Search Documents

By M. B. McClenaghan

"This paper summarizes diamond exploration techniques used in glaciated terrain, focussing on indicator mineral and geochemical methods applied to glacial sediments. Understanding the ice flow history, depositional history, and stratigraphy of glacial sediments is essential to successful sampling, interpretation and follow-up of indicator mineral and geochemical anomalies related to kimberlites. Kimberlite indicator minerals survive glacial transport over long distances and the relative abundance of each mineral in till is a function of the primary mineralogy of individual kimberlites. Indicator mineral distributions observed at a regional scale define the net effect of glacial dispersal, often along different ice flow directions. Local-scale distributions define individual dispersal trains. The medium sand (0.25 mm to 0.5 mm) fraction of heavy mineral concentrates, * GSC Contribution No. 2002028 prepared from glacial sediment samples, is best suited for indicator mineral surveys. The application of till geochemistry to diamond exploration is increasing because it is significantly cheaper than indicator mineral analysis and it can be performed quickly. The <0.063 mm (silt+clay) and 0.5 mm to 2.0 mm (coarse sand) fractions provide the best geochemical contrast between background and kimberlite-rich till. Kimberlite pathfinder elements that provide good contrast include Ni, Cr, Ba, Co, Sr, Rb, Nb, Mg, Ta, Ca, Fe, K, Ti and LREE, the relative importance of which will depend on kimberlite composition and that of the surrounding bedrock.IntroductionIn Canada, glacial erosion is the principal means by which kimberlite and its associated minerals have been dispersed, from a few tens of metres to tens of kilometres down-ice. Post-glacial weathering has had little impact on kimberlite debris in the glacial sediments, thus boulder tracing, indicator mineral methods and trace element geochemistry of the fine fraction of till (“drift prospecting” methods) can be used to detect kimberlite dispersal within areas covered by glacial sediment. This paper provides a summary of drift prospecting methods for kimberlite exploration in glaciated terrain, and includes examples of reconnaissance- , regional- and local-scale kimberlite indicator mineral and till geochemical distribution patterns.Weathered kimberlite is more susceptible to glacial erosion than the surrounding bedrock, thus many kimberlites in glaciated terrain are found in low or swampy ground, under small lakes, or covered by thin (< 1 m) to thick (>50 m) glacial sediments. Glacial erosion has removed varying amounts of the pre-glacially weathered kimberlite and, in some cases, the hard competent kimberlite below. For example, glacial erosion of the Peddie, McLean and Seed kimberlites near Lake Timiskaming, Ontario, removed pre-glacially weathered kimberlite, leaving a polished striated subcropping surface (McClenaghan et al., 1999a). In contrast, glacial erosion of the B30 kimberlite, near Kirkland Lake, Ontario (Fig.1), was much less vigorous and left a >10 m cap of soft and highly weathered dark green clay-rich kimberlite (McClenaghan et al., 1996). The thickness of remaining pre-glacially weathered kimberlite will influence the geophysical signature of the kimberlite."

