Search Documents

By G. Rehder

The release of methane as free gas from the seafloor into the water-column well within the hydrate stability field is a natural process observed today in various ocean settings, such as the Cascadia margin, the Black Sea, the Guayamas Basin, and the Gulf of Mexico. The subsequent dissolution of gas bubbles into the water-column determines the vertical distribution of aqueous methane in the water-column and the upwards methane flux. Understanding this process not only is essential to describing the impact of natural deep-sea gas seepage, but also to assessing the hazard potential from blowouts and offshore exploitation activities, which are steadily expanding to greater ocean depths. Furthermore, the fate of methane from seeps contributes to scenarios of global change in the past and future involving the large scale destabilization of gas hydrates on a. We recently reported on the extended lifetime of methane bubbles within the hydrate stability field due to the formation of a hydrate skin (Rehder et al., 2002), based on in situ measurements of methane and argon bubble dissolution in the depth range 400 to 800 m. More recently, these observations were extended to depths from 900 to 1500 m. Single bubbles were injected from the ROV Ventana into an attached, back-illuminated, flow-through imaging box. The ascent of individual bubbles within the imaging box was recorded with Ventana?s HDTV camera system by piloting the 3-ton ROV upward, at the bubble rise velocity, for up to 400 m of vertical transit. Observed rise velocities were approximately 30cm/sec for all depths. Post-dive analysis of the HDTV video allowed detailed measurements of the bubble shrinking rates. The results of the earlier and new experiments lead to the following conclusions: (A) Methane bubbles released below the hydrate stability field showed markedly enhanced lifetimes, attributed to hydrate skin formation. The change in radius with time, dr/dt, varied from -7.5 micrometer/s above the hydrate stability field to about -1 micrometer/s at the deepest release depth. (B) Bubble lifetime within the hydrate stability field increased with distance in P-T space from the hydrate phase boundary. (C) Before hydrate skin nucleation, dr/dt for CH4 bubbles was comparable to dr/dt above the hydrate stability field. Although variable, the onset time for the hydrate skin effect to occur generally decreased with distance from the hydrate phase boundary (super-pressurization and super-cooling with respect to hydrate formation). (D) Even before the onset of the hydrate skin effect, a slight decrease of dr/dt with increasing depth was observed.

Jan 1, 2005

By Atta Ur Rehman, Kwame Awuah‑Offei

This paper examines the effect of bucket geometry (cutting blade profile, floor profile, and blade thickness), speed, motor power output, and muckpile particle sizes on bucket penetration and draft for rubber tire loaders. The work uses a 1:16 scaled model of a load-haul-dump in full factorial experiments to examine the effect of the variables on penetration and maximum draft. The results show that speed and motor output are positively correlated to penetration and draft; muckpile particle size is positively correlated to penetration and negatively correlated to draft (p < 0.0014). The results show that buckets with a semi-spade cutting nose profile yield the highest penetration (mean 118.30 mm) followed by those with the spade (mean 108.88 mm), which also yield higher penetration than those straight blades (mean 95.19 mm). Bucket floor profile and blade thickness had no significant effect on penetration or draft. Also, we determined that increasing the speed and motor power output, simultaneously, can reduce bucket penetration. Thus, operators should not waste energy for no additional gain or even loss in bucket penetration. Also, the work finds speed and motor power output each combine with muckpile particle sizes to affect bucket penetration. This research furthers our understanding of the effectiveness of different bucket geometries in improving penetration and reducing draft for rubber tire loaders.

Oct 29, 2021

The 27th Regiment of Engineers was organized in the Army not long ago for special mining service at the front (or, we might even say, in advance of the front). In military engineering in warfare, the "sappers and miners" are one of the ancient branches of the corps of engineers; but in modern warfare the importance of this service has been greatly magnified. The 27th Engineers is a. special mining regiment, which is being recruited from mining engineers and miners from all districts of the country, already containing representatives from all the mining states between Arizona and Montana and from the Atlantic to the Pacific Coast. Those of us who cannot go to the front should not-be content to tell the young fellows to go, and then forget them. We want the men of the 27th Engineers to know that they represent our industry and their industry; and that the industry is going to think about them and back them up. Expressing the above views, the Engineering and. Mining Journal instituted a fund for the aid of the 27th Engineers. It has already raised a considerable sum of money, and contributions are coming in fast; but there is no limit to what is wanted. This money is being spent in providing the regiment with athletic equipment, both outdoor and indoor; with games for the barracks; with cigarettes and smoking tobacco; with contributions to the funds of the several companies that the men raise among themselves. It is contemplated, moreover, that there will be need to extend aid and comfort to some of the families whom the men have left behind. Contributions of books, sweaters and other knitted articles are also being received.

