Search Documents

By C. D. Harrison, G. S. Stallard

The 199O Clean Air Act Amendments specify national objectives for reducing sulfur dioxide emissions from coal fired power plants. System-wide reductions can be achieved by combining various emissions control technologies and allowances, or compliance credits, that can be purchased, sold or traded. As part of the Coal Quality Expert development project funded by the US Department of Energy and the Electric Power Research Institute (EPRI), Black & Veatch has developed an interactive computer tool, the Acid Rain Advisor (ARA). Through this program, integrated, system-wide compliance plans are generated by comparing the costs and emissions reduction benefits of emissions allowances and various SO2-control technologies (coal cleaning, fuel switching, scrubber retrofits, etc.)

Jan 1, 1993

About 15 per cent of total electricity (400 MkW) was generated by nuclear power plants in the world (2009) and about 36 000 tons of uranium has been mined in uranium mines annually. Radioactive waste material is produced from uranium mines and nuclear power plants. The wastes must be disposed or stored safely for long-term. If they leak and/or move from disposal or storage sites due to air/groundwater flow, then a serious environmental pollution can occur. Hence, multi-layer system has been proposed and employed in order to seal off these radioactive waste materials from biosphere. Basically, bentonite is now used for establishing absorbing and sealing layers in this system. However, the amount of high quality betonite is very limited and in some cases it is hard to be obtained.On the other hand, a great deal of refuse from coal burning plants is produced every year and the amount of it is expected to be higher each year, especially in developing countries. More than half of flyash is utilised and the remaining is disposed at the disposal sites. However, the life of the disposal site is limited and it is diff cult to find a new disposal site. It is requested that the percentage of the utilisation of the flyash be increased in every field.From the above two points of view, a flyash-based barrier layer/cover system is considered in this research and this paper discusses the applicability of flyash as a content of barrier layer/cover material based on the results of a series of laboratory tests.

Dec 6, 2010

By H. J. Garcia

Biodegradation of cyanide by microorganisms isolated from solids previously exposed to cyanide has been investigated. Initial sodium cyanide concentration was 300 ppm at pH 10.5. The kinetics of biodegradation were found to be first order with respect to cyanide concentration, and the overall reaction rate constant is k = 0.102 day-1. The activation energy and the frequency factor were determined to be { A }Ea = 5.45 Kcal/mol and A = 1.28 x 10-2 sec-1, respectively. Based on these values, thermodynamic properties of an intermediate activated complex were assessed. All tests resulted in cyanide concentrations less than 0.1 ppm in about 35 days at 250C, whereas at 350C the time of biodegradation to reach this cyanide level was 30 days. Kinetic data were also established to relate biodegradation to amount of inoculum. The maximum theoretically-attainable rate, Vm , and the optimum amount of inoculum, K , were determined to be 4.8 x 10-4 M NaCN/day and 7.5 % of amount of inoculum. With respect to the mechanism of biodegradation, cyanide was shown to decompose to carbonate, bicarbonate and ammonia. Titrimetric analyses revealed concentrations of 5.6 x 10-3, 4.8 x 10-3 M, and 70.2 ppm for carbonate, bicarbonate and ammonia, respectively. The average cell population was determined to be 3.75 x 108 cells/mL.

Jan 1, 1994

By Witold M. Pytel

A simplified, three-dimensional, time-dependent, mechanistic model of the overburden-coal seam-floor interaction has been developed and validated at two Illinois coal mines. The model based on the thin plate theory can involve any complex layout of mine workings, time-dependent sequence of extraction and, rheological properties of immediate floor strata. The model output data consist of spatially distributed surface subsidence and its slope and curvature, as well as load acting on pillars in one or more panels. A comparison of calculated and monitored surface subsidence or in-mine convergence measurements has proven the model's effectiveness for surface subsidence and load transfer prediction.

Jan 1, 1992

By W. L. Price

Recent publication of United States Bureau of Mines figures showed that the sand and gravel (3) industry is the largest single mining industry in the United States in term of yearly tonnage produced. The yearly production of over 500,000,000 tons per year now exceed bituminous coal production. This disclosure caught unawares many observers who have not been following closely the rapid-growth of this phase of mining. Along with this steady growth in production, the sand and gravel industry has gone through an accelerated and varied program of beneficiation in a period of the last ten years.

