Search Documents

By Cadwallader Evans

THE American Institute of Mining Engineers was organized in the anthracite region of Pennsylvania by men who were primarily interested in anthracite. Its first meeting, at Wilkes-Barre, Pa., in the Northern Anthracite field, on May 16, 1871, resulted from a call sent out by three outstanding men of the anthracite .industry: Eckley B. Coxe, R. P. Rothwell, and Martin Coryell. The best known of these was Eckley B. Coxe, who was the manager of large hold¬ings operated by him and his family,. and who is remembered as the inventor of a special grate for burning very fine anthracite, known as the Coxe traveling grate, which is still very widely used. R. P. Rothwell was a well-known consulting engineer of the region, as was Martin Coryell, who was associated with another well-known anthracite family, the Pardees. There is no record of the discussions that resulted in this initial meeting, but it is safe to assume that the formation of the Institute was largely influenced, through appreciation by the founders, of the necessity for a free exchange of information covering the whole of the mining industry. One of the rules adopted at the first meeting was:

Jan 1, 1947

By M. G. Corson

UNTIL recently, the characteristics of cast copper have seldom been studied and such study as has been made has been inadequate. The prevailing idea seems to be that since pure copper is infrequently used in the cast state, there is no reason for trying to establish precise data regard-ing the properties of the metal in that condition. On the other hand, wrought copper either in the shape of sheets or wire rarely fails in service, except as a result of the action of reducing gases at the annealing tempera-tures, so there is little incentive to study the properties of the cast shapes -cakes, bars, ingots and billets-for-the sake of tracing the causes of failures of the wrought metal to the cast stock. However, about a decade ago, wirebars of American origin often cracked badly while being hot-rolled in mills in Germany. This led to four investigations: by E. Seidl and E. Schiebold,1 by P. Siebe,2 by O. Bauer and G. Sachs,3 and by G. Welter.4 These authors came to the conclusion that failures in hot-rolling were due essentially to the presence .of a wide zone of columnar crystals between the thin layer of fine crystals near the surfaces of the bars and the large but more nearly equiaxed grains of the central core. This macrostructural defect was explained in turn by the probable upward deviation in the temperature of the metal while it was being poured into the molds of the casting machine. More recently, cast shapes of copper were investigated by N. P. Allen5 and by C. Blazey.6 Allen examined vertically cast wirebars and hori-zontally cast wedge cakes of electrolytic tough-pitch copper, but only for the distribution of densities; i.e., porosity. Blazey was interested mainly in the mechanism of the variations in electrical conductivity clue to cold-work and anneal, but gave introductively an account of the composi-tion and average densities of the tough-pitch horizontally cast wirebars used. As far as the present writer can tell, no investigation was under-taken for the sake of presenting a picture of the distribution of mechanical characteristics in the wirebars of copper, tough-pitch or otherwise.

Jan 1, 1938

Mine design and selection of ore processing capacity depend upon a correct estimate of the grade-tonnage distribution. The estimate must reflect what can be recovered and processed. The McCoy/Cove operation in central Nevada, USA, is a gold and silver mine. Case studies of recoverable reserve estimation for gold and silver were made using multiple indicator kriging and the log-affine variance correction. From this model, the grade-tonnage distribution was constructed. Optimal pits were generated by utilizing the distribution, and the results were compared with the pit generated by ordinary kriging. Studies indicate that the proposed method for multi-metal recoverable reserve estimation is more accurate than ordinary kriging in terms of both tons and the grade. Using recoverable reserves for mine design will maximize global recovery of mineral resources.

