Search Documents

By N. Singh

Merensky Reef is mined extensively within the Bushveld Complex. In previously mined-out areas on the Merensky Reef horizon there are pillars, potholes and remnants that have not been mined. These unmined blocks of ground on the Merensky Reef horizon can influence the mining of the underlying UG2 Reef. The extent of the influence will depend on the size of unmined ground and the middling between the two reef horizons. This paper quantifies the influence of partially extracted Merensky Reef on mining of the UG2 Reef, and aims to provide recommendations for mining strategies, as well as regional and local support to achieve efficient and safe extraction of the UG2 Reef, for various middlings beneath the Merensky Reef horizon. In some cases it was found that relatively shallow UG2 Reef mining could encounter conditions similar to those experienced in deep and ultra-deep mining environments.

Jan 1, 2005

By J. C. Agarwal

Slags produced by modern smelting furnaces contain copper values which are unacceptably high for discard. The electric arc furnace is employed commercially to clean copper from flash furnace slags but the addition of highly oxidized converter slags to an electric furnace has created operational problems. Highly oxidized Noranda Reactor slags have not been processed successfully in a pyrometallurgical process. These slags, which contain large concentrations of copper (5 to 10 per cent), are treated in slag concentrators (controlled cooling, crushing and milling, and flotation) which produce a copper concentrate that must be resmelted. Though commercially operable, it will be shown that the slag concentrator has important process and cost disadvantages as compared to a pyrometallurgical process. In this paper an economic comparison is made between a pyrometallurgical process and the slag concentrator. For the analysis, five hypothetical smelting plants are considered. Each plant treats 1200 tons of copper concentrate per day and produces 109,000 tons of copper annually. The plant configurations used in this study are:

Jan 1, 1976

By J. L. Uhrie

A potentially cost effective technique for the reclamation of heavy metal contaminated soils and sediments involves the technique of froth flotation. Heavy metals sorbed to clays in the soil may be sulfidized by the introduction of sodium sulfide and floated using a dithiophosphate collector. Separations were obtained where up to 78% of all copper ion was removed from the system. Selected samples were floated in a column cell but little advantage was seen.

Jan 1, 1996

By J. -S. Park, H. -S. Jeon

This study has been carried out to develop a relatively simple hydrometallurgical process for recovering nickel as nickel sulfate from the spent nickel-cadmium battery residue in which cadmium was removed by vacuum distillation. This residue is composed of 36 % nickel, 20 % iron, and other metals such as cobalt. First, crushing and selective classification were performed to separate iron to produce a nickel-rich product (over 40 % nickel). This product was dissolved in sulfuric acid to obtain a nickel sulfate solution. During the dissolution, nitric acid and air were added to the system to enhance the iron oxidation reaction rate. The free acid remaining in the dissolved solution was neutralized by adding nickel carbonate. Iron was precipitated as iron hydroxide and removed from the solution. The nickel sulfate solution was then fed to a vacuum evaporator to concentrate the solution by evaporation of water and crystallized at around 45°C to obtain nickel sulfate hexahydrate. A recrystallization process could remove other impurities such as zinc and manganese.

Jan 1, 2000

By H. W. Gillett

Unlike most previous Howe lecturers, I had not the good fortune to be associated with Henry Marion Howe, nor to be directly one of his students. Yet, through his writings, he has been my teacher, as he has of all American metallurgists. Instructive as his writings are—I use the present tense because Howe thought so keenly and reasoned so surely, seeing clearly, as if by intuition, what was hazy to lesser minds, that his writings are still vital—it is not those books and papers, nor even the minds he trained in his classes, that were his most outstanding service. It was the spirit of Howe in his approach to the problems of metallurgy, his broad-mindedness and fairness, his recognition of the need for theories and hypotheses to explain metallurgical phenomena, his willingness to use them as servants, as well as his questioning attitude—his refusal to accept them as masters—that comprise his greatest service. This most thoroughly warrants the honor the Institute pays each year to his memory. These traits I so respect and honor in any man that I glory in this opportunity to do reverence to him in whom they were so notably united. Howe's Discussion of a Creep Problem I have often wished that Howe were still with us to turn his keen insight upon the problems of the use of metals at high temperatures, a field much studied but still very hazy. Indeed, 53 years ago, in a paper1 before this Institute, Howe stated a problem closely allied to some that still perplex metallurgists and engineers dealing with the high-temperature field. Howe was intrigued by a report2 from another old master, Robert Henry Thurston, on the behavior of annealed vs. cold-drawn iron wire, and in order to broaden the foundation for metallurgical generalization, Howe made experiments of his own on copper and silver. In these tests by Thurston and by Howe, the wires were rapidly loaded to determine the