Jan 1, 1958

By Anthony T. Jones

Deep seabed mining requires technology to collect materials and transport them to the surface. An international patent search was conducted to define the state of the art in seabed mining technology. Over 350 patents were identified from 12 patent systems. The majority was from the United States, Japan, and the former USSR. Patent activity in this field peaked in 1983 when 34 patents were issued. Since 1984, on average 6 patents have been issued annually. The technology represents ten major classifications. With the exception of Deepsea Ventures, Kawasaki and International Nickel, it appears that much of the technology developed and tested in the 1970s by consortia active in seabed mining was never patented. Over the past two decades, identifiable trends in marine technology could influence seabed mining application such as more sophisticated communication systems, advances in hydraulic manipulators, improved computational technology in navigation, modeling of vessel ? ocean interactions, and improved materials. The most significant recent activity has been in European applications, which disclose remotely controlled subsea vehicles for mining diamonds.

Jan 1, 2001

By H. M. Friede

An experimental study of iron-smelting techniques used in the South African Iron Age by H. M. FRIEDE, Ph.D. and R. H. STEEL (Visitors) The main factors involved in the primitive smelting of iron (ore, charcoal, temperature, air supply, process control) were evaluated in an experimental furnace that was constructed to the pattern of an Iron Age furnace found at Melville Koppies Nature Reserve, Johannesburg. In particular, the characteristics, action, and efficiency of skin bellows were investigated to gaina better understanding of the air-supply system used. Sixteen specimens of iron ore, slag, and metallic iron (excavated material and material produced in the experimental furnace) were submitted to analysis. The results of the analyses are reported and discussed.

Jan 6, 1977

By W. Krieglstein

Due to the natural variability of ores, it is necessary to carefully test flotation behavior of flotation cells before designing flotation circuits. For performing quick and versatile tests in the laboratory, Siemens developed a laboratory-size Hybrid Flotation Cell, which has been down-scaled from the 300 m³/h production cell to a 0.6 m³/h flotation cell. This small cell is being used as a test bed for technical and chemical concepts, the improvement of decisive components and the characterization of customer ores. In this study the evaluation results for Andean porphyry copper ores are shown. Total recovery rates of the order of 45 to 50 % have routinely been achieved in a single flotation cycle over a wide range of feed grades. In addition, the Hybrid Flotation Cell has proven to be particularly well suited for the flotation of fine particles below 20 µm down to below 1 µm, at high recovery rates and concentrate grades.

Sep 1, 2012

By S. A. G. Poppen, M. B. Mirza, A. I. Cooley

The U.S. Department of Energy (DOE) is responsible for siting and constructing a licensed geologic repository for commercially generated high-level nuclear waste. Within DOE, the Office of Civilian Radioactive Waste Management (OCRWM) Program has this responsibility. To accomplish this mission, the OCRWM Program is engaged in a multidisciplined effort to identify, qualify, and develop repository sites. The current strategy of the OCRWM Program is to identify candidate repository sites in basalt, tuff, and salt and to develop exploratory shafts at those sites. Within OCRWM, the Salt Repository Project Office (SRPO) identified the salt site for the development of exploratory shafts. The proposed Exploratory Shaft Facility (ESF) in salt will have several primary purposes. The shafts will provide access to the reference repository horizon to permit in situ testing of the salt horizons in order to satisfy the following data acquisition needs: • Verification of the salt repository design parameters and validation of performance assessment models • Demonstration of the constructibility • Capability to adequately seal penetrations into the salt An exploratory shaft is required by 10 CFR Part 60 for the conduct of in situ testing at depth prior to submittal of a license application for construction authorization of a repository. Therefore, construction of an ESF will also facilitate the licensing process.

Jan 1, 1987

By R. Heikkilä

In this paper the utilisation of building information models (BIM) and construction automation on building sites is discussed. A lot of research has been carried out to develop new applications for using BIM to assist construction site planning, different operations and logistics. The methods of production control and management on site utilize BIM together with machine control and navigation systems. In Finland machine control systems and the automation of construction equipment is widely used in infrastructure construction. Recently similar methods have been introduced also in building construction. This paper describes some latest Finnish examples where BIM-software is used for the planning, execution and control of building construction operations. University of Oulu has studied methods and technologies to capitalize BIM-models. The research has been mainly in infrastructure construction but the activities have recently been extended to building construction. In this paper a BIM-based tower crane operation and control system is discussed as a case study. The aim of this study was to highlight the potential areas were automation can increase the crane productivity and improve site operations and logistics. The construction site managers and tower crane operators interviewed in this study were experienced in using BIM-models on site.

