Search Documents

Measurements of the rates of penetration at various throttle air pressures are presented as a function of thrust for three different rockdrills when drilling quartzites with strengths of 45 000 lb/in2 and 39 000 lb/in2, The rate of penetration at optimum thrust is shown to agree well with the predictions of theory and curves of air consumption as a function of throttle air pressure are presented. Man-held machines are shown to be under-thrusted at throttle air pressures above 40 lb/in2g. Measurements of bit wear as a function of distance drilled are presented graphically and discussed in terms of the theory developed in Part 1.

By C. A. Mitke

(Butte Meeting, August, 1913.) 1. Character of Gases which Caused Helmets to Get Out of Order. DURING September, -1911, the fire area in the Lowell mine continually increased and gases resulting from the fire came through the upcast shaft. These gases contained such a large percentage of sulphur dioxide that the men were unable to go up and down on cages, and, within a comparatively short time, repairs in the shaft were found to be necessary. Since the fire was in sulphide ores and extended into certain timbered sections, the gases contained varying amounts of SO2 CO2, and perhaps, at times, CO. The temperature in the shaft was generally about 97°, and the relative humidity from 97 to 99.5 per cent. The corrosive action of the fumes became apparent when the cables had to be changed more often than usual, the heads of lag screws .in the guides of the shaft disappeared, and the cages needed frequent repairs. It also became necessary to repair two compartments of the shaft by putting in 150 ft. of new guides between the 600 and 800 levels and lag screws in nearly all the old guides from the surface to the 800 level. 2. Ordinary Methods of Testing Helmets which were Unsatisfactory. These conditions required all work to be done by men wearing oxygen helmets. The Draeger type was tried, and was used until all repairs were completed. At first the helmets were. tested for air circulation and air tightness and the injector was tested by water gauge according to the methods recommended by the Draeger Oxygen Apparatus Co. Six arrangements, covering .these different tests, are illustrated in the catalogue and circulars of the company.

Jan 7, 1913

By Jan Svoboda, Toyohisa Fujita

The current status and history of innovation in magnetic methods of material treatment are reviewed. The milestones and key drivers of innovation in magnetic separation are identified, advantages of this technology in comparison to other physical methods of material manipulation are discussed and reasons for its failure to live up to its potential and expectations are indicated. Derailers that were responsible for the implementation failures are identified. The future focus in such diverse areas as mineral processing, waste treatment, recycling and biosciences is discussed and the research and development needs are outlined.

Jan 1, 2003

By P. K. Mululi, T. M. Yegulalp

The number and type of trucks and shovels used are two important factors in determining the optimal design parameters of an open-pit mining system. The characteristics of the arrival and service-time distributions of the trucks determine the performance measures of a truck-shovel system when it is modeled as a closed queuing network. In all of the previous analytical queuing studies of truck-shovel systems, trucks are assumed to be identical with respect to their arrival and service-time distributions. This assumption, although desirable for reducing computational difficulties, causes either underestimation or overestimation of the performance measures, depending on the number and types of equipment used in the model. The relative error in performance measures could be significant when the number of different types of trucks and shovels is large. In this paper, an analytical method is proposed to model the truck-shovel system as a multiple-class closed queuing network. This approach provides the capability of estimating system performance measures for planning purposes when the truck fleet is not necessarily composed of identical trucks. An example of truck-shovel systems is presented to show how the incorporation of different types of trucks affects performance measures.