Jan 3, 1918

By Igor Kuzymin, Isaak Maximov, Iuriy Akkerman, Galina Aksenova, Valentina Sentemova, Nataliya Trubechkova

"The Russian Federation possesses large reserves of oxidized ferruginous quartzites. These ores are currently mined together with magnetite ores and are stockpiled on account of unavailability of an efficient processing technology. This paper presents the results of investigations performed on the ores from the largest oxidized ferruginous quartzite deposit located in the Kursk Region iron-ore basin of Russia. The objective is to produce concentrate with iron content at least 66% and silica content within 5%. A processing technology was, developed under laboratory conditions, which included ore preparation, wet magnetic separation in weak and strong fields and reverse cationic flotation with addition of caustic soda, dextrin and Lilaflot 811M (alkoxy propylamine) collector from Akzo Nobel. The developed technology produced iron recovery concentrate with iron content of nearly 67%, and that of silica - 4.1%, iron recovery into concentrate being 72.6%."

Jan 1, 2014

By J. P. May

This U.S. Bureau of Mines report identifies and evaluates factors responsible for dump-point accidents involving mobile mining equipment. Information regarding the occurrence and severity of the accidents, the industries affected, the types of equipment involved, the primary and contributing causes, and pertinent Federal regulations is included. The aim of this report is to provide information that will aid mine operators in the recognition of hazards associated with mobile equipment operation near the dump points of stockpiles and waste dumps.

Jan 1, 1990

By Wm. C. Coffin

THE refractory linings of open-hearth steel furnaces above the bath line are subject to severe wear not only from the heat caused by the combustion of the fuel and the reactions of the bath, but also from the melting action of the gases when not controlled and directed, and from the scouring of the oxides, etc. with which the products of combustion are charged. The framework that encases or binds the furnace is made up primarily of an iron or steel pan in which the furnace proper is built, side and end buckstays, and tie-rods. The expansion and contraction are so great and variable that the bindings may be subjected to severe stresses unless the tie-rods are carefully adjusted in heating up the furnace, but they are most affected by direct heat and usually become deformed from that cause when the lining is worn thin and, sometimes, when sections of the lining fall in and expose some of the framework. A deformed framework displaces the skewback of the roof arch and tends to distort or crush the roof. Bent buckstays deform the front wall, causing the door frames to stand away from the lining so that the gases burn between the lining and the frames, destroying both of them. Frequently the frames are attached to the buckstays; then when the latter bend the frames usually break. Preventing the distortion of the framework and maintaining the economy of the refractories are real factors in the cost of steel making. Not only does the cost of general repairs and reconstruction add directly to the cost of steel produced, but the time lost in making repairs cuts clown the steel production and increases the overhead expense of both the furnace shop and its allied foundry or mills. Many years ago water-cooled equipment applied to iron blast furnaces made it possible to increase greatly not only the size and production of the furnaces but also the life of the lining. It also cut down the loss from frequent repairs. The open-hearth furnace is a much later invention, especially as a commercial factor; for though it dates from the Fred Siemens patent of 1856, much more progress was made in the Bes-

Jan 2, 1919

By G. Hargrave, K. W. Moloney, M. R. Stokes

In recent years drivage advance rates in the UK have in- creased from 35m per week in the 1980&apos;s to 100/150m per week possible today. These extended rates of advance have resulted in an increase in the potential methane, dust and heat generation at the drivage face. In order to disperse this additional pollutant load requires an increase of fresh air at the face. Although advance rates have changed, current auxiliary ventilation practice has not. UK mining law requires that the fresh air must be delivered to within 5m of the face. This has lead to the wide spread use of overlap auxiliary systems, since a pure forcing system set at this distance would lead to excessive airborne dust. UK mining law does not at present consider on-board mounted exhaust scrubber fans to constitute an effective overlap fan within mechanised drivages. In an attempt to determine whether working conditions could be safely and economically improved within mechanised drivages, a series of preliminary full scale gallery trials were con- ducted. A summary of the principal findings of these trials are presented together with an outline of a series of representative CFD simulations, scale model experiments.