Aug 1, 2013

Occasionally it is interesting, and sometimes useful, to review the past for early references to our industry, and to learn of the trials and travail passed through before it arrived where it now is- and the results of such a review follow. Some time ago one of our modern playwrights and poets, Arthur Guiterman, turned to coal, with the following result: Afar in the Carboniferous time I grew in Paleozoical slime, A lepidodendron with boughs on my stem And lepidostrobuses grew out of them. My roots in the mud of the ages I spread And up to the heavens I vaunted my head, I throve in the heat of tropical sun, And now I am coal at two dollars a ton

Jan 1, 1939

By Mikko Ruonala, Pertti Lamberg, Olli Hyvärinen

The smelting of copper sulphide concentrate is the dominant route in copper production (Figure 1). Heap leaching of oxidized copper ores with weak sulphuric acid together with copper solvent extraction and electrowinning has gained popularity during recent decades, and it accounts for close to 20 % of primary copper production. Heap leaching offers advantages such as lower costs and consequently the construction of a production plant at a mine site is made possible. Limited resources of oxidized copper ores, the long leaching time of chalcopyrite and inability to recover gold inhibit this growth. The HydroCopperTM process developed by Outokumpu Technology at the laboratories of Outokumpu Research, Pori, Finland, is a new chloride leaching technology /1,2/, which offers an alternative to smelting and heap leaching (Figure 1). In the HydroCopperTM process sulphidic concentrates with various mineralogy and grade can be treated at the mine site to produce high-quality copper. Instead of copper cathodes the HydroCopperTM end products are copper wire rod, copper bars or copper billets. One of the advantages of HydroCopperTM technology is that gold can also be recovered in the process simultaneously /3/. To confirm the functioning of the new process and to dimension equipment Outokumpu Technology built the HydroCopperTM demonstration plant in Pori, Finland /4/. It has a capacity of 1 metric ton of copper per day. After testing with Pyhäsalmi copper concentrate in 2003, the first commercial demonstration run with Erdenet copper concentrate took place in 2004.

Jan 1, 2005

By E. Lee

Cone crushers are widely used within the mining and aggregate industries for the size reduction of minerals, ores, and rock materials. In mining applications for example, the product from cone crushers is often fed to HPGRs or directly to mills in the subsequent grinding circuit. An improved cone crusher performance can therefore result in an overall improved and more efficient comminution process. The objective of this paper is to systematically study a number of different ways of applying compressive crushing. By mathematically modelling these different crushing concepts and then theoretically optimizing crushing sequences accordingly, each concept can be studied and evaluated. In addition, aspects concerning whether or not the results are mechanically or practically achievable are considered. This study thus explores the advantages and disadvantages of different crushing concepts. In this paper, four different theoretical crushing concepts are presented and studied. The results show that in terms of interparticle crushing, optimal crushing sequences with varying compression ratios can be replaced by easier implemented series of constant compressions without significant deterioration. It is also shown that that considerably better performance is obtained for crushing sequences with both breakage modes. The subsequent comparison between such concepts indicates that different approaches can achieve the same results, and that the different concepts are comparable. It is further concluded that interparticle crushing should be kept to a minimum if fines generation or energy consumption is to be minimized, and that each of the studied concepts presents different challenges for implementation. Keywords: compressive crushing, cone crusher, optimization, modeling, crushing concept

Sep 1, 2012

By James S. Browning

In 1975 bituminous coal and lignite production in the United States reached an all-time high of 637 million tons, an increase of 6 percent over production in 1974. The output, valued at $11.9 billion f.o.b. mines, was produced at 5,100 mines in 24 states (6). Coal mining is the largest mining industry in Alabama. Production from Alabama's mines in 1975 was over 21 million tons, and present projections forecast a steady increase in production, with tonnages almost doubling by 1985 (5). Of the total quantity of coal produced, about 16 million tons were consumed in electric power generation and the remainder was used for metallurgical coke production, extraction of chemicals and petroleum based products, and power for industry. The fact that 75 percent of Alabama's power is generated by burning coal attests to the importance of this fossil fuel to the State. Approximately 14 million tons of coal were produced by strip-mining methods in Alabama during 1975 and about 7 million tons were produced by underground mining during the same period. Surface mining is expected to continue at about 14 million tons per year, but by 1980 underground coal mining is expected to increase to about 25 million tons (3). About 7 million tons of surface-mined coal in Alabama is subjected to some means of washing or cleaning. The methods used are screening accompanied by heavy media separation, jigging, tabling and flotation. Some of the simpler approaches employ screening and jigging, or tabling. Except where flotation is used, the screen undersize fraction (finer than 0.25 inch) is rejected, with the result that 10 to 15 percent of the coal is lost. Thus, in the State of Alabama an aggregate of about 1 million tons of coal is wasted annually in the fines which are impounded from treatment of surface-mined coal. The use of the Humphreys spiral to concentrate fine coal was practiced as early as 1947. At that time the Hudson Coal Company (1) used Humphreys spirals to concentrate anthracite fines. In 1950, the use of spirals to treat fine-size