Jan 1, 2002

By K. Peake, A. Dalvi, V. Hernandez, S. Chang, M. Oliazadeh

"Ironstone Resources Ltd. is developing the Clear Hills oolitic iron ore deposit in northwest Alberta, Canada. Sources of oolitic iron ore worldwide are abundant and ubiquitous, but there is currently no commercial technology to extract iron from oolitic iron ores. Mineral processing of the ore to generate a commercial iron ore concentrate is very challenging due to the nature of these ores. Accordingly, Hatch and Ironstone are developing a new pyrometallurgical process (Hatch Ironstone Chloride Segregation) to produce metallic iron from high silica and high phosphorus oolitic iron ores. Following the chloride segregation process, the treated ore is subjected to fine grinding. The iron is then separated by magnetic separation. The iron grade and phosphorus content of the final product shows a strong dependence on the separation methodology and the grind size. The pyrometallurgical process has been developed and tested at a lab-scale pilot plant. The commercialization of this technology could provide an opportunity for the development of a new alternate iron making technology. This paper presents the results of test work done on the raw iron ore to create a concentrate and also on the products of the pyrometallurgical process for the production of a high grade 90% metallic iron product.INTRODUCTION Oolite is a sedimentary rock formed from ooids – spherical particles with concentric layers. There are a number of large oolitic iron deposits where the mineralogical form features a low iron content and high concentration of impurities making them presently impossible to exploit on either a technical or economic basis. The fifteen largest oolitic iron ore deposits in the world are estimated to contain approximately 337 billion tonnes of iron ore, which would be a significant source of supply for worldwide steel production. A viable process that can economically recover iron from these oolitic iron ore deposits could become an important new technology to meet future demand in the steel industry. Hatch and Ironstone have demonstrated that oolitic iron ores can be exploited to produce direct reduced iron (DRI). Direct reduction ironmaking is a method for producing solid metallic iron using different techniques compared to the blast furnace process, which is the more conventional ironmaking route. The demand for the construction of direct reduction ironmaking plants has increased in response to the increasing demand for crude steel. It is viewed as a method of providing low-residual iron sources to scrap-based steelmaking in electric arc furnaces."

Jan 1, 2014

By M. Dobbins

Magnetic separation has long been used to upgrade and beneficiate a wide variety of industrial minerals. Advances in both wet and dry magnetic separators over the years has broadened their use, and questions are often raised about which separation technique or equipment type is most appropriate for a particular operation. This paper will provide a brief look at existing magnetic separation technologies, and discuss their potential advantages and disadvantages when applied to heavy mineral applications. Relevant case studies for the separation of ilmenite and chromite are then presented. The process development efforts undertaken for each case are described, and the rationale for selecting appropriate magnetic separation technology is explained. The nature of the material being treated must clearly be understood, knowledge and access to testing the best separation technologies is required, and careful process development and economic evaluations are a must. As is shown in the case study discussions, it is imperative that these principles drive the separation technology selection and placement, rather than looking at typical or existing similar flowsheets as rules. As examples, the ilmenite tailings case study presented in this paper shows how advances in technology have allowed for increased recovery of -45 µm ilmenite by utilizing a multi-stage SLon® wet magnetic separator circuit equating to an additional 30 000 tons of ilmenite produced per year. The virgin chromite case study presented shows that through careful testing and circuit design efforts using RED technology, a 20% increase in overall chromite recovery was achieved over previous demonstration work.

Jan 1, 2007

By Nicholas J. Grant, Chih-Chung Wang

TO phase of the Ti-0 system has the structure of NaCl and has a wide range of solid solubility.&apos; In the course of studying the Ti-Cr-0 ternary system, binary alloys were made of iodide titanium and high purity TiO,. It was found from X-ray studies of the binary alloys that a transformation of the TiO appears to take place at a temperature near 925°C. Evidence of this phase change is best seen in Fig. 1. Fig. 1A shows the X-ray spectrometer pattern (CUKa radiation) of an alloy of 25 wt pct 0 corresponding to the stoichiometric composition of TiO.

Jan 1, 1957

By Bryan C. Field

The proposed construction schedule for the St. Anthony Falls I-35W Bride challenged the abilities of the design-build teams to utilize the best and most efficient methods to meet Minnesota Department of Transportation?s deadlines and design requirements to restore traffic to the Interstate 35W crossing of the Mississippi River, along with a sense of normalcy, following the bridge collapse. The project team ultimately designed and constructed two foundation systems at various substructures for bridge support. Steel H-section piles were driven to bedrock for south bridge abutment support and drilled shafts were used for the north bridge abutment and piers for the Mississippi River Bridge. Drilled shafts we also used for the abutments for the three single span bridges carrying I-35W over 2nd Street. The design-build team used high-strain dynamic pile testing with a Pile Driving Analyzer (PDA) to verify H-Pile capacities and performed drilled shaft inspection on a 24-hour basis during installation over the winter months. The drilled shaft inspection process was a vital part of the project quality control program to maintain the necessary methods for proper drilled shaft installation. Ultimately, with an efficient design, quality construction methods and operation, and a rigorous inspection and quality control plan; the I-35W Bridge was opened to traffic 3 months ahead of the already accelerated schedule.

