Search Documents

By D Laskovski, T Nguyen

Flotation surveying can be an extremely powerful means of determining opportunities for circuit optimisation and benchmarking. The type of survey employed depends heavily on the nature of the information required from the survey. It follows then that the type of survey determines the type of samples required; however, regardless of the type, the success or failure of a survey is often dependent on the correct used of appropriate sampling techniques at each sampling point. For a successful flotation plant survey it is vital that the correct samples be collected at the correct time in respect to the feed and each other. This paper discusses the current best practice sampling methods used in flotation surveying and discusses in detail the ideal sample masses based on theoretical analysis. Comparisons with JKTech’s database of real plant operations will then be made.CITATION:Laskovski, D and Nguyen, T, 2014. An investigation of current flotation survey sampling, in Proceedings Sampling 2014 , pp 99–106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By S. Annavarapu

"Fragment size distributions play an important part in the design and planning of block cave mining operations. Though several methods have been proposed for estimating fragment size distributions in advance of mining, the calibration of these estimating procedures to field measurements has been a challenge. The Block Size Estimator (BSE) program was developed for providing an assessment of primary fragmentation expected in a block cave mine using drill-core piece length data and joint characteristics from the exploration and geotechnical evaluation programmes. In order to validate the results from the BSE program, the drill-core piece length data and the joint characteristics in different rock types from the DOZ block cave mine in Indonesia were used to help generate fragment size distributions in different areas of the mine. The predicted fragment size distributions were compared with the fragmentation observed at the drawpoints during operation of the mine.This paper presents the details of the validation of the fragment size estimates by the BSE program using fragment size distribution data from the drawpoints at the extraction level at the DOZ block cave mine, and the challenges encountered in developing reasonable correlations between the estimated and measured fragment size distributions. IntroductionThe assessment of fragmentation is an important aspect of the design and planning of the block cave mining method, and forms an integral part of the design of the excavations at the extraction level and the selection of material handling systems for transporting the ore to the processing stations. Secondary blasting requirements can also be estimated based on the fragment size distributions developed for the block cave (Laubscher, 1994).Several methods of estimating fragment size distributions in block cave mines have been developed based on joint set parameters estimated from structural data from oriented core drilling campaigns and mapping of available excavations and outcrops. The BCF program (Esterhuizen, 1999) estimates the fragmentation using a combination of empirical, analytical, and rational methods to model the behaviour of materials during the primary and secondary fragmentation processes. The program JKFrag uses advanced tessellation of joint traces to create rock blocks and then generate fragment size distributions (Brown, 2002). Nickson, Coulson and Hussey (2000) presented the details of processing of the geotechnical data from the Mont Porphyre project, including an assessment of block sizes from the data collected on the core logging sheet. The distance between natural fractures was used to create distributions of block lengths, and a distribution of potential block sizes was estimated assuming that the blocks had equal dimensions in all directions. The results agreed closely with the results of the BCF program. Hadjigeorgiou, Grennon, and Nickson (2002) demonstrated the use of oriented borehole data to provide characteristic block size distributions for a mining project using a software package called Stereoblock, which generates a three-dimensional joint network for a given volume and calculates the volumes of blocks created by the intersections of these joints, simulated as circular planes. The distributions of joint orientation and joint spacing generated from statistical analysis of the oriented core data are used for the creation of the Stereoblock model. The diameter of the circular planes representing the joints is determined based on the mean and standard deviation of the joint trace length obtained from scan-line mapping."

May 1, 2019

By C. W. Dunham

FROM the primary gyratory crushing plant, described in MacLeod's article, ore is delivered to a large storage or surge bin from which it is carried by two transverse conveyors to the secondary crushing plant. The bin has a useful drawoff of about 13,000 tons, this being slightly over one half of the initial daily capacity of the Morenci Reduction Works. This arrangement provides sufficient storage to permit intermittent operation of the primary and secondary crushing plants without too close a coordination between the two.