Jan 1, 1939

By S. N. Singh, M. C. Flemings

Results are presented of a detailed study on the combined influences of ingot dendrite am spacing and thermomechanical treatments on the structure and solution kinetics of high --purity cast and worked 7075 alloy. Solution kinetics were found to depend sensitively on ingot dendrite am spacing and on details of therrnomechanical processing, including amount of reduction and extent of&apos; solution treatment before reduction. An approximate analysis is given for rate of solution of nonequilibrium second phase in the cast and worked structres; results of the analysis are compared with experiment. MICROSEGREGATION in high strength aluminum alloys manifests itself as "coring" (composition differences within the primary aluminum-rich phase), and as interdendritic second phase. The mechanism of formation of the microsegregation is understood, and approximate prediction of the amount of second phase is possible for simple binary systems.1,2 When alloy elements or impurities are present in amounts less than their solid solubility at solution temperature, any phases forming from these elements are termed "nonequilibrium" and can be dissolved by appropriate solution treatment. The rate at which the nonequilibrium phases are removed depends sensitively on their spacing (dendrite arm spacing in the cast material, or band spacing in wrought material). When alloy elements or impurities are present in amounts in excess of their solubility at the solution temperature, second phase particles form an "equilibrium" second phase that does not dissolve in heat treatment and may, in fact, coarsen in such treatment. Usual commercial, high strength, wrought aluminum alloys contain nonequilibrium second phases that were not fully dissolved during ingot processing. They also contain equilibrium second phases resulting from impurities present in amounts greater than their solubility. As has been shown by Antes, Lipson, and Rosenthal,3 and will be demonstrated further in a subsequent paper by the authors,4 significant improvements in mechanical properties of high strength alloys can be achieved by reduction or elimination of these second phases. Methods of elimination are 1) to employ high purity materials to minimize amounts of equilibrium second phase, and 2) to employ suitable thermomechanical processing techniques to fully eliminate nonequilibrium second phases. Work reported herein comprises a study of selected thermomechani- cal processing treatments, and of their influence on solution kinetics of wrought high purity 7075 alloy. EXPERIMENTAL PROCEDURE Melting and Casting. The bulk of the work reported was performed on a single ingot of high purity 7075 alloy. The ingot was 4 in. by 4 in. by 8 in. high, uni-directionally solidified following a procedure previously described.5 The mold was heated to 1350°F before pouring the melt. The bottom chill was carbon coated stainless steel. Water was circulated through the chill after the melt was poured. The 7075 alloy was prepared from high purity virgin material (aluminum, zinc, magnesium) and from master alloys (Al-50 pct Cu, A1-15 pct Cr, A1-5 pct Ti). Final measured melt composition (wt pct) was: Zn Mg Cu Cr Ti Fe Si Al 5.70 2.28 1.35 0.18 0.15 <0.002 <0.012 bal Melting was done in a silicon carbide crucible; all tools were coated with zircon wash to minimize iron contamination; degassing was by bubbling chlorine through the melt. che-rmomechanical Treatments. Detailed studies were made on material taken from a location approximately 13 in. from the chill and 51/2 in. from the chill (i.e., from 1 in. thick slices taken between 1 and 2 in. from the chill and between 5 and 6 in. from the chill). Solution treatment was done at 860°F in an air-circulating furnace with a "bottom drop" arrangement to achieve minimum delay time between solution treatment and quench. Samples solution treated in this way were 2 in. by 2 in. by 1 in. Temperature of the quench water was approximately 10°C. Mechanical reduction was by cold rolling. Samples 11/2 and 51/2 in. from the chill were treated for 12 and 24 hr, respectively, before cold rolling. Reduction by cold rolling was then 4/1, 16/1, and 35/1. In each case, several intermediate anneals (1/2 hr at 860°F) were used to permit reaching the final thickness without cracking; two such anneals were used for the 4/1 reduction, five for 16/1, and six for 35/1. After working, materials were again solution treated for various lengths of time from 0 to 48 hr and quenched in water. Structural Measurements. Secondary dendrite arm spacings were measured using procedures previously described.&apos; For each measurement reported, five photomicrographs were first made at X75. Measurements were made of dendrite arm spacings in at least 20 different grains (grain structure was equiaxed). Grain size measurements were made by running a number of random traverses across photomicrographs of the samples and obtaining the mean lineal intercept. Measurement of the volume percent of second phase and porosity was done by quantitative metallography. A two-dimensional systematic point count was used

