Search Documents

By W Newns

This paper describes laboratory and in situ tests and determines a set of parameters for stiffness and strength properties for a weak sedimentary rock mass, the East Coast Bays Formation of Auckland. The parameters derived are discussed in relation to peak strength and in respect of deformation limits associated with sequential excavate and support (SEM) or conventional tunnelling.

Mar 8, 2011

By K. Moxham, R. G. B. Pickering

Over the last few years Lonmin Platinum and Sandvik have embarked on a unique partnership of collaboration through a systematic approach to developing equipment to mechanize and automate narrow reef platinum mining. After the initial design and manufacture of the equipment the key aspect is the integrating equipment, people and method into a mining system. Another key a spec of mechanization is the optimization of equipment utilization and this philosophy has ensured continual evolvement of mining methods. This paper describes the trials and development that have resulted in the mining method described as Lonmin mechanized breast.

Jan 1, 2006

By David Deglon, Martin Harris, Mehdi Safari

This paper investigates the effect of energy input on the flotation of galena in a novel oscillating grid flotation cell (OGC). Oscillating grids generate near ideal hydrodynamic environments, characterised by turbulence which is relatively homogeneous and isotropic. Previous work was limited to quartz (-100 µm). Galena (-150 µm) was floated in the OGC at power intensities from 0.5 to 3 W/kg using 0.13, 0.58 and 0.82 mm mean bubble sizes (d10) and at three collector dosages. Results show that the effect of power intensity on flotation kinetics is strongly dependent on both particle and bubble size. For fine particles (-19 µm), increasing energy input increases the flotation rate at a low collector dosage but leads to an optimum at both the moderate and high collector dosages. For intermediate particles (+19-38 µm), increasing energy input has no effect on the flotation rate at the low collector dosage but leads to an optimum at both moderate and high collector dosages. For coarse particles (+38-150 µm), increasing energy input has no effect on the flotation rate at the low collector dosage and leads to a general decrease at both moderate and high collector dosages. Optimum conditions for fine particles are using small bubbles at a moderate collector dosage and an energy input of around 2 W/kg. Optimum conditions for moderate particles are using small bubbles at a high collector dosage and energy inputs of around 1.0 W/kg. Coarse particles do not benefit from agitation.

Jan 1, 2014

By Sano S, Ishikawa T, Nagaoka H, Hayashi Y, Hasegawa M

The stirred mill is regarded as one of the most efficient devices for micronising materials and has come to be actively used for preparation of fine particles. Recently, the demand for ultrafine particles was increased in many kinds of industries. In this paper, autogenous grinding to get submicron particles based on mutual friction feed material has been carried out using a stirred mill. The mill used was made of stainless steel and its volume was about 5.5 litres, and has 12 impeller blades. Sample used was limestone. In the present work, two operating parameters such as stirring speed and feed size of limestone were considered. The ground products were sieved in the size range from feed size to 325 mesh (45 lun), and from 45 to 0.17 pm the size distributions were measured by a laser diffraction and scattering method. The progress of grinding was evaluated by the increasing amount of submicron particles in products. As a result, the rotational speed of impeller with the minimum energy consumption to produce submicron particles was observed. It was found that the autogenous grinding with a stirred mill is an effective method for producing submicronized limestone.

Jan 1, 1993

Between 1993 and 2003, a series of AG and SAG mill pilot plant trials were conducted using Hardinge Ical pilot plant scale SAG mills on numerous ore samples and ranging across a wide variety of operating conditions. The data from these tests were used to evaluate the design of SAG and AG mill circuits for over a dozen projects, of which about half were eventually constructed and commissioned. The data were also used in the development of SAG mill modelling, scale-up and simulation procedures by several consultants who had access to part of the data set. Recently, we have had the opportunity to bring this data together and further analyse the consolidated dataset. This paper reports on the outcomes of this analysis that has identified the impacts of different AG/SAG circuit flowsheets and operating conditions on energy efficiency and operating cost.