Jan 1, 1942

By Michael Day, Paul Kos, Scott Brinton

A hydrogeologic characterization and impact analysis was performed for a proposed quarry at the Hitch Rack Ranch located in the Little Turkey Creek watershed southwest of Colorado Springs, Colorado. Continuous multiple channel tubing, nested piezometers, stream flow measurements, and mapping of known seeps were used to define the three-dimensional potentiometric distribution and areas of groundwater recharge and discharge. Water balance considerations, mass balance calculations, and potentiometric response to earth tides and barometric fluctuations confirmed that the granite fracture system in the ridge area of the proposed quarry has an extremely low bulk hydraulic conductivity resulting in minimal groundwater discharge to sustain the baseflow of Little Turkey Creek. The Little Turkey Creek valley forms the major conduit for groundwater flow exiting from the upper part of watershed underlain by granite. This conclusion has significant implications with respect to mine planning to minimize projected impacts to the hydrologic system and preserve this recharge component to downgradient Denver Basin sedimentary deposits.

By T. Niedoba

Coal as an energetic raw material is characterized by many features that determine its quality. The data concerning coal are usually treated as independent values, despite the fact that this kind of approach is not always appropriate. In the paper the dependencies between sulfur contents and volatile components in coal and particle size and density were analyzed. The method of ordinary kriging is applied to experimental data to describe this relationship; this method can be used for particles of any size and density. An example of the application of this technique is presented for energetic coal Type 31, originating from one of the Polish hard coal mines in Upper Silesia. Results from ordinary kriging are in good agreement with experimental results. Similar analyses can be performed for other properties of coal material, such as ash content, Roga number, and moisture. On the basis of the data obtained by ordinary kriging, a more comprehensive multidimensional model is described, which can characterize certain deposits or strata from which the analyzed materials originate. This is superior to basing the model only on experimental data, which often is limited by size of the sample. The results obtained by ordinary kriging applied to various types of coal would allow more precise analysis of individual properties of the studied materials and increase the ability to determine significant differences between them. This method can be also applied to other types of mineral raw materials, such as copper ore.

Aug 1, 2013

By R. P. King, M. K. McCarter, K. S. Free

Mine plans typically consider the profits and costs associated with extracting and processing minerals into marketable products. Interrelationships between mine and mill costs are often overlooked during the process of mine plan optimization. A simple and quick method for predicting milling costs for a given block would improve the planning process, especially if the procedure could be incorporated as part of routine ore grade analysis of drill core or cuttings. Incorporating milling costs as part of the mine planning process could improve overall optimization of the mine/mill combination. A method developed by the Utah Comminution Center (UCC) at the University of Utah provides a possible answer to the need for quick and reliable grinding cost estimation (King et al., 1996). Using results from single-particle impact tests, a work index, called the Utah Load Cell Work Index (ULCWI), is calculated. The potential for routine use of the new method is explored by comparing ULCWI values with corresponding Bond Work Index (BWI) values for eight mineral materials (Free, 2000).

Jan 1, 2004

By Dave Bulled

"This paper describes the design of a molybdenite flotation circuit using FLEET technology applied to kinetics data produced from laboratory flotation testing and distributed across the blocks of a mine plan using a geostatistical approach. The geostatistics assigned the statistical error that arises from having a limited amount of sample testing data to the kinetics estimates of each block of ore in the mine plan. The final design then included a quantification of risk based on the accuracy of the block flotation kinetics and model fitting. The design made reference to the extensive technical reports describing earlier metallurgical test work including some pilot plant work over thirty years ago.The testing involved conducting MinnovEX Flotation Tests (MFT) to determine the rougher flotation kinetics at the specified reagent conditions and rougher-cleaner tests to determine the change in kinetics resulting from regrind. These flotation kinetics were used within FLEET simulations to create a full-scale flowsheet and plant design including recommended equipment sizes and the forecast of operating results. Measurement of detailed flotation kinetics for a wide range of samples allowed the effect of size of grind and efficiency of classification (i.e. width of size distribution) to be predicted for the whole ore body.INTRODUCTIONAdanac Moly Corp. proposed to develop a 20,000 ton per day mill to produce high quality molybdenite concentrate from its Ruby Creek resource in north-western British Columbia. It is a relatively clean low grade porphyry-monzonite occurrence containing minimal quantities of other sulphides such as chalcopyrite, pyrite, sphalerite and galena. Molybdenite occurs mainly as coarse flakes with lesser amounts of finer sized values. An optimum plant design was required to can achieve the predicted operating results, at a known level of risk, while treating the variability inherent in the ore body."