Jan 1, 1970

By A. W. Deurbrouck

This report describes the preparation characteristics of the significant coalbeds from which samples could be obtained in Webster County, W. Va. In 1964, approximately 825,000 tons of coal was produced in the county, of which 732,000 tons was mechanically cleaned in three preparation plants. The Sewell coal bed accounted for 94 percent of the coal produced. Twelve samples were collected from five coalbeds. Four of the samples would require upgrading to meet metallurgical requirements; two others of just over 8.0 percent ash would require some upgrading. In general the coalbed samples collected in the county were of medium-sulfur and medium-to low-ash content as received or after removal of the sink 1.58-specific-gravity material.

Jan 1, 1966

By Alessandro Navarra, Amir Arash Rafiei, Kristian Waters

Mathematical programming (MP) is fundamental to systems engineering and operations management, but has not been widely adopted by mineral processors. The current paper presents an interdisciplinary approach, using MP to incorporate basic notions of mass balancing into an optimization framework. The optimization is typically related to economic profitability. Two- and three-product formulas are extended to give formal descriptions of alternate modes of operation, and a global representation of the concentrator. At this global level, the framework may assist plant managers to make tactical decisions based on incoming feed data. The MP framework is demonstrated through sample calculations describing a lead-zinc concentrator.

Jan 1, 2015

By C. A. Rowland

Autogenous grinding, defined as grinding with like material, while quite an old art has recently been revitalized. Two phases of autogenous grinding, primary and secondary, have been the subject of recent papers, technical articles and discussions. The purpose of this paper is to discuss a third phase of autogenous grinding - Intermediate Autogenous Grinding - comparing it to and indicating advantages over the other two phases. Autogenous grinding can also be called ?Rock grinding?1; that is, grinding using ore or rock from the same deposit as the mill feed as grinding media contrasted with using as grinding media steel rods, steel or ironballs, natural or manufactured iron, free pebbles, or other shapes and materials foreign to the mill feed.

