Search Documents

By J. R. Batista

Leachates from gold heap-leaching mines contain selenium concentrations as high as 2 mg/L. Previous studies report satisfactory selenium adsorption by activated alumina when using relatively "clean" drinking waters. However, the findings of these studies cannot be directly applied to the treatment of mine leachate where other ions compete for the alumina adsorption sites. This study evaluated the adsorption of selenium from a mine leachate to develop design parameters for full-scale activated alumina processes. The study revealed that 68% of the selenium in the leachate could be removed by alumina at pH > 5.0. Silica adversely affected the selenium adsorption capacity. At pH values < 4, silica was poorly adsorbed by alumina and selenium adsorption was improved.

Jan 1, 1994

By W. W. Adams

Because of insufficient funds for printing, the Bureau of Mines was unable to publish its annual bulletin covering accidents at metal mines in the United States for the year 1933. A brief mimeographed summary of the principal statistical data for that year was released to the public late in 1934. Since then reports for 1934 have been received from the mining companies, and in order to avoid further delay in releasing this information to the mining industry and others interested in the prevention of accidents in mining, statistics for both years are presented in this publication with a minimum of interpretation and comment. The fatal-accident rate for the metal and nonmetallic mines (excluding coal mines) of the United States was more favorable in 1933 than in any previous year since 1911, the first year for which the Bureau of Mines obtained reports from the operators. Further progress was made in 1934, when the fatality rate was even lower than that of 1933. On the other hand, the nonfatal-accident rate, which had reached its lowest level in 1932, increased in 1933 and increased further in 1934, although not to such an extent as to prevent the rate for either of those 2 years from being better than that for any year previous to r1931.

Jan 1, 1936

By R. Thorpe, M. Dosbaba, A. Kopriva, A. Niiranen, J. Ruokanen

"Automated Mineralogy (AM) is an important diagnostic tool in flotation plants as it adds ore and particle mineralogical properties to traditional mass and chemical data. AM is used in project development, for future ore studies and for diagnosing concentrator operations. With the exception of operations who own central laboratory or on-site systems, the use of AM is often limited to the analysis of a comparatively small set of samples. Metrix Plant Technologies has partnered with TESCAN to integrate TIMA AM technology into the implementation of Performance Assessment Campaigns (PAC). Routine daily composite samples from the mill are analysed mineralogically on a size-by-size basis over several weeks. All the relevant metallurgical, process control and mineralogical data is combined into a single large database for mass balancing and interactive examination. This paper describes the implementation and results of a PAC at the Agnico Eagle Kittilä gold mine in Finland. Although challenging, the addition of mineralogical data as dependent variables in multivariate analysis leads to a much deeper understanding of the root cause effect of events driving the flotation performance. INTRODUCTION TO STUDY The Kittilä mine, owned by Agnico Eagle, is Europe’s largest primary gold mine, with annual production of approximately 180,000 Oz. The operation is located in Lapland in northern Finland, and is currently expected to operate until 2035. The location of the operation is shown in Figure 1. Historically, the mine was an open pit, although in recent years ore is sourced solely from underground operations. The processing plant features crushing and grinding, followed by carbon flotation and sulphide flotation. Carbon concentrate is a waste stream, and sulphide concentrate reports to pressure oxidation (autoclave) and CIL circuits for gold extraction. The final flowsheet is shown in Figure 2. Following commissioning in late 2008, the operation achieved commercial production on May 1st 2009. Gold recovery in flotation gradually increased to a 92-96% range at a throughput of ~3500-4000 tonnes per day. In late 2014, the operation commissioned a plant expansion to ~5000 tonnes per day. Following a commissioning period, the operation stabilised with recoveries in a 90-94% range, which over any given period was determined to be ~2% lower with statistical significance. The trends from start-up of gold recovery in flotation and throughput are shown as follows in Figure 3. In early 2016, Agnico Eagle Kittilä mine, along with Agnico Eagle Technical Services (AETS) partnered with Metrix Plant Technologies and TESCAN, to perform a Performance Assessment Campaign (PAC) at Kittilä, involving automated mineralogy on five key streams at Kittilä on 40 days selected from a 50 day period between February 15th and April 4th 2016, when plant operations were stable. In addition to the mineralogical data, metallurgical and operational data were pooled into a single, powerful database to explore opportunities for the operation to improve recovery in a sustained manner, ideally to the levels pre-expansion."