Jan 1, 2007

By A. Koning

Pressure hydrometallurgy operations require vessels to be lined with an impermeable membrane for corrosion protection and one or more courses of refractory or ceramic brick. Examples of unit operations that utilize composite lining systems include pressure oxidation autoclaves, sulphide precipitation autoclaves, chloride leach reactors, flash vessels, cyclone separators, and direct contact condensers (heater vessels and quench vessels). The refractory lining must satisfy multiple requirements: it must thermally insulate the membrane from process fluid, be structurally stable, provide erosion resistance, be chemically compatible with process fluid, and provide an economic service life. New hydrometallurgical processes are pushing the pressure, and temperature with each new generation of plants. A fundamental understanding of all factors affecting the mechanical stability of the lining system is essential as lining designs move further away from the industry?s experience base. The method of designing a refractory lined vessel is examined taking into account the impact of irreversible chemical swell, operating factors, design factors, and installation factors. The effect of geometry and incorporating additional degrees of freedom to the analysis is explored using two-dimensional and three-dimensional finite element analysis (FEA). The effect of these additional degrees of freedom on the results of the one-dimensional model are discussed. Keywords refractory lining design,autoclave, finite element analysis.

Aug 1, 2013

By James A. Voigt

The efficient separation of metal species from aqueous streams by precipitation techniques requires 'a fundamental understanding of the various processes that occur during precipitation. These processes include particle nucleation, particle growth by solute deposition, agglomerate formation, and agglomerate break-up. The application of the population balance approach has been used to develop a kinetic model that accounts for these competing kinetic processes. The usefulness of the model is illustrated through its application to the precipitation of yttrium hydroxynitrate, YHN. The kinetic parameters calculated from the model equations and system-specific solution chemistry are used to describe several aspects of the effect of pH on the precipitation of the YHN. Implications with respect to the simultaneous precipitation of more than one cation type are also discussed through use of example systems: The effects of solution chemistry, precipitator design, and solvent choice are considered.

Jan 1, 1996

By D. Ksinsik, R. Boisvert, D. Leblanc

Casting, cooling and crushing/sieving of ferroalloys has followed a well-established pattern in the whole ferroalloys industry for many years. Usually liquid metal or alloys are cast into flat open moulds of various shapes and forms, and after solidification the product is removed from such mould to further cool down to a temperature where subsequent handling steps are feasible. Common to all mechanical product fractioning is the generation of dust and fine size material with lower product value. For almost 10 years, Bécancour Silicon has investigated alternative roads to improve technology and/or reduce or solve problems related to those disadvantages. Since 1995 Bécancour Silicon operates a special silicon granulation plant targeted to product for the chemical treatment/conversion of silicon for silicones production. Prior to the development of the granulation process, various systems had been evaluated, among others the vibrating casting bed, now in operation elsewhere but judged inappropriate because of the tapping volumes to be handled at Bécancour Silicon and other disadvantages. After evaluation of all aspects of heat transfer, radiation, and conductivity in relation to transfer media and within the product, a novel system was designed and built.

Jan 1, 2004

By R Baumgartner

The Canahuire deposit is a recently discovered Au-Cu-Ag epithermal deposit in Southern Peru. A geometallurgy program is a key study element of the project Feasibility study. Metallurgical, mineralogical, and comminution studies have been completed over a suite of samples, spatially distributed among the various geological/ore domains. The early stage of Canahuire presents challenges as there is a lack of metallurgical information to guide geometallurgical sampling, in contrast with an established deposit at a more advanced stage of development or mining. Nevertheless, the available information will assist in the development of geometallurgical domains for Canahuire in order to ensure that future metallurgical, mineralogical, and comminution test work is representative of the deposit variability. This supplementary knowledge will be able to predict important metallurgical parameters which will be incorporated into a geometallurgical model to spatial predict material types, metallurgical recovery and through put. The information obtained will be a valuable addition to the future mine plan, influencing process design, engineering design, plant operation, operating and capital costs, and ultimately will reduce project development risk.

