Search Documents

By H A. Myburgh

The beneficiation of heavy metal oxides, such as iron ore, is usually performed with heavy medium separation in cyclones, static baths and lately with Larcodems. Atomized ferrosilicon is most suitable as a heavy medium at densities above 3600 kg/m3 whereas a mixture of milled and atomized ferrosilicon is suitable at densities below 3600 kg/m3. When operating a beneficiation plant at densities higher than 3600 kg/m3 the quality of the ferrosilicon particles is an important factor that influences the control of the beneficiation process. Therefore, it is important to know how the rheology would be affected by the ferrosilicon quality as it also influences the control of the process at these elevated densities. Background The Kumba Resources Sishen Iron Ore Mine in South Africa produces 26.5 Mt iron ore per annum from its beneficiation plant. The ore body consists mainly of laminated and massive type hematite ore that is crushed down to ?90mm before being beneficiated by means of a combination of Wemco drums, Larcodem and dense medium cyclone separators. The need for higher densities When the percentage of high-density gangue2 is higher than normal in the run-of-mine (ROM), a higher separation density is necessary to produce a product to specification. Certain ore types of this quality in the Sishen reserves require a separating density higher than 4000 kg/m3, whereas densities would normally average 3600 kg/m3 when beneficiating ores of normal high-density gangue content. Sink and float tests conducted on the ROM material at Sishen revealed some interesting characteristics. In the waste fraction, (density < 3600 kg/m3) it was found that the %Fe was <21% (Fig. 1). Similarly, for the product fraction (density >3000 kg/m3), the percentage Fe varied between 35% and 67.2%. The bulk of the material (88%) actually had a density greater than 4000 kg/m3 and a Fe content that varied between 63% and 67.2%. At a density interval of 3600 to 4000 kg/m3, the Fe content varied from 37% to 60% with an average of 45%.

Jan 1, 2006

By Mark R. Lamb

THE various methods of treating pulp in air-agitation tanks offer problems for experiment and study which are fascinating as well as practical. The usual method heretofore has been to fill each tank in turn, agitate the mixture the required period and then discharge the treated pulp into a storage-tank, from which it. is drawn to the filter as required. A later method is to run the pulp from the tube-mill, classifier, thickener, or settler into the first of a set of tanks, and thence continuously or in series through the remaining tanks, finally drawing off the pulp to a continuous filter, or to a pulp-storage tank if the filter is of the intermittent type. It is this method which I propose to discuss here in a preliminary way, with the idea of going exhaustively into the examination of the results of a series of experiments in a later paper. It may be of interest to note that the design of a cyanide-plant has recently been completed in which the estimated cost of the agitation-tanks, storage-tanks, and pumps was 30 per cent higher for the charge-agitation arrangement than for the series plan. The first question in studying the series method is, "What is the actual period of treatment undergone by the pulp?? One first supposes that by chance some of the pulp may get through with little or no treatment, while other portions may stay in the tanks a needlessly long period. The former is not probable or even possible, and the latter is, practically, true to only a limited extent. The greater the number of tanks the greater is the percentage of chance that all the pulp will be treated equally. Without going into the mathematical analysis of the problem (which is of little value, since it is based on problematical premises), its important terms may be clearly grasped by thinking of, or " visualizing," the conditions when,