Jan 1, 2017

By A J. Kyle

After a brief description of the shaft and surface facilities, this paper describes the planning for the mining operation, the selection of equipment the general method of mining and the sequence of operation. All of the major items of equipment are described, including the components of the power system. The detailed planning is reviewed -from the shaft sinking to the three-shift mining operation. Excavation and equipment changes, as well as long-range planning, are al o di cussed. Introduction THE successful completion of the Yarbo No. 1 shaft of International Minerals & Chemical Corporation (Canada) Limited in July, 1962, added a new type of mine to Canada&apos;s many producing operations. IMC Esterhazy is a unique mining operation in Canada; in fact, it is unique to potash mining in general. Not only is thi&apos;3 a trackless operation utilizing shuttle cars and belt conveyors in its material handling systems, but it excavates all of the ore with continuous boring machine<:;.

Jan 1, 1964

By G. Chancellor

"INTRODUCTION The paste plant is located at the Barrick Goldstrike mine in Northern Nevada on the Carlin Trend. The Goldstrike property consists of an open pit and an underground mine; along with two processing facilities: a roaster and an autoclave. The underground portion of the mine produces approximately 1,800,000 ore tons per year and approximately 400,000 ounces. The mine is broken up into four distinct zones: Banshee, Meikle, Rodeo and Northpost. The current paste plant services both the Rodeo and Northpost zones. Development of the conceptual designs and permit approval for this plant was an extensive process that took over a decade to complete. A testing program was developed in conjunction with this process and implemented throughout to ensure the following metrics were achieved: ensure no environmental impact, material available onsite would be able to flow through the pipe to all required locations, and that this material could achieve the appropriate final strength. PLANT AND UNDERGROUND CONSTRUCTION This is the first paste plant to be built in Nevada. The paste plant at Goldstrike began construction in January 2012 and was completed in March of 2013. This plant was constructed to service the Rodeo side of the underground mine which previously utilized a cemented rock fill (CFR) plant to meet their backfill needs. However, in March of 2013, the same month the plant was commissioned, the raise that fed this CRF plant was mined out in a planned phase of the adjacent open pit. This made the switch to paste all the more difficult as it was being relied on for as the sole source of backfill production even though the system yet to be fully tested and optimized. The plant was designed to be fed with onsite Roaster tailing which would be thickened and then mixed with cement and fly ash. The plant was designed to pump 177 tons of paste per hour with a utilization of 65%. The original design specifications for the paste were 77% solids with varying binder contents depending on where the paste was being placed"

Jan 1, 2015

By G. L. Oldright

The Metallurgical Branch of the Bureau of Mines, as a part of its duties under the Organic Act, works to prevent wastes in industry and to disuse inmate information on the fundamentals of metallurgical processes. During the war, the necessity of large production was increasingly emphasized. Such duties necessitate from time to time the study of units of full commercial size, the operation of which is beyond the facilities of the Branch. When developments have reached this stage; work has been continued in cooperative agreements with operating companies that have been willing to contribute the use of their plants and staffs and to allow the publication of the results obtained for the common good of the industry.