Jan 1, 1977

By Reginald Dias

Mining operations take a tremendous toll on equipment, operating in difficult conditions day after day. Owners and operators cannot make the job any easier, but they can give their equipment an advantage. Equipment life may be extended through preventive maintenance and the proper application of quality lubricants. This means lubricants that are made to last longer and stand up better to the punishment mining equipment must endure. There are several practices to consider as part of a successful preventive maintenance program. A good place to start is to review original equipment manufacturer recommendations about servicing and maintenance intervals for each part of the equipment, especially the engine. If these recommendations have not been followed, owners and operators must begin periodic service work on equipment to help minimize equipment down-time and extend engine life.

Jan 1, 2003

By N Elith

Coal is a valuable energy source in New Zealand and has been mined from the West Coast for over 100 years. Stockton Mine is New Zealand's largest opencast coal producer supplying around 1.5 Mt of hard coking and thermal coal to international markets annually. The Stockton Plateau forms an extensive, gently inclined dip slope on erosion resistant Lower Eocene Brunner Coal Measures unconformably overlying basement rocks. The dip slope rises 600 - 1000 masl, locally dissected by fault scarps and present-day fluvial systems, some of which are deeply incised. Within the Mt Augustus Mining Block overburden comprises of a 30 - 40 m thick sequence of fluviatile, coarse to granular coal measure sandstones. High quality coking coal is preserved as a gently dipping, 10 - 12 m thick seam. High and sometimes very steep cliffs of jointed overburden shape the skyline escarpment, above steep forested slopes and gullies. As mining has progressed at Mt Augustus individual coal blocks are progressively becoming more technically challenging. This paper outlines the scientific approach taken by Solid Energy International and mining contractors to carefully unlock many thousands of tons of coal whilst protecting nearby flora and fauna from the impacts of dislodged rock and other blasting side-effects. The strategy involved: an expert-driven onsite risk assessment,formulation of a management plan to manage impacts,conducting an in situ vibration research program, andanalysis of results and operational designs to eliminate potential environmental problems.

Jan 1, 2003

By W. Ivanick, Frank W. Glaser

ORDERING reactions of Fe-Si compositions in the a region have been mentioned in a number of review articles.7-8 However, little is known in regard to the critical temperature, T at which this transformation takes place. Greiner and Stoughton,' in a study of the constitution of iron-rich Fe-Si alloys below 800°C, placed the onset of order at a composition of about 4 to 5 wt pct (7.5 to 9.5 atomic pct) Si. They observed that at this composition the ductility and strength begin to decrease sharply and brittleness develops. During X-ray studies they observed only the appearance of superlattice lines for compositions containing 12.5 atomic pct Si. More recent X-ray diffraction studies- etected the appearance of superstructure lines (corresponding to the calculated positions of [Ill] and [ZOO] reflections) for alloys containing 9.5 atomic pct. This fact confirms Greiner and Stoughton's original hypothesis in regard to the onset of order at compositions containing about 7.5 to 9.5 atomic pct Si. The physical properties.of Fe-Si alloys containing more than 10 atomic pct Si have been studied only to a limited extent. Their extreme brittleness and difficulties of sample preparation render them of little industrial use in comparison with alloys in the 0 to 10 atomic pct Si range. The properties of Fe-Si alloys reported to date are mostly properties measured at room temperature on ordered compositions It appears that because of experimental difficulties fully disordered alloys could not be produced in the critical composition ranges and their properties could therefore not be reported. In Figs. la, lb, and lc, a summary of physical properties of Fe-Si alloys, measured during recent investigations of the influence of silicon additions to iron, is presented. No mention of determination of the critical temperature, T for disorder could be found in the literature. The following is an account of work done in an attempt to: 1) produce the disordered state of various Fe-Si alloys and establish the critical temperature, T for disordering, and 2) compare the electrical and thermal conductivity characteristics of the ordered and disordered phases as functions of composition. Materials, Preparation of Test Samples, and Testing Methods Fe-Si alloys with high silicon contents (about 10 atomic pct) are usually prepared using powder metallurgy techniques. This method insures accurate compositions and high purity through the use of protective atmospheres during solid state diffusion alloying of the mixed powders."" Iron and silicon powders were mixed in the desired proportions, cold or hot pressed, and then homogenized at 1150°C for periods ranging from 6 to 12 hr under a protective getter and in a hydrogen atmosphere. Fully homogenized samples were quenched in water from various and successively higher temperatures to establish the critical temperature for disorder. Temperatures were determined using Pt—Pt-Rh thermocouples in contact with the test samples. Test bars were approximately 0.6x1.25x7.5 cm. Electrical measurements were made at room temperature by determining the potential drop over a 1.5 cm span for a current of 10 amp. Densities of the samples were determined by immersion. High temperature electrical resistivities were measured using previously described techniques.'" Specific heat conductivity up to 200°C was measured by heating one end of the test bar and water-cooling the other; heat conductivity was then obtained by subtracting the rate at which heat entered the water from the