Jan 1, 1998

By L. J. Buter, D. J. Collins

Introduction FMC's Paradise Peak gold mine was discovered by staff geologists in July 1983. Located south of Gabbs, in western Nevada, the deposit contains about 11 Mt (12 million st) of ore grading at 3.6 g/t (0.105 oz per st) of gold and 129 g/t (3.75 oz per st) silver. It is estimated that the ore contains 34 t (1.1 million oz) of recoverable gold and 933 t (30 million oz) of recoverable silver. The 3.6 kt/d (4000 stpd) mill began operation April 14, 1986, just 18 months after Davy McKee completed a feasibility study and construction, and two-and-a-months ahead of schedule. It also came in about 10% under budget at a cost of about $100 million. Crushing Run-of-mine ore is delivered from the mine in 45-t (50-st) haul trucks to a 272-kt (300,000-st) capacity open air stockpile. Ore is reclaimed using 5 m3 (7 cu yd) front-end loaders that feed a 91-t (100-st) hopper equipped with a 610- x 610-mm (24- x 24-in.) grizzly. A 1.4- x 11-m (54-in. x 35-ft) apron feeder delivers ore from the hopper by way of a vibrating grizzly screen with 127 mm (5 in.) openings to a 1- x 1.3-m (43- x 51-in.) Rexnord jaw crusher. Crushed material is conveyed to a 1.8- x 4-m (6- x 14-ft) Link Belt vibrating screen equipped with a 50-mm (2-in.) manganese grizzly bar deck. Screen oversize is fed to a 1.7/0.6-m (5.5 ft) Rexnord standard cone crusher. Product from this crusher joins the -50 mm (-2 in.) screen undersize and is conveyed to a 136-t (150-st) surge bin. Three hydraulically driven belt feeders deliver ore from the ore bin to three 2 x 6 m (7 x 20 ft) Link Belt single-deck tertiary screens fitted with 6 x 25 mm (0.25 x 1 in.) slotted polyethylene screens. Screen undersize - -6 mm (-0.25 in.) rock - is conveyed to a 3.6-kt (4000-st) ore storage bin. Screen oversize is delivered by way of a conveyor to a 91-t (100-st) surge bin. From this bin, two belt feeders feed ore to two 1.7 m (66 in.) Rexnord Gyradisc crushers, which are in closed circuit with the tertiary screens. Design features include magnetic protection for tramp iron removal and sloping floors and pump sumps for ease of clean up. Dust scrubbers keep the working environment clean and in compliance with state dust emission regulations. Grinding Two 1 x 4.5 m (3.5 x 15 ft) belt feeders deliver ore from the fine ore bin to a conveyor belt that feeds it to the 5 x 7 m (16 x 22 ft) Allis-Chalmers ball mill. The conveyor belt is equipped with a Merrick weightometer. This controls feed rate to the ball mill by speed control on the hydraulic motors driving the feeders. The 2.6 MW (3500 hp) powered mill grinds 3.6 kt/a (4000 stpd) to an average grind of 85% -75 µm (-200 mesh). The mill is in closed circuit with four 660 mm (26 in.) Krebs cyclones. Three of these are normally in operation while one is a standby. Warman pumps feed the cyclones through a cyclone distribution manifold. The cyclone underflow returns to the ball mill, which has a 300% average circulating load. Mill discharge pH is 11, and that is obtained through pebble lime addition to the feed belt. Cyclone overflow is sampled using a Heath & Sherwood two-stage sampler. It then flows to a 27-m-diam (90-ft-diam) Eimco thickener. Thickener overflow is returned to the grinding circuit, while underflow at 50% solids is pumped to the leaching circuit. Grinding-circuit design features include a steeply sloped floor for ease of clean up, an open area over the pumps for maintenance accessibility, and a ball hopper with a self discharge bottom to speed ball addition. Other features include a mill liner handler and an air clutch that connects the mill motor to the mill.

Jan 12, 1986

By Donald C. Barton

Geophysical methods of prospecting taken as a whole do not seem to offer much promise to a young man planning to enter them in the future. They have come to stay, to be sure, and they will continue in at least moderate use for a long time. Domestic use of those methods presumably is at a maximum at the present time. Geophysical prospecting is expensive; the effects of the law of diminishing returns in efficiency in finding prospects can already be recognized. Small oil companies, independent oil operators, and royalty buyers have been doing much geophysical work. But in face of the increasing costs of discovery of prospects and in face of the probably decreasing favorability of the prospects discovered, I expect to see a sharp drop in their use of geophysics within the next 10 years. The major oil companies and the larger small oil companies will continue to use geophysics indefinitely, but it seems doubtful whether the very extensive domestic campaigns of a few companies will be maintained for many years, certainly not for 10 years. The use of the geophysical methods in foreign countries has not yet reached its peak, and probaby will continue to increase for several years. That peak level of activity will probably be held for 10 years, although the site of maximum activity will shift from country to country; by the end of 25 years from now, I should expect the foreign use of the methods to have leveled off to one-fourth to one-half the peak level. Foreign service in geophysics does not seem to offer an attractive career, except for men of exceptional disposition. Young men just out of college, who are willing and who can afford to spend three or four years having a fling at adventure before settling down, will find it attractive, but when their tour of foreign service is over, they probably will have harder work finding a job than when they were seniors, and their foreign experience will count for little, except for further foreign service. A few men, mainly the higher men, will have headquarters at civilized or semi-civilized cities and towns or at permanent oil-company towns, and can

