Search Documents

By John Nagy

Data from experiments and literature on gas and dust explosions in closed vessels are presented to show the effects of the vessel size and shape; the initial pressure, temperature, and turbulence; and the fuel-air ratio and the strength of ignition source on pressure and rate of pressure rise. An attempt is made to correlate some of these parameters with an elementary mathematical model. Analyses of data on 17 vessels--spherical, cubical, cylindrical, and rectilinear in shape--ranging from 0,018 to 905 cubic feet in volume were made. Although the study was initiated to provide information primarily on dust-explosion phenomena, some data were obtained for gas explosions so that the factor of initial turbulence caused by the pneumatic blast used to disperse dust could be evaluated. The mathematical interpretation of the explosion phenomena was in general accord with the experimental data, and correlation was obtained for several factors affecting explosion development. Neither vessel size nor shape affected maximum pressure (when heat loss was neglected). The rate of pres-sure rise decreased as vessel size increased, and the rate was proportional to the ratio of the surface area of the vessel to its volume. Induced initial turbulence markedly increased the rate of pressure rise and slightly increased the maximum pressure. Changes in initial pressure produced proportional changes in maximum pressure and rate of pressure rise. Initial temperature and maximum pressure were inversely related, but initial temperature had little effect on the maximum rate of pressure rise. Comparative experiments showed no appreciable difference in explosion development of gas and dust fuels. The vessels and experimental work are described, and all data are given in tables. The mathematical model will facilitate extrapolation from laboratory to industrial conditions and will allow comparison of results obtained in different laboratories.

Jan 1, 1971

By R. Q. Honaker

A significant problem in ultrafine particle classification is the significant amount of submicron particle by-pass to the coarse particle stream. In classifying cyclones, submicron particle by-pass to the underflow stream can be reduced by decreasing water recovery. Past studies have shown that a reduction can be realized when the feed solids concentration is increased or the apex diameter is reduced. However, both adjustments tend to increase the particle size cut point and negatively affect classification efficiency due to the impact on slurry rheology. The addition of a viscosity modifier to the feed stream of a classifying cyclone improved the classification performance and decreased the particle size cut point over a range of feed solids concentrations. The detailed test program investigated the use of the modifier in conjunction with varying apex diameters to identify conditions that minimize ultrafine by-pass. With small apex sizes, roping conditions were readily eliminated by the addition of viscosity modifiers. The addition of the modifier had no deleterious effect on froth flotation performance, which commonly serves as a downstream separation process. The fundamental and practical benefits of viscosity modifiers in classification processes are discussed in this publication.

Jan 1, 2006

By R. J. Boyd

SUMMARY The productivity of drill and blast methods of mining in hard rock is limited by the cyclic nature of the operation, and a plateau of performance has been reached, even with the most advanced equipment developments. Higher mine operating costs and lower metal prices have more than ever generated the need for breaking through these productivity barriers. After initial field testing The Robbins Company has designed and manufactured, on a joint venture basis with Mount Isa Mines, Ltd., Australia, a prototype "Mobile Miner" for continuous cutting of hard rock. This paper describes the cutting concept, the initial application of a completed 1,156 m (3792 ft.) long 14% decline, actual performance and delay analysis, developmental modifications, anticipated performances of a fully developed machine, and possible future applications. Sincere appreciation is expressed to the management of Mount Isa Mines, Ltd., for allowing access to the data used in this paper. The views expressed here are those of the author and not necessarily those of Mount Isa Mines, Ltd. INTRODUCTION A paper titled, "Design and Development of a Mobile Mining Machine", was presented by J.P. Kindsvater at the RETC, New York, in 1985. This paper described the evaluation of a test fixture in an andesite quarry near Seattle, followed by design, construction and

Jan 1, 1987

By R. L. Montgomery

The heats of solution of erbium chloride in water and in hydrochloric acid and of erbium oxide in hydrochloric acid were determined. The results reveal a discrepancy of 10.5 kcal. per gram-atom between the heats of combustion and solution of erbium reported in the literature, the heat of combustion being more negative. The heat of combustion of erbium t4)4 and its heat of solution in hydrochloric acid (1, 18) have been reported in the literature. The heat of solution of erbium chloride was determined in two studies (2, 19). The present work was undertaken to check the reported heats of solution of erbium chloride and to determine the heat of solution of erbium oxide in hydrochloric acid. The latter quantity permits the heats of combustion and solution of erbium to be compared for mutual consistency. It was also desired to determine the degree of similarity between the thermochemistry of yttrium and erbium.