Jan 1, 2012

By M Scoble, W S. Dunbar

This paper reviews methods for grade estimation in short-term mine planning for block caving. Two particular tools are used: Ordinary Kriging and Simple Kriging with moving averages. It is also considered the influence of draw characteristics on the grade estimation process. Reference is made to mine case study data and analysis. These demonstrate that operational grade estimation is not a trivial process. It must take into consideration: the grade variability (in terms of ore and dilution), sampling interval, geological and geotechnical characteristics, geometrical layout and draw characteristics. Significant improvements appear possible in short-term planning if variogram analysis, as well as kriging methodologies, are introduced into the operational grade estimation process.

Jan 1, 2000

By Michael Tenebaum, C. C. Brown

In recent years, the importance of slag control in basic open-hearth operations has been universally recognized. To effect such control during the working period of the heat, methods have been developed to measure or estimate slag oxidation and slag basicity. While satisfactory rapid chemical methods have been developed to determine slag oxidation, no completely adequate method of evaluating basicity has yet been provided. The most generally accepted control methods of measuring slag basicity are based on visual cstimates. While considerable benefit may be derived from such estimates, the need for some measurable indication of slag basicity has become increasingly apparent. In a recent paper, Philbrook and Jolly suggested a promising technique for making the basicity determination. Their method consists of measuring the pH of a mixture of powdered open-hearth slag and distilled water. It was found that a relation could be established between the slag basicity and the alkalinity of the water mixture as measured by the hydrogen-ion concentration. The general procedure followed in making the measurements and the considerations involved in constructing the original curves are given in the paper of Philbrook and Jolly and need not be repeated. It is the purpose of this paper to discuss some of the factors considered in applying the pH measurements to actual slag control and to present some of the results of its apphcation. Factors Involved in Measuring pH of Water-slag Mixtures To facilitate the application of the pH control system, it was desirable that no alteration be made in the routine methods of sampling and crushing the furnace slag. Some of the factors considered before establishing a curve to relate slag basicity with the pH reading arc reviewed individually in the following paragraphs. Effect of Cooling Rate Under actual operating conditions there can be considerable variation in the temperature of the piece of slag crushed for the pH determination. To determine whether variations in crushing temperature or in cooling rate would affect the pH reading, a series of four samples was prepared from each of two separate slags. These samples represented conditions far more extreme than would actually be encountered. To obtain these samples, a thick pancake of slag was poured. One piece of this pancake was crushed immediately after it had solidified. Another piece was water-quenched and then crushed. A third piece was allowed to air-cool to room temperature before crushing. The fourth sample was prepared from a chilled slag. This sample was poured onto a heavy inclined steel plate at the

Jan 1, 1945

By A. Kogelbauer, A. Stadtschnitzer, A. Boehm, F. Schillab

"The paper covers the design and implementation of an industrial dense medium cyclone plant for carbonaceous iron ore, the proving of efficiency as well as the development of a predictive model for plant control. The VA Erzberg GmbH mines about 12 Mio.t of carbonaceous rock ore at the “Steirische Erzberg”. Due to increased demand of the Austrian steel plants, the production of ore concentrate was raised by 30 % up to 3.0 Mio t/a during the last 5 years. One of the projects to realize the increase in capacity at improved concentrate quality was the implementation of a dense medium cyclone plant for the fine size fraction – 8 +1 mm replacing the former dry permanent magnetic drum separators. By physical separation the siderite variety “spateisenstein” (42% Fe) of a density of 3,8 g/cm³ is separated from ankerite (10 – 17% Fe), the second iron bearing carbonate with a density of 3,2 g/cm³, dolomite, calcite and silicate bearing schists. The feasibility of the process was proven by the test results obtained from a test rig, that was constructed and operated in close cooperation between the Chair of Mineral Processing, Montanuniversitaet Leoben and VA Erzberg GmbH. The density separation surpassed the efficiency of magnetic separation clearly shown by •- values. The plant performance tests (capacity 120 t/h) verify the cut densities defined by Tromp T50 -values and the assigned efficiency found in the pilot tests at varied settings of media density, pressure drop, cone angle and apex diameter. The test rig as well as the final process will be presented. In order to create a tool to predict the performance of the DMS in the centrifugal field at various settings for varying feed composition the experimental results from size and density testing are analyzed in a modified way to obtain physically justified, smooth approximations for the performance curves. Models developed on coal washing plants are checked for their validity at increased densities."