Jan 1, 1940

By Donald Barton

Geophysical methods of prospecting taken as a whole do not seem to offer much promise to a young man planning to enter them in the future. They have come to stay, to be sure, and they will continue in at least moderate use for a long time. Domestic use of those methods presumably is at a maximum at the present time. Geophysical pros-pecting is expensive; the effects of the law of diminishing returns in efficiency in finding prospects can already, be recognized. Small oil companies, independent oil operators, and royalty buyers have been doing much geophysical work. But in face of the increasing costs of discovery of prospects and in face of the probably decreasing favorability of the prospects discovered, I expect to see a sharp drop in their use of geo-physics within the next 10 years. The major oil companies and the larger small oil companies will continue to use geophysics indefinitely, but it seems doubtful whether the very extensive domestic campaigns of a few companies will be maintained for many years, certainly not for 10 years. The use of the geophysical methods in foreign countries has not yet reached its peak, and probaby will continue to increase for several years. That peak level of activity will probably be held for 10 years, although the site of maximum activity will shift from country to country; by the end of 25 years from now, I should expect the foreign use of the methods to have leveled off to one-fourth to one-half the peak level. Foreign service in geophysics does not seem to offer an attractive career, except for men of exceptional disposition. Young men just out of college, who are willing and who can afford to spend three or four years having a fling at adventure before settling down, will find it attractive, but when their tour of foreign service is over, they probably will have harder work finding a job than when they were seniors, and their foreign experience will count for little, except for further foreign service. A few men, mainly the higher men, will have headquarters at civilized or semi-civilized cities and towns or at permanent oil-company towns, and can

Jan 1, 1938

By Donald C. Barton

Geophysical methods of prospecting taken as a whole do not seem to offer much promise to a young man planning to enter them in the future. They have come to stay, to be sure, and they will continue in at least moderate use for a long time. Domestic use of those methods presumably is at a maximum at the present time. Geophysical prospecting is expensive; the effects of the law of diminishing returns in efficiency in finding prospects can already be recognized. Small oil companies, independent oil operators, and royalty buyers have been doing much geophysical work. But in face of the increasing costs of discovery of prospects and in face of the probably decreasing favorability of the prospects discovered, I expect to see a sharp drop in their use of geophysics within the next 10 years. The major oil companies and the larger small oil companies will continue to use geophysics indefinitely, but it seems doubtful whether the very extensive domestic campaigns of a few companies will be maintained for many years, certainly not for 10 years. The use of the geophysical methods in foreign countries has not yet reached its peak, and probaby will continue to increase for several years. That peak level of activity will probably be held for 10 years, although the site of maximum activity will shift from country to country; by the end of 25 years from now, I should expect the foreign use of the methods to have leveled off to one-fourth to one-half the peak level. Foreign service in geophysics does not seem to offer an attractive career, except for men of exceptional disposition. Young men just out of college, who are willing and who can afford to spend three or four years having a fling at adventure before settling down, will find it attractive, but when their tour of foreign service is over, they probably will have harder work finding a job than when they were seniors, and their foreign experience will count for little, except for further foreign service. A few men, mainly the higher men, will have headquarters at civilized or semi-civilized cities and towns or at permanent oil-company towns, and can

Jan 1, 1940

By F. S. Kendorski

This report covers the work on developing criteria for determining when a hazard exists when mining stratified mineral deposits beneath bodies of surface water. The nature of water bodies is considered, the disturbance to the strata induced by mining is described, inundation case histories reviewed, reasonable water inflows derived, and methods of mining to prevent or minimize the hazard are presented. Criteria are given whereby effected industries and agencies can recognize a potential hazard and plan a mine accordingly, releasing considerable mineral reserves otherwise considered unminable.

