Search Documents

By F. D. Everett

This report, based on information made available by four uranium-producing companies, describes the geology, exploration, open-pit development and mining, and shaft sinking in the Gas Hills uranium district of Wyoming. Open-pit stripping features motor-scrapers push-loaded by crawler or rubber-tired tractors. The ground generally can be ripped, and little blasting is necessary. Detailed data are given on grouting for ground stabilization in sinking a small-diameter shaft in the relatively unconsolidated sandstone and siltstone, Cost and performance data are presented as made available by the companies.

Jan 1, 1963

By R. R. Angel

Drilling rate is a parameter that should be considered in determining the volume requirements for air and gas drilling. The use of past methods which ignore the effects of the solids content upon the pressure and velocity of the annulus flow stream can result in undercalculation of the required volurne by as much as 50 per cent. A vertical-flow equation is presented for determining volume requirements. This equation includes the effect of the solids that are transported up the annulus in the flow stream by incorporating the drilling rate as one of the parameters. The effect of down-hole temperature on required circulation rates is also ana-lvzed. A simple approximate method of determining volume requirements is presented. This method is more accurate than the methods used in the past. Hole cleaning difficulties are analyzed for a recent air drilling job where past methods indicated that - excess air was being used. Sample curves of calculated boitom-hole pressures are presented for air and gas drilling in several hole sizes. INTRODUCTION In certain areas the use of air or natural gas as a circulating medium for drilling oil and gas wells is becoming a common practice. Large increases in penetration rate and bit life are achieved through the use of these media in preference to mud or water. Drilling rates as high as 90 ft/hr have been obtained in shales. The importance of maintaining adequate circulation rate is generally recognized; however, much disagreement exists among drilling operators as to what constitutes "adequate" circulation rate. In quarry drilling, where annular velocities can be accurately determined, an annular velocity of 3,000 ft/min of standard air is required for best results in rocks having approximately the same density as those commonly penetrated in drilling oil or gas wells'. Although this standard air velocity has proven satisfactory for quarry drilling, some oil and gas well drilling operators believe that an equivalent annular velocity of more than 4,000 ft/min is required; others believe that as little as 2,000 ft/min . is sufficient. Much of this disagreement results from determining the required circulation rates with methods which fail to incorporate the drilled solids in an equation which is applicable to vertical flow. Hughes Tool Co. Bulletins No. 23' and 23-A3 present data for determining circulation rates based on the Weymouth formula. These data do not include the drilling rate as a parameter and, therefore, neglect the effect of the solids being transported up the annulus. In spite of this apparent defect and the fact that the Weymouth formula is not applicable to vertical flow, the Hughes data have well served the drilling industry in many areas and are important and timely contributions to the science of air and gas drilling. The Hughes data purposely omit a correction for increasing down-hole temperature. At slow drilling rates this effectively compensates for the use of a formula which is not valid for vertical flow; however, volumes determined by the Hughes method are not sufficient to support rapid drilling rates at moderate and great depths. For example, Phillips Petroleum Co.'s Cauthorn "D" No. l in the Vinegarone field for Val Verde County, Tex., was air drilled from 1,500 to 9,300 ft using a compressor delivering 1,400 cu ft/min. The 8 3/4-in hole was drilled with 5-in. drill pipe, and drilling rates as high as 90 ft/hr were obtained between 7,000 and 9,300 ft. No water or caving hole was encountered. At 7,728 ft it was necessary to wash-out 60 ft of cuttings to reach bottom after a trip to change bits. At 8,130 ft a twist-off occurred and the drill col-lars were stuck in drill cuttings. These difficulties indicate that the 1,400 cu ft/min of air was not sufficient to keep the hole clean. Hughes data indicates that 1,180 cu ft/min is sufficient to produce an annular ve-

Jan 1, 1958

By Kiyoshi Shibata

A new assessment model has been proposed for metal production and its recycling system. The model consists of three processes, smelting of ore, cascading and upgrading of metal scrap. The present approach is to assess the total energy consumption of the system, by introducing two equations for describing the relationships between critical impurity content and the mass of production or scrap recycling. The total energy consumption in the system can be described as a function of recycling rate and performance of the upgrading process. The present model suggests that the impurity removal efficiency and yield in the upgrading process are essential to reduce the energy consumption in the systems. Especially, such points should be explicitly controlled in recycling of aluminum. The potential capability of this model was also discussed by obtaining several quantitative information required for the process design and the operational control of beneficial recycling of metals.