Jan 1, 1997

"Geoscan is used for multi-elemental analysis of conveyed bulk materials in the minerals industry with proven performance and demonstrated paybacks of weeks or months in iron ore, manganese, copper, zinc-lead and phosphate industries. Geoscan-M measures continuously through the full bed depth and is unaffected by belt speed, particle size, layering, mineralogy and dust levels. Increments of typically two minutes are accurately measured and provide the plant operators with tonnage weighted results of contained elements. Measurement of the composition in real time enables prompt feedback to the mining operators and also feed forward to the process operators. Crushed ore increments can be diverted based on composition, such as diverting waste for disposal or marginal material to a stockpile for separate processing. Bulk sorting allows material to be placed into relevant stockpiles for subsequent blending to achieve consistency for process feed. Parameters used for decisions may be primary metal content, deleterious component content, other process parameter, or a combination of these. Process parameter may be the elemental ratio between critical components, e.g. Cu:S ratio, basicity, or the content of an “indicator” element (such as Si indicating material hardness). Benefits will be discussed based on case studies in copper and iron ore.IntroductionAs operators of process plants strive to remain competitive as capital and operating costs increase and commodity prices fluctuate, more focus has been directed at incremental performance improvements at incremental cost rather than major expansions to increase output. The philosophy of working smarter allows plants to adopt technologies proven in other industry sectors to minimise risk. This paper discusses one such technology that the minerals sector is adopting and has found to be safe, reliable and accurate with paybacks of weeks in most applications. New applications continue to be found and major benefits realised at various stages in the processing and handling of ores and products."

Jan 1, 2016

By Y. J. Wang

Along with the inexpensive availability of computing hardware, a proliferation of powerful personal computers is being realized throughout the mining industry. People from every arena within the industry are designing, developing, and/or applying mining specific software, which is increasing at a rapid rate. In this section applications (or potential applications) that are being made in the analysis and design of mine systems are discussed, including the design of compressed air networks, the simulation of hoisting operations, analysis of longwall face maintenance, and a summary of computer and software applications for analysis and design of coal operations. In "Computer Aided Design of Mine Compressed Air Networks" the authors describe software, called CompAir, and the underlying theoretical and mathematical foundations of it that can be used to make accurate, cost-effective designs of compressed air systems for mines. It includes algorithms for network analysis and the optimization of pipe diameters. The techniques embodied in the software replace traditional rule-of-thumb approximations which have been used in the past and avoid the operating problems that often result from using average, steady-state parameter values, estimated for ideal operating conditions. CompAir, coded in Turbo Pascal for personal computer use, bases calculations on compressible fluid theory, which gives more accurate results than incompressible fluid theory whenever high flow rates or long line distances are involved. The net- work and pipe diameter analysis is formulated as a nonlinear programming problem. The solution technique requires a trial and error approach that iteratively applies the unconstrained optimal pipe diameter algorithm to successive solutions of the constrained network problem until the diameters become "fixed." The authors conclude by recommending the use of a mine-wide monitoring system to improve cost control and provide a better understanding of flow regimes in compressed air networks.

Jan 1, 1989

By Kent Volkmer, Mark Sanders, Gregory Krohn, Tyler Blake, Daniel Wick, Barry Beith

This report describes a study designed to evaluate a proposed modification in the cap lamp battery cord intented to reduce the incidence of snagging and catching of the cord. A three phase evaluation as performed comparing a prototype with the standard, currently available cord. First, a "pull test" equipment was run. The second evaluation was a body conformity study. The third evaluation involved subjects performing common tasks in a low seam coal mine simulator. The results of these evaluations clearly demonstrated significant safety advantages of incorporating coiled cord into the design of the cap cord. The coil cord presented less of a snagging hazard, allowed the wearer more time to respond to a snag, and transmitted lower levels of force to the helmet when snagged. The research team recommended that cap lamp cords be commercially developed which incorporate coiled cord at the battery and helmet.

Jan 1, 1980

By Jianmin Qin, R. V. Ramani

The major parameters affecting dust flow at a longwall face are dust generation rate, air velocity and quantity distribution at the face, and the characteristics of the dust such as particle size distribution, density etc. Previous studies have identified the longwall shearer as the major source of the airborne dust in the faces. In this study, the effects of dust generation rate and shearer speed on the levels of ambient dust concentration are investigated. A series of experiments were performed under controlled conditions in a full scale simulated longwall face at the Lake Lynn Laboratory mine of U.S. Bureau of Mines using characterized bituminous coal dust. A trickle-duster was moved up and down the longwall face to simulate the shearer. In each experiment, a known amount of dust was dispersed by the trickle-duster into the air and the average dust generation rate was calculated. At the same time, gravimetric respirable and total airborne dust samples were collected and air velocity measurements were made along the face. The experimental conditions, data, and results are presented and discussed in this paper. The airborne dust concentration and air velocity data indicate that the concentration increases and air velocity decreases with distance from headgate for the first half of the face. Towards the tailgate, the air velocity increases with increasing distance but the dust concentration levels off with some variations. The data show that a higher dust generation rate results in higher dust concentration levels. More importantly, the data show that the rate of increase of airborne dust concentration is higher than that of dust generation rate. For the same air velocity distribution and dust generation rate, lower speed of the dust source results in higher airborne dust levels at the face.