Jan 1, 1979

By Ana Paula Gonçalves Chaves

A pesquisa relativa ao transporte ferroviário no Brasil tem se intensificado nos últimos anos visando principalmente a melhoria no desempenho do par roda-trilho. Isso se deve a demanda de se transportar cada vez mais carga por eixo visando uma redução no custo de transporte. Através de mudanças na microestrutura do material ou de mudanças na composição das ligas utilizadas na fabricação pode se aumentar a resistência do par roda-trilho. Neste trabalho foi analisada a influência de diferentes microestruturas (puramente perlíticas e perlíticas-bainíticas), obtidas através de tratamento térmico por dilatometria, nas propriedades de um aço alto carbono similar ao utilizado em rodas convencionais classe C destinadas a implementação pesada com altas cargas e baixas velocidades. Foram realizados tratamentos isotérmicos em dez temperaturas diferentes para um aço eutetóide. As análises incluíram técnicas metalográficas (definição de fases presentes e distância interlamelar da perlita), ensaios mecânicos de dureza e ensaios magnéticos (saturação magnética e ruído de Barkhausen).

Aug 17, 2017

Ranger Uranium Mines Pty. Ltd. operates an open pit mine and ore treatment plant in the Northern Territory designed to produce 3 000 tonne/yr of U308 in yellowcake from 3 500 tonne/day of mill feed. The construction of this project was completed in 1981, 12 years after the discovery of the orebody. Wright-Davy, a Joint Venture of Wright Engineers and Davy McKee Pacific, were the Project Managers and Designers of the $270 million ore treatment plant and associated infrastructure. The project was designed in Sydney in -an office integrated with the Client, staffed by 35 key personnel drawn from Wright Engineers and Davy McKee, supplemented by personnel hired for the project. The peak Wright-Davy workforce in Sydney of 200 contained 113 design staff. The design principle of using the best practicable proven technology resulted in a plant which easily produces its design output using ore types outside the design criteria. The structuring of the project systems and industrial relations policies contributed to construction being completed within time and under budget. The plant was built without any major industrial dispute occurring and no dispute arose due to the uranium issue.

Jan 1, 1983

By F. E. Wood

This paper is written primarily as a discussion of Dr. W. P. Hase-man's paper on "A Theory of Well Spacing"' and presents briefly the production records, and intensity and rate of development in a large portion of the two principal producing sands in the Salt Creek field, Wyoming. The study includes 1350 wells, 160,000,000 bbl. production, well spacings varying from two to seven wells per 40 acres and early and late development. The general conclusions to be derived from this study are: 1. It is impossible to formulate a mathematical rule to apply to well spacing in the Salt Creek field. 2. Each tract is a separate problem. 3. Tracts first drilled produce the most oil, with many exceptions. 4. Initial production is not a reliable index to the relationship between past, current, or future production. 5. Wells which have produced the most oil in the past are not necessarily yielding the greatest current production nor will they yield the greatest future production. In fact, wells which have yielded the greatest past production will, in at least one-half the cases, make less oil currently or in the future than wells which have produced a smaller quantity of oil in the past. 6. The following is a safe rule to apply in well spacing in the Salt Creek field: (a) If the drilling of an additional well on a tract results in a sustained increased production, with prospects of making a profit, the tract is not overdeveloped and additional wells might be drilled. (b) If the drilling of an additional well does not effect a sustained increase in the production of a tract, the tract is fully developed. Second Wall Creek Sand The Second Wall Creek sand, covering 20,000 producing acres, is the principal producing horizon in the Salt Creek field; 1610 wells are producing at this time from this sand. This paper deals with hut a portion of the entire field including 10,680 of the more productive acres,