Jan 1, 1998

By J. A. Organiscak

Longwall mining technological improvements have provided significant increases in productivity over the last 15 years. Longwall productivity is anticipated to continue to escalate with expanded application of automated equipment. Automation technology that will likely be adopted over the next 5 years is memory cut with shearer initiation of shield movement supervised by a couple of face workers. Operations using this technology will most likely relocate many production workers from the face to the outby gate entries and position several face workers outby the shearer, exposing workers to different health and safety risks. These changing risks are primarily related to worker relocation and expected increased production levels. Workers outby the face will most likely have less dust and noise exposure, but will be exposed to other safety hazards associated with outby equipment movement, materials handling, and gate entry ground movements. The face workers will most likely be exposed to higher respirable dust and noise levels generated by the equipment at elevated production rates. Methane gas emission is also expected to increase with faster mining rates. These operational changes and the control technologies needed to reduce redefined longwall worker hazards at semiautonomous longwall operations require examination to maintain the health and safety of mine workers.

Jan 1, 1996

"Since World War II, urban communities have expanded at an unprecedented rate. The industrial mineral industry supplies the sand, grave], limestone, crushed rock, cement, gyp-sum, etc. for urbanization. Most de-posits in use are close to or within communities. Pollution of water and air has become a matter of public concern. Waste disposal and the effects of noise and vibration are subjects of public debate. Need for the reclamation of land after operations such as strip mining is discussed in magazine articles and on TV pro-grams; i.e., the general public is educated in the unattractive features of mining.Legislation is on the books and being drafted to regulate mining operations and their side effects. To avoid over-regulation and restrictive legislation, it is necessary that the public be educated and legislators informed of problems peculiar to the mining industry. Our side of the story needs publicity."

Jan 1, 1968

By C. Guney Olgun, Charles Elks, Sherif L. Abdelaziz, James R. Martin, Christopher Fox, Pier Luigi Iovino, Fatih Catalbas, Pierre Gouvin

"Energy piles are a new innovative renewable energy technology to access and exploit the relative constant temperature of the ground for efficient heating and cooling of buildings. Examples of energy piles include drilled shafts, continuous flight auger (CFA) piles, driven piles, and micropiles. A field test setup was installed at the Virginia Tech Geotechnical Research Facility to study energy piles. The field test consists of a total of five micropiles 25 cm (10 inches) in diameter, four of which were equipped with circulation loops. The test piles extend to a depth of 30.5 meters (100 feet) and are heavily instrumented with strain gauges and temperature sensors. Several observation boreholes were formed around the test piles to monitor ground temperatures. Thermal conductivity tests and field load testing were performed to investigate the behavior of Energy Piles. This paper presents results of the thermal conductivity tests and thermo-mechanical field load test performed as part of this field investigation.IntroductionThere is a developing trend around the world to explore alternative energy sources. The main driving forces are growing global energy demand, depleting natural resources and the adverse effects of greenhouse gas emissions from fossil fuel consumption. Geothermal energy is one of the promising renewable sources that can be utilized to offset such trends. However the use of geothermal energy has been limited mainly to certain hot spot areas where it is used either for district heating and/or electricity generation. Ground temperatures below a depth of about 6 meters (20 feet) remain stable compared to outside air temperatures, typically lying between 8-23°C (46-73°F) at most U.S. regions. The constant temperature and heat storage capacity of near surface soils in any region represent a tremendous potential of stored energy that can be used for heating and cooling of structures."