Jan 1, 2018

At the meeting of the Board of Directors the following resolution was passed: "The members of the Board of Directors of the American Institute of Mining Engineers desire: to place on record their appreciation of the very great generosity of one of their colleagues and a member of the Board, George D. Barron, expressed in his gift of $5000 to relieve the financial stringency caused by the unusual expenditures of the Institute for war work and the remission of dues of those members on active service." By-Law VIII. was amended to make a slight change in District No. 5. The report of the Auditing Committee was accepted. Tellers were appointed to: count the ballots on officers and on the proposed amendment. The proposed budget for the year 1919 was presented. The following resolution re Secretary Emeritus Rossiter W. Raymond, which had been prepared, by request, by Dr. A. R. Ledoux was then unanimously adopted. "The Board of Directors of the American Institute of Mining Engineers would place upon its minutes its profound sense of loss and sorrow in the death of Rossiter Worthington Raymond, Ph. D., LL. D., Secretary Emeritus of the Institute. Both as one of its founders and as its Sec-retary for 27 years, his was the guiding spirit of the Institute for more than a generation. "During the greater part of this long period, it might almost have been said that the Institute was Dr. Raymond-and Dr. Raymond the Institute. When with the progress of growth and development, great changes were introduced, Dr. Raymond acquiesced in these in spite of some misgivings, such as those with which a father might contemplate the emergence of his child from the careful supervision of the home; but as Secretary Emeritus for the past eight years, lie was always ready with valuable advice and helpful suggestion.

Jan 3, 1919

By R. Dugdale, F. Habashi

Studies on hand-picked samples of chrysocolla from Arizona showed that heating in an inert atmosphere enhances greatly copper extraction by ammoniacal-ammonium carbonate solutions. Heating in hydrogen improves the extraction of copper even further and maximum extraction by ammoniacal-ammonium carbonate and by sodium cyanide solutions is achieved for samples heated at 350°C. Heating in SO2 atmosphere results in the simultaneous formation of CuSO4 and Cu2O; maximum reaction rate is also achieved at 350°C. At temperatures higher than 350°C, CuCO4 starts to decompose. Chrysocolla heated above 600°C either in argon, H2, or SO2, is rendered less amenable to leaching, supposedly due to the formation of insoluble copper silicates.

Jan 1, 1974

By Jaril B. Lavrencic

The unique and irregulator distribution of working places in a mine always poses the two questions: - which and how much production equipment is to be used, - what production can be expected. Since the development of analytical methods would be impractical for such cases, a lot of computer programs has emerged in recent years trying to simulate the productiom process and thus find the best answer. The usege of a simulator has its dark side well felt by the author(s) of such a program: the credibility and the confidence of the customer. Using the simulator means to respect and to incorporate all the restrictions imposed by the narow underground space, methods of production, safety regulations etc., which can turn out to become a major programming effort. If the program is not properly structured, it will be used for a single special' case only, and never again. In this paper the structure and internal mechanism of the simulator is described for which the author believes that can easily be adapted to conditions of various underground and open pit mines. MINSIM tries to reach the following rather ambitious goals: 1) Estimation of the production before opening the mine, or a part of the mine. 2) Training the personnel to make decisions. 3) Making the daily time schedules for the entire fleet of the equipment units.