Jan 1, 1910

By H. K. Work

The Bessemer process is one of the most interesting methods of making steel. At one time it was by far the most important. In recent years, however, it has steadily lost ground to the open-hearth process. The forces working against this method of stccl-making are partly economic and partly metallurgical.1 In this paper, dealing as it does with the control of the process, the metallurgical factors alone will be considered, although it is obvious that economic factors must play a part in determining the ultimate status of the Bessemer process. This discussion has been limited in another respect—it deals primarily with the acid Bessemer process in bottom-blown converters, although much of the information is applicable to basic and side-blown converters. The fact that open-hearth steel has superseded Ressemer steel to a large extent has tended to create an impression that Bessemer steel is inferior. As a matter of fact, Bessemer steel is actually superior to open-hearth for many applications.2 There are, however, definite metallurgical limitations to the use of Bessemer steel, resulting largely from two factors: (1) the physical properties conferred by nitrogen and phosphorus, and (2) the variability from blow to blow. These, of course, are not entirely independent, since some of the variability covered in the second item is undoubtedly due to nitrogen. But the variability is also caused by other factors. One of these is the relatively small size of the Bessemer heats. Because of this, a given shipment of Bessemer steel is more likely than a shipment of open-hearth steel to contain the product of several heats, each with its own distinctive and slightly different characteristics. Added to this is the fact that the refining of Bessemer steel proceeds so rapidly that the timing of the end point is limited to a matter of seconds, whereas the finishing period in the open hearth extends over a period of one or two hours and the timing of the end point may vary by several minutes without seriously affecting the product. There is no doubt that this has contributed to the variability of Bessemer steel and has led to the use of open-hearth steel in many optional applications. That Bessemer steel may vary is not necessarily objectionable, and it may even prove an advantage, providing a precise control is available to secure the desired qualities for any specific application. With this in mind, a comprehensive research program was undertaken, one phase of which was directed toward securing more accurate control of the blow. The results have been encouraging, and it is the purpose of this paper to describe a method in which modern scientific instruments, based on photocells, are currently being employed to assist the blower. The Control Problem In this day of scientific control of technical processes, where the operating

Jan 1, 1941

By H. K. Work

The Bessemer process is one of the most interesting methods of making steel. At one time it was by far the most important. In recent years, however, it has steadily lost ground to the open-hearth process. The forces working against this method of stccl-making are partly economic and partly metallurgical.1 In this paper, dealing as it does with the control of the process, the metallurgical factors alone will be considered, although it is obvious that economic factors must play a part in determining the ultimate status of the Bessemer process. This discussion has been limited in another respect—it deals primarily with the acid Bessemer process in bottom-blown converters, although much of the information is applicable to basic and side-blown converters. The fact that open-hearth steel has superseded Ressemer steel to a large extent has tended to create an impression that Bessemer steel is inferior. As a matter of fact, Bessemer steel is actually superior to open-hearth for many applications.2 There are, however, definite metallurgical limitations to the use of Bessemer steel, resulting largely from two factors: (1) the physical properties conferred by nitrogen and phosphorus, and (2) the variability from blow to blow. These, of course, are not entirely independent, since some of the variability covered in the second item is undoubtedly due to nitrogen. But the variability is also caused by other factors. One of these is the relatively small size of the Bessemer heats. Because of this, a given shipment of Bessemer steel is more likely than a shipment of open-hearth steel to contain the product of several heats, each with its own distinctive and slightly different characteristics. Added to this is the fact that the refining of Bessemer steel proceeds so rapidly that the timing of the end point is limited to a matter of seconds, whereas the finishing period in the open hearth extends over a period of one or two hours and the timing of the end point may vary by several minutes without seriously affecting the product. There is no doubt that this has contributed to the variability of Bessemer steel and has led to the use of open-hearth steel in many optional applications. That Bessemer steel may vary is not necessarily objectionable, and it may even prove an advantage, providing a precise control is available to secure the desired qualities for any specific application. With this in mind, a comprehensive research program was undertaken, one phase of which was directed toward securing more accurate control of the blow. The results have been encouraging, and it is the purpose of this paper to describe a method in which modern scientific instruments, based on photocells, are currently being employed to assist the blower. The Control Problem In this day of scientific control of technical processes, where the operating

Jan 1, 1941

By J. A. Eisele

The Federal Bureau of Mines is engaged in a continuing program on the recovery of alumina from domestic source materials. Of the six processes being studied, current efforts focus on HCl leach of clays. A key step in the HCI process is the removal of iron from the aluminum chloride leach liquor. This was accomplished .by solvent extracting the iron with a tertiary amine in kerosine to which decanol was added as a phase modifier. In a mixer-settler operation, iron in the raffinate was reduced to <10 ppm in two extraction stages from a feed containing 1.4 gil Fe. Iron was stripped from the organic phase in three stages with dilute HCl.