Jan 1, 1961

By A B. Richards

Time window analysis that limits the explosive mass fired within a specified time window (commonly eight milliseconds) has been used for many years in blast design by explosives engineers. Despite several warnings in the past that this technique has limited practical or scientific basis and, in many cases, does not effectively control vibration, almost every textbook and blasting manual refers to time window charge mass limits as a primary vibration control technique. It has become entrenched in some blast vibration management plans, despite being inappropriate for the particular situation. With the flexible initiation timing available with electronic detonation almost a practical reality, and the 8 ms constraints in-built into the signal tube initiation system thereby lifted, it is timely to review the significance of the 8 ms time window in controlling blast vibration. This paper re-visits the original research that led to the development of the 8 ms criteria and the non-supportive conclusion of the original researcher. Because airblast was not measured, the 8 ms time window was never intended to be applicable for airblast control. Examples of blast designs are given in this paper that comply with the 8 ms time window limit that result in substantially increased air and ground vibration, together with examples of blast design that does not satisfy time window considerations, which results in reduced air and ground vibration. Techniques that identify wavefront reinforcement, due to the combined effect of drilling pattern and delay sequence, can assist explosives engineers to avoid high blast vibration situations that result from the inappropriate application of time window techniques and other adverse delay combinations.

Jan 1, 2003

By C. M. Tucker, Kent R. Van Horn, W. P. Sykes

RECENT investigations of the molybdenum-carbon alloys have been reported by Becker and Ebert1‡, Westgren and Phragmén2, T. Takei3, and H. Tutiya4. Takei3 studied the Mo-C system by employing metallographic and X-ray methods, and the other publications described the determination of the crystal structure of the molybdenum carbides. In exploring this system by a technique previously applied to the tungsten-carbon series5, the results of Takei were confirmed with two definite exceptions; i.e., first the composition of the eutectic, and second the nature of the carbon-fish intermediate phase. Consequently, a more thorough examination of the molybdenum-carbon constitution was initiated in an effort to correlate the data supplied by the microstructures, diffraction patterns and chemical analyses. METALLOGRAPHIC INVESTIGATION A briquette of molybdenum powder when heated in a carburizing atmosphere at 1500° to 1600° C. for several hours develops the carbon-rich layer shown in Fig. 1. The carburization was accomplished by placing the briquette in a carbon tube, which was heated in the hydrogen atmosphere of an alundum muffle wound with tungsten resistor. While the macrostructure indicates two distinct shells, and suggests the possibility of two carbon-rich phases, no evidence of this condition could be detected by the microscope, which revealed but one high-carbon constituent. This carbide forms next to the molybdenum as a relatively