Jan 1, 1930

By C. F. Austin

lined-cavity shaped charge is an explosive mass with a cavity at one end and the detonator at the opposite end. The cavity is lined with a dense material, such as metal, glass, or a ceramic. Such an explosive device can be a useful drilling tool. Lined-cavity shaped charges are constructed to do just one thing — create a high-velocity jet of liner particles that can bore a hole in a target. The liner must be smooth and symmetrical, and high-velocity, high-brisance explosive must be used rather than ordinary commercial dynamites. Since the depth of target penetration is related to jet length, a standoff distance should be provided to hold the charge a short distance from the target. This allows the jet to lengthen prior to target impact. The best results are obtained when the jet is perpendicular to the target surface. Charges can be positioned for firing by taping them to a stake or simply laying them on a flat surface at the proper distance and angle with respect to the target. EFFECTS ON THE TARGET When a jet strikes a rock target, the jet and target particles at the jet-target interface move outward radially with respect to the jet axis to create a tremendous compressive load on the target material immediately below the target surface. The result is a shallow crater formed by spalling at the point of target entry. After cratering ceases, the steadily deepening hole continues to form as a result of the jet's imparting radial motion to the target particles at the jet-target interface. These radially moving particles collide with one another and with the hole walls, the net motion of the spent jet particles and target particles being back out of the hole in an axial direction (the backblast). The backblast keeps the penetration free of debris during penetration, al- though loose surface rock often falls into the hole after penetration ceases. The sudden stress relief after penetration ceases sometimes results in minor hole-wall rebound, which can partially fill the hole. The hole bottom will taper as the jet velocity decreases, until the jet velocity is too low to maintain the backblast. At this point the remaining jet and the following slug material are simply packed into the hole bottom. HAZARDS INHERENT IN USE Air blast from the highly brisant explosives used in shaped charges can damage nearby structures

Jan 1, 1961

By Ray W. Carpenter, Ralph Hultgren, Raymond L. Orr

Heats of formation of Au-Zn alloys of compositions Au3Zn and AuZn were rneasured at several temperatures by liquid tin solution calorimetry. The data for Au3Zn show that much smaller heat and entropy effects are associated with the a2- a1 transformation than for the a1 - a transformation. This result is consistent with reported X-ray diffraction studies which indicate that the a1 and (a2 phases have ordered structures which only slightly differ, whereas the a phase is disordered. The heat of formation of AuZn(ß') does not change significantly between 322o and 8000 K, confirming that the ß' alloy remains highly ordered to high temperatures. Not many measurements have been made of the energies of order-disorder transformations in alloy phases. In many cases these energies may be conveniently determined by measuring heats of formation as a function of temperature. Many alloy phases approximately obey Kopp's law of additivity of heat capacities; as a consequence their heats of formation do not change with temperature. In ordered alloys, however, a decrease in degree of order with increasing temperature will contribute an endothermic component to the heat of formation. Thus, for ordered phases where other anomalous contributions to heat capacity in the alloy or its pure components are absent, a measured change in the heat of formation may be attributed to the energy of disordering. A portion of the Au-Zn phase diagram1" is shown in Fig. 1. The composition AuZn(ß') has a well-ordered superlattice structure of the CsCl type at room temperature. The alloy is considered to remain ordered to its melting point,1 although, from X-ray diffraction data and electromotive force measurements of zinc activities, Terpilowski3 concluded that considerable disordering began at -673°K. The Au3Zn composition is a disordered fee solid solution (a) at high temperatures. Between 693o and 543oK, the ailoy orders to form the a1 phase, having a structure based on the L12(AuCu3) type, but with a regular distribution of ordering faults in the c direction, making it tetragonal. Below 543oK, the alloy orders further by means of slight atomic shifts, without diffusion, yielding a complex long-period orthorhom-bic superlattice structure, a2.4-7 Heats of formation of Au3Zn(a2) and AuZn(ß') were measured at 363°K by Biltz et al.8 by aqueous solution calorimetry. Heat capacities of several alloys between 14.9 and 38.4 at. pet Zn in the range from 373" to 723°K were measured by Iwasaki ef al.6 Stoichiometric Au3Zn, however, was not included in the alloys measured, the nearest composition being 26.1 at, pet Zn. Also, the heating rate used for the measurements, 2 deg per min, may not have permitted equilibrium to be reached in the neighborhood of the transformations. Heat contents of solid and liquid AuZn were measured between 488o and 1138°K by Kubaschewski.9 It was decided to determine the ordering energies of Au3Zn and to check on the possible disordering of AuZn by measuring the heats of formation of these alloys at several temperatures. The present paper reports measurements by liquid tin solution calorimetry of the heats of formation of the three phases of Au3Zn at temperatures within their regions of stability, and of AuZn at a low (322°K) and a high (800°K) temperature. EXPERIMENTAL Alloy Preparation and X-Ray Examination. Ten-gram ingots of Au3Zn and AuZn were prepared by melting weighed amounts of gold (99.95 pct Au) and zinc (99.99 pet Zn) together in sealed evacuated Vycor tubes at 1060°K, followed by rapid quenching. The resulting ingots were homogenized at 900°K for 10 days. The Au3Zn alloy lost no weight in preparation, the loss from the AuZn alloy was enough to introduce an uncertainty of only 0.1 at. pet in its composition. Filings for X-ray examination were taken from various parts of each ingot and strain-annealed at 723°K for 20 min in vacuo. The Au3Zn filings were quenched rapidly to retain the disordered phase. Diffraction patterns were determined with an X-ray dif-fractometer using copper Ka radiation.