Jan 1, 2009

By Cam Thomas, Steve Bernard

Various types of blasting instrumentation can be used in the field to analyze conditions before, during and after a blast, and to indicate what changes need to be made. When different types of measurements are combined together, the blaster can end up with useful data that can pinpoint the source or sources of problems and what changes have to be made. This paper outlines two case examples where blasting instrumentation was used to overcome problems in separate quarry operations. Extensive measurements with different systems led to significantly improved blasting results.

Jan 1, 2012

By K. R. Dorman

To further investigate the potential of precast concrete sets as a support medium for underground mines, the Bureau of Mines designed a five-piece precast concrete drift set for a small opening and tested it to destruction in a straining frame. Twenty-seven tests were made with three sizes of members using three loading conditions. In addition, six tests were made with sets in a distorted configuration, Test results and typical failure patterns are presented. A comparison of results with those previously reported for the three-piece set shows the five-piece set supports considerably larger total loads than does the three-piece set of equivalent cross section designed for the same size of opening. Recommendations are made for improvements in design.

Jan 1, 1969

By R. E. Cole, A. M. Gaudin

OLEIC acid, a standard flotation reagent, has generally been preferred to other fatty acids. Because oleic acid differs from saturated fatty acids by the presence of one carbon-to-carbon double bond and because the flotation operation is one in which extremely intimate exposure of the reagent to oxygen is obtained, it appeared possible that the value of oleic acid as a flotation collector was related to the oxidizability of its double bond. To test this hypothesis, the floated mineral, fluor-ite, was leached with a solvent capable of extracting the adsorbed reagent and the extract was analyzed.&apos; Results show that oleic acid is not oxidized during flotation, although some oxidation can be obtained if the flotation operation is repeated many times and if oxygen in place of air is employed as the gas during flotation. Incidentally, it was found that lino-leic acid which has two nonconjugated double bonds is not affected appreciably more than oleic acid. Linolenic acid which has three nonconjugated double bonds is measurably altered even during one flotation step, using air. The fatty acids used, from the Hormel Foundation, were of the highest purity. The quantity of fatty acids employed in each test was sufficient to float the mineral, but less than the theoretical amount required to form a monolayer at the mineral surface. The purpose of this limitation was to eliminate droplets of oil smeared on the adsorbate-covered mineral surface. The mineral was dried in vacuum at about 60 °C. Effective leaching was obtained by use of a solution of 1 pct hydrochloric acid in absolute alcohol. The extract was separated from the solvent by distillation, with final recovery of the extract in carbon tetrachloride. The identity of the extract was tested by a combination of analytical procedures including infrared spectroscopy, saponification number, iodine number, and index of refraction. At the outset, great hopes for accurate quantification of oleic acid oxidation had been entertained in regard to the method of infra-red spectroscopy. Unfortunately, because the double bond in the oleic acid is so sym- metrically located at the center of the molecule that it provides very weak absorption bands, accurate quantitative analyses were not obtained. Nevertheless, infra-red spectrograms suggested the absence of double-bond oxidation during flotation. Iodine number, semi-micro method, provided a critical test of the extent to which fatty acids oxidized during flotation, see Table I. The index of refraction was used in a qualitative rather than quantitative fashion, and its findings corroborated those obtained by the iodine-number method. It is concluded, in the case of fluorite and C-18 fatty acids having one or two nonconjugated double bonds, that there is practically no change of the fatty acid molecule or ion during the flotation operation. It would appear, therefore, that the extraordinary utility of these reagents is related to some property of the compounds other than the oxidizability of their double bonds. Acknowledgment The research reported herewith was sponsored by the Research Division, U. S. Atomic Energy Commission, and for this help the authors express their appreciation. Reference &apos;R. E. Cole: "Double-Bond Reactivity of Oleic Acid During Flotation." Thesis submitted in partial fulfillment of the requirements for the degree of M.S. at the Massachusetts Institute of Technology.