Jan 1, 2017

By C Czerny, T Elkington, L Lorenzen

The Dutwa Nickel Project is a nickel laterite atmospheric leach project located in Tanzania that has been under development by African Eagle Resources plc (2012). A bankable feasibility study (BFS) has been progressed to evaluate mining of the resource (107 Mt at 0.92 per cent Ni) followed by hydrometallurgical processing on-site to make a mixed nickel-cobalt intermediate product. The unique relatively high silica contents in the Dutwa deposits, as opposed to limonite, which is more commonly occurring in nickel laterites, presented the possibility for beneficiation of the ores to enhance the leach feed nickel grades and provide economic benefits in terms of operating and capital cost efficiencies.Geometallurgical relationships, based on the results of an extensive variability metallurgical test work program for beneficiation and leaching, were developed for the BFS, which resulted in an improved understanding of ore classifications within the deposit and their responses. The geometallurgical information obtained has been instrumental in making key preliminary techno-economic decisions, such as forecasting whether or not mined material should be beneficiated and was ultimately used to drive the mine plan towards the prioritisation of areas within the deposits that delivered the best cost efficiencies and overall project economic outcomes.CITATION:Elkington, T, Lorenzen, L and Czerny, C, 2013. The use of geometallurgical relationships in process route selection and mine plan optimisation for the Dutwa Nickel Project, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 207-216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By J. Roger Loebenstein

This report presents a U.S. Bureau of Mines study of the flow of arsenic-containing materials in the United States, based on the best data available in 1991, includes a consideration of arsenic as a byproduct of the processing of nonferrous metals, the fate of arsenic in manufacturing wastes, the quantity of arsenic used in products, tile fate of arsenic in dissipative uses, and the useful life of discarded products. Where possible, estimates are given of the amounts of arsenic lost from the materials flow. Arsenic byproduct of mining nonferrous metals. Historically, most U.S. production has been from the states of Montana, Washington, and Utah. The smelters in these states are believed to be the areas of the country where arsenic is most concentrated in the soil, tailings ponds, and waste dumps. Since the closure of the last domestic producer of arsenic in 1985, all arsenic has been derived from imported sources. Historically, arsenic was important in agricultural applications as an insecticide, herbicide, and cotton desiccant. As the environmental movement gained momentum and the toxicity of arsenic became better understood, most of the agricultural uses for arsenic were banned. Beginning about 1975, the use of arsenic as a wood preservative began to grow. After 1980, wood preservative uses became more important than agricultural applications. By 1990, 70% of the arsenic consumed in the United States was used by the wood preservative industry and 20% by the agricultural industry. The major source of domestic arsenic emissions in 1989 was from the U.S. copper processing indus¬try. About 7,800 mt/yr of arsenic was discarded in leach dumps, tailings, and slag. Another 800 mt/yr was liberated to the atmosphere and 1/100 mt/yr was exported in copper concentrates. On the consumption side, 9,200 mt/yr was lost, mostly from dissipative agricultural uses and the disposal of obsolete arsenical products.

Jan 1, 1994

By M Thompson, N Vines, Z Hearne, S Lam, G A. Gomes-Sebastiaõ, D van der Spuy

Construction and commissioning of the Nova Copper-Nickel project of Independence Group was completed in late 2016. The plant is in the Fraser Range of Western Australia, about 120km east of Norseman and produces separate Copper and Nickel concentrates. Since the early feasibility phases of the project, the importance of automation and control was recognised and planned for to ensure the plant performance meets the design expectations. The site is well equipped with common as well as advanced instrumentation. It currently boasts the largest number of Blue Cube MQi (mineral quantifier inline) slurry grade analysers on a single plant worldwide. It was also decided that 25 Blue Cube TempoTracks would be installed on the flotation cells. The TempoTracks provide information on froth height and velocity, hence giving continuous, quantitative measurements of the froth that is pulled off each cell, rather than relying on infrequent, subjective visual inspections.The Nova concentrator consists of a differential flotation circuit whereby copper bearing mineral are selectively floated prior to nickel flotation. It is imperative that losses of copper to the nickel circuit, and vice versa, are minimised. The plant metallurgical team and Process IQ collaborated to develop and implement the advanced control strategy for the plant. This paper focusses on the optimisation of the copper concentrate that is pulled off the copper rougher and scavengers. This strategy was made possible by the additional measurements listed above. The control optimisation of the copper rougher and copper rougher scavenger circuit was implemented during August 2017 on the StarCSTM advanced control platform. It continuously optimises the level and air setpoints. The control philosophy incorporates several notable techniques which include: a variable mass pull target that is a function of the quantity and grade of material entering the circuit, integrated compensation to prevent inventory build-up in cells, balancing of the froth velocity over the lip of each cell to adaptive, modular system usage and advanced error handling. CITATION:Gomes-Sebastiaõ, G A, Hearne, Z, Lam, S, van der Spuy, D, Thompson, M and Vines, N, 2018. Nova copper-nickel project optimisation of the copper rougher-scavenger circuit through advanced measurement and control, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 77–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By G. M. Carr-Harris