Jan 1, 1976

By Yap Chu-Phay

Although chronologically the Sb-Bi system was the first one studied by the writer, the theoretical basis of the equations used in this paper is fully discussed in the writer&apos;s paper on the iron-carbon system,&apos; because he believed that many would be more interested in the iron-carbon alloys. He suggests, therefore, that the reader consult that paper to familiarize himself with the theoretical aspect of the thermodynamic treatment outlined herein. This paper is divided into two parts: Part &apos;I deals with the Sb-Bi system and Part II deals with the lead-rich side of the Sb-Pb system. Although the former system has not much practical interest now, it has great theoretical interest in that it is the one system that for a long time was thought to have (and under specific conditions still has) an anomalous solidus, which no amount of physical investigation could adequately account for. The latter system, of course, is particularly interesting in the lead-rich end. It will be shown that the thermodynamic method is capable of predicting reliably the equilibrium position of the solidus, and thus acts as a check on the experimentally derived solidus. PART I.—THE ANTIMONY-BISMUTII SYSTEM In connection with his studies in thermoelectric phenomena,-the writer was naturally interested in the system Sb-Bi. In consulting the International Critical Tables2 he found the constitutional diagram shown in Fig. 1 (not including Ôtani&apos;s solidus), essentially after Cook,³ who investigated the system carefully by thermal analysis. Note the isothermal crystallization of alloys varying in composition from about 48 per cent, (by weight) to pure Bi. This is anomalous, because, according to the phase rule, in a binary system when only two phases coexist, there is univariant equilibrium; that is, the composition changes with the tempera-

Jan 1, 1931

By D. M. Range

Exxon is reclaiming an 80-hm2 (200¬acre) Wyoming uranium tailings basin in accordance with US Nuclear Regula¬tory Commission (NRC) requirements. The reclamation plan is designed to control the tailings and their radioactive emissions for at least 1000 years. Rigorous modeling and analyses of potential erosion by wind and water were used in planning. The use of riprap was minimized and the need for long¬term reclamation maintenance was eliminated. The resulting design is simi¬lar to regions stable from erosion cre¬ated by nature. The concepts used in the design and implementation have wider reclamation application. Highland history Exxon operated the Highland uranium operations from 1972 until mid-1984. Open pit and underground operations mined the roll front, sandstone ore body. The 2.5 kt/d (3000 stpd) mill employed conventional crushing, grinding, sulfu¬ric acid leach, CCD, SX, precipitation, and drying circuits. The mill produced 10 Mt (11 million st) of tailings. An¬other operator began commercial scale in situ leach operations in 1988. The tailings basin was constructed by deposition of mill tailings in a natural ravine dammed with a 30-m (100-ft) high by 1050-m (3400-ft) long clay core earthen dam built entirely downstream of tailings. Figure 1 shows the layout of the tail¬ings basin in 1984. Tailings were de¬posited along the dam face on the east side of the basin as well as in the west end and along the south edge until the early 1980s. This left a deep water pond in the middle of the basin. The deep pond was largely filled with tailings during the last four years of mill opera¬tions by the construction of two tailings causeways and the operation of a float¬ing tailings line. The pond water volume was mini¬mized by recycling tailings water to the mill and by operating a 32-L/s (500¬gpm) evaporation enhancement spray system during the last few years of mill operations. Regulatory requirements Several conceptual tailings basin rec¬lamation plans were prepared during the mine life. In September 1984, Exxon began preparation of a detailed plan in response to an NRC request. Water, Waste and Land Inc. (WWL) of Fort Collins, CO was selected to help pre¬pare the plan that was submitted to the NRC in December 1984. The design had to meet the require¬ments found in NRC regulations (NRC, 1985). These were based on regulations prepared by the Environmental Protec¬tion Agency (EPA, 1983) at the man¬date of federal law (UMTRA, 1978). The NRC regulations contain strict primary standards and a somewhat more flexible set of secondary standards. The primary standards include requiring that: • radiation from tailings be reduced to background levels; • radon gas emitted by the tailings be reduced to 20 pCi/m2/s from the surface of the reclaimed tailings pile; • tailings not be dispersed into the environment; and • these conditions endure without routine maintenance for at least 200 years and for 1000 years to the extent reasonably attainable. The lengthy time requirements pre¬sented a large engineering challenge. Radon is a radioactive, chemically inert gas with a 3.8 day half-life. It is released from uranium tailings by the radioactive decay of radium, which, in turn, is a radioactive decay product of uranium. Radon emissions from ura¬nium tailings can be controlled with an earthen cover thick enough that the radon gas decays to its solid, short-lived radio¬active daughters before the radon dif¬fuses through the cover material into the air.