Jan 1, 1991

By Dale K. Fields

With today's technological advances in mineral processing equipment, there is an increasing demand for accurate system control. This can only come about through representative sampling. The purpose of this paper is to guide you in the selection of sampling equipment and outline design parameters for the cutters used in dry and wet sampling without adding redundant mathematical probability formulas to your files. Special attention will also be given to the equipment used in conjunction with samplers and sampling systems, such as feeders, crushers, chutes, launders, and controls.

Jan 1, 1979

By Hongfa Hu, Stavros A. Argyropoulos

"This paper describes a mathematical model which simulates numerically reaction driven fluid flow phenomena. The driving force of this reaction is an exothermic heat of mixing. In addition, the model predicts the heat and mass transfer phenomena where both heat source and heat sink co-exist in close proximity. The heat source is generated by an exothermic reaction. The heat sink is formed by a moving boundary such as the melting of a solid. This type of phenomena occur quite often in various metal processing operations in which exothermic additions are immersed in liquid metals. The model is based on the SIMPLER algorithm and uses an enthalpy method to predict the fluid flow, temperature, and concentration fields. The results indicate that the exothermic mixing reaction was responsible for an abrupt rise in temperature around the moving boundary. The intensity of this reaction was also found to be responsible for the enhanced convection of fluid and the acceleration of the moving boundary. The modelling results were also verified by experimental work which included velocity and temperature measurements in a low temperature physical model. IntroductionAlloying additions are used extensively in the treatment of liquid metals during metallurgical processes. The alloying additions introduced into liquid metals can be classified into various classes, each of which follows its own route[l]. As a major group, the exothermic additions follow two different steps during their assimilation into liquid metals. In the first step, upon immersion, a metal shell solidifies around such additions, and then melts back. At this point, the second step commences. During this second step, due to the mixing of the addition with a liquid metal, an exothermic reaction occurs, which liberates large amounts of heat, resulting in an enhanced convection in the liquid metal surrounding the addition."

Jan 1, 1994

By Wu Tao, Lu Shijie, Xia Xiaoou, Zhang Ming

The impeller and stator are the most important components that can significantly influence the performance of flotation cells directly. The performance of the impeller and stator of KYF flotation cell is revealed by CFD (Computational Fluid Dynamic) simulation in this paper. A method of obtaining the circulation volume is proposed. The circulation volume is proportional to third power of impeller diameter. And the circulation volume increases linearly with the increasing of the speed. CFD simulation can draw the conclusions that there is a proportional relationship between power consumption, third power of speed and fifth power of impeller diameter. CFD prediction results agree with the theoretical formula. The difference between the forward and backward impeller is analysed in the paper. The circulation volume of the backward impeller is obviously larger than that of the forward impeller under the same condition, but power consumption of the backward impeller is lower. It is demonstrated that the impeller and stator system of KYF flotation cell is an efficient and reasonable stirring mechanism. CFD simulation could be reliably used in flotation cell design and optimization.

Jan 1, 2014

By R. J. Johnston

"INTRODUCTIONPoint Mines is located about 65 miles east of Hay River on the South Shore of the Great Slave Lake. It is connected to the Northern Alberta Railway System by the Great Slave Lake Division of CN Railways at Roma Junction, Alberta.The operation started in the fall of 1965 with a capacity of 5000 t.p.d. An addition was put into operation late in 1968 to bring the capacity up to 8000 t.p.d. The present milling rate is 11,000 t.p.d.The location of Pine Point Mines is such that long end cold winters are to be expected end temperatures of lower than -200F are encountered from late October to late March, with extended periods of -300F being common in January and February.It was recognized by Cominco engineers during the initial design period that since freezing would be encountered with open pit ore somewhere in the crushing circuit, the problem was to reduce it as much as possible. Other mines, working under similar conditions, found that the fine ore bins feeding the grinding circuit were the main problem area. The decision was reached, therefore, to have heated fine ore bins and to make sure thst the ore was sufficiently warm to prevent freezing.CRUSHING PLANT FLOWSHEETThe crushing plant has a standard open flow circuit (flowsheet). Ore from the stockpile is loaded into R-50 Euclid trucks by Caterpillar 992 Front End Loader with 11 cu. yd. bucket and dumped into a 42 x 65 C.A.C. Superior Crusher driven by a 300 HP motor. The crusher is set at a nominal 5 inches. The ore falls through into a 100-ton surge bin. There are high level and low level nuclear gauges to allow the primary operator to optimize for optimum orientation."