Jan 1, 1954

By Christian Wawrzyniak

An analysis method for modeling compensation grouting based on the finite element method is presented. By this method the design parameters of compensation grouting, grouting pressure and grouting volume, can be evaluated. Also the subsidence of a building due to tunnel driving as well as the lifting of the building by compensation grouting can be simulated. The stress changes in the tunnel lining and in the foundation of the building are computed as well. The application of the analysis method is demonstrated on two examples for compensation grouting in combination with construction of tunnels.

By D. A. Schemnitz, O. W. Ellis

Certain alloys1 that, as a result of quenching, are retained in the form of homoaeneous solid solution are known to increase in hardness and strength on standing at room temperature or on heating at slightly elevated temperatures. Other alloys2 that, on rapid cooling, are held in the form of homogeneous solid solution, as, for example, certain steels, behave in like manner on heating to somewhat higher temperatures. The observed increase in the hardness and strength of these alloys, referred to as " aging"&apos; or as "secondary hardness," is widely accepted as being occasioned, either in whole or in part, by the precipitation in submicroscopic form of such constituents as were held in supersaturated solid solution as a result of cooling in excess of a certain critical rate. In earlier discussions of the cause of age hardening or secondary hardness, the question of the hardness of the precipitated particles does not appear to have been raised. At present, however, the general opinion appears to be that age hardening and secondary hardness are occasioned by the precipitation of hard particles within the supersaturated solid substance.3 The authors may be wrong in their belief that the last is a prevailing opinion. Nevertheless, it is thought that the following experiments,

Jan 1, 1925

By Russell R. Trengove

The Strawberry tungsten mine is in the Jackass Mining District, in an isolated portion of eastern Madera County, near the southeast corner of the Yosemite National Park. The deposit was discovered in 1941, and production started in 1943 when the mill was completed. With the exception of 1946 and 1947, production has been continuous. The area in the vicinity of the mine is granite containing islands of sedimentary beds highly altered by metamorphism that resulted from the intrusion of acid igneous rock. Schoelite occurs in almost vertical lenses of tactite between the limestone and the granite.

Jan 1, 1949

By M. Arnesen

Mining professionals recognize the need to continuously evaluate and refine mine planning standards and scheduling. We must examine our current reality, and evaluate the following: •How well do our planning standards represent the actual mining process? •To what extent do they support the requirements of the downstream mining activities? •How we apply them to operational management and control? In most operations, mine-planning standards are global averages. Little differentiation is madein quantifying key planning variables. Often standards used in the long-term, are applied to the short-term, and the standards and scheduling precedents are only reviewed occasionally. Mine-planning standards applied to production schedules are often only focused on the management of functional mining performance, and play no role in managing the requirements of down stream processing. Many mining operations are characterized by high levels of fluctuation, and typically incorporate a wide range of factors and adjustments to compensate for deviations from performance targets, in mining operations as well as for the other business areas. The reason for using global averages is because of a lack of understanding of the causes of deviations that occur through the process, and the impact that they may have on the performance of the business as a whole. Average standards and factors are often used to quantify the variability in a system. From these average values, measurement standards and performance targets are derived for the planning and execution environments. During the execution of a plan/schedule there will be deviation in actual performance and the planned ‘average’ standards. In reality the ‘average’ conditions seldom occur and the impact of variability and interdependency are seldom constant or predictable. The predictability of variability and interdependency is further complicated by the fact that mining conditions have a role to play in the actual production performance, and they too are variable. By developing the throughput knowledge of our production systems, we can better understand the nature of variability and the interdependency within the systems as well as the impact of interdependency between the links in our production chains. With this knowledge, planning standards and scheduling precedents can be better defined and sensibly differentiated. This will improve planning and management of ore utilization, mining production and the effectiveness of processing. As a result the business will be more stable and predictable and business performance will be improved. The purpose of this paper is to describe: •At a high level, the scope for refining and differentiation in mine planning standards, and incorporating geological and plant parameters into mine scheduling. This will improve planning and scheduling and the overall performance of the mine. Given our current level of scientific knowledge and the technological tools at our disposal we should be able to plan and schedule production so that we can manage pro-actively and improve business performance. In doing so we can also improve reconciliation and value tracking through mining and processing •The flexibility and functionality of the XPAC planning and scheduling tool that will enable a throughput management approach.