Jan 1, 1948

By Stanley F. French, Bruno F. Koch

Although the amount of dust that will be actually recovered in the six main dust-control systems cannot be accurately stated until the tests mentioned previously are carried out, it is estimated that the average air entering the wet collectors will contain around 5 grains of dust particles per cubic foot. This means that the six systems handling a total of about 133,000 cu.ft. of air per minute will return about 68 1/2 tons of dust to the concentrator per day and since the copper in this dust will average around 2 per cent, the total recovery is approximately 1.37 tons of copper every 24 hours. This important copper recovery is not due entirely to the dust-control system since in a plant without control only the duct that is dispersed to the atmosphere represents a loss. A conservative estimate of the recovery of copper solely due to the dust control system would be about half of the total or approximately 0.70 tons of copper per day.

Jan 1, 1942

By W. H. Oppelt

A small, annular-retort gasifier having a nominal capacity of 40 pounds of lignite per hour was designed and constructed at the Lignite Experiment Station, Grand Forks, N. Dak. The purpose of the investigation was to increase the capacity of an annular-retort gasifier by better temperature distribution in the heating chamber (adjacent to the annulus) and by supplemental internal heating with controlled amounts of air. Correct control of air admission should yield crude ammonia-synthesis gas having a (H2+CO)-N2 ratio of 3. Dakota Star stoker-size lignite was used during the exploratory experimental program. The effects of temperature level and distribution in the heating chamber and of addition of air to the reactor were investigated. Hydrogen - carbon monoxide ratios ranged from 1.9 to 2.5, and (H2+C0)-N2 ratios were as low as 2.9. Hourly gas production ranged from 970 to 2,580 cu. ft., or 62.0 to 164 cu. ft. per sq. ft. of heated surface, or 350 to 940 cu. ft. per cu. ft. of reactor volume. Data from the small gasifier could be readily correlated with those previously obtained in the commercial-scale unit under comparable experimental conditions.

Jan 1, 1957

By John C. Niedzielski

The PHX Sky Train is a five mile long automated people mover system located at Phoenix Sky Harbor International Airport. Phase I of the PHX Sky Train includes the design and construction of 227 drilled shafts supporting three stations and approximately 9,000 feet of elevated guideway. The guideway includes a 100 foot high, 330 foot long span extending over an active taxiway, which will be the first system of this kind over an active taxiway in the world. The soil conditions in this area generally consist of alluvial Sand, Gravel and Cobbles (locally known as SGC) deposited by the nearby Salt River. The foundation system will support relatively high axial loads, lateral loads and moments due to the height of the guideway above the ground surface, where it needs to pass over existing concourse walkways, bridges, a taxiway and buildings. Drilled shaft design involves designing 4.5-foot to 9-foot diameter drilled shafts within the SGC deposits, most of which extend well below the groundwater table. There is a high potential for collapse of drilled shaft excavation sidewalls within this material. Such extreme design loading conditions, together with difficult ground conditions at the site, result in several challenges for the design and construction of the deep foundation system for the guideway and stations. A load test shaft was designed and constructed as a means to provide site-specific measurement of axial performance under these difficult conditions. Results from the load test were used to reduce the size of the drilled shafts. This paper provides an overall description of the PHX Sky Train project, a summary of the ground conditions, design requirements, load test results and construction methods and equipment used to successfully install the drilled shafts for this project.

Jan 1, 2010

By I Canbulat, J Oh, A Mcquillan, D Payne

This paper presents a new risk assessment tool for coal mine excavated slopes. This new empirical-statistical Slope Stability Assessment Methodology (SSAM) is intended for use by geotechnical engineers at both the design review and operational stages of a mine’s life to categorise the risk of an excavated coal mine slope. A likelihood of failure is determined using a new slope stability classification system for excavated coal mine slopes developed using a database of 119 intact and failed case studies sourced from open cut coal mines in Australia. Consequence of failure is based on slope height and stand-off distance at the toe of the excavated slope. Results are presented in a new risk matrix, with slope risk being divided into low, medium and high categories. The SSAM is put forward as a new risk assessment tool to assess the potential for, and consequence of, excavated coal mine slope failure. Unlike existing classification systems, assumptions about the likely failure mode or mechanism are not required. Instead, the SSAM applies an approach which compares the conditions present within the excavated slope face, with the known past performance of slopes with similar geotechnical and geometrical conditions, to estimate the slope’s propensity for failure. The SSAM is novel in that it considers the depositional history of strata in an excavated slope and how this sequence affects slope stability. It is further novel in that it does not require explicit measurements of intact rock, rock mass and/or defect strength to rapidly calculate a slope’s likelihood of failure and overall risk. Ratings can be determined entirely from visual observations of the excavated slope face. The new SSAM is designed to be used in conjunction with existing slope stability assessment tools. CITATION:Mcquillan, A, Canbulat, I, Payne, D and Oh, J, 2018. New risk assessment method for coal mine excavated slopes, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 473–495 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By P. A. Boeck