Jan 1, 1935

By O. R. Morris, G. L. Hawkes

A galvanic cell, using as electrolyte a fused salt solution of calcium carbide and as electrodes carbon and a Fe-C alloy of known composition, has been set up to study the thermodynamics of Fe-C alloys in the temperature rmzge 800" to 1000°C. Time independence and reproducibility of the cell electromotive force were taken as evidence of the reversible behavior of the cell. Carbon was believed to be present in the electrolyte as the so-called acetylide ion, C;-. The plots of the cell electromotive force us temperature for a specific alloy composition were straight lines within the limits of experimental error. The average Partial molar enthalpy of carbon in iron relative to pure carbon was found to be +10,610 i 93 cal per g-atom C. Thermodynamic analysis of the data has led to the following equation for the carbon activity, ac, based upon pure carbon as the standard state: In ac = In Zc + 10,560/RT + (10.02 + 77O/T)ZC - 2.350 where ZC is the lattice ratio [nC/(nF, - nc )] and T is the absolute temperature. This equalion gives carbon activity values generally slightly lower than those from gas equilibration studies reported in the literature. METAL LOGRAPHIC examination of a polished cross section of the steel anode used in the electrolysis studies of fused salt solutions of calcium carbide by Morris and Harry revealed extensive carburization of the steel by the electrodeposited carbon. This carburization was reflected in the variability, with time, of the applied potential to the electrolysis cell, necessary to maintain a constant current density at the electrodes. This observation suggested the setting up of a galvanic cell of the "alloy concentration" type to study the thermodynamics of some metal-carbon alloys. Cells of this general type have been widely used for the study of alloy systems.2 In view of the availability of published data in respect of the austenite phase of the Fe-C system, it was decided to carry out measurements upon these alloys before proceeding to studies of less well documented systems. The galvanic cell may be written: where [C] is carbon dissolved in iron. The electrolyte was a fused salt solution of calcium carbide, containing some 5 to 10 mol pct of carbide. The cell reaction is believed to be: C(s)-[CI [I1 Carbon forms an interstitial solid solution in iron, with the atoms located in the octahedral interstices. In the fcc crystal structure of austenite there is one octahedral interstice per iron atom. Thus, the lattice ratio, ZC, shown by Gurney3 to be the fundamental concentration parameter in the context of interstitial solutions, is given by: where nc and nFe are the number of carbon and iron atoms, respectively. chipman4 has recently shown empirically the advantages of using this concentration parameter instead of the more usual atom ratio or atom fraction. The cell electromotive force, E, assuming reversible behavior, is related to the carbon potential or the partial molar free energy of carbon in the solid solution relative to pure carbon at the same temperature and pressure, GP at the composition ZC, by the equation: where z is the carbide ion valency and F is the Faraday constant. An activity of carbon, ac, in the solution relative to the value of unity assigned to pure carbon, and an activity coefficient, qC , are defined such that: where R is the gas constant and T the absolute temperature. GF is further related to the relative partial molar enthalpy Hm, and the temperature coefficient of the cell electromotive force, (aE/aT)Zc, by the equations: Measurement of the cell electromotive force thus enables calculation of the relative partial molar thermodynamic properties of carbon in iron, if z is known. At E = 0, the solid solution is in equilibrium with pure carbon. More convenient for many purposes is the standard state based upon the infinitely dilute solution, Henry's law. The relationship between the activity coefficient of carbon based upon this standard state, and that based upon the pure carbon standard state, qC , may be obtained by considering the free energy of transfer of carbon from the latter standard state to the former. The relationship is: where +:H is the activity coefficient of carbon in the hypothetical standard state based on a reference of

Jan 1, 1969

By James R. Dunn

The nature of water and clay in carbonate rocks is currently being investigated at Rensselaer Polytechnic Institute by various thermal and sorption techniques. Two basic concepts 'led to the present research. (1) To explain the expansion and contraction on wetting and drying of some unsound argillaceous carbonate rocks, it was postulated that the pore space around each clay particle is such that when water is sorbed by the clay, force is exerted against the pore walls. (2) The clays in expansive rocks are rejected from the growing dolomite crystals during their growth, and form a more or less connected network, thereby becoming "wettable," or available to water. New quantitative cold differential-thermal-analysis (electrocalorimetric) equipment was designed and constructed to check the "limited space" and "wettable clay" concepts and to determine the thermal nature of the transition of water to ice in rocks. This DTA equipment can detect the release of heat in freezing of less than 0.001 per cent water in a rock. Twenty-three rock cores (nine sound and fourteen unsound) and 4 procelain cylinders for standards were studied. In the nine sound rocks and in all the procelain cylinders, the rapid freezing of from 50 to 100 per cent of the water was readily detectable after 7 to 10° C of supercooling. No further freezing could be detected to -20° C. However, in eleven of the fourteen unsound rocks, no freezing was detected to as low as -40° C; in the other three, less than 50 per cent of the water froze. As a check of the DTA measurements, adsorption isotherms were determined for all materials. Calculations of theoretical freezing points for sorbed water again demonstrated that the least sound rocks had the most nonfreezable water. "Frost" sensitivity in these carbonate rocks is, therefore, probably not the result of the force of expansion of water to ice. The disruptive force is believed to result from expansion of sorbed, ordered water on clay surfaces. The relationship between the unfilled rock pores after 24-hour water saturation and the water sorbed at 85 per cent humidity at 30° C (i.e., the theoretical nonfreezable water delineates the sound and unsound carbonate rocks.