Sep 5, 2011

By Paul B. Crawford, Melvin B. Burton

A procedure is given which describes how the gelatin model may be-used to study the effect of mobility ratio on areas swept before and after breakthrough in fluid injection programs. Differences in mobility ratio are achieved through the proper selection of electrolytes for the invading and displaced fluids. The progress of the front is followed visually and photographed or traced onto plates (it desirrd positions before and after breakthrough. Example applications to standard flooding pattrrrls, vertically and horizontally fractured reservoirs and the in-situ combustion recovery process ore presentrtl. INTRODUCTION In water flooding, gas cycling and other fluid injection programs, the sweep efficiencies and swept areas after breakthrough are known to depend on the mobility ratio. Previous investigators have described the application of the X-ray technique, stepwise use of the poten-tiometric model and numerical procedures for studying these problems.1,3,4,6 Others have described the application of the electrolytic and gelatin models for studying sweep efficiencies at a mobility ratio near one.2,5,7,8,9 It is a purpose of this paper to describe a procedure for using the gelatin model to study swept areas at mobility ratios other than one. PROCEDURE The technique developed for gelatin model studies is composed of four phases: the construction of the model, the selection and preparation of electrolytes, the running procedure, and the recording of the swept areas. Each phase is discussed independently in order that the over-all procedure will not be confused. Construction of the Model Since some of the advantages of the gelatin model are its economy, and speed, it is desirable to have as small a model as is possihle without creating error through the inability to follow visually the progress of the colored front. For this work, it was found that a distance of 4 to 6 cm between salt bridges is convenient to use. Since the size is relatively small, it follows that the gelatin layer must be thin. For this study, 1/8 in. was used as the gelatin thickness in each case. The model was constructed on a flat 1/2-in. plastic (Lucite) base with boundaries constructed from 1/8-in. plastic strips. The well pattern to be studied was outlined with the 1/8-in. plastic strips on the base with narrow apertures (- - 2 mm) in the boundary to represent the wells. Behind each well opening, a rectangular area of some 8 to 12 sq cm was outlined by additional plastic strips. The plastic strips were fastened to the base by any suitable non-conducting cement so that the boundary system was liquid tight. The electrodes were constructed from sheet copper in a fashion that would allow easy removal. In this work, it was found that by simply forming a large U-shaped clip from a strip of the copper that would slip over the boundary was satisfactory and easily removed. The electrodes should be as wide as one of the sides of the rectangular area behind the well opening. If a fractured pattern is studied, fractures inside the well pattern may be represented by strips of copper of the desired shape mounted in some easily removable fashion. The reason that apertures (or salt bridges) were used for wells instead of metallic electrodes is that the plating of the electroactive ion at the cathode and the introduction of an electroactive ion at the anode has a detrimental effect on the swept area outline if these operations \rere permitted to be carried on within the well pattern itself. The anode may be used within the well pattern