Jan 1, 1957

By C. Anim-Sackey, R. K. Amankwah

Some large-scale mining companies in Ghana have adopted proactive management strategies in dealing with small-scale (galamsey) miners who have encroached on their concessions. This has been mainly achieved by ceding portions of the concessions held by the companies to the Minerals Commission of Ghana for licensing to the small-scale miners. This development has created an amicable relationship between the mining companies concerned and the galamsey miners in their host community. Ghana’s small-scale gold and diamond industry The small-scale gold and diamond mining industry in Ghana has existed for many centuries as an informal sector. Since the regularization of the activities of small-scale mining in 1989, two types of small-scale miners have emerged — legal and illegal.

Jan 1, 2004

By T. Ueda, T. Oki, S. Koyanaka

"Accurate assessment of the liberation state of crushed ore particles is important for efficient mineral processing. In general, the liberation state is assessed by two-dimensional (2D) measurement of polished ore sample sections. However, this 2D measurement inevitably suffers from overestimation of the degree of liberation, known as stereological bias. This arises from the fact that biphase particle sections of which only one phase happens to have been cut are indistinguishable from liberated particles. To date, several stereological correction methods have been proposed, but their applicability for various types of particles has not yet been sufficiently examined, and this tends to undermine their practicality. We have addressed this problem using a numerical-analytical approach in which various types of biphase particles are modeled, and the 2D sectional information is compared with actual three-dimensional (3D) information. Through simulations, we revealed a general relationship between the internal mineral structure of particles and the stereological bias. Finally, we have developed a unique stereological correction method in which the texture (a 2D pattern characteristic) of particle sections is used to estimate the internal structure of particles, and thereby the stereological bias. KEYWORDS Mineral liberation, stereological bias, texture analysis INTRODUCTION Mineral liberation assessment of 2D particle sections inevitably suffers from stereological bias; that is, overestimation of the degree of liberation. Stereological bias is caused by the fact that a composite particle can be misidentified as a liberated particle when only one phase happens to have been cut in sectional measurement. Stereological bias has attracted attention since Gaudin pointed out its importance in 1939 (Gaudin, 1939). Several attempts have been made to measure the 3D liberation state directly, avoiding the bias, using X-ray computed tomography (Gay and Morrison, 2006; Lin and Miller, 1996; Miller et al., 2003; Miller et al., 2009; Reyes et al., 2017; Videla et al., 2007). These have provided useful information through laboratory testing, but further technical refinement is necessary for practical usage, to overcome the technique’s limitations in terms of resolution, assessment of minerals of similar density, and speed. Therefore, for practical purposes, detailed information regarding mineral phase geometry is obtained by sectional analysis, using automated scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDX)-based analysis (e.g., with a mineral liberation analyzer (MLA) (Fandrich et al., 2007; Sandmann, 2015)); and the development of an effective method of stereological correction, which predicts the relevant bias and transforms the measurable 2D degree of liberation into its 3D counterpart, is an important research aim."