The thermal insulation of high-temperature equipment for industrial purposes is a subject that has not received from engineers and designers the attention its importance deserves. This may be attributed to a number of causes: In the first place, heat flow is a rather difficult factor to measure under the working conditions of an industrial furnace, and until the comparatively recent introduction into certain operations of the heat balance sheet, with a systematic attempt to account for the discrepancies in the totals, the various causes of heat losses and the reasons for their existence were not brought to light. Moreover, such rapid advancement and radical changes in the design of equipment, especially in metallurgical lines, have occurred that practice has apparently outdistanced the theory of design. In the modern tendency toward greatly increased size of units, effort has seemingly been made to utilize the heat of fuel gases without proper attention having been paid to conserving heat energy and confining it strictly to the points of maximum activity. The systematic study of the thermal properties of structural materials, which is being carried out by various government bureaus and also by a number of technical societies, is forming the basis for more intelligent and consistent work in the economically important subject of prevention of fuel waste. Advantages of Insulation It is not necessary in this practical and utilitarian age to enlarge upon the need of prevention of heat losses, but attention may advantageously be called to the other benefits derived simultaneously with the saving in fuel and the increase in thermal capacity of furnaces when properly insulated. In most industrial furnaces—which are here spoken of in the broadest sense, indicating general high-temperature equipment for any purpose and heated in any manner—the operations are generally carried on through a temperature range which has been found by practice to give the most ef-

Jan 1, 1916

By Ray Brainard, Adriana Ventimiglia, Amanda Kerr

The $2 billion Horizon Lateral includes over 30 miles of trenched and tunneled pipeline with diameters up to 120 inches.Related infrastructure includes large and small pumping stations, reservoirs, and flow control facilities. This paper will discuss the strategy and processes used to determine contract packaging and contracting delivery methods for the various project elements with an emphasis on the tunnels and trenchless crossings. Prior Authority experience and the rigorous risk-based approach to develop the preferred alignments played a large role in determining the outcomes along with schedule concerns and permitting and easement acquisition.

Jun 13, 2023

By J. Sikamo, A. Mwanza, C. Mweemba

"The Zambian copper mining industry as we know it today had its genesis in the 1920s. Consistent private sector-driven investment in the industry over a period of over 50 years in exploration, mine development and operation, development of minerals processing facilities, building of infrastructure for pyrometallurgical and hydrometallurgical processing, with attendant support facilities, including building of whole new towns, resulted in copper production rising to a peak of 769 000 t in 1969, providingover 62 000 direct jobs. The industry was nationalized in 1973 and remained in government hands for just over 24 years. During this period, the industry experienced a serious decline in production levels, reaching the lowest level in the year 2000 when production was 250 000 t. An average of just under 2000 jobs were lost every year in the 24-year period, reaching just over 22 000 direct jobs in 2000.Following the return of Zambian politics to pluralism and liberalized economic policies, the government decided to privatize the mining industry. The process started in 1996 and by the year 2000 all the mining assets had been privatized. The new investors embarked on serious investment to upgrade the assets and to develop greenfield mining projects. Fourteen years later and after more than US$12 billion investment, production levels increased year-on-year to a peak of 763 000 t in 2013 with direct jobs reaching 90 000.This paper discusses the impact of the mining industry in Zambia on the economy in areas such as employment, support for other industries, direct contribution to the national gross domestic product (GDP), foreign exchange earnings, and social amenities. The paper also focuses on the performance of the mines during these periods vis-à-vis mineral availability, mineral grades and complexity, new technologies, and human capital. This is looked at particularly in the light of current challenges the industry is facing. Suggestions are proposed on how the industry can be nurtured to continue being a major driver for the Zambian economy and a major player in the international copper mining business."