Jan 1, 1997

By J. Sammarco

Proper illumination is critical to a miner?s ability to detect hazards in underground mines. Moving hazards are often located in the miner?s peripheral field-of-view, while slip/trip/ fall hazards are often located in the forward field-of-view. The objective of the research described in this paper was to determine if light-emitting diodes (LEDs) improve visual performance as compared to traditional incandescent (INC) cap lamps. The research presented focuses on comparative studies of a National Institute for Occupational Safety and Health (NIOSH) prototype LED, a commercial LED and an INC camp lamp. Thirty subjects participated in these studies, with ten subjects in each of the following age groups: 18 to 25 years, 40 to 50 years and 51+ years old. Visual per­formance was quantified by the subjects? speed and accuracy in detecting hazards, while visual performance for disability glare was quantified by the use of contrast sensitivity tests. Results suggest that LEDs with a visible spectrum containing a higher concentration of the shorter wavelengths can enable visual performance improvements with respect to disability glare, the detection of moving hazards in the peripheral field-of-view and the detection of floor hazards in the forward field-of-view. The NIOSH prototype LED cap lamp provided the best visual performance improvements for the older age groups in every test.

Jan 1, 2009

By W. J. Slatosky

As a means of effecting better control of endpoint temperatirres at the Jones & Laughlin basic oxygen furnace plant, a set of mathematical equations has been developed. The eqlutions are the product of a themlochemical anaysis of the process and aye designed to calculate the required scrap, lime, and hot metal additions in terms of a number of independent variables. Results of test heats have warranted adoption of this technique by the Prodrrction Department. BECAUSE of the autogeneous nature of the basic oxygen steel-making process, bath temperature can be controlled without an external fuel supply by charging the furnace with additions that are thermally balanced. The thermal requirements of the charge materials are such that, during the refining process, they throttle the heat generated by the metallurgical reactions in a manner designed to result in a speci-fied temperature at the completion of the heat. In the past, operating personnel at the basic oxygen furnace plant of Jones & Laughlin&apos;s Aliquippa Works relied on their experience and technical knowledge of the process to determine the quantities of charge additions needed to result in a finishing temperature in the range 2880"to 2920" F. (The charge consists primarily of 93 tons of scrap and hot metal plus an amount of lime sufficient to maintain a basicity ratio of 2.8 to 3.2). Estimates of these materials are based on a consideration of the effects on finishing temperature of 1) iron silicon content, having a variation of 0.8 to 1.8 pct; 2) iron temperature, ranging from 2250°to 2600°F; and 3)any excessive cooling of the furnace due to a production delay. The end temperature of the preceding heat also serves as a guide in that, if a heat was within the specified temperature range, the succeeding heat could be charged with materials of nearly the same proportions, provided the hot metal used in each of the two charges was of approximately the same temperature and composition. On the other hand, if a heat was outside the specified tapping range, or if the hot metal used in that heat was of different analysis and temperature from that of the iron to be charged, an adjustment in the proportion of additions is in order for the following heat. Due to the complex thermochemical behavior of the process and to the inexact and subjective nature of the described method of determining charge additions, consistently accurate temperature control was not to be expected. Therefore, those heats out- side the specified tapping range necessitated subsequent adjustments by either reblowing the cold heats for a suitable length of time so as to elevate the bath temperature to the desired level, or cooling hot heats with a proper amount of scrap. Because extra time is required to make these adjustments, production is delayed. In an attempt to devise a method for improving temperature control, an analysis of the thermochemistry of the process was undertaken. This, in turn, led to the development of a set of mathematical equations which enable the calculation of the quantities of scrap, lime, and hot metal needed to result in any specified tapping temperature range. The analysis was not intended to be a repetition of work done by others such as McMulkinl or ~hilbrook.&apos; It was meant to be an extension of their work so that charge additions could be calculated not in terms of silicon alone but, rather, as a function of all independent variables. This paper presents the derivation of these relationships, their effectiveness in controlling bath temperatures, and a method of utilizing them on an operational basis. The Heat Balance—The first step undertaken in the analysis of the problem was the enumeration of the pertinent variables. A list is presented in Table I where it is noticed that these quantities have been separated into the following three categories: important variables, variables considered as constants, and variables to be neglected. The breakdown was an arbitrary one designed to facilitate the analysis; otherwise, the mathematical treatment would have been exceedingly cumbersome and complex. Fortunately, experience has shown that these simplifying assumptions do not seriously impair the accuracy of the calculations. These variables along with the limiting assumptions listed in Table n were then used to write a heat balance of the process by applying the equation of continuity, Rate of Rate of Rate of Increase = Income - Outgo PI ] of Heat of Heat of Heat.