"THE SUBJECT of permanent molding has received a great deal of attention in the technical press as illustrated by the many excellent articles in the bibliography which follows. In general, this covers the period 1940-1958 and is merely representative of what is available. Numbers in •brackets refer to items in the bibliography.It may be desirable at the outset to give a few definitions covering those terms directly related to this subject. The following is a definition of permanent-mold casting as given by J. W. Meier in a paper, ""The Non-Ferrous Metals and Alloys"", read before the Ottawa Valley Chapt.er of the American Society for Metals:""Permanent Mold Casting is used where a large number of castings of the same part are required and higher mechanical properties, greater density and closer tolerances are essential. Since metallic mold s are very expensive, the number of castings must be sufficient to, defray, at least partially, the added expense. Molds are usually made from a good quality cast iron, 1but other mold materials, such as the aluminum and copper alloys, graphite, ceramics, etc., are being used in certain cases. Important factors in permanent mold casting are the mold temperature; the proper mold dressing; and, as in all other casting methods, the mold geometry, that is to say, the design of spruces, gates, risers and vents""."

Jan 1, 1960

By Frank D. Shepherd

THE Gunnar Gold Mines property is on the west shore of Beresford lake, in the Rice Lake mining division, southeastern Manitoba. Gold was first discovered in place in the Rice-Beresford Lakes area in 1911 on the Gabrielle claim, now included in the San Antonio Mines property at Rice lake. Following an eastward trend of favourable prospecting ground, promising showings were next staked in the vicinity of Long lake during the years 1915 and 1916. At that time, William Walton and associates, among them Gilbert LaBine, staked the Eldorado vein, north of Long lake, and Eldorado Gold Mines, Limited, was formed to develop the property a Company that, later, was to become widely known through successful operation of its radium-silver mine at Great Bear lake, Northwest Territories. Continuing eastward from Long lake, Walton and his partners, Gunnar Berg, Leo Seaberg, and Wm. Quesnel, staked claims during the years 1920-24 in the vicinity of Beresford lake which, later, were to become incorporated into the Gunnar Gold Mines property. The presence of gold-bearing quartz on these claims had been known from the time they were staked, but an opportunity to consolidate them into a group was not forth-coming until early in the year 1933. Although promising gold showings had been disclosed during the performance of assessment work on individual claims, no continuous mineralization having mine-making possibilities was discovered until after the consolidation of the entire group. From this stage onward, progress was rapid. Active exploration was begun on August 1st, 1933, and late in October James Houston reported favourably on the property. On October 27th, Gunnar Gold Mines, Limited, was incorporated in the Province of Ontario to develop and operate the property. The Company is also registered in Manitoba. The authorized capitalization is 3,000,000 shares of $1.00 par value. Gilbert LaBine was appointed president of the Company, with James Houston as mine manager. Following completion of a diamond-drilling programme, planned in 1933, it was decided to install a mine plant capable of carrying development to a depth of 1,000 feet. A transmission line, 5 miles in length, was built to the Great Falls-Central Manitoba line of the Manitoba Power Company, Limited.

Jan 1, 1939

By William M. Dalrymple, William P. Owen, Benjamin S. Rivers

For the California Department of Transportation (Caltrans), geophysical applications have played an important role as part of a successful multidisciplinary approach to subsurface characterization for the design of high value structures. Since at least the 1950’s, geophysical methods have been deployed to guide the exploration drilling program and to maximize the return on drilling investment by increasing the amount of data obtained from test borings. Geophysical applications saw increased use beginning in the 1990’s, during the seismic retrofit of the state’s toll bridges and the replacement of the west span of the San Francisco-Oakland Bay Bridge. Over the intervening years, increases in computing power and increasingly sophisticated commercial off-the-shelf software applications have allowed Caltrans to leverage advancements and perform geophysical investigations of increasing complexity and scale. Ultimately, the goal of these efforts is to maximize return on investment, whereby increased investigation costs at the design phase are offset by reduced uncertainty regarding subsurface conditions, leading to reduced cost overruns related to change orders and unforeseen site conditions during construction. These objectives are consistent with the recent Every Day Counts (EDC) initiative to incorporate Advanced Geotechnical Methods in Exploration (A-GaME) into routine engineering practice. Caltrans is an implementation partner of the A-GaME initiative, and Caltrans’ practices represent a model toward the institutionalized geophysical site characterization practices for other transportation organizations. The authors provide a retrospective on 70 years of experience with geophysical applications for transportation infrastructure, with examples and observations on potential future direction of the industry.