Jan 1, 2003

By Philip J. Guerney, S. O’ Leary, André R. Laplante

"Concentration of dense mineral phases (s.g. greater than 7) for characterisation of individual particles and mineral grains by electron microscopy is a well established technique for the detection and characterisation of valuable mineral phases. This presentation describes the type of data that can be generated when both the concentration and characterisation steps are carried to higher levels than typical. The concentration step is the gravity recoverable gold (GRG) protocol that has been used for over 100 ore samples. This protocol yields three concentrates that represent three progressive degrees of grinding and liberation. Three ore samples were subjected to the GRG protocol and three size classes of each concentrate were characterised using the mineral liberation analyser (MLA), an automated, EDX-based tool. This presentation briefly presents GRG and MLA technology, and then focuses on the results obtained: photos, images and databank, the latter used to evaluate the extent of particle liberation and particle shape.INTRODUCTIONThe practice of gravity concentration prior to characterization of mineral samples using electron beam microscopy is solidly established. Typically, a dense liquid such as tetrabromoethane (density: 2.97 g/cm3) is used to reject the light phase, typically carbonates and silicates. The heavy phase, mostly sulphides, oxides and precious metals, is then mounted in a polymer matrix and examined using beam microscopy.Both the pre-concentration and the sample preparation/examination steps have seen significant advances over the past ten years, but are not without problems. A major issue of preconcentration is that most dense liquids used are toxic, tetrabromoethane being a prime example. More recently, a dense liquid with little or no toxicity (sodium polytungstate, distributed by Sometu Inc.) has become commercially available, but its use is limited to relatively low s.g. splits around 3 g/cm3. Dense liquids are viscous, and their use is limited to particles coarser than 37 µm, although centrifuge separation can probably lower this limit to around 10 µm. Magnetogravimetric separators can achieve much higher specific density cuts, but upgrading below 100 µm or in the presence of magnetic minerals remains a problem. The use of centrifuge separators such as the 3-in Knelson Concentrator (KC MD3) or the Falcon 4-in SB (SB4) is particularly attractive since these units can easily process large masses (by laboratory standards) and achieve a cut density well above those of dense liquids."

Jan 1, 2003

By George H. Tousley

As a member of the vast fraternity of those that supply and service the mining industry, I can assure you that we are amused, amazed, and horrified at the poor drilling and blasting practices of a great number of operations. Yes, ?horrified?. After all, that is our product you are using and abusing. We all know that drilling and blasting is expensive. In some operations D & B costs may exceed excavating or hauling costs, or both. At any rate, it is the only portion of the whole operation that could be said to directly affect other costs. There is no argument that it affects excavating costs. If the overburden and/or product is drilled and hauled, it affects haulage costs. It can easily affect milling costs, if more or less fines is important. And poor fragmentation affects crushing costs. If scalping is done ahead of the primary crusher it can affect production. As has been pointed out, the D & B operation itself is costly, and therefore should lend itself to close scrutiny. Anyone that could immediately decrease haulage costs by 10% would be a hero with any mining company.

Jan 1, 1976

The kinetic and practical aspects of the extraction of copper from copper-rich solutions by cementation on iron was investigated. Tests were made on the effect of stirring speed, cupric sulphate concentration, acid concentration, temperature, and ferric sulphate concentration on the reaction rate and excess iron consumption.Most kinetic investigations were conducted under a nitrogen atmosphere to prevent any oxidation of the iron or copper metals. The stirring mechanism for all tests incorporated the use of a rotating impeller above a static disc in the solution. The activation energy for cementation on the steel disc at high stirring speed was 8&#183;6 kcal/mole, indicating a predominant chemical control.Increasing the pH first decreased, then above pH 3, increased the reaction rate. Additions of sodium sulphate also significantly increased the reaction rate.The use of high temperature and high pH under an inert atmosphere has been suggested for increasing the reaction rate and producing a high purity sponge copper product.