Jan 1, 1989

By J. M. Goris

Cable bolt supports are becoming an important ground control technique in underground mines in the United States and Canada. They show great versatility and are adaptable for use with many mining techniques, they have high load-carrying capacities, they can be installed in small areas with low roots, and they are cost effective. Investigators in a number of research institutes in North America have conducted studies to assess the material and support properties of cable bolts, evaluate their support capabilities under various mining conditions, and provide design criteria for using cable bolt supports as roof control systems under varying mining conditions. While conducting these studies, personnel have collected important information on the history, application, performance, and economics of these supports. This U.S. Bureau of Mines report documents this information so that ground control personnel unfamiliar with cable bolt supports can gain an understanding and appreciation of their use. A comprehensive bibliography of technical information on cable bolt supports was selected by the authors and is also presented.

Jan 1, 1994

By C Mann, S Swapp

"The mining industry is often challenged with the task of evaluating narrow vein open pit deposits. A realistic mineable solution from optimisation needs to accurately represent mining dilution and the practical limitations of mining equipment. Open pit dilution is driven according to mining method and fleet selection as this dictates the ‘selective mining unit’ (SMU) that can be practicably mined.Common evaluation methods represent dilution by:a mathematical dilution assumption addition of a dilution skin reblocking of the model to an appropriate SMU.This paper will explore an alternative method of applying dilution by adapting an underground stope modelling tool. By considering an SMU as a stope, automatic stope shape creators such as Datamine’s Mineable Shape Optimiser (MSO) can be used to create wireframes for each mining unit over the entire deposit. Using these wireframes, the model can be subblocked and assigned as either ore (inside the wireframe) or waste (outside the wireframe) prior to optimisation.The MSO process considers SMU geometry and a depth specific value-based cut-off. The result is an optimised solution for the deposit based on practical and achievable mining constraints rather than one based on generalised modifying factors.To evaluate the economic impact of the methods above, results have been costed and scheduled and a comparison of operating cash flows made.Citation:Swapp, S and Mann, C, 2016. Optimisation Improvements for Narrow Vein Open Pit Deposits Using Mineable Shape Optimiser, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 50–59 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By Gerald T. Homce

Data from the U.S. Bureau of Labor Statistics show that 89 water well drillers died on the job between 1992 and 2002, and 28 of these deaths were electrocutions (Figure 1). In fact, elec­trical accidents are the leading on-the-job killer of water well drillers. The use of electricity is such an integral part of our lives that we usually take it for granted, but if we don?t understand or choose to ignore the hazards associated with electricity, the results can be deadly. Why is electrical shock so dangerous? If the voltage (of a shock) is sufficient to drive electrical current through your body, just 10 milliamps of cur­rent (1000 milliamps = 1 amp) can cause muscles to contract and prevent you from releasing an energized wire or tool in your grip. As little as 30 milliamps of current can paralyze your breathing, and 75 milli­amps can cause your heart to stop pumping blood (ventricular fibrillation). As a comparison, a small bedroom night-light draws about 30 to 60 milliamps. Other factors influence how severely you?ll be shocked if you touch a live electrical circuit, such as the path electrical current takes through your body and how long it flows, as well as your body weight. How much voltage is needed to drive electrical cur­rent through your body? Not much! Generally, any power source at 50 volts AC or higher is considered dangerous.