By Lyle F. Smith

With the demand for larger diameter raises under all ground conditions and the increasing price of drill rods and operating costs, it was evident that there was a need for a raise borer with a variable-speed drive and fast-response torque limiting control. The raise boring machine described in this paper was developed after several years of market research and discussions with mine operators and construction contractors. This paper discusses the Ingersoll-Rand raise borers with the solid-state controlled DC motor drives. These machines have gained wide acceptance in the five-year period since being placed in operation and are designed to accommodate the range of raise diameters and lengths most required today.

Jan 1, 1978

By Daniel C. Boteler

Five lignites from the northern Great Plains province were carbonized at temperatures from 500° to 1,000° C in a bench-scale unit. A replicated Greco-Latin square experimental design was employed to allow testing of four independent variables at five levels. Independent variables investigated were temperature, source of lignite (mine), weight of charge, and moisture content of charge. Dependent variables were char yield, tar yield, light-oil yield, tar plus light-oil yield, carbonization gas yield, and carbonization gas heat yield. An analysis of variance indicated that, at the 99-percent confidence level, the independent variables of carbonization temperature, source of lignite, and weight of charge were significant for yields of char, tar plus light oil, and carbonization gas, whereas moisture content was only significant for carbonization gas yields. At the 95-percent confidence level, moisture content significantly influenced the carbonization gas heat yield per pound of lignite charge and the yields of dry tar plus light oil. All dependent variables were determined on a moisture- and ash-free basis. Multiple regression equations for predicting seven different factors of carbonization yields as functions of carbonization temperature and initial composition were developed using computer techniques. Equations for yields of char, tar plus light oil, and carbonization gas were compared with equations previously developed by others at the 500° C level.

Jan 1, 1970

By J. B. Greenwood

The paper point out some reasons why contract mining should not achieve the same success in Latin America as it has in Australia. In this sense, any reasons are: the size of operation, mining industry employees bonus scheme, the privatization of nationalized mining assets, general sales tax and the mining unions. Therefore, great deal depends on the attitude or "mindset" of a company's employees. lt is strongly my view that the attitude with which a contractor approaches a job will give rise to a superior mindset amongst its employees when comparad to those from most mining companies. The value of this cultural difference is significant and should never be underestimated. lmportantly, it doesnot only manifest itself in a more productive workplace: it is invariably the case in Australia that the safety achievements of contract miners are superior to those generally expected from the mining industry at large.

Oct 6, 1999

By A. B. Holland-Batt

Following a relatively static period in the 1960s and 1970s when incremental development rather than innovation was the norm for gravity separation, the last 15 years has seen a number of new developments in this area. The paper briefly reviews the traditional gravity separation techniques and then examines the newer developments such as centrifugal separators. Particular emphasis has been placed on novel devices or improvements that offer either better control or improved performance.

Jan 1, 1998

By J. S. Carman

As with the slogans of Madison Avenue, catch words or phrases frequently become topical. Much is heard these days of the confrontation between governments of developing countries and international mining capital. In actual fact, sadly there are too few cases of anything as positive as confrontation because such an action at least signifies a dialogue which may begin badly but end up fruitfully. Instead we have in general a climate of indifference and fear with the mining companies of note marking off most of the developing world as being unsafe for investment. There is an unreal air to this damaging impasse. The common sense and objectivity which are prerequisites of positive action are lost in a swirling cloud of mythology, embraced largely by governments. Let us examine some of the dangerous misconceptions.