Jan 1, 2016

By Fair A, Oxenford J

Syncrude Canada Ltd operates one of the largest open pit mines in the world at Fort McMurray in northern Alberta, Canada. In 1993, Syncrude mined and processed 131.2 Mt of oil sands to produce 67.0 MBbls of synthetic crude oil (SCO). This represents approximately 13 per cent of Canada&apos;s crude oil requirements. In addition to the oil sand mined, Syncrude moved approximately 96 Mt of overburden ahead of the mining operation in 1993. Since start-up in 1978, Syncrude has had outstanding success in improving the safety and reliability of its operation. Much of this success has been achieved by reducing risk through the application of new and improved technology. This improved safety and reliability has resulted in, among other things, very significant improvements in operating costs and profitability. This paper discusses some of the technology applications that have been introduced at Syncrude to reduce risks to people, equipment, operations and the environment. Three specific examples will be discussed in detail to demonstrate how reductions in risk have greatly improved the operation.

Jan 1, 1994

By Dao-Wu Yang, Ju-Lan Zeng, Li-Xian Sun, Yan Yao

"The hydration heat of the pure cement, the fly ash single-dopped cement, as well as the fly ash and fluorgypsum co-dopped cement were investigated by means of micro-calorimety with an eight-channel micro-calorimeter (TAM Air). The results showed that the hydration heat and the hydration rate could be reduced significantly by fly ash and fluorgypsum. However, the reduction was not proportional to the loading of dopant. The exothermic peak of the fly ash and fluorgypsum co-doped cement was appeared earlier than the fly ash single-doped cement. As the temperature decreased, the hydration heat and the hydration rate of the doped cement were reduced, and the exothermic peak appeared later. The effects of fly ash and fluorgypsum on the compressive strength of cement were also investigated. The results revealed that the early compressive strength of concrete made up of the co-doped cement was largely higher than that of the fly ash single-doped cement. Based on the experiment results obtained in this paper, we could conclude that fluorgypsum is a suitable additive for fly ash-doped cement.IntroductionFly ash and fluorgypsum are industrial waste. In 2008, nearly 400 million tons of fly ash has been produced by coal-burning power plants in China. And it is estimated that this number would exceed 500 million at the year of 2015. Besides, every year the fluoride salt factories in China discharge more than 100 million tons of fluorgypsum. Tremendous of fly ash and fluorgypsum occupy considerable land and contaminate air and water sources [1]. As a result, comprehensive utilization of this two industrial waste has draw great attention from all over the world.Cement is the most-used construction material on earth. But the production of cement consumes huge energy and destroys the environment. This problem might can be partly solved by applying fly ash and fluorgypsum as additive for cement [2-4]. During the last decade, some papers that focused on applying fly ash and fluorgypsum as additive for cement have been published [5, 6]. However, to the best of our knowledge, none of these papers investigated the hydration heat of the fly ash and fluorgypsum co-doped cement.The hydration of cement is an exothermic reaction, which can result in serious problem for mass concrete: The interior of the concrete could reach very high temperature as the hydration proceeded [7-9]. As a result, the great temperature difference between the interior and the outer of the concrete would exist and cause serious thermal stresses. Thus, the concrete would be destroyed by the cracks which in tum are resulted from the thermal stresses [10, 11]. The heat released by the cement hydration and the hydration rate is commonly regulated by adding mixed materials or transferring additive such as fly ash and fluorgypsum [12-14]."