Jan 1, 2008

By Andrew B. Allen, Charles W. Robinson, Robert L. Schneider

In April, the US Synthetic Fuels Corp. broke a three-year silence and made its first financial award by approving a $820,750 loan for the First Colony peat-to-methanol project in North Carolina (ME, May, page 403). Peat Methanol Associates (PMA), a partnership between Koppers Co., ETCO Methanol Inc., Transco, Peat Methanol Co., and l. B. Sunderland, broke ground at First Colony last year and plans to begin production in Dec. 1985. Although the award is only a small part of Synthetic Fuels Corp.&apos;s $15-billion budget, it does signal the corporation&apos;s intention to move aggressively ahead. It also is a positive indication that First Colony will be completed and operated successfully. This article describes the methods and equipment that will be used to harvest peat at First Colony, as well as how the peat will be converted to methanol. Introduction Peat deposits found along North Carolina&apos;s coastal plain contain high-quality fuel-grade peat with an average heating value of more than 23.3 MJ/kg (10,000 Btu/lb) (dry), with a low sulfur and ash content. The deposits differ from other US peats in that they contain large, sound Atlantic White Cedar and Cypress logs, stumps, and roots that may extend throughout the full depth of the deposit. A second difference is that these deposits are much more highly decomposed and, in the raw state, have the appearance and feel of a heavy, reddish-brown grease. These factors make it impractical to use standard production equipment so a new line was developed. Also, because of these conditions, techniques were modified to facilitate production. First Colony Farms, located near Creswell, NC, developed and evaluated a milled peat program. Equipment for this production method was designed and built, production rates were established from field operations, drying rates were established, weather data were analyzed, and total operating and capital costs were estimated. The method depends on the sun and wind for drying peat to the desired moisture content, in this case around 40%. Therefore, field preparation is actually the construction of a large solar collector to dry the peat so it can be harvested and stockpiled. It is essential that this collector be properly profiled initially and maintained during production to prevent precipitation from ponding. Initial Field Preparation Initial field preparation includes cleaning existing canals and constructing ditches and water control structures for proper drainage of rainwater run-off, building adequate roads for site access, removing surface vegetation, and profiling and sloping the fields. At First Colony, the 60.7-km2 (15,000-acre) harvesting area was divided into 129.5-hm2 (320-acre) blocks about 1.6 km (1 mile) long and 805 m (0.5 mile) wide. This was accomplished by cleaning main outfall canals with adjacent roads built from canal spoil at 1.6-km (1-mile) intervals. Existing intermediate canals that feed into main outfall canals at 805-m (0.5-mile) intervals also are cleaned. Headland roads are constructed from canal spoil along each side of each intermediate canal. This 129.5-hm2 (320-acre) block is then divided into 32 harvest strips by small V-ditches constructed at 50-m (165-ft) intervals. At the end of the field with the lowest elevation, corrugated steel pipe culverts are installed under the headland road in each V-ditch to control rainwater runoff into intermediate canals. Runoff water from the fields is diverted to a holding pond to prevent any increase in peak water runoff rates and to allow for more uniform drainage rate than experienced to date. After the drainage system is installed, harvest strips are ready for grinding and sloping operations. Surface vegetation, made up of small, waxy-leafed shrubs such as Gallberry, Bayberry, Magnolia, and scattered pond pine, can be effectively ground and incorporated into the upper surface of the peat layer. Here, it will rapidly decompose and have little effect on overall peat quality, thus eliminating the standard practice of pushing the vegetation and upper wood layer into long windrows with bulldozers and hauling this debris from the fields. Incorporating vegetation into the upper surface is known as the initial 102-mm (4-in.) surface vegetation grind and is accomplished by using a modified Bros Rota Mixer. Following this operation, and by using the same unit, a sec¬ond grind with a depth of 200-255 mm (8-10 in.) is made. This reduces the debris to a finer consistency, mixes it with the upper peat layer, and grinds any wood found in the upper 200-255 mm (8-10 in.). After initial grinding operations are completed, the augering or sloping operations can be accomplished with little or no hin-

Jan 7, 1983

By V. K. Kuppusamy, M. Holuszko

"Lamps and lighting products are the most commonly used electrical products around the globe. With the improvement in lamp technologies, lighting products have grown complex and hence require an improved recycling process. The LED lamps consist of various valuable metals such as iron, copper, aluminum, chromium, silver, and gold, as well as non-metals such as glass, plastics, and fibers. In addition, there are also traces of hazardous substances such as lead, arsenic, and mercury. A major step in the recovery process is size reduction, and researchers have suggested that up to 40% of the total valuable material is lost during the shredding and grinding processes. SELFRAG is a high voltage selective fragmentation comminution technology that uses high voltage pulses in a water medium to efficiently separate the metals at a coarser size without generating many fine particles. It has been proposed that during the fragmentation process of electronic waste (e-waste), the metals can be separated without fine grinding. This research considers the applicability of high voltage pulse fragmentation for LED lamps. Eight different types of LED lamps were processed through the SELFRAG unit at varying pulses to study metal liberation. The product obtained was characterized for metal liberation, metal grades, and liberation analysis. The specific energy consumption for this size reduction process was also monitored. INTRODUCTION Lamps and bulbs are the most commonly used electrical products in homes, offices, industrial operations, and streets. According to Energy Star research (2006), an average US household has more than 40 sockets for light bulbs and consumes approximately 2100kWh every year for lighting. The development in lamp technology has pushed the boundary for newer products. The LED lamps have been taking over the market from the incandescent bulbs and compact fluorescent lamps (CFL). According to the US Department of Energy (2012) and myLEDlight.com (2007), LED lamps have several benefits over other lamps. LEDs produce light hemi-spherically, which increases their efficiency in directional light emission. It has higher breakage resistance from vibration or transportation. LED lamps use up to 90% less power than incandescent bulbs thus making them highly energy efficient; They have a longer lifespan, lasting 10 times longer than a CFL and 133 times longer than the traditional incandescent bulb. Because of all the benefits, Smallwood (2014) suggested that the market of LED lamps will grow to $12.2 billion by 2018."