Jan 1, 1964

By L. C. IlsLey

"The use of trailing cables on cutting machines, loading machines, and similar electrically operated apparatus is recognized as a necessary adjunct to the economical operation of such units. On the other hand, such cables because of their liability to failure from being run over by cars, locomotives, and other track-operated equipment offer one of the greatest hazards - indeed, probably the worst hazard - met with in the operation and maintenance of permissible equipment. Therefore, the Bureau of Mines is seeking ways of making the use of trailing cables less hazardous.Recently the bureau conducted an extensive investigation of both concentric and duplex rubber-sheathed trailing cables at the Pittsburgh Experiment Station. The results of this investigation were published in two reports.3 4In a larger part of portable motor operations in mines a double-conductor cable can be used. The investigation already mentioned indicated that it is feasible to construct a 2-conductor cable that will stand considerable abuse, such as being run over by loaded cars or light-weight locomotives without producing dangerous arcing in the cable either from grounds or short circuits. There are conditions where more than two conductors are necessary, and in such instances it will probably be necessary to use a cable less resistant to this kind of abuse.Schedule 2C, covering the tests of electric motored equipment, was approved February, 1930. This schedule provides for performance tests on trailing cables as follows;Trailing Cable Performance: The following performance test, optional with the manufacturer, is established for determining the suitability of trailing cables for use on permissible equipment. Trailing cables that pass this test will be especially recommended for this service.The cable will be placed across the two rails of a track and a 4-wheeled 7-ton car will be run over it 50 times. The speed of the car shall be approximately 3-1/2 miles per hour and potential shall be applied to the cable during tests. The cable will be shifted in position after each passage of the car thus giving 100 places over which two wheels have passed. To warrant special recommendation of the Bureau, a cable must neither become short-circuited nor grounded either to the rails or wheels in more than 10 per cent of the 100 places.The Bureau of Mines is prepared to conduct tests as outlined in the foregoing paragraphs to determine the suitability of trailing cables for use on permissible equipment. Application for such tests should be made to the Director, Bureau of Mines, Washington, D. C. Each application should be accompanied by a check for $25.00, made payable to the Treasurer of the United States, to cover the expense of conducting the test on a given size and make of cable."

Apr 1, 1930

By Robert C. Speck

The U.S. coal industry has long utilized the pillar-extraction mining technique as a method for maximizing coal recovery. Like longwall mining, it causes large-scale movements that progressively propagate from mine-level to the ground surface and may affect the groundwater regime, surface drainage and surface structures. The U.S. Department of Energy, in an effort to foster in- creased use of total extraction mining techniques, has recognized the need for a better understanding of these movements that will lead to a greater compatibility between coal mining and present and future land use. As part of that goal, GAI Consultants, Inc. is currently in- stalling instrumentation to monitor the ground movements associated with pillar extraction mining at Kitt Energy Corporation&apos;s No. 1 mine in northern West Virginia.

Jan 1, 1982

By E. A. Devuyst, G. Robbins

A unique process for removing cyanide and base metal complexes from industrial waste streams was patented by G.J. Borberly et al. (1984). The process uses SO2 (liquid or gas, or solutions of sulfite salts, or from burning elemental sulfur), plus air that is dispersed in the effluent using a well agitated vessel. Acid produced in the oxidation reactions is neutralized with lime at a controlled pH generally in the range 7 to 10. The reaction requires the presence of soluble copper as a catalyst which can be supplemented by copper sulfate if necessary. The process can be applied to the detoxification of gold and silver mining waste streams, such as carbon-in-pulp (CIP) tailing pulps, barren solution bleeds, pond waters and heap leach rinse solutions and also to plating shops wastewaters. The SO.jAir process has substantial advantages over two of the main alternative methods of cyanide destruction, namely alkaline chlorination and hydrogen peroxide. Alkaline chlorination is highly penalized in terms of reagent consumption. Chlorine is a strong oxidant reacting with species other than cyanide present in the effluent such as thiocyanate and sulfides. Furthermore alkaline chlorination is an incomplete detoxification process. Iron cyanide is not removed and the potential for harmful by-products species exist. Consequently final effluents may be subject to additional treatment in order to comply with regulatory demands.

Jan 1, 1991

By L. A. Wrigglesworth, A. S. Dadson

The orebodies of the Giant Yellow-knife mine occur in zones of schist, in an assemblage of typical Precambrian greenstones which form part of the Yellowknife Greenstone Belt. One of the most interesting problems at the mine concerns the fold-like attitudes assumed by the schist zones. The internal structure of the zones and orebodies provides much evidence of folding. A logical conclusion would be that the zones represent a single horizon which has been folded and drag-folded in the ordinary course of mountain building. However, surface mapping, and correlation of certain marker horizons, in underground work, indicate a homo-clinal succession of steeply dipping flows. If this concept of the geology is correct, the zones must cross-cut the regional strike at a small angle and, in the over-all aspect, the regional dip at a large angle. A mechanical interpretation of the zone structure is presented as a suggestion for the present until new evidence is found.