Jan 1, 1962

By Qingwei Wang

This study focused on acidic wastewater from producing sulfuric acid system in zinc smelter containing mercury 21.48mg/L, zinc 55.85mg/L, lead 38.50mg/L, copper 1.68mg/L, cadmium 10.25mg/L, As 29.86mg/L treated by biologics. The factors of pH value, the ratio of biologics to mercury, complexing time, hydrolytic time and temperature were studied in this paper. Experimental results indicated that at pH value 10, quantity of biologics to mercury ratio was 16, complexing time 30min, hydrolyzation time 20min, temperature at 40?, concentration of mercury in treated water was removed to 22.15µg/L. At same time heavy metals such as Zn, Pb, Cu, Cd, As was removed by biologics, the remained concentration in treated water was Zn 0.53mg/L, Pb 0.12mg/L, Cu 0.01mg/L, Cd low to 0.01mg/L and As 0.023mg/L. According to EDAX analysis, mercury content in complexing sediment reached 28.49% easily to recycle as raw material and low concentration of heavy metals in hydrolytic sediment easily to dispose and treat.

Jan 1, 2009

By G. F. Zhang

Yunnan mineral is a kind of containing Ta-Nb rare earth deposit, the most potential economic valuable element in it is Sc, and raw mineral has 17.0 g/t Sc. Take the character of Sc into account, the key problem in producing scandium chloride molten salt by adaptive technology is how to man-ufacturer anhydrous scandium chloride molten salt. During the course above, the key problem is that preventing Scandium chloride from being hy-drolyzed into ScOCl. The ScOCl content of molten salt not only affect purifying scandium but al-so do harm to the production of Mg-Al alloy. In order to restrain the creation of ScOCl, add ammo-nium chloride into molten salt. As long as ScOCl is created, it would be chloridized. Thus, during the course of dehydrating anhydrous chloride molten salt this method prevents scandium from hydrolyzing. Accordingly, the key phase of this producing course is eliminate ammonium chloride and the surplus crystal water, and the most crucial of it is restrain scandium chloride from being hydrolyzed into ScOCl. This research analyzed the theory that ammonium chloride is trend to be hydrolyzed into ammo-nium chloride, and propose the research scheme of restraining this process from creating ScOCl. The new process of restraining the generating of ScOCl and dehydration for crystal water rare earth chloride is adopted: Inert gas temperature increases rapidly to a certain degree to eliminate ammonium chloride and crystal water. The experimental research were done such as : the temperature of eliminating ammonium chloride and crystal water, amount of ammonium chloride, time, temperature growth speed, influence of inert gas flow toward to scandium percent hydrolysis, whereby, we conclude the optimal process condition in this period: Temperature: 400°C, proportion of oxidized scandium and ammonium chloride is 1:1.5(Proportion of oxidized scandium and additional salt is 1:5.4), time is 120minute, temperature growth speed is 10?/min inert gas flow is 5L/min.

Jan 1, 2014

By Butler, P. B.

TRIPOLI is a rather unusual form of silica, which thus far has been found in commercially valuable quantities only in the neighborhood of Seneca, Mo., although there are numerous deposits of somewhat similar materials in several southern states. The latter have not, however, attained any position of real importance, due undoubtedly to definite structural limitations which have rendered them less suitable for the particular uses that have given tripoli its principal outlets. Raymond B. Ladoo, mineral technologist, says&apos;: "Since that time (1880-90) the term tripoli has with increasing definiteness been reserved for the Seneca material, and other siliceous materials of similar origin and physical properties."