Jan 1, 2018

Jan 1, 1953

By W. C. Holliman

This report on the characteristics of commercial aviation gasolines is one of a series of such reports. It presents compilations of&apos; inspection data furnished on their products by 15 manufacturers of commercial grades of aviation gasoline and special data obtained in Bureau of Mines laboratories on 68 samples of these gasolines. Data are presented for 18 samples of grade 80, 20 of grade 91/98, 21 of grade100/130, and 9 of grade 115/145 aviation fuels. The gasolines are designated January 1948 production, although some of the samples actually were produced at a later date.

Jan 1, 1948

By B. J. Timmons

Depending upon which of two letters describing the theme of the session I chose to honor, the subject choices because either one or three. They were: "Applied Research and Exploration and Discovery" or "Applied Research in Exploration and Discovery." The final choice; to partially ignore both of them. That minor difference in meaning may be appropriate here, inasmuch as very minor research/exploration differences may also have profound impacts on discovery. To further set the stage, I consider myself an Industrial Minerals geologist, and more specifically primarily associated with basic construction materials crushed stone and sand & gravel. My remarks will apply primarily to those materials. Therefore, when the discussion instructions included emphasis on beneficial aspects (to name a few): "drill target definition; elimination of ore potential; ore forming environments; alteration studies, and isotope analysis," problems became apparent. Evidently, and although this was a form letter, the drafters of that letter had no idea what was involved in research for a construction materials source. My task may be great.

Jan 1, 1995

By I. G. Townsend, S. A. Buckley, C. I. House

"SummaryBritish Petroleum plc is developing a new gold recovery process known as coal gold agglomeration (CGA) for the recovery of gold from its ores. Liberated gold grains are recovered with high efficiency by adhering to agglomerates of coal and oil. The process is simple, can recover gold grains down to very fine sizes, avoids the large scale use of cyanide and provides the industry with an important new process option.A technical appraisal of the process has been performed on an extensive range of gold bearing materials. Ore types have been identified from which high gold recoveries can be achieved. A spreadsheet based computer program has been used to estimate the preliminary capital and operating costs of the process. Comparison with established gold production costs shows that the process costs of CGA, on the appropriate ore types, are potentially very attractive, which will enable economic treatment of lower grade ores than is currently possible using conventional cyanidation. Treatment of known placer deposits or gravity concentration plant tailings may be the most rapid means of demonstrating the process at a commercial scale prior to more widespread applications.1. INTRODUCTIONWestern world gold production for the 1980s has shown rapid growth sustained by a demand for gold at a favourable price (Fig. 1). Heap leaching and CIP/CIL operations have been responsible for the major part of new production during the 1970s and 1980s with present overall production costs averaging US$200/oz in Canada, USA and Australia and US$265/oz in South Africa [l]. A great deal of research and process development effort in the 1980s has been towards the treatment of refractory ores. Operating costs for the economic processing of these ore types by currently available routes are around US$300/oz [2]."