Jan 1, 1989

By William J. Campbell

Three types of X-ray analytical instrumentation were compared for applications in the secondary brass and bronze industry. The instruments were a conventional X-ray spectrograph, a portable X-ray spectrograph, and a radioiso-topic X-ray analyzer using balanced filters. The following two general applications were considered: Rapid identification for sorting scrap metals and quantitative analyses to provide guidance in the melting and casting of alloys. Twenty-three analyzed copper-base alloys were used as standards. Although the alloys varied widely in composition, matrix correction procedures were not necessary except for copper. The conventional X-ray spectrograph provides positive identification of the alloys and quantitative values for the six elements investigated--aluminum, copper, iron, lead, tin, and zinc. Equivalent results were obtained with the portable X-ray spectrograph for those elements whose characteristic X-rays are in the wavelength range of the instrument. The radioisotopic X-ray analyzer distinguishes certain groups of alloys and provides quantitative determinations for copper, lead, tin, and zinc. The sensitivity of the analyzer was marginal for the determination of small concentrations of elements of atomic number 26 or lower.

Jan 1, 1972

By Ryan A, Dennis R, Dekker D, Ellis W, Sowerby B

An automated facility for non-destructive elemental analysis of mine samples has been developed and tested at Mount Isa in association with the CSIRO. The analysis is based on the prompt and delayed measurement of gamma radiation emitted by the sample during and after separate fast and thermal neutron irradiation. No sub-sampling or sample preparation is required and the analyser is operated by one person that would otherwise be splitting drill core in preparation for conventional analysis. The analyser has been calibrated to measure the following (precision in parenthesis): Ag (14 ppm), Pb (0.5 wt%), Zn (0.5 wt%), Cu (0.04 wt%), Fe (0.7 wt%), S (1.1 wt%), SiO2 (0.8 wt%), A1203 (0.07 wt%), Mn (0.05 wt%), specific gravity (0.02 g cmt). Crushed or whole drill core samples that range in size between 0.5 m and 1.8 m of equivalent BQ size drill core can be analysed at a rate of six samples per hour. If required, drill core samples can be re-packed in their original configuration for storage following analysis. Standard samples are measured every day to ensure operational stability. The analyser is controlled by a personal computer which prints the results and stores them along with the raw data on the computer hard disk. This paper reports the performance of the analyser during 1992 for routine analysis of drill core from the lead ore bodies of both Mount Isa and Hilton mines.

Jan 1, 1993

By Thomas M. Barczak

This U.S. Bureau of Mines study evaluates factors that influence longwall support and strata interaction. The longwall system is composed of an immediate and main roof structure and three supporting foundations: longwall panel, powered roof supports, and gob waste. The main roof forms a structure that is generally supported by all three foundations, while the immediate roof acts as a beam that cantilevers from the coal face to the powered support. In most cases, shield loading involves a complex interaction of both main roof and immediate roof behavior and is a combination of loads produced from convergence of the main roof and displacements of the immediate roof caused by deformations of the cantilevered roof beam. Since the shield stiffness remains constant for all leg pressures and main roof convergence is irresistible in terms of shield capacity, the shield must be able to control the behavior of the immediate roof or floor structure for shield loading to be sensitive to setting pressures. If the goal is to minimize total shield loading, any active setting force must be offset by reduced passive shield loading to justify the active setting loads. Field data sumest that the typical reductions in passive loading do not justify the required increases in setting pressure in some applications.