Jan 1, 1959

By R. C. M. Minnitt, W. Dr. Assibey-Bonsu, F. A. Camisani-Calzolari

Born in Bothaville (OFS) on the 26th August 1919, Daniel G. Krige grew up in Krugersdorp on the West Rand. Hematriculated from Monument High School in Krugersdorpin 1934 at the age of 15 and graduated with a B.Sc. (Eng.)degree in mining engineering from the University of the Witwatersrand at the end of 1938 (age 19). In 1938 he joined Anglo Transvaal where he worked on a number of gold mines until 1943, gaining a wide range of valuable practical experience in surveying, sampling and ore valuation. He then joined the Government Mining Engineer’s Department where he worked for 8 years during which time he participated in the uranium negotiations with the British and American authorities and designed the uranium pricing formula for the contracts which led to the establishment of South Africa&apos;s profitable uranium industry in the early 1950s. During the same period he began his pioneering work in the application of mathematical statistics to the valuation of new gold mines using a limited number of boreholes and of ore reserves for existing mines. His early papers in the application of mathematical statistics, some republished in French, created world-wide interest that led to the development of the science and concepts that surround the spatial evaluation of mineral resources and reserves known as geostatistics. This technique has contributed to improved ore evaluation techniques as well as the reduction of the financial risks associated with investment in mining enterprises. Furthermore, it led to the recognition of his contributions to the evaluations of mineral deposits through the coining of the term ‘kriging’ that is used to describe a spatial mineral evaluation process known and practised in international mining circles. He continued his work in geostatistics throughout his career as Group Financial Engineer of the Anglovaal Group until his retirement in1981 and afterwards for ten years as Professor of Mineral Economics at the Witwatersrand University. He is still active as a consultant and is a registered Professional Engineer. He has published some 90 technical papers both locally and overseas, some in Russia, and has lectured and participated in international congresses in many countries. His contributions were recognized by the Witwatersrand University through the award of the D.Sc. (Eng.) degree in1963, by three honorary degrees (from the universities of Pretoria, UNISA and Moscow State Mining University), by many awards from the South African Institute of Mining and Metallurgy, the International Association for Mathematical Geology, Die Suid Afrikaanse Akademie vir Wetenskap en Kuns, the SME of the American Institute of Mining Engineers, the International APCOM Council in1999, the University of Antofagasta in Chile, and by the South African President (Order for Meritorious Service, Class 1, Gold). He has served on various Government committees, notably that for State Aid for gold mines (1967/8) and designed the State Aid formula which enabled many mines to survive a period of low gold prices; also various taxation committees, and the mining mission to Iran in 1974. He is a fellow and/or honorary life member of various technical societies locally and overseas, including the Royal Society of South Africa. During the period in the Government service he also handled several of the post-war lease applications in the Free State and Klerksdorp goldfields. The fact that decisions on new gold mines of critical importance to the State and the economy as a whole, were being taken on a limited number of drillholes without any scientific analysis of the risks of failure, stimulated him to start basic research into ore evaluation. His approach was based on the application of Mathematical Statistics to these problems, an approach of which very little was known world-wide at that stage but which had already been initiated in South Africa by Sichel via the lognormal frequency distribution model. In Krige&apos;s 1951 paper published in the Journal of the Chemical, Metallurgical and Mining Society of South Africa he covered the statistical explanation of the conditional biases in ore block valuations and stimulated the use by several gold mines of regression corrections for routine ore reserve valuations, a technique which, in effect, was the first use on an elementary basis of what is now known as kriging. His 1952 paper introduced, inter alia the basic geostatistical concepts of ‘support’, ‘spatial structure’,’ selective mining units’ and ‘grade-tonnage curves’. His 1951 paper was based on his M.Sc. (Eng.) thesis submitted in the Department of Mining Engineering to the University of the Witwatersrand, and expounded his pioneering work in geostatistics in more detail. His early research papers that had stimulated interest in several mining circles overseas, were republished in French in1955, resulting in a major research effort by French mining engineers in this field. This, in turn, led to the establishment of the now world-renowned French school of ore evaluation in Fontainebleau, Le Centre de Geostatistique de l’École des Mines de Paris. As the Group’s Financial Engineer at the Anglovaal Head Office until his retirement in 1981, he was responsible for