Jan 1, 1968

By Walmir Pereira de Amorim Junior

Imersas em um mercado em constante mudança, as empresas têm seguido em uma busca contínua pela melhoria de seus processos. Diante disso, nos últimos 2 anos, o segmento de Aços Planos da ArcelorMittal Brasil vem passando por um processo de transformação, revisitando e reestruturando seus processos internos. Na área de planejamento um dos itens avaliados foi o processo de Planejamento de Vendas e Operações – Sales and Operations Planning (S&OP). O objetivo desse trabalho é a apresentação do novo modelo de S&OP da ArcelorMittal Brasil – Aços Planos, seus benefícios, e ferramentas utilizadas para suportar essa evolução: o SAP Integrated Business Planning for S&OP e a plataforma de colaboração SAP Jam, responsável por orquestrar todo fluxo de S&OP e as interações entre as diversas áreas envolvidas. O novo processo foi baseado nos conceitos existentes na literatura e também é objeto desse artigo. Além disso, no projeto de implementação do SAP IBP e SAP Jam foram utilizadas a Metodologia de Gerenciamento de Projetos baseada nas melhores práticas descritas pelo PMBOK (Project Management Body of Knowledge) do PMI (Project Management Institute) e a Metodologia SAP Activate para a implementação dos produtos. Como resultado da implantação desse projeto, foram obtidos vários benefícios, sendo alguns deles já atingidos e outros a serem capturados após o período de adaptação e estabilização dos processos e ferramentas.

Oct 30, 2017

By Masaru Imaizumi, Hiroyuki Nomura, Mitsuharu Takita

"Cast iron possesses many superior characteristics caused from precipitated graphite structure, for example, castability, wear resistance, solid lubrication, damping capacity. But the more graphite hyper-eutectic cast iron contains, the lower its mechanical strength becomes, because graphite gives a negative effect to strength of cast iron. In addition, primary graphite tends to segregate during solidification, so uniform materials are difficult to be produced.In this study, authors introduced semi-solid processing in developing new and high quality cast iron. A series of semi-solid processing experiments were carried out to clarify the effect of stirring condition; solidification temperature and etc. on microstructures and characteristics of cast iron. In particular much attention is paid to the appearance of ternary eutectic zone at the final stage of solidification. As the results advanced hyper-eutectic cast iron was obtained with high quality of both the mechanical strength and wear resistance. As for the mechanical strength, 300MPa and 0.60% are obtained as the tensile strength and the elongation values, respectively, under the controlled stirring condition. This indicates that semi-solid processed hyper-eutectic cast iron is used prospectively without spheroidization.IntroductionCast iron has various good properties such as wear resistance, solid lubrication, damping capacity and machinability. The characteristics of cast iron are mainly decided by graphite structure, namely graphite shape and its distribution in the matrix. Mechanical strength of cast iron is large in the case of small quantity of graphite particles which are precipitated uniformly, however, it becomes small in the case of large quantity of graphite precipitated flakily."