Jan 1, 1989

By Jose A. Ruiz

INTRODUCTION For heterogeneous non-catalytic solid-gas reactions carried out in fluidized bed reactors, nominal bed temperature is an average value between gas and solid. For highly exothermic reactions, actual particle temperature can be up to hundred degrees above termocouple temperature, since heat dissipate at slower rate than heat generation during some steps of transformation. These micro instabilities at particle level can displace thermodynamic equilibrium from the desired phase to others. This effect is important when relatively narrow range of phase stability exists, like in sulphation roasting of sulphides, where bed discharge contains, in addition to the desired sulphate others metastable phases such as basic sulphate and ferrite. For example, for copper-iron sulphide concentration roasted below 680°C, no cupric ferrite is formed, as shown by Jakob et al., therefore the separate Kellogg&apos;s stability phase diagrams Cu-S-O represent the roasting (Fig.l). At temperature above this one, like 760°C for example, phase stability changes from CuSO4 to the basic sulphate Cu0•CuSO4. Solid state reaction between Cu0•CuSO4 and Fe203 also occurs to form cupric ferrite, Cu0•Fe2O3, therefore the Cu-Fe-S-O Kellogg&apos;s phase diagram of Fig. 1 (continuous line) represents this condition of roasting. Although both Cu0•CuSO4 and Cu0•Fe2O3 are metastable phases under normal operating conditions of sulphation roasting(1-10% SO2, 1-10% 02 and 680°C, points A and B,Fig. 1) sulphation of these species and particularly ferrite are slow and limited due to diffusional control. This explain why reactors discharge contains several phases: CuSO4, Cu0•CuSO4, CuO•Fe203 plus small amounts of CuS and FeS due to the baclonixed conditions of fluidized bed reactors. The presence of cuprous ferrite due to reducing conditions inside individual particles also occurs, but in very limited extent at the reaction interface, as it is demonstrated by the low soluble iron levels of calcines. On the other hand, the presence of cupric ferrites can be explained only due to the higher temperature achieved by particles, since below 680°C cupric ferrite formation does not take place. [ ] This phenomena also occurs for others non-ferrous metal sulphides concentrates roasted under sulphation conditions, such as 7n, Co and Ni. Therefore the prediction of discharge composition of fluidized beds is not possible based only on kinetics and mechanistics models alone or purely thermodynamical considerations, since all factors should be integrated to describe the overall phenomena. SINGLE PARTICLE TRANSFORMATION Assuming a first order reaction with respect to the gas and zero for solid, such as

Jan 1, 1984

By H. G. Doll

THIS paper discusses a method and apparatus for determining the dip of formations traversed by a drill hole, by means of electrical measurements in the hole. The process consists in recording the Spontaneous Potentials present along three oriented generatrices in the hole. By comparison of the three curves thus obtained, after application of a correction factor to compensate for any deviations of the hole, the dip angle and the dip direction are determined. Excellent accuracy is obtained for dip angles over 10°. Because the method is simple and the apparatus rugged, the measurements are rapid and reliable; consequently, they can be made at all the levels that are of interest at any time after the well has been drilled. Mechanical cores are not needed to evaluate the dips. A convenient, timesaving procedure is to perform the dipmeter survey at the time the electrical log is taken, using for both operations the same cable and truck. Actual examples of results obtained in wells of the Gulf Coast area are given.

Jan 1, 1944

By Leigh J. Wardle

This paper describes a numerical method for calculating the three¬-dimensional stresses and displacements induced by tabular excavations in a rock mass consisting of parallel layers of distinct material properties. The method is based on the superposition of numerical solutions for elementary displacement discontinuities in a parallel layered rock mass. The method can be used to analyse complicated excavation layouts such as those encountered in room-and-pillar or longwall mining. The method can automatically take into account the effect of the earth&apos;s surface. The method offers an economic and efficient solution to stress analysis problems which cannot be adequately modelled using two¬-dimensional methods and for which the expense of three-dimensional finite element or general boundary element analysis cannot be justified.

Jan 1, 1984

By Julia Pflieger, Manfred Russ, Johannes Gediga

This paper shall show an economic feasible approach to implement Greenhouse Gas (GHG) reduction measures into the mining and metallurgy industry. The goal to improve energy consumption is directly linked to the reduction of GHG emissions and therefore directly in correlation with the economic viability. A baseline scenario of the considered reference system and of the respective reference year has to be defined, mapped and analysed. In a second step an analysis of the same operation using available and prospected Best Available Technology (BAT) processes is carried out to generate a basis for a benchmark system. The identified reduction potentials are reported and the GHG emission reductions are put into relation to the investment cost of the new process technologies / process adaption to be implemented. This economic feasibility calculation is necessary to realise a cost efficient GHG reduction roadmap implementation into the company&apos;s business operations. The GHG reduction roadmap is developed using ratios between GHG reduction and investment / operating cost to get an indication for a sequence for implementing carbon emission reductions measures.

Jan 1, 2010