Jan 1, 1972

By C. A. Queener, W. L. Mitchell

In recent years bismuth telluride has received considerable attention, primarily due to its value as a thermoelectric material. Since there seems to be little dependence of thermoelectric effect upon crystal orientation1 many of those who have previously worked with this material have been unconcerned with knowing its crystallographic angles to any degree of accuracy. However, when one studies deformation modes, lattice stresses, or the aniso-tropy of mechanical properties of a material, knowledge of the interplanar angles and their relationships as depicted in a stereographic projection becomes essential. Lange2 originally published crystallographic data which described the structure of bismuth telluride as rhombohedral with the space group A more recent work by Francombe3 presented data which corroborated and refined the original findings of Lange. In addition, Francombe established that there is no coexistence of rhombohedral and hexagonal lattices in bismuth telluride as was suggested by Vasenin and Konovalov,4 and that the structure can be treated as a pseu do hexagonal structure with an axial ratio, c/a, of 6.95 for convenience of presentation and study. The interplanar angles and standard projections for several unalloyed hexagonal metals have been previously published,5-9 but the present work appears to be unique in that it presents data for a rhombohedral compound in pseudohexagonal form. As a pseudohexagonal structure, this material has an extremely large axial ratio as compared to the usual range of approximately 1.5 to 1.9 for the hexagonal metals. Since the interplanar angles are a function only of c/a, the angular relations between various planes for Bi,Te3 will be grossly different

Jan 1, 1965

By J. O. McCaldin, P. Duwez

ALLOTROPIC transformations between 1000° and 1900°C have recently been reported for several metallic elements. Since the proposed transformations are based on limited evidence, it was decided to examine the elements in question as well as some refractory metals by thermal analysis with a photoelectric technique similar to that described by Hug-gins, Roll, and Udin.1 In this method, a lead sulphide cell was used to detect thermal radiation from an electric-resistance heated strip specimen. A thermocouple spot welded to the specimen was used to calibrate the temperature of the system under steady temperature conditions, and recording was accomplished with a cathode ray oscilloscope. In the method used by the present authors, the temperature calibration was omitted and the cathode ray oscilloscope was replaced by a recording galvanometer. This technique, in which electric current passing through the specimen heats it, will be referred to henceforth as Method 1. Another arrangement was required for those cases where the specimen could not be formed into a wire or strip suitable for resistance heating. In such cases the specimen was a sintered compact heated by thermal radiation from a hot tungsten strip, Fig. 1. The specimen was insulated from the heating strip with a thin layer of thoria powder or suspended on 0.004 in. tungsten wires. The take-up spring had just sufficient tension to prevent buckling of the heating strip due to thermal expansion. This technique will be called Method 2. Both methods were tested with specimens of iron and titanium and the well known allotropic transformations, a toy and ? to 8 in iron and a to in titanium, were very clearly detected. Fig. 2 shows one of the records obtained for titanium. For this particular experiment, the iodide titanium specimen was a square rod 0.080 in. on an edge and 3 in. long.

Jan 1, 1955

By J. Preussner, U. Glatzel, R. Völkl, S. Prins, M. Wenderoth

Platinum base alloys are very corrosion resistant and have got a high melting point. Similar to Ni-base superalloys, which are used for jet turbines, the hardening effect of the intermetallic L12Pt3Al phase is used to receive a material that is creep resistant at high temperatures. Chromium is added to the alloy system to stabilize the L12phase down to room temperature. With the right amount of nickel the misfit and shape of the precipitates can be controlled. Various alloy compositions have been melted and analysed. With scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) a microstructure can be observed, which is very similar to the one in Ni-base superalloys. To support alloy development with simulations, a thermodynamic database of the Pt-Al-Cr-Ni system is about to be established. The SEM and EDS measurements provide useful input to the thermodynamic optimization. Also many data from the literature have been used to receive the best approximation. The Cr-Pt binary phase diagram has been reassessed and the latest results of thermodynamic modelling are presented.