Jan 1, 2010

By G. Goodall, M. Muinonen, R. Pandher, R. Jabbar, S. J. Muinonen

"The implementation of a new and highly efficient converting practice at the Glencore Sudbury Integrated Nickel Operations Smelter has opened the possibility to further capacity increases by using larger ladles. To quantify the impact of increasing ladle sizes from 200 to 300 ft3, XPS constructed a detailed discrete event simulation using the commercial software package Rockwell Arena®. The challenges associated with implementing a model on an intricate and tightly scheduled process, and the solutions needed to derive meaningful results will be presented. The aisle capacity is predicted to increase by approximately 17 %, with a reduction in furnace tapping demand of 8 %. Arena modeling capabilities and the key factors contributing to the overall capacity increase at the Sudbury INO Smelter will be reviewed and presented.INTRODUCTION The Glencore Sudbury Integrated Nickel Operations (INO) comprises two Ni-Cu-PGM mines, Strathcona Mill, and the Sudbury Smelter. The Smelter has operated continuously since 1929 using different processes to produce nickel-copper Bessemer matte. Feeds to the Sudbury INO Smelter are a blend of concentrate from Strathcona Mill, Raglan concentrate produced at the mine-mill complex in Raglan, Quebec, as well as third party concentrate feeds shipped to Sudbury from around the world. In 2016, the Sudbury INO Smelter produced 75,900 tonnes of nickel and 20,000 tonnes of copper in Bessemer matte. The product matte is shipped to Glencore’s Nikkelverk refinery in Kristiansand, Norway where it is refined to produce nickel and copper cathode. A schematic of the Sudbury INO Smelter’s flowsheet is shown in Figure 1."

Jan 1, 2017

By Rossiter W. Raymond

THE lead-mining industry of Missouri, as of other parts of the Mississippi basin, appears to have been paralyzed by the shock of competition with the mines of the States and Territories further west. It is difficult for establishments working galena ores, too poor in silver to pay for extracting it, to compete with the producers of the argentiferous carbonates of Utah and Colorado, who look upon their lead as a byproduct of little value, and are satisfied if it pays the charges of transportation, or the loss in smelting for silver. But simultaneously with this depression in the lead-mining of the Mississippi States, the development of new zinc deposits has caused a notable revival in the mining of zinc ores. There has recently been a sudden and strong rise in the price of spelter, which, though probably to a large extent temporary in character, has given important encouragement to prospectors and miners. Apart from the general recovery of business in the United States from the prostration of the past six years, the cause of the advance in spelter has been the falling off in production, resulting from the shutting down of several leading Western works,-the Martindale and Carondelet works, at St. Louis, and the Consolidated Company in Kansas. At the same time, the principal works at La Salle, Ill., were undergoing repairs, and produced less than usual, while the sheet-mill of Matthieson & Hegeler, at that place, was running as usual; so that this concern, ordinarily a large producer, entered the already depleted market as a buyer. These causes are in their nature transitory, and it is quite likely that spelter will be superabundant in a few months. Having lately received from a well-informed Missouri corres¬pondent some samples of the zinc ores and a general account of the ore deposits of Southwest Missouri, I have thought that it might interest the Institute to examine these specimens, and to hear such brief statements concerning the region as I am able, upon good authority, though without the aid of any personal investigation on the spot, to give. The zinc-bearing territory in Southwest Missouri appears to be very extensive; that is to say, zinc ores have been mined during the last year at various points throughout a district extending from the eastern edge of Kansas, west of Joplin, to a line some 50 miles east

Jan 1, 1880

By Daniel Alves Sodré

O processo de eletroerosão por penetração permite a usinagem de componentes metálicos nas mais variadas condições de tratamento termo mecânico e durezas. Entretanto, as tabelas e fórmulas tecnológicas empregadas para a execução deste processo não consideram essas distintas condições do material com uma variável. Desta forma, este trabalho objetivou avaliar a influência dimensional na usinagem via eletroerosão por penetração em componentes com e sem tratamento térmico de têmpera seguida de revenimento. Foram avaliadas amostras de aços ferramenta largamente empregados na indústria, representados pelas normas ABNT NM 122 Graus D6 e O1 e ABNT NM 87 Grau 1045. Observou-se uma variação dimensional de 20?m entre as amostras.