Jan 1, 1928

By T. Price, H. A. Holl, A. P. Greenough, A

UdIN, Shaler, and ulff&apos; first used wires for the determination of the surface energy of a solid metal. A gage length was marked by tying knots in the wires, which were then suspended in a cylinder of the same metal, heated in an inert atmosphere for the appropriate time, cooled to room temperature, and finally removed from the furnace so that the lengths of the wires could be measured. With iron wires, difficulties associated with deformation during the phase changeszp3 made it necessary to measure the gage lengths at the tem-

Jan 1, 1964

By D. P. Plute

The mechanization of the materials management function must contribute to the overall goal of optimization of profits. A computerized system contributes to the profitability of the company by saving more than it costs to operate. Design and implementation of the sys- tem must respond to the needs of users, the operating environment of the property, and must support the objectives of materials management. Three basic functions interact within the scope of materials management. They are inventory control, purchasing, and warehousing which have the following objectives: 1) Inventory control-to request materials in a timely manner and in quantities that provide the best level of support to users at the lowest cost. 2) Purchasing-to purchase requested materials and services at the required time and at the lowest cost. 3) Warehousing-to efficiently receive, store, and issue materials and to prepare accurate transaction documents for the activities. The development of the mechanized materials management system will require a plan and objective analysis by management and system users of system requirements. A typical plan would include: 1) System Design Objectives-the development of objectives that support mechanization of the materials management function. 2) System Characteristics and Concepts- the development of key system concepts and characteristics, which identify the needs of materials management. 3) System Inventory Item Classification- development and assignment of inventory category codes to inventory items. 4) System Order Decision Rules-the development of decision rules and forecasting techniques to minimize the inventory investment and to provide acceptable support levels. 5) System Report Structure-the development of a report structure to support the goals and objectives of materials management. 6) System Report Design-the development and design of reports for effective utilization of the mechanized system.

Jan 1, 1979

By P. E. Fitzgerald, J. C. Gindlesperger

1. The Acidizer (Trade Publication of Dowell Inc.): No. 1. Aspects of Acidizing. No. 2. Inhibited Acid. No. 3. The Value of Acidizing. No. 4. The Chemistry of Acidizing. No. 5. Jelly Seal in Acidizing. No. 6. Loosening Stuck Drill Pipe. No. 7. The Geology of Acidizing. 2. J. C. Albright: Acid Is Being Used for Cleaning Intake Wells in Water-flooded Areas. Oil Weekly (Sept. 23, 1935) 24. 3. D. H. Bancroft: Acid Tests Increase Production of Zwolle Wells, Miller County, Arkansas. Oil and Gas Jnl. (Dec. 22, 1932) 42. 4. A. H. Bell: Possible Areas for Acid Treatment in Illinois. Pub. of Illinois- Indiana Petr. Assn. and lllinois Geol. Survey (1934) 49. 5. N. A. Best: Treating Limestone Formations Consists of More than Pouring Hydrochloric Acid in the Well. Oil and Gas Jnl. (April 5, 1934) 54. 6. L. G. E. Bignell: Sealing Off Salt Water from Oil-bearing Formations. Oil and Gas Jnl. (Jan. 30, 1936) 59. 7. L. G. E, Bignell: Acidizing Upper Limestone Formation Facilitated by the Use of Jelly Seal. Oil and Gas Jnl. (March 5, 1936) 30. 8. L. G. E. Bignell: Bailing, Shooting, Tubing and Acidizing Have All Been Tried in Deep Test at Binger, Oklahoma. Oil and Gas Jnl. (May 10, 1934) 38. 9. L. G. E. Bignell: Dowel1 Incorporated Increasing Its Field Service for Acid Treatment of Wells. Oil and Gas Jnl. (June 7, 1934) 62. 10. L. C. Chamberlain, Jr. and P. E. Fitzgerald: Oil Well Acidizing in Michigan. Mich. Acad. Sci. Papers (March 1937). 11. M. E. Chapman: Some of the Theoretical and Practical Aspects of the Acid Treatment of Limestone Wells. Oil and Gas Jnl. (Oct. 12, 1933) 10. 12. C. E. Clason and J. G. Staudt: Limestone Reservoir Rocks of Kansas React Favorably to Acid Treatment. Oil and Gas Jnl. (April 25, 1935) 53. 13. W. F. Cloud: Cleaning and Reconditioning Oil Wells—Reconditioning by Use of Acid (Petroleum Production 1937), 389. University of Oklahoma Press, 1937,&apos; 14. K. A. Covell: Developments in Eastern Production Practice. Acid Treatment of Michigan Wells. Amer. Petr. Inst. Prod. Bull. 213 (1934) 77; Oil and Gas Jnl. (May 31, 1934) 89; Oil Weekly (May 28, 1934) 17. 15. B. A. Cunningham: Acid Treatment of Lime Formations. Amer. Petr. Inst. Paper 901 (1933) 9D, 1-7. 16. 0. I. DeSchon: Pondera Production up 22,000 Barrels. Montana Oil & Min. Jnl. (Jan. 26, 1935) 1.