Jan 1, 2006

By J. D. Steenkamp

In 2002 the commissioning of an ilmenite smelter on the North Coast of South Africa was extended by three months due to the failure and subsequent replacement of the magnesia-based refractory lining. The lining failed due to the hydration of magnesia caused by an unexpected source of water. The incident resulted in significant financial losses and a prolonged insurance claim which was settled in 2009. As magnesia-based refractories are used extensively in both ferrous and non-ferrous applications, the authors of the paper want to share the experience gained from this incident with others. The paper reviews the literature available on furnace start-up practices and explains the hydration of magnesia using available sources. The incident is studied in more detail, both technically and economically, and the costs incurred are quantified in terms of the cost of the original lining. The paper concludes with lessons learned and recommendations made for future work. The intention of the paper is to stimulate open debate regarding best practices in preheating of furnaces lined primarily with magnesia. Keywords Commissioning, hydration, start-up, magnesia.

Jan 1, 2011

By Stephen Semeniuk

Discussion by Stephen Semeniuk Discussion As a valuator and SME member, I view Ross D. Lawrence's position as based on unproven and faulty assumptions made with regard to the pragmatic evidence presented in his paper. Moreover, his call for the inclusion of all mineral resources in discounted cash flow valuations is redundant, if not irrelevant, as there are procedures that already take all classes of mineralization into consideration for valuation purposes. In my experience as a valuator, I find that Canadian securities regulators are more than accommodating in allowing any valuations of mineral properties to be based on cash flow calculations. In other business areas, the same regulators usually reject discounted cash flow valuations of projects or businesses with no operating history. Instead, the regulators prefer valuations to be based on other transactions tested in the marketplace. Valuations based on actual market transactions are less subjective than discounted cash flow calculations and/or the capitalization of arbitrary, untested or undemonstrated earnings projections. In the mining and minerals sector, such projections may be made by persons not qualified to make such projections. In support of this statement, I direct readers to the article "Valuation of mineral properties which do not contain exploitable reserves" by Lionel C. Kilburn, which appeared in the August 1990 issue of the CIM Bulletin. To quote from the article: "Value of a mineral property depends basically upon metal prices, recoverable grades, mining and metallurgical practices, commodity supply and demand, and political-economic conditions, all of which vary with time. Five fields of expertise influence the value of a mineral property: •geological engineering, •commodity markets, •financial markets, •stock markets and •mineral property markets. The skills of geologists and engineers properly apply to the first field of expertise. Knowledge and consideration of the other four fields is important, but such advice is more properly sought from marketing experts, economists and stockbrokers." Securities regulators have created no hardship for valuators by excluding unsubstantiated resources in discounted cash flow valuations. In the field of engineering, best design practices apply. A margin of safety is built into the design criteria for any new equipment or structure that will exceed normally expected load levels and stresses, even though such considerations imply higher front end costs. In accounting, the comparable operating principle is conservatism. It explains why, for balancesheet presentation purposes, inventory is stated at cost or market, whichever is the lowest value. Similarly, when the engineering or geoscience-based valuator plays in the field of finance, the rules of accounting and applied economics apply. Regulators in their skepticism of income-based valuations are in tune with similar views already expressed in mining literature. To quote H. Van Tingley, in Mining Magazine, July 1996: "... the DCF method has inherent dangers when applied to undeveloped resources. Firstly, it presents an often-undeserved aura of accuracy. A DCF value is no more accurate than the least accurate of the assumptions incorporated into the calculation - and assumptions

Jan 1, 2003

By M. Ito

The authors have developed the RETAC jig (a modified TACUB jig) and have reported that the RETAC jig can separate relatively low density particles such as plastics. To further improve the separation ability, a hybrid jig (a RETAC jig with an air bubbler under the particle bed), which can separate plastics having similar specific gravities by the differences in the wettabilities of the particles was developed. Surface modification of plastics with similar wettability enabling separation in the hybrid jig and the effects of wettability control of the plastics using reagents are reported.