Jan 1, 2003

By T. Wennberg

An elevated location of a paste thickener on a ridge close to the disposal area is considered at a Swedish iron ore mine. About 0.7 M tonnes of thickened tailings are planned to be layered as paste in the vicinity of the thickener over several years with pipeline lengths of up to 900 m after about 20 years. In order to clarify the pipeline pumping characteristics of the tailings product for volumetric solids concentration from 40 to 50%, experiments in loop systems with pipeline inner diameters from 0.063 to 0.152 m have been carried out with various types of pumps. The results and comparisons carried out here showed that the performance of centrifugal pumps cannot simply be related to the rheology, but factors related to pump design and build-up tendencies of material within the pump and other particle properties may be of equal importance. During the first years of operation only one thickener underflow pump is required. The reliability and performance for various pump configurations are planned to be investigated systematically in order to meet the most effective long-term solution for paste thickener operation, pipeline distribution and placement in the disposal area as the discharge point advances over the life of the project.

Jan 1, 2007

By R. J. Matetic, J. Noll, C. Zhou, J. DuCarme, M. Reyes, J. Srednicki

"In April 2016, MSHA began requiring the use of continuous personal dust monitors (cPDMs) to monitor and measure respirable mine dust exposures to underground coal miners. After the cPDM’s implementation, mine operators discovered that it interfered with proximity detection systems (PDSs), thus exposing miners to potential striking and pinning hazards from continuous mining machines. NIOSH was sought out by MSHA and mining industry stakeholders to determine how the cPDM and PDS interact with each other. Accordingly, NIOSH investigated existing standards, developed test protocols, designed experiments, and conducted lab evaluations. Some interferences were observed to be caused by electromagnetic interference (EMI) from the cPDM. Results showed that there was no significant interference when the cPDM and the miner-wearable component of the PDS were separated by distances of 6 inches or greater. In this study, the cPDM and PAD needed to be at least 6 inches apart in order for them to be used simultaneously and reduce interference potential. INTRODUCTION Underground coal miners are exposed to a variety of hazards on a daily basis such as coal dust exposure, high noise levels, roof and rib falls, the potential for fires and explosions, and operating and working with heavy machinery. One of the hazardous jobs is operating or working nearby a continuous mining machine (CMM). According to Mine Safety and Health Administration (MSHA) statistics, 40 miners have been fatally struck or pinned by a CMM since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems have been developed and are required on all operating CMMs in underground coal mines, with the exception of full-face CMMs, by 2018 (1,2). Proximity detection systems (PDSs) are designed to alarm miners and stop machine motion in order to protect miners from being struck, pinned or crushed by CMMs(3). Currently, MSHA-approved PDSs, installed on CMMs, are based on the principle of magnetic flux density (B-field) (4,5). The system generates a magnetic field around a CMM and determines the relative distance a miner is from the CMM based on a detected magnetic flux density. A PDS typically consists of multiple magnetic field generators mounted at different places around the CMM, and personal alarm devices (PADs), which are worn by the miners to detect the magnetic flux density. When a miner, wearing a PAD, gets closer to the machine, the PAD detects a stronger magnetic field from the generators and detects a weaker magnetic field when a miner moves away from the machine. The magnetic field generators installed on CMMs typically produce modulated magnetic wave signals at frequencies between 10 kHz and 120 kHz. The magnetic fields are measured by three small magnetic coil antennas mounted on orthogonal axes inside of the PAD worn by the miner. According to Faraday’s Law, the changing magnetic field induces a voltage in each coil antenna, and the voltage values are transmitted from the PAD back to a controller on the CMM wirelessly, typically at a frequency between 400 MHz and 2.5 GHz. These values are then used to determine the distance between the miner and the generators of the machine. Typically this information is used to determine when a miner wearing a PAD is in a warning zone or stop zone which would trigger different alarms and actions such as slowing the machine down or stopping it."