Jan 1, 2000

By D. T. Novick, M. B. Bever, B. Roessler

Ordered and disordered specimens of the alloy CusAu were cold worked and then annealed at 2880, 310°, and 340°C, together with disordered unworked specimens. me resistivity decreased during annealing mainly as a result of ordering; the resistivity measurements suggest that in cold-worked specimens the growth of antiphase domains is impeded. The strength properties increased during annealing at 288 "C; in cold-worked specimens this increase was lo a level above that for cold-worked specimens which had not been annealed. X-ray diffraction showed that after annealing for a few hours at 288ºC, the long-range order increased to a constant value; additional annealing at 288ºC resulted in the growth of antiphase domains in which the degree of order was constant. Changes in peak breadth and particle size confirmed that in cold-worked specimens the major effects of cold work were not eliminated during annealing at 288 "C, although a slight recovery process occurred. When a specimen of the alloy Cu3Au is heated to a temperature below the critical temperature (388ºC), long-range ordering tends to occur in a specimen containing less than the equilibrium amount of order characteristic of that temperature Ideally, a specimen of Cu3Au contains no long-range order if it has been quenched from above the critical temperature. Long-range order is reduced by cold work. If cold-worked specimens are heated, restoration processes such as recovery and recrystallization may occur,

Jan 1, 1963

The meeting was called to order in the Albany hotel, with the President, John B. Marks, in the chair. At the request of the Secretary, the chairman brought before the Institute the question of a reorganization of the finances and system of conducting the Institute, explaining that, although the Institute is in good financial shape and the meetings are of great interest and are attended by a large and serious minded membership, the Institute is getting so large and of such value to the operators that it should be taken over by the operators, conducted by some man elected by and from the operators, and its financing put on a definite basis. At present, it was explained, the Secretary, not a coal operator nor interested in operating, arranges and conducts all meetings and finances the Institute from three sources: the very low dues, the advertisements published in the Proceedings, and by direct solicitation of contributions among the supply and machinery houses. Mr. James Dalrymple spoke vigorously on the need of having the Institute entirely free from any taint of commercialism. Upon motion by W. D. Brennan, seconded, a committee of four, one to represent each State, was voted. Appointment of this Committee was deferred temporarily. The reading of the minutes of the previous meeting was then called for, but upon statement of the Secretary, that the minutes were published in Volume 2 of the 1925 Proceedings, they were dispensed with. The Secretary-Treasurer's report was made informally inasmuch as the last report had not yet been audited. In brief, the Secretary reported on a cost of approximately $1,600.00 a year to publish and send out the Proceedings, an expense of approximately $1,800.00 to care for the Denver meeting, and an expense of approximately $1,200.00 to care for the summer meeting. The Secretary's salary of $25.00 a month has not been collected, but a certain portion of this has been used for stenographic expense. The Secretary asked for expression from the floor regarding the advisability of continuing the publication on the present elaborate plan. Mr. Gibson, Mr. Marks, Mr. Whiteside, Mr. Littlejohn, Mr. Dick and others spoke positively on the value of the present form of the Proceedings, and urged that no changes be attempted in this. Upon motion of Holbrook Mahn, it was moved, seconded and carried that E. H. Weitzel and W. F. Murray be made life members of the Institute in recognition of their services in the organization of the Institute, placing them with Floyd W. Parsons as the original organizers of the Institute. Mr. Murray spoke briefly in acknowledgment of the courtesy. Mr. Weitzel's words are included in the discussion A letter was read from George B. Pryde relative to the present emblem of the Institute. Upon motion by Mr. C. W. Sinclair, seconded by Mr. Dalrymple, it was moved that the consideration of a new emblem be