Jan 1, 1937

By V Malysiak, N J. Shackleton

In the flotation of platinum group minerals pyroxene is a major gangue mineral. This study shows using zeta potential and ToF-SIMS analyses that when pyroxene is exposed to copper, nickel and/or calcium ions in solution at alkaline pHs a surface reaction occurs between the hydroxy species, in the case of copper and nickel, or divalent calcium ions and the pyroxene surface which influences the floatability of the pyroxene. Following exposure to copper and nickel ions at pH 9 addition of SIBX resulted in the pyroxene floating readily. It is also shown, in the case of copper, that the activating effect of the adsorbed copper hydroxy species can be reduced by the addition of complexing amines prior to SIBX. Proposals are made to explain these observations.

Jan 1, 2005

By E. C. Baker

Costs of disposing of steel slag are estimated based on the present method and a proposed alternate method for a steel mill in the Pittsburgh area. Estimated cost data were calculated by the Bureau of Mines and do not reflect the investment and operating costs and credits of a specific steel mill and processing plant. The alternate method of steel slag disposal would result in an appreciable cost savings to the mill and concurrently supply the industrial and commercial markets with low-cost, high-quality construction materials.

Jan 1, 1970

By A. G. Lylie

Introduction At the Britannia Mining and Smelting Company&apos;s mill, the equivalent of 2,500 to 2,800 pounds of copper sulphate crystals per day is made from copper which is precipitated from the mine-water. This copper sulphate is used in the mill for the recovery of sphalerite by2 flotation. From 1932 until 1936 it was produced by exposing the precipitate to air for thirty days and then dissolving the oxidized copper with dilute sulphuric acid. In 1936, the flotation of sphalerite was discontinued and, when it was resumed in 1947, steps were taken to try to improve the former method. The present paper outlines the way in which this was done, and describes the plant and procedure by which copper sulphate is now being made, and by means of which an appreciable saving is being effected. Aboratory Tests The previous work had established that the precipitate, which consists mainly of metallic copper, must be oxidized before the copper would dissolve in dilute sulphuric acid. Various methods for oxidizing it were tried but in the early laboratory work the only suitable one found was to heat the precipitate to 600°C. and hold it at this temperature for two hours. When this was done, approximately 90 per cent of the copper became soluble in .acid. This percentage was considered satisfactory for practical purposes, but the cost of roasting was prohibitive because only a small amount of roasted precipitate was required each day.

Jan 1, 1951

The objective in control blasting is to reduce overbreak to control the final pit wall slope, shaft, drift, ditch, bench, etc. to the final planned excavation limit.

Jan 1, 1991

By Yvon T. Maurice

Under the auspices of the Federal-Provincial Uranium Reconnaissance Program, a geochemical orientation survey was undertaken in an area of uraniferous Lower Proterozoic (Aphebian) rocks near Cape Dorset in southwest Baffin Island. The main objective of this study was to establish a methodology for a future reconnaissance geochemical program using lake samples over a 300-mile Lower Proterozoic rock belt that occurs along the southern coast of Baffin Island. Mineralogical and chemical studies of known radioactive occurrences, combined with detailed sampling of secondary environment media in the vicinity of the showings. indicate that uranium is the most significant pathfinder, despite considerable enrichment of other metals in the uraniferous rocks, Significant geochemical patterns produced by uranium in lake waters and uranium in lake sediments have been obtained, but their relative usefulness depends on the distribution of carbonate bedrock, which in turn affect the bicarbonate content of lake waters. In southern Baffin Island, because of erratic variation in lake-water alkalinity, it is recommended that both water s and sediments be sampled on a routine basis. The need for lake-water acidification to prevent depletion of soluble metal ions in samples resulting from adsorption on the walls of the containers and/or suspended solid matter is discussed briefly. The base metal potential of the area was examined in some detail and found to be significant, particularly for a Lower Proterozoic gossanous formation that occurs throughout southern Baffin Island.

Jan 1, 1977