Jan 1, 2017

By Lawrence Adler

The properties of a geologic mass may be considered from a resource or an engineering viewpoint. The primary engineering applications include ground control, excavation, bulk handling, and hydrology. This study will focus upon these areas in descending order. For an adequate geologic description, data is necessary on the following components: (1) the intact rock, (2) geologic structures, (3) contained fluids, and (4) existing pressures and temperatures, see Table 1. This information, combined with the engineering specifications, provides the basis for a formal geotechnical analysis as illustrated in Figure 1. For a structural analysis it is essential to establish the mechanical properties of the material composing the structure. This material, termed the "rock mass," consists mainly of the first two geologic components, the intact rock and geologic structures (Figure 1) Consideration of fluids will be subordinated to their role as chemical agents affecting the mechanical properties. The existence of pressures and temperatures generally lies beyond the scope of this study.

Jan 1, 1973

By Huw Williams

It is becoming increasingly common practice to re-use existing foundations for new projects, especially on urban sites where geotechnical conditions are congested. A knowledge of the foundation dimensions and capacity is essential for this to take place, however, as-built records are often non-existent. Non-Destructive evaluation (NDE) is now becoming an important tool in assessing old foundation properties and their potential for re-use. Pile dimensions are also critical in the power industry, when they are supporting transmission towers which need to be upgraded, and may carry additional wind loading. This paper describes the application of various NDE techniques that are available and how they can be used to determine pile length, shape and capacity in difficult site conditions, including foundations under structures.

Jan 1, 2006

By Karl Fetters

IN the process of making steel in the open-hearth furnace the refining of the metal during the working period of the heat is largely accomplished through the agency of the slag. From the birth of the process until the present day steelmakers have recognized the importance of the slag in determining the composition of the metal and the quality of the product. The general relationships between slag composition and metal analysis have long been known, at least in a qualitative or approximate fashion. For examples, the iron oxide content of the slag is higher on lower carbon heats; the more basic slags are higher in iron oxide for a given carbon content; certain amounts of iron oxide and lime are required for phos-phorus removal and a high lime-silica ratio is needed if the sulphur content of the metal is to be diminished. In recent years a number of quantita-tive relationships involving these and other variables have been developed through plant and laboratory studies by numerous investigators in this country and abroad. The direct comparison of laboratory and open-hearth data involves the question of the degree to which each approaches the conditions of chemical equilibrium, a question which, from the open-hearth standpoint, we are scarcely yet in position to answer. And, although a considerable body of dependable equilibrium data has been obtained in the laboratory, this work has not yet been extended to cover the ranges of slag composi-tion encountered in basic open-hearth practice. In the present study we shall not attempt to draw comparisons between data from the two sources; nor do we attempt to draw conclusions as to the approach to chemical equilibrium in the open-hearth furnace. Many of the operating variables that are likely to be erratic or unrecorded during the earlier stages of the heat become more consistent and are more readily subject to observation and control during later stages. For example, undigested lime or ore gradually goes into solution, the rate of carbon drop levels off, and the temperature of the metal is brought under control. For these and other reasons a greater degree of self-consistency is likely to be found among data obtained during the

Jan 1, 1940

By J. -P. Chilès

The discrete Gaussian model is a very popular change-of-support model for estimating block grade distributions. It is designed for a stationary random function Z(x) that is regarded as the transform of a stationary random function Y(x) with Gaussian marginal. It is based on an assumption that is not fully true and thus constitutes an approximation to the exact solution. We examine the effect of this approximation on the modelling of the marginal distribution of block values of a lognormal random function. The initial discrete Gaussian model and a variant of that model are considered.

Jan 1, 2014