Jan 1, 1966

Consumption and intensity of use trends for 12 metals, by industrial end use, were estimated for 1972 through 1982 by the Bureau of Mines and U.S. Department of Commerce. The trends were then forecast through 1993 using standard statistical methods. The intensity of use measure selected is the quantity of metal consumed per constant dollar output of a specific industrial sector. The metals studied were aluminum, chromium, cobalt, copper, lead, manganese, nickel, the platinum-group metals, tin, titanium, tungsten, and zinc. Average annual growth rates for the following 4 of the 12 metals increased from 1972 to 1982 as follows: aluminum, 1.00%; platinum-group metals (consisting of platinum, palladium, and iridium), 8.83%; titanium, 7.82%; and tungsten, 6.09%. Consumption for the remaining eight metals decreased at average annual rates ranging from 0.58% (copper) to 5.37% (manganese).

Jan 1, 1986

By R. P. Carreker

ONE of a series, this report is concerned with the experimental documentation of the deformation behavior of pure metals over a wide range of temperature. Previous reports in the series describe the creep behavior of platinum1 and aluminum2 and the tensile behavior of copper,&apos; silver,& and molybdenum.5 Subsequent reports will describe the creep behavior of copper and silver and the tensile behavior of platinum, thus providing extensive creep and tensile data on four face-centered-cubic metals tested under comparable conditions. Material Two lots of high-purity aluminum were used in this investigation. One lot, designated AC, was obtained direct from the Aluminum Co. of America as high-purity aluminum in notch-bar form. A typical analysis of this type of aluminum is 0.006 pct Si, 0.015 pct Cu, 0.006 pct Fe, and 99.975 pct Al. Lot BS was obtained from J. I. Hoffman of the Bureau of Standards as a portion of the Aluminum A described in his report of the redetermination of the atomic weight of aluminum.6 Lot BS originated with the Aluminum Co. of America also, and was received in the standard notch-bar form. A detailed chemical and spectroscopic analysis of lot BS has been published.6 Principa1 impurities were 0.006 pct Si, 0.003 pct Fe, 0.002 pct Cu, and >99.987 pct Al. Samples were processed identically by room-temperature swaging and drawing to 0.030 in. diam wires from approximately ½ in. diam rods that were machined from the notch-bar pigs. Samples were cut from the cold-drawn wire, placed in a grooved graphite block in groups of thirteen, and annealed in air for 1 hr at each of several temperatures, with the results shown in Table I. The two lots of aluminum responded quite differently to annealing, the behavior of aluminum AC suggesting that its grain growth was controlled by impurities. The recrystallization texture of aluminum of similar purity comparably treated has been reported as predominantly <111> fiber with some <100> fiber present.7 Testing Procedure The testing procedure and method of analyzing the data have been described previously.2,3 Annealed specimens of 5 in. gage length were tested in an Instron tensile testing machine at a constant head motion corresponding to a strain rate of 0.04 min-&apos; at a number of temperatures. Instantaneous tenfold rate changes were employed in some tests to deter-

Jan 1, 1958

By Alan G. Mayton

The Bureau of Mines conducted a study to (1) determine from laboratory tests the feasibility of a photographic method for determining reflec-tances that may be applied to measuring in-mine mineral reflectances and (2) formulate a procedure for collecting and analyzing the data. The method uses a 35-mm camera with automatic flash and a gray-scale re-flectance standard to collect on film the reflectivity data in under-ground mineral mines. After the film is processed, the data on the photographic prints are analyzed in the laboratory with a photometer. Test results show the photographic method can provide values of reflec-tance to within ±5 pet of full scale (full scale = 100 pet). The method&apos;s usefulness for determining reflectivity values, within similar limits of absolute percent error at the lower end of the scale, however, has not been completely resolved by the study and consequently warrants further investigation. The method offers an acceptable means for collecting and analyzing reflectivity data for reflectivities at the higher end of the scale, i.e., 50 pet or above; it should be used with caution when reflectivity values are below 50 pet. Four films were evaluated; all gave relatively satisfactory results.

