Scarborough Crosstown, one of the projects included in “The Big Move”, is a light rail transit (LRT) that will run across Toronto in an east-west direction between Mount Dennis and Kennedy along Eglinton Avenue. In October 2012, the West Tunnel Contract of the Crosstown LRT (ECLC1-15) was awarded to Crosstown Transit Constructors (CTC), a joint venture between Obayashi Canada Ltd., Kenny Construction Company, Kenaidan Contracting Ltd. and Technicore Underground Inc. The project includes approximately 6.2 km long twin bored tunnels, 9 cross passages, 1 emergency exit building, 7 sets of station headwalls, and an intermediate pair of extraction and launch shafts. Each of 6.5 km long twin tunnels are divided by the existing subway station into two drives: the first half from the launch shaft LS-1 (west of Keele Station) to the extraction shaft ES-1 (west of Eglinton West Station), and the second half from the launch shaft LS-2 (east of Eglinton West Station) to Yonge Station, as shown in Figure-1. The TBMs are extracted at ES-1 and moved to LS-2 over the existing Yonge-University Subway Line at Eglinton West Station before resumption of tunneling at LS-2."

Jan 1, 2016

By James Noll, Sam Janisko

Underground miners are exposed to some of the highest levels of diesel particulate matter (DPM) in the United States. Therefore, it is important to monitor the exposure of miners to DPM, but it can be difficult because of the complex composition of DPM and the number of interferences. Currently, elemental carbon (EC) is used as a surrogate because it makes up a significant fraction of the DPM and is not affected by interferences. Standard measurement methods for EC can be time consuming and only record end of shift results. In this research, a laser absorption technique that enables one to measure EC concentration in near real time was shown to be a beneficial tool. The real time data showed that the fresh air being drawn into a stone mine was not properly reaching the working area and needed to be redirected to decrease DPM concentrations. The real time data also provided a more accurate efficiency ofan environmental cab compared to just using the standard method by detecting the opening of the cab's window and door. The EC optical monitor was also worn by researchers in a mine to show how it can give not only the average concentration for the shift but also reveal when and where a miner is exposed to DPM. Keywords: Laser absorption, diesel, elemental carbon, mining, exposure

By Rolf S. Paine

The Bureau of Mines studied the presplitting technique used for control-ling overbreakage in the walls of a vertical shaft at the U.S. Army Corps of Engineers Littleville Dam project near Huntington, Mass. The periphery of the shaft, the dimensions of which were 16-1/2 feet wide by 21 feet long and 52 feet deep, was presplit (cracked) in the solid to a depth of 48 feet prior to full-depth sinking. Presplitting prevented overbreak in a fairly soft schist and provided sound self-supporting walls which required very little scaling.

Jan 1, 1965

By R. A. Egen

The purpose of this book is to provide an indication of what good hoisting practice is and how it might be achieved. To this end the book contains discussions of equipment and inspection and maintenance procedures developed and used by mining people in striving for safe, reliable hoisting equipment. Most of this information comes from domestic practice; the rest is foreign, notably from Canada. Most things discussed have long proved their general worth, and others promise to; a few are beginnings. However, nothing is conjectural or theoretical; the practices described herein are in use somewhere in the mining world. The stress is on equipment in use; it is not a design-guidelines manual. Nevertheless, there are some sections dealing with design material since it may be of value in a maintenance/ replacement sense. Mine hoisting installations encompass such a wide variety of equipment and conditions that it is impractical to specifically cover them all. This book mainly treats conventional systems using conventional components with some discussion of the more common unconventional (special) systems in use. There is no recognized definition for a "conventional" mine-hoisting system. Herein the term means those systems most commonly used in daily operations for transporting men, materials, and product-electrically driven drum and friction hoists, with guided conveyances running in vertical or inclined shafts. Beyond this, what "conventional" means is probably best illustrated by the topics discussed.

Jan 1, 1975

By J. W. Bridge

Triaxial compression tests at various confining pressures and temperatures, as well as tangent modulus tests using ultrasonic waves, were conducted for wax-coated granular composite materials. The material used is a surface for Thoroughbred horse racing. The purpose of these tests is to examine how track shear strength and tangent modulus at a range of loads respond to changing temperatures. Previous work has shown that a wide range of operational temperatures are experienced which have been reproduced in the lab. Using differential scanning calorimetry, it is confirmed that these operational temperatures correspond to distinct thermal transition regions for the wax that is used to coat the sand in these surfaces. Preliminary results show that both shear strength and tangent modulus are sensitive to temperature changes with maximum strength and modulus correlating with major DSC wax transition regions.

Jan 1, 2010

By Lifeng Zhang

The transport of fluid, heat ,and particles (bubbles and solid inclusions) in flowing molten steel is investigated in steel refining ladles, the continuous casting tundish, continuous casting mold and strand, and steel ingot casting processes. The two-equation k-?? model is used to simulate the turbulence. Multiphase fluid flow is numerically simulated with a Lagrangian-Eulerian approach, an Eularian-Eulerian approach and the Volume Of Fluid (VOF) method. The simulation can predict inclusion trajectories, inclusion removal fraction, free surface waves and other phenomena, which can be used to optimize these important metallurgical operations.

Jan 1, 2006