Jan 1, 1926

By S. Carsten, S. Subramanian, R. Vasant Kumar, S. Vimalnath

"The effect of EPS components namely protein, polysaccharide and biosurfactant purified from Pseudomonas fluorescens was investigated for the bioremediation of Pb(II) ions in aqueous solution. Two parameters, namely the amount of EPS component and the concentration of Pb(II) ions were optimized for maximum Pb(II) ions uptake. The EPS components interacted with Pb(II) ions were characterized using energy dispersive X-ray analysis (EDAX) to ascertain the presence of Pb and by attenuated total reflection-Fourier transform infrared spectroscopy (ATR–FTIR) to reveal the functional groups involved in Pb(II) binding. The maximum Pb(II) binding capacities of protein, polysaccharide and biosurfactant were found to be 11.4, 0.55 and 0.11 mg mg-1 respectively. The biosorption processes followed the Langmuir model. The Gibbs free energy (?G0) values of -23.6, -20.9 and -23.2 kJ mol-1 for Pb(II) biosorption by protein, polysaccharide and biosurfactant respectively, attested to spontaneous, chemisorption processes. The ATR–FTIR results revealed the presence and involvement of amino, hydroxyl, carboxyl, phosphate, and methyl functional groups in Pb(II) binding and EDAX analysis confirmed the interaction of Pb with EPS components. The Pb(II) binding mechanisms of EPS have been discussed. The results demonstrate the potential of the purified EPS components of P. fluorescens for removal of Pb(II) ions from aqueous solution INTRODUCTION Waste water containing toxic metals from various industries pose a serious threat to human health and ecosystem. For treating such waste water, conventional methods like chemical precipitation, coagulation, evaporative recovery, electrodialysis, floatation, flocculation, ion exchange, reverse osmosis, nanofiltration, ultrafiltration are used (Lakherwal et al., 2014). These methods have some disadvantages like toxic sludge generation, incomplete metal removal and high cost (Singh and Gadi, 2012), necessitating the search for cheaper and efficient alternative methods. Bioremediation is one of the emerging alternatives where bacteria, fungi, yeast, algae and other biological substances are used as sorbents to remove toxic heavy metals (Vijayaraghavan, et al., 2015). Recently, the bioremediation potential of extracellular polymeric substances (EPS) of microbial origin has attracted attention. However, for Pb(II) removal, there is a paucity of literature focusing on EPS."

Jan 1, 2018

By B L. Coulter, E Wightman, A S. Burrows

With their commitment to sustainable development in an increasingly carbon-constrained world, many resources companies are focused on reducing the energy required to create their final products. In particular, the comminution and smelting of metal-bearing ores are both highly energy-intensive processes. If resource companies can optimise the energy efficiency across these two processing stages, they can directly reduce their overall energy consumption per unit mass of metal produced and thus reduce their greenhouse gas footprint. Traditional grinding and flotation models seek to improve the efficiency of mineral processing, but they do not consider the energy used by downstream metal production, eg smelting and refining. Concentrators and smelters individually may be running efficiently, but are they optimising energy consumption of the overall system? A key step towards answering this question is to understand whether it takes less energy to remove an impurity in the concentrator or the smelter. Analysis of the complete concentrator û smelter process chain may show that there are times when the concentrator should use more energy to reduce the overall energy requirements across the mill and smelter. The new methodology discussed here will integrate downstream processing energy with mineral processing energy, to find the overall most energy efficient circuit design and operating strategy. The proposed methodology includes: determining what grade and recovery positions can be achieved in the concentrator by using different combinations and amounts of grinding and regrinding, thermodynamic calculations of the energy used to process the different concentrate grades to metal, and integrating the concentrating and smelting models to find the lowest total energy for the system. A case study which investigates the effect of increasing regrinding energy on the overall mineral processing û smelting energy consumption is presented. For the copper-nickel sulfide ore investigated the addition of regrinding results in 11 per cent less energy being used in the overall concentrator û smelter process chain per tonne of metal produced. Although regrinding is often seen as an energy-intensive process, in this case study the use of 1 kWh of energy for regrinding reduces the overall energy consumption by 12 kWh. The new mill to melt methodology will allow companies to model energy consumption from mill to smelter with a view to reducing the energy-intensity and greenhouse gas footprint of their processing and smelting operations.

Jan 1, 2009