Jan 1, 2018

By L. R. Shoenberger

Boron has been used to produce nonaging low-carbon sheet steel. Retention of the necessary minimum amount of about 0.006 pet partially killed the steel. Amounts exceeding about 0.012 pet increased the degree of deoxidotion, piping tendencies, and possibility of hot tearing in primary rolling. Semikilled practice resulted in good ingot yields and satisfactory surface quality. Aluminum added with the boron provided a protective de-oxidizer. Good drawobility was indicated by performances of the steel in a limited number of deep-drawing trials. Some problems with hot-tearing and boron-analysis procedures were overcome. Metal lographically, the boron semikilled steels revealed some structures not usually found in plain low-carbon steels. IN 1943 Low and Gensamer1 reported that strain aging, which hardens and embrittles ordinary low-carbon rimmed steel, was due to nitrogen and carbon, and that oxygen played a relatively unimportant role. Since then, many investigators have substantiated their findings and indicated that nitrogen is particularly potent. Commercially, today's most widely produced non-aging sheet steels for deep drawing are either aluminum killed or vanadium rimmed types. The difference in deoxidation practice, alone, is evidence that oxygen is apparently not an important consideration in control of strain aging. The fact that nitrogen is important is apparent in the consideration that has been given, knowingly or unknowingly, to the amount combined with aluminum and vanadium. Patents were granted to Hayes and Griffis2 for the processing of aluminum-killed steel, and to Epstein" for the manufacture of vanadium rimmed material. Certain prescribed steps in producing these steels can be correlated with the formation of the respective nitrides within certain temperature ranges below the usual hot-finishing temperatures. The potential nonaging properties of either type can be reduced or suppressed by cooling too rapidly to permit the aluminum or vanadium to combine with nitrogen. Subsequent suberitical annealing of the cold-rolled strip, however, normally forms the nitrides and produces the resistance to strain aging. Titanium-killed nonaging steel, described by Comstock,1 forms a nitride in the molten state and is essentially nonaging throughout its processing. Zirconium-killed steel, which was investigated briefly by the author,* appeared to have similar nitride- forming characteristics. It is known" that chromium can produce nonaging rimmed steel, but relatively little is known of the potentialities of some of the other nitride-forming elements such as boron, silicon, columbium, and cerium. In attempting to develop a new nonaging cold-rolled sheet steel with good drawability, the following factors were considered pertinent. Such a steel would necessarily have a low carbon content and therefore have a relatively high degree of oxidation when made in a basic open-hearth furnace. If the denitriding element were also a deoxidizer, a part of the addition would be lost as oxide. The degree of deoxidation would determine whether the steel is rimmed, semikilled or killed, and also could be expected to have an important bearing on ingot yields and ultimate surface quality. Assuming that the pattern for the production of cold-rolled sheets would not be changed to any great extent, the nitride must form in the molten steel, in hot rolling, in subsequent cooling, or in annealing. The nitride, once formed, should resist dissociation and be stable in the final product. Usually an excess of the nitride-forming element is required to combine with sufficient nitrogen. If the element used is a strong ferrite strengthener, a small excess may markedly decrease drawability. With aluminum and vanadium, about 0.03 to 0.05 pct in the steel is preferred. Epstein has said" that about 0.30 pct chromium is required. Titanium nonaging steels are hard unless a sufficient amount (about 0.30 pct) is added also to combine with the carbon. The cost of the necessary amounts of these latter two elements discourages commercial acceptance. Silicon was considered as a possible nitride former, but since amounts up to 0.10 pct in rimmed and semikilled steels do not induce marked resistance to strain aging, larger amounts are apparently required, which would tend to harden and strengthen the ferrite. Of the other elements mentioned, all but boron are expensive heavy-metal elements. Stoichi-ometrically, almost an equal weight of boron would be required to combine with the nitrogen—-ordinarily about 0.003 to 0.006 pct in scrap-practice open-hearth steels. Boron is a slightly stronger deoxidizer than carbon but is less powerful than zirconium, aluminum, or titanium. Thus a rimmed-steel practice might be possible. There is much in the technical literature concerning the hardenability effects of minute amounts of boron in killed steels but very little about its behavior in low-carbon material—particularly as a ferrite strengthener. The available data indicated a need for better information concerning the effects of boron in low-carbon strip steels. Experimental Work Development of a Boron-Treated Nonaging Strip Steel—Initial attempts to produce a boron-rimmed strip steel employed 3-ton basic open-hearth heats which could be teemed into molds large enough to sustain a normal rimming action. Boron as ferro-boron was added to the ladle in small amounts because of the reported hot-short character of aluminum-killed heat-treating grades containing more than about 0.005 pct boron. Actually, the amounts used, i.e., 1/8 and 1/4 lb per ton, would be large for

Jan 1, 1959