Jan 1, 1987

By B. K. Cantrell, K. L. Rubow

"Quantifying exposure to diesel exhaust aerosol in an underground coal mine depends on the ability to measure this component of respirable mine aerosol separately from coal dust. Such measurement is complicated by the carbonaceous nature of both the diesel and coal dust particulate that make up the respirable aerosol. Hence, special sampling and analytical techniques must be used to distinguish between these two aerosol components.As part of a continuing study of diesel exhaust aerosol characteristics, the U.S. Bureau of Mines has applied size selective sampling together with gravimetric analysis to separate and measure respirable diesel exhaust and coal dust aerosol concentrations in diesel-equipped underground coal mines. This technique is based on the premise that the diesel portion of the aerosol is predominantly submicrometer and the mineral dust portion is mostly greater than 1 µm in size. In the study, chemical mass balance (CMB) modeling, based on the distribution of chemical elements in aerosol and aerosol source material samples, is used to referee the analysis of diesel exhaust and mineral dust aerosol concentrations from the size selective sampling results.Based on the results of the study, the Bureau, in cooperation with the University of Minnesota and the U.S. Mine Safety and Health Administration (MSHA), have developed a prototype personal diesel exhaust aerosol sampler for underground coal mines. The sampler has three stages: a preclassifier stage to select for respirable aerosol, an inertial impaction stage with an aerodynamic diameter(d) size cut at 0.8 µm to separate diesel aerosol from mineral dust and collect the mineral dust, and a final filtration stage to collect the diesel fraction of the sample. The sampler has been evaluated in both laboratory and field experiments conducted by the Bureau, MSHA, and the Generic Minerals Technology Center for Respirable Dust (GMTC-RD)."

Mar 1, 1992

By Jian Zhang

From the standpoint of quality, surface cracks normally pose more of a problem than internal cracks. Hypo-peritectic (HP) steel grades are well known for their proneness to surface longitudinal cracking (SLC) during continuous casting. This study analyzed the influences of chemical composition, technique parameter and secondary cooling on the surface longitudinal cracks. Based on the optimized the first and secondary cooling zone water distribution in the process of continuous casting, low cooling water distribution at solidification initial stages and uniform cooling at secondary cooling zone were suggested, which can be used to effectively control the surface longitudinal cracks.

Jan 1, 2010

By C. H. Pitt

A jet slurry apparatus has been constructed to test corrosive/erosive wear properties of grinding ball metal. Plain high carbon steel heat treated to a hardness of about 60 RC was used. Slurries of quartz and chalcopyrite ore concentrate were used as the jetting media. Weight loss due to pure corrosion was determined by the linear polarization technique and weight loss due to pure erosion was determined by jetting while cathodically protecting the sample. By comparing the total weight loss with the sum of the weight losses from pure corrosion and pure errosion it was found that there was a synergistic effect between corrosion and erosive wear. Erosive wear rates are given as a function of pH and mineral type.

Jan 1, 1984

By Ernesto Maldonado, Jesus Romero Benitez, Zach Agioutantis

Numerous researchers worldwide have investigated the prediction of ground movements due to underground coal mining utilizing different analytical, empirical, and numerical models. These studies have primarily focused on the development of prediction methodologies for either flat or gently dipping seams under variable topography, and only a few studies are available that have investigated the prediction of ground movements over inclined seams. Although most inclined coal seams are in China, India, and other countries worldwide, a few inclined coal seams (with a dip of 10 degrees or greater) are also present in the US. Currently, the prediction of ground movements for inclined coal seams using empirical methods utilizes the same methodology for horizontal seams. It consists of dividing the inclined seam into horizontal segments, calculating deformations due to each segment, and superimposing the calculation results. This paper presents a new tool that provides a methodology for modeling subsidence under inclined seam conditions. Examples based on subsidence measurements available in the literature are presented. The goal is to implement this methodology into the Surface Deformation Prediction System (SDPS).

Jun 25, 2024

By Ware AR, Doyle BJ, Hoogvliet H

The Ladolam deposit lies within the altered volcanic rocks of the caldera floor, part of which now forms Luise Harbour. It was discovered in 1982 in the course of a reconnaissance drainage sediment sampling programme. This was designed to follow up indications of surface hydrothermal activity noted by Government geologists during an earlier survey of the Tabar-Feni island chain. Diamond drilling began in September 1983 and by the end of 1989 a payable and proved mineable reserve containing 19 million ounces of gold had been established. Rock types and structures are masked at the surface by intense alteration and weathering. An extensive drilling programme has enabled the identification of these features and the relationships between them necessary for an understanding of the factors controlling gold mineralisation. It has also led to the recognition of two distinct phases of alteration. The first phase of porphyry-style potassic alteration was followed by violent caldera formation, producing extensive brecciation and veining. The second alteration phase partly over- printed the first phase and was an epithermal one, evidenced by argillic, advanced argillic and phyllic assemblages. During this event, a large volume of fluids circulated under the favourable structural conditions; these fluids included a sulphur- rich, neutral chloride brine believed to have transported the gold. Boiling and mixing of circulating fluids in the open breccias is thought to have resulted in deposition of the gold. There is evidence that this process is continuing at the present day.