Jan 1, 1957

By S. J. McCarroll

Fig. 1—The belt shown at right carries filter cake to mixing station over calciner. Crude ore conveyors appear in right background. THE Three Kids mine, some six miles east of Henderson, Nev., is in a typical southwest desert area, with high dry summer heat and cool to cold winter seasons. The manganese deposit was located during World War I.' During this period 15,000 to 20,000 tons of ore assaying up to 41 pct manganese were shipped. Interest in the deposit was not revived until the middle thirties, when experiments on the ore were initiated. Test work indicated possible recovery of only 70 pct by flotation, but in 1941 additional work was done at the Boulder City pilot plant of the U. S. Bureau of Mines and also by M. A. Hanna Co. As a result, the Manganese Ore Co. was formed and a plant utilizing the SO2 process was constructed. Numerous operation difficulties ensued, and the plant. was closed when the manganese situation in the country eased. In 1949 Hewitt S. West initiated negotiations to acquire the plant. In 1951 Manganese, Inc., was formed and contract entered into with the General Services Administration to supply 27 million units of metallurgical grade manganese in the form of nodules to the national stockpile. A second contract was made to upgrade 285,000 tons of stockpile ore. Test work was undertaken by the Southwestern Engineering Co. and likewise by the Boulder City pilot plant at the U. S. Bureau of Mines. Results obtained indicated the commercial feasibility of the flotation process. Construction of the plant, which is shown in Figs. 1 and 2, was started in June 1951, and operations on a break-in basis began in September 1952. Apart from the usual starting difficulties two major disasters caused serious setbacks, one a kiln failure in February 1953, and the other a fire that destroyed the flotation building in June of the same year. The nodulizing section of the plant resumed operation in November, and the flotation section in January 1954. The ore minerals are chiefly wad,* with minor amounts of psilomelane, and occur in sedimentary beds of volcanic tuff. The ore is overlain with beds of gypsum which outcrop or may be covered with surface gravel. Intermediate beds of red and white tuff occur frequently with lenses of red and green jasper and stringers of gypsum and calcite. Small amounts of iron are present; lead content averages about 1.0 pct and minute amounts of copper and zinc are found. Barite, celestite, and bentonite are present. Since these are made up of minute asicular crystals, moisture content is very high, averaging about 18 pct. Ore reserves have been estimated at 3 million tons averaging 18 pct Mn2 and up to 5 million tons after grade is dropped to 10 pct Mn. A good part of the orebody was stripped of overburden by the previous operating company . Approximately 50 pct of the ore, representing more than 60 pct of the manganese, can be mined by open-cut methods. A system for underground min- . ing has not yet been decided on. Open-cut mining with benches of 20 ft has proved satisfactory. Although the ore is soft and appears dry and dusty it has a certain resilience, probably due to the porosity and moisture which makes drilling and fragmentation difficult. Wagon drills have been abandoned in favor of the Joy 225-A rotary drill which will put down a 43/4 -in. hole at the rate of 2 ft per min. Holes are spaced in a pattern with 8 to 9-ft centers. Forty percent powder has been used, but better breaking to 2-ft size is obtained with low velocity bag powder of 30 pct strength. Loading is done with one 21/2-yd shovel, and cleanup follows with one D-7 bulldozer. The ore is hauled with Euclid trucks about 1000 ft from the pit to a blending pile, where the daily mine production is spread in layers by bulldozing until approximately one month's mill feed is accumulated. A new pile is then started and mill feed is drawn from the first pile by one 13/4-yd shovel and Euclid trucks, with a haul of approximately 500 ft. Mining is performed by an independent contractor with engineering and supervision by the company staff. Early test work indicated that the manganese could be floated with soap, a wetting agent, and fuel oil to give a recovery of better than 75 pct with a grade of 43 pct Mn. The concentrate when nodulized with coke would upgrade to 46 pct Mn or over, and the lead volatilized to 0.6 pct residual.

Jan 1, 1955

By O. C. Gaspar

The mineralogical and textural characteristics of the volcanogenic massive sulphide ores from the Aljustrel and Neves-Corvo deposits have been studied by ore microscopy techniques since 1977. Several ore types have been recognized, and the ore paragenesis, ore textures, and behaviours of different ore types during grinding and concentration processes, have been determined. An ore classification was established for use in metallogenetic studies, ore reserve calculations, selectivity during mining, and control of the ore beneficiation processes. In addition, an empirical method was developed for supplying, on time, the qualitative and semi-quantitative information needed for processing the Aljustrel ores and for optimizing the Neves-. Corvo copper and tin concentrators.