Jan 1, 1977

By Z. Zhang, M. -Y. Liu, X. -G. Chen, F. Breton

"The microstructures of AlSi10Mg foundry alloy in permanent mould (PM) and high pressure vacuum die (HPVD) castings were analyzed and compared. The as-cast microstructures of two castings mainly consisted of eutectic silicon particles, primary Mg2Si and Fe-rich intermetallic phases. The surface layer in HPVD castings, which has a unique feature and different structures, was carefully characterized. The dimension variation of microstructural phases along the cross section in PM samples is less than that in HPVD samples, although the size of microstructural phases in PM samples was much larger than that in HPVD samples. The mechanical properties of PM and HPVD samples were evaluated on as-cast and T6-treated conditions. The tensile properties of HPVD castings are remarkable better than those of PM castings on the as-cast condition. The T6 heat treatment greatly improves the tensile strength of PM castings while it has limited impact on the tensile strength of HPVD castings.INTRODUCTION The AlSi10Mg alloys are widely applied to the high pressure die casting (HPD) and high pressure vacuum die casting (HPVD). In the HPD process, the melt is injected into the die cavity under a high speed (30–50 m/s in the gate velocity for aluminum alloys), and solidified under a high pressure (up to 200 MPa in the cavity) and with a high cooling rate (up to ~103 Ks–1) (Gourlay, Laukli & Dahle, 2007; Ji, Wang, Watson & Fan, 2013). This results in a unique microstructure feature that is different to other casting processes under gravity. One major concern in HPD castings is porosity due to trapped air in the cavity (Ji et al., 2013), which seriously restricts the application of a heat treatment on the improvement of mechanical prosperities because of the formation of blisters on casting surfaces. For the process improvement, the high pressure vacuum die casting was developed in 1980s (Uchida, 2009). In this process, the melt is injected into the die cavity under reduced pressure (vacuum), which greatly reduces gas porosity in castings due to effectively avoiding the trapped air. Consequently, HPVD castings are heat-treatable without the formation of blisters on castings surface during heat treatment. The HPVD process has been widely applied to produce high quality structural castings in recent years attributed to reliable vacuum system development (Uchida, 2009). However, the microstructure features of HPVD castings are not systemically characterized yet."

Jan 1, 2018

"Real-time, on belt analysis of minerals is becoming increasingly important and critical in modern operations, especially in the mine-to-mill. Prompt gamma neutron activation analysis has long been utilised for real-time elemental analysis in bulk materials, with Scantech's GEOSCAN being the instrument of choice in the minerals sector. Working in the minerals space for 15 years, the GEOSCAN has been successfully implemented in a wide range of minerals applications including iron, copper, lead-zinc, manganese, phosphate and more, and it caters for the very high demands and increasing requirements of a contemporary processing facility. An area of focus has been on increasing the analysis frequency to allow for rapid analysis results with the same high degree of accuracy typically expected of the GEOSCAN. This paper discusses the underlying research and technology that has enabled such rapid analysis and presents a range of examples using a thorough statistical approach on real production material, demonstrating achievable accuracy over a short analysis time, and dispelling common myths about the speed of the technique. Potential applications are discussed to conclude the paper.INTRODUCTION Technology and the information it can provide plays a critical role in the evolving modern mineral processing landscape. The importance of technology to analyse various features of ores and concentrates being processed is obvious, and recent years has seen the advance of numerous technologies to provide a variety of real-time measurements on conveyed material flows. From sampling apparatus to particle size analysis to weight and density meters to full elemental analysis, the availability of information enables a variety of improvements in the process leading to improved efficiency and increased revenue. To maximise the potential benefits, access to real-time information is imperative, and rapid updates of information become necessary to make appropriate process control decisions based on the most relevant and up-to-date information."

Jan 1, 2017

By H. B. Sahu, N. M. Mishra, D. C. Panigrahi

The paper presents the development of a spontaneous heating liability index (SHLI) of coal based on a mathematical approach. The parameters for the calculation of this index have been determined by differential scanning calorimetric studies. Thirty-one coal samples representing both fiery and non-fiery coal seams of different ranks have been collected from different Indian coalfields and their SHLI values have been determined. In addition, the susceptibility of these samples to spontaneous combustion has been ascertained by standard crossing-point temperature measurement. The moisture percentage of all the samples has been obtained by proximate analysis. A comparative study between SHLI and crossing-point temperature, along with moisture percentage, indicates that SHLI predicts the proneness of coal to spontaneous heating more accurately.

Jan 1, 2008