Aug 17, 2017

By M. Rehor

The importance of brown coal as a raw material is currently given by growing energy needs of Czech Republic. More than 70% of mined brown coal comes from North Bohemian Basin these days. Mining of brown coal is run in four mining locations. They are geologically different and the parameters of mining coal are quite different too. This requires a little bit different methodology of both extraction and reclamation. Methods of reclamation works in the region are given mainly by the characteristics of overburden rocks appearing in the upper horizon of recuperated localities. The difficulties of the North Bohemian mine dumps reclamation works are caused by extremely unfavourable properties of rocks poured down to the majority of mine dumps. These are mainly rocks of the overlaying strata and the rocks strata of brown coal bed. Main materials poured down to the mine dumps are sands, clayey sands and kaolin ? illitic clays. Admixtures in filled rocks consist of organic (coal) mass, siderite and pyrite. These rocks are mechanically instable with respect to the wind and water erosion and during weathering they are getting unfavourable, acid (phytotoxic) nature, due to the influence of SO3 and Al ions. External and internal dumps of open pit mines are significant part of the North ? Bohemian landscape sustained by excavation. Their as fast as possible preparation and gradual integration into ecosystem of the area is interest of both citizens of region and mining companies. The paper briefly summarizes the methodology of restoration of the largest dumps of the North Bohemian Brown Coal Basin and the results of analyses and evaluation of samples taken on restored localities Rado-vesice dump, Strimice dump, Ru?odol dum pand internal dump of Bilina mine. An example of modern non-tradicional restoration methods is the restoration of internal dump of Bilina mine (application of power plant stabilizer). According to observations and results of sample analyses the methods of restoration were selected to limit the erosion influence, adjust the chemical and physical composition of surface of Radovesice and Strimice dumps. The application of marlites and bentonite prevent the unfavourable weathering processes on dump surface. Compensation of Quaternary sediments was artifically formed here. The need of marlite ploughing in, application of organical substrates and vegetation preparation was proved on Radovesice dump. The conception of landscape reclamation of the largest dumps after finishing of mining, methodology of technical reclamation and well considered using of fertilizable soils are main results presented in this article.

Jan 1, 2014

The Wheeler Condenser & Engineering Co., of Carteret, N. J., is now building a line of horizontal and vertical shaft centrifugal pumps for general services, as well as for condenser work.. This company has been building centrifugal pumps for over 20 years, most of them being used, however, in connection with condensers. The new line of pumps is suited for all services. A small motor-driven unit for tank or stand pipe operation is shown in Fig. 1. Referring to the sectional illustration (Fig. 2), it will be seen that this pump conforms to the most recent advances in centrifugal pump construction, having a two-part divided casing, with the suction and discharge nozzles in the lower half. The impeller is of the closed double-suction type, protected by labyrinth wearing rings. The shaft is protected from the water by bronze sleeves, which screw on to the shaft and extend clear through into the bearing bracket boxes. Bearings are of the ring-oiled type, and in the outboard bracket, is a ring-oiled thrust bearing, which is a refinement not usually found in double-suction

Jan 4, 1916

By PDF

Previous work has shown that significant, free milling gold values exist in the Ryan Lode ore. This project used pilot scale equipment to estimate the percentage of gold recoverable by gravity methods from the circulating load of a conventional, closed-circuit, grinding mill. The pilot scale flowsheet employed three stages of gravity concentration, hydraulic classification and batch grinding to simulate a full scale milling circuit. 172 kg (379 lbs) of Ryan Lode ore were processed, having a head grade of 4.8 g/metric ton (0.14 oz/ton). Results showed that simple gravity methods are capable of recovering 45-50% of the gold values in a concentrate grading in excess of 3430 g/metric ton (100 oz/ton). Of the remaining gold values reporting to the classifier overflow solids (80% passing 70 microns, 3.1 g/metric ton (0.09 oz/ton)) 89% were recovered from 48 hour bottle roll tests.

Jan 1, 1995