Jan 1, 1991

By P. Hr?enjak

Two groups of methods are usually used in design procedures of underground excavation of dimension stone: the analytical and numerical methods of analysis. In all of these methods the in situ rock mass strength represents the main problem. This is due to massive rocks in dimension stone deposits, consisting of large blocks of rock separated with particular discontinuities, for which the Hoek-Brown empirical criterion, developed for jointed rock masses, cannot be realistically used to estimate rock mass strength, especially for a particular block of rock mass or a particular pillar. On the basis of the regular underground excavation process of dimension stone by separating blocks with the flat jack application, we developed the in situ flexural strength testing method. We carried out numerical analyses and evaluation of uncertainty of measurement in order to validate the in situ flexural strength testing method. On the basis of very good validation results, as well as results of the in situ flexural strength testing of exploitable layers on the ?Kanfanar? quarry, we introduced a new coefficient of reduction, which can be used for correction of other strength parameters determined by laboratory testing for obtaining a realistic value of rock mass strength.

Aug 1, 2013

By C. Geier

Previous mine incidents show weaknesses in mine rescue preparedness from poor training in decision making, leadership and incident command center (ICC) protocols. Computer simulations offer a larger range of training opportunities for mine rescue teams focusing on exploration and communications. The mine rescue simulator developed by the Colorado School of Mines and Rite Solutions Inc. utilizes four computers for the instructor and team, with the instructor monitoring the team?s progress. As the team explores, it relays information back to the Fresh Air Base, which then reports to the ICC. This forces a three-step communication procedure, enhancing the team?s overall communication skills and developing ICC protocols. The simulator is decision-based, demanding team decisions be made quickly. Upon completion, teams commented positively. Generally, participants said that the simulator is useful for learning how to communicate and make decisions during mine rescue emergencies. This mine rescue simulator improves team training, providing effective communications practice with an easy setup and no production interruption.

Feb 1, 2014

By L. Gutierrez, R. Yepsen, F. Alarcón

Chile is the world's largest copper producer which is mostly in the form of sulfides for which froth flotation is the most efficient concentration process. As a result a concentrate that contains high concentrations of copper sulfides such as chalcopyrite, chalcocite and enargite is obtained. In the last decades processing of ores containing high concentrations of enargite (Cu3AsS4) has continuously increased in Chile, which is related to the fact that ore deposits nawadays are more heterogeneous and complex. Enargite is a mineral that contains arsenic and its presence in the copper concentrates implies severe penalties. In addition, the shortage of fresh water has driven the search for new alternative sources of water, among which seawater has proved to be one of the most attractive. The objective of this research is to study the behavior of the enargite in the process of flotation using seawater, and at the same time to compare its behavior with the results obtained using conventional water. The study was carried thorugh micro-flotation tests using pure samples of enargite, at pH values ranging from 4 to 11, both in fresh and seawater. PAX and MIBC were used as collector and frother respectively. Micro-flotation tests were also done at different redox potential conditions so that the effect of the surface oxidation of enargite was evaluated in seawater. The results indicate that the recovery of copper from enargite is reduced in seawater compared to fresh water, in particular at the pH values close to those of the formation of the first hydroxy complexes of Mg and Ca. In general, the experimental data indicate that the floatability of enargite is strongly affected when seawater is used, in particular at oxidizing conditions. These results suggest that Mg2+ and Ca2+ ions contained in seawater interact with the surface of enargite forming hydrophilic species.