Jan 1, 1991

By Donald E. Redmon

Industrial engineering departments perform staff duties and are most effective when sincerely supported by management. In accordance with the needs and desires of the mining companies involved, various industrial engineering functions have been adopted widely at western metal mines during the period 1950-60. Newly organized departments usually conduct method and equipment studies, work-measurement programs, and establish and maintain production standards. Supervisor-training programs and courses are effective in showing the relationship between supervisory responsibility and the purpose for which industrial engineering is practiced. Industrial engineering staffs of western metal mines are composed predominantly of personnel from within the companies. Experienced industrial engineers, not necessarily experienced in mining, frequently are hired by a company to help establish the department. Management consultants frequently are called upon to advise management and instruct department personnel in industrial engineering practices. Some departments have developed satisfactory industrial engineering programs without benefit of formal industrial engineering training or advice.

Jan 1, 1962

By Roy A. Koski

This paper describes variations in feed characteristics, preparation techniques, response to induration and product quality in pelletizing magnetite concentrates, earthy hematite ore fines, and specular hematite concentrates in grate kiln systems. The Cleveland-Cliffs Iron Company manages plants processing these various materials on the Marquette Iron Range in northern Michigan. The operations include the Humboldt Mining Company, Marquette Iron Mining Company, Empire Iron Mining Company and the Pioneer Pellet Plant. The combined output of the operations is approximately 9,000,000 long tons per year. The Humboldt Mining Company, owned by Ford Motor Company and Cliffs, produces pellets from a specular hematite concentrate. The Empire operation, which processes magnetite ore, is owned by Inland Steel Company, McLouth Steel Corporation, International Harvester and Cliffs. The Pioneer operation, which processes earthy hematite ores, is a joint venture of Republic Steel Corporation, McLouth Steel Corporation, Bethlehem Steel Corporation and Cliffs. The Marquette Iron Mining Company, owned by hones and Laughlin Steel Corporation, International Harvester, Wheeling-Pittsburgh Steel Corporation and Cliffs, produces pellets from specular hematite concentrate at the Republic Mine and Eagle Mills Pellet Plant. With the exception of the Eagle Mills plant, the operations employ the grate-kiln pelletizing system. Descriptions of the Empire, Pioneer and Republic operations, which have a combined capacity of 7,200,000 tons per year, are given in the paper.

Jan 1, 1969

By J. G. Walters

Analyses of light oils produced from the fluidized carbonization of coal at 485°, 550°, 600°, and 660° C are presented. Tar vapors from 485 C fluidized carbonization were thermally treated at 600°, 700°, and .800° C, and the analyses of light oils produced by this treatment are also presented. Procedures were developed for analysis of coal carbonization light oil by gas chromatography to permit a more definitive analysis than can be obtained by the conventional distillation procedure. An increase in low-boiling olefins, benzene, and toluene, a decrease in low-boiling paraffins, and little change in the remainder of the aromatics was observed with increased temperature of carbonization.

Jan 1, 1965

By T Hodgkin

The WA Goldfields is a highly productive gold and nickel mining area, but is arid with highly saline groundwater. Groundwater is widely used to supply process water to mines in the region but high groundwater salinity, commonly exceeding 50 000 mg/L TDS, tends to increase processing costs, limit end uses for the water, cause problems with disposal and potentially increase impacts on a sensitive arid environment. The area has low rainfall (200 - 270 mm/year) but run-off, particularly during cyclonic events, is high. Our experience suggests that stream flow from catchments in the area can produce a divertible yield of 8 - 17 ML/km2/year. An evaluation of stream flow harvesting using AnglogoldÆs Jubilee Pit predicted that 1000 ML/year of good quality water could reliably be supplied to the Sunrise Dam Gold Mine. Because of high rainfall variability, it is likely that an alternate source of water supply will be necessary when operating a surface-water harvesting scheme in the WA Goldfields. However, a combination surface/groundwater supply could have substantial cost, operational and environmental benefits compared to traditional supply systems that utilise groundwater only.

Jan 1, 2003