Sep 1, 2012

By E. DeGolyer

PROSPECTING for new deposits is a part of the ordinary routine business of the petroleum industry to an extent that is not true for any other mineral industry. The health of the industry depends upon whether we are successful or unsuccessful. How many know what it costs to find oil today and what it has cost in the past? Very few, I will wager. The industry is not well informed upon this extremely important point. We cannot deal in averages for lack of information. Does it cost more or less than previously? Prospect wells are increasingly deeper and, since the introduction of the core drill, prospecting techniques have required increasingly expensive field oper-

Jan 1, 1939

By H. Thomas, I. N. M. Nday

"*Paper written on project work carried out in partial fulfilment of BSc.Eng (Mining Engineering) degreeThe optimization of the cycle time to increase productivity at Ruashi Mining was an on-site project investigation conducted from December 2017 to January 2018. The main objective of the investigation was to determine the actual cycle time components. These comprise the queuing time, loading time, hauling time, and dumping time of ADTs (articulated dump trucks). Data was also collected on two hydraulic shovels to identify where these could be optimized. The actual cycle time obtained was compared to the theoretical cycle time to ascertain the constraints, which affect productivity. By applying Systems Thinking to the cycle time, man-made constraints of the actual cycle time were identified and recommendations to mitigate them suggested to optimize the cycle time. However, rainfall is a natural constraint that adversely affects the actual cycle time, and which cannot be mitigated.In addition, both the theoretical and actual cycle time were analysed, as well as the theoretical and actual productivity for the year 2017. Based on the findings, conclusions and recommendations were made to optimize the cycle time. IntroductionThe aim of the project was to increase Ruashi Mining’s productivity by 39%, from about 7.537 Mt of broken material mined to 12..367 Mt targeted in 2017.BackgroundRuashi Mining is a copper (main commodity), cobalt (by-product), and acid producer located in the Democratic Republic of Congo (DRC), 10 km from the city of Lubumbashi. Figure 1 shows the location of the Ruashi Mining open pit.Ruashi Mining started production in 1911 and in 2005 the mine was registered as a DRC company owned by Metorex Group Limited. In November 2013, the Chinese company Jinchua Group International Resources Co. Ltd. bought a majority stake in the business. Ruashi Mining currently produces 38 000 t of copper and 4400 t of cobalt per annum. The company has contracted NB Mining (a contract mining company) to transport its ore. To optimize the productivity of the mine, considering ore flow delivery at Ruashi Mining, the cycle time is the indicator used in this project. The cycle time components were recorded on site using a stopwatch."

Jul 1, 2019

By Lar Liljeblad

"As demands upon the earth's natural resources continue to grow, exploration companies, mining organizations and others face the problem of the need to tackle increasingly more difficult strata to open up new reserves. Innovations in materials technology and tool design have steadily improved this capability, but none perhaps so drastically as a recently introduced cemented carbide in which tool wear resistance and/or toughness can be tailored precisely to the user's drilling needs.Introduction Until about forty years ago, the bulk of rock-drilling operations had to be carried out with hardened steels. Short life between re-grinds was common especially in abrasive rock formations. Shortly after World War II, Sandvik, Sweden, pioneered the development of sintered (cemented) carbide-tipped steel tools as a means of improving drill tool life. The new material was a composite of tungsten carbide and cobalt, the latter acting as a 'cement' to bind the wear-resistant carbide grains together, and the composite, in turn, was brazed to the steel. The immediate effect was a 100-fold increase in the service life of the tool.Intractable ProblemsWhile the carbide-tipped tools served the mining and quarrying industries admirably there were, nonetheless, some seemingly intractable limitations. The greater the wear resistance of the material - the quality for which it is selected - the more brittle it is. Also, rocks vary widely in hardness and abrasiveness and no single tool, either in terms of material or shape, meets every need. Specifically, for fast penetration of non-abrasive rock, toughness must be combined with a relatively sharp tool prome. Highly abrasive rock, on the other hand, demands a substantially broad area of extremely wear-resistant material on the tool if long bit life is to be assured. Between these extremes there are innumerable variations in rock"

Jan 1, 1991