Jan 1, 2011

By E. L. Singleton

This Bureau of Mines investigation was initiated to study and establish some of the chemical and physical characteristics of the condensed Mno-Si02 system. To prevent oxidation of the manganous ion, I atmosphere of purified helium was used in the furnaces. Solidus-liquidus curves and invariant points were established from melting-point determinations and were supplemented from data obtained by the static-quenching method. Experimental findings and data are for the intermediate compounds of tephroite and rhodonite with their respective eutectics represented at 25.5 and 37.2 weight-percent silica. Tephroite melts congruently at 1,347° C., and rhodonite melts incongruently at 1,286° 8.. A metastable transformation was determined to exist at the 1,347° C. isotherm, the congruent melting point of tephroite. A composite X-ray-diffraction pattern was formulated for synthetic rhodonite. This investigation contributes fundamental data leading toward a better understanding of the more complex slag systems.

Jan 1, 1962

By S. Hume, J. Shepherd

Meso-2,3-dimercaptosuccinic acid(DMSA) was studied as an additive for thiosulfate leaching of gold. DMSA was added to solutionscomposed of either sodium thiosulfate or calcium thiosulfate and the solutions were tested for their ability to leach pure gold samples as well as a calcined gold ore from Barrick Gold Corp. Results showed prolonged leaching of pure gold samples when DMSA was added at a concentration of 5µM; however, higher concentrations were shown to inhibit leaching. Differential capacitance measurements of the interface indicated that DMSA adsorbed as a defective monolayer on the surface of gold at low concentrations and formed a more compact monolayer with increased concentration. It is proposed that a concentration of 5µM DMSA produces a defectivemonolayer on the surface that still allowsthe transport of oxidants to the underling metal while inhibiting the formation of polysulfide passive layers that arise fromdecomposed thiosulfate.The 5µM DMSA/CaS2O3 system was also studied using calcined ore. Results showed that the initial leaching rates in the presence of DMSA are lower than those obtained in thiosulfate alone. However, after 10h, prolonged leaching is again observed when DMSA is included.

Jan 1, 2015

By G. W. Poling

This paper evaluates current environmental protection legislation, guidelines and criteria, focusing mainly on the land and water disposal of mill tailings. Effluent criteria and regulatory mechanisms are proposed, and submarine tailing disposal is discussed at length. The importance of basing regulations on the best available rationale is stressed.

Jan 1, 1979

By R. N. Chakravorty

Early detection of spontaneous combustion is of utmost importance in underground coal mining to prevent major disruptions of production and to ensure a safer working environment. This paper presents the work done in developing a suitable system for the early detection of heating in a hydraulic coal mine. Laboratory studies on the products of oxidation for Balmer 10 seam coal showed that a significant amount of carbon monoxide is produced during the early stages of heating and that detection methods based on the analysis of other gases, such as hydrogen, ethane or ethylene, are not a better alternative for this coal. The four-point carbon monoxide monitoring system recently installed at the hydraulic mine is discussed in this paper. It is believed that by studying the trend of carbon monoxide concentration in the mine air, it will be possible to detect heating at an early stage. Field tests carried out so far have indicated that infra-red technology will prove to be a powerful tool in the hydraulic mine, particularly for locating hidden oxidation or fire in cracks, fissures, underground workings and coal outcrop areas before it spreads extensively. The project is jointly sponsored by EMR, CANMET, Mining Research Laboratories and Kaiser Resources Ltd.

Jan 1, 1978

Automated drilling in surface mines is here, it?s successful, and it?s already at work in mines around the globe. Coal, copper, iron and gold mines in large mining countries such as Canada, Australia, South Africa, the United States and Chile are meeting mining objectives previously ruled out as unattainable. Pit Viper automation enables operators to accomplish more objectives safely. Operator assist functions like AutoLevel, AutoDrill, Auto Rod Changer and multi-rig teleremote control are a few of the features mines are using to gain consistent, sustainable productivity.