Jan 1, 2018

By E. P. Polushkin, Henry L. Shuldener

This paper describes the results of microscopic examination of a series of brass pipes removed from apartment and office buildings in New York City, adjacent localities on Long Island, and Philadelphia. They were selected as typical of approximately four hundred pipe specimens obtained over a period of five years during an investigation of corrosion in hot-water installations. A part of the investigation is reported in this paper and includes a brief history of the pipes, a description of their inside surface and microstructure, and a study of the effects of corrosion, with particular reference to the structural aspects of local and selective dezincification. Although the bibliography on the corrosion of brass pipes is quite extensive, it refers almost entirely to corrosion in sea water. The authors believe that their examination of this series of pipes, which had been subjected to the corrosive action of fresh water for various lengths of time, may throw some additional light on the problem of corrosion. Pipes Examined The pipes were made by different manufacturers and their sizes range from 3/4 in. to 4 in. nominal inside diameter, the majority being within I to 2 in. They can be divided into two groups according to chemical composition: (I) with a copper content of 60 to 62 per cent and (2) with a copper content of 65 to 68 per cent. The first group (pipes made of Muntz metal) comprises 22 pipes and the second (pipes made of high brass) comprises 18 pipes. The pipes had been in service in various locations in the hot-water systems of the buildings involved. Some were taken from horizontal lines in the basement, some from overhead distributors and some from vertical risers. The distance, in terms of feet of pipe, of the specimens from the hot-water generator was no less than 75 ft. and often IOO to 300 ft. In the majority of cases the water-heating equipment was provided with a regulator to limit the temperature of the hot water supply. The normal range of temperature in pipe systems of this kind is Ioo° to 160°F. Water Supples The average chemical composition of the water supplies carried by the pipes is shown in Table I. In evaluating the corrosiveness of a natural water, four factors are considered of prime importance: namely, hardness, alkalinity, pH and silica content. The waters listed in Table 1 are characterized by relatively low hardness, 10, alkalinity, low pH and low silica content. The waters of lower pH and higher CO2 content are more corrosive. A characteristic of all of these waters is that they do not deposit a protective mineral coating as do waters with high bicarbonate of lime content, which would be reflected

Jan 1, 1945

By D. Beneteau, L. Feldman, D. Milne, A. Hyett, G. Snell

"Behaviour of rebar bolts subjected to combined shear and bending in underground potash mining applications is not well understood. An experimental investigation compared load applied to resin-grouted No. 25 metric rebar to theoretical load, calculated using elastic bending theory. Distributed optical sensing (fibre optic) technology allowed axial strain measurements at 1.25 mm increments along the length of rebar. Experimental procedure, data processing methods, and equipment improvements are needed for field applications of optical sensing technology. Goals were to adopt procedures for instrumenting rebar bolts, conduct tests, and develop data interpretation methods to measure field deformations and loads. ¦ KEYWORDS Fibre optic, Potash mine, Rebar bolts, Transverse load testing RÉSUMÉ On appréhende encore mal le comportement des boulons d’ancrage pour barres d’armature soumis au cisaillement et au cintrage pour un usage dans des mines de potasse souterraines. Une étude expérimentale compare la charge appliquée aux barres d’armature de diamètre n° 25 (25 mm en mesure métrique) enduites de résine époxy à la charge théorique, calculée à l’aide de la théorie de la flexion élastique. La technologie de détection optique distribuée (fibre optique) a permis d’effectuer des mesures de la contrainte axiale à des différentielles de 1,25 mm sur toute la longueur de la barre d’armature. Pour des applications sur le terrain de la technologie de détection optique, il faut envisager une procédure expérimentale, des méthodes de traitement de données et une amélioration de l’équipement. Les objectifs établis consistent à adopter des procédures d’instrumentation des boulons d’ancrage pour barres d’armature, à effectuer des essais et à mettre au point des méthodes d’interprétation des données pour mesurer les déformations et les charges sur le site. ¦ MOTS CLÉS boulons d’ancrage pour barres d’armature, essai par charge transversale, fibre optique, mine de potasseINTRODUCTION Resin grouted rebar bolts are commonly used in potash mines in the province of Saskatchewan, Canada, in areas where shear deformation is observed in the rock, or where potentially unstable ground is present, including locations such as clay seams. Opportunities to observe deformations of rebar, as shown in Figure 1, are rare because it is unusual in underground potash mining to excavate supported ground. In this situation, a block of potash containing a rebar bolt had failed."

Jan 1, 2019

By Archer E., Wheeler

Producing copper companies were active during 1941 owing to the national defense program the United States and the requirements of the friendly belligerent nation. This activity extended to the American owned properties in South America, the major part of whose product was taken by the Metals Reserve Co., a U.S. Government agency. Anaconda Copper Mining Co. is building a new converter plant at Anaconda, with four units of the Peirce-Smith type. The addition is being built adjacent to the reverberatory plant so as to avoid the necessity of hauling matte and slag. It is expected to be completed this year.

Jan 1, 1942