Jan 1, 1972

By Raymond Franz

Of the many types of capital equipment found in a surface operation, draglines and mining shovels are probably subjected to the most severe service. Yet, some excavators have seen a generation or more of continuous service-proof, if any is needed, of their ruggedness. To keep these expensive pieces of machinery operating, a continuing maintenance program which includes field weld repairs is essential. During an excavator&apos;s working life, minor cracks may appear in parts of the steel structure, caused by fatigue and sometimes material defects-defects so small they could not be detected during manufacture.

Jan 6, 1978

By Lachezar Tsotsorkov

Corporate social responsibility Is a principal trend of the corporate strategy for sustainable development of Assarel-Medet JSC ? the largest Bulgarian company for open pit mining and ore processing the production activities of which date back to 1964. Sustainable development Social responsibility is considered as one of the three pillars for sustainable development, together with the economic and environmental responsibility.

Aug 1, 2013

By R. L. King

This report describes a method for designing and constructing ground beds that has been developed under the sponsorship of the Bureau of Mines. The procedures for designing and constructing a driven-rod ground bed with a resistance of 5 ohms or less are given. Some of the theory of soil resistivity and fall-of-potential resistance measurements is included. Results of a bed constructed at the Bureau of Mines mine car roadway are presented.

Jan 1, 1978

By James T. Skoch

With the ongoing pressure on the secondary aluminum business to limit the amount of waste generated from processing aluminum dross, it becomes very advantageous to preprocess the dross to reduce waste. The advantage of preprocessing is that it significantly reduces the oxides and salt cake generated when melted. Various products can be produced from the oxides for the steel industry. The following paper will demonstrate that removal of oxide fines before melting will result in large volumes of material not being landfilled. We will show that the end result of this technology is to significantly reduce the amount of salt cake sent to a landfill while maximizing the recyclability of the aluminum dross.

Jan 1, 1995

By J. N. Van der Merwe

"A major shortcoming of the statistical back-analysis of coal pillar strength is that it relies on the asmined pillar dimensions, not taking into account time-related pillar scaling with subsequent reduction in pillar width. The paper describes an investigation where the rate of pillar scaling was applied to the pillars in the databases of failed and unfailed pillars. The reduced pillar sizes were then used in the same method of statistical back-analysis that had been used in the past.This resulted in an equation for pillar strength which predicts significantly greater pillar strength than the previous statistical analyses, which is similar to the strength which had been found earlier by direct testing of large specimens underground. It is concluded that the lower strengths found by previous statistical analyses are due to the incorrect pillar width being used and that by adjusting the pillar sizes to compensate for scaling, more credible results that correspond to direct testing are obtained.As the newly derived strength equation is time-dependent, it follows that the safety factors and probabilities of failure are likewise time-dependant. An equation to determine the probability of failure is also developed. This results in the safety factor being close to unity at a probability of failure of 50%, which is aligned to statistical expectation. IntroductionSince the Coalbrook mine disaster, caused by massive pillar collapse, there have been several attempts at analysing and defining the strength of coal pillars. It was realized in the very beginning that performing classical strength tests on coal specimens in a laboratory and then transferring those results to real coal pillars could not be successful. The scatter of results is one problem and, more seriously, there is a size effect (at least for small specimens) that made the transformation of strength results to much larger coal pillars underground all but impossible.Two main schools of thought then emerged. Some researchers preferred to perform direct strength tests on large specimens underground, while others relied on statistical back-analysis of failed and unfailed pillar cases, attempting to determine the differences in size and shape that would allow a satisfactory prediction of failure. The latter school of thought resulted in the method that was widely accepted by the South African coal mining industry, described in the landmark publication by Salamon and Munro (1967)."

Jul 1, 2019