Search Documents

By Melissa S. Beauregard, Randall A. Pietersen

This study focuses on quantifying the effects of water infiltration on a full-scale energy pile system’s ability to meet the thermal demand of an HVAC system. Theoretically, an energy pile system should increase its thermal capacity after a rain event due to increased moisture content creating an increase in thermal conductivity of the surrounding soil matrix. The United States Air Force Academy has an energy pile research site consisting of 8 full-scale energy piles located below a shower facility. The local colluvium surrounding the piles allows for relatively high water infiltration during rain events. This study uses an 11kW Precision Geothermal Geocube to apply a thermal load on two single-loop piles. A weather station located south of the structure records atmospheric conditions. Results indicate that moderate rain events can caused up to a 23% increase in the system’s thermal exchange capacity. This change is due to the increase in moisture content near the surface, which penetrates to deeper soil layers with time. The time required for moisture to penetrate to greater depths and then dissipate in the soil matrix, explains why increased system performance is seen for over a week following the passing of a singular rain event. 1 INTRODUCTION With a “future-forward” focus, there is an ever-pressing economic and environmental need to use sustainable sources to meet growing energy needs. HVAC is typically responsible for 34% of the overall energy required by commercial buildings and 48% of the energy required by residential buildings (USEIA, 2009; USEIA, 2012). Energy piles are a low cost, sustainable technology that have been used to offset this energy demand incurred by a building’s space heating and air conditioning requirements. An energy pile consists of heat exchanging elements in a closed loop system integrated into a building foundation and connected to a ground source heat pump (GSHP). It is most common for these heat- exchanging elements to be constructed within a drilled shaft foundation due to both construction practices and geometric considerations. This system operates based on the principle that at a certain depth below ground (typically 4 meters) subterranean temperature remains constant at a value equal to the mean annual air temperature at a given location (Kavanaugh et al., 1997). This allows the soil to function as a heat sink for cooling operations and a heat source for heating operations when exchanged within this zone of relatively constant temperature. For the past 25 years, the implementation of energy pile technology in public, residential, and even large-scale architectural complexes has slowly expanded which has created an increase in research into the topic as a result (Brandl, 2006; Hamada, 2007; Sekine et al., 2007; Gao, 2008; Bourne-Webb, 2009; Stewart and McCartney, 2013; Murphy et al., 2014). When pile construction takes place beneath the groundwater table, soil is under fully saturated conditions, maximizing thermal exchange for a GSHP system. Under unsaturated conditions, however, changing moisture contents change thermal conductivity values in a soil, which affect a GSHP system’s ability to meet a thermal demand. The observational data presented in this paper apply to GSHP systems in unsaturated soil conditions.

Jan 1, 2019

By A. Brown

This report details work performed and results obtained in a study of the water management aspects of oil shale mining and retorting in the Piceance Creek Basin. Three specific sites were investigated, and optimal water management systems for both conventional and in-situ extraction processes were generated. Water-related legal and environmental constraints on development were identified and the water management schemes were developed in compliance with these regulations. Limitations on shale oil production implied by limited water supplies were evaluated. Potential Basin-wide effects of development were evaluated using a computer model, and mitigation strategies were developed. Recommendations for additional investigation and analyses were presented.

Jan 1, 1977

Adolph Greiner, Seraing, Belgium:—I have nothing special to add to Professor Hubert's paper except to say that there are some little things that it would be well to have corrected when the paper comes to be published. In dealing with the thermal efficiency of the engine, you will find that the 29.84 per cent. was a very high one. Professor Hubert has forgotten those engines built under the Cockerill type, but he has referred to them in Appendix 11. At our works at Cockerill we have built 63 engines, giving 63,000 h.p., and the other companies who have received licenses have built 113 engines, making 103,000 h.p., and aggregating 176 engines and 166,000 h.p. Eight years ago I had the pleasure of giving to the Institute the results obtained up to that time. Since then a good many engines have been constructed. In 1898 I thought a blast-furnace producing 100 tons of pig iron would allow 3,000 h.p. Professor Witz and Professor Hubert show that with the same production of pig the new engines take 3,800 h.p. out of the gas. At present at Cockerill we make 700 to 800 tons of pig iron per day, and we hope to have 26,000 h.p. in a few years. At present we have only half of that in gas-engines, but we hope to have in five or six years all the gas out of these furnaces to the number of 25,000 or 26,000 h.p. Tom WEstGarth, Middlesbrough, England :—My contribution is not a paper in the ordinary sense of the word, because I am sure you will agree with me that what I have written is only supplementary to the other two papers. The notes are schedules of the larger-size gas-engines built by British engine-makers, of 500 h.p. and upwards. If you look at the schedules you will find that in England gas-engines have become quite ordinary motors for a good many purposes. It was at first thought that gas-engines were troublesome, and ill-

Jan 1, 1907

By K. H. Kretzschmar, M. A. Smith

A brief review of the rapid growth of ACT in Western Canada is presented. It is remarked that this rap-id growth has been accompanied by a heterogeneous approach to design. A more rational and consistent approach is suggested, together with the assumptions on which this approach is based. The operating history of some existing installations is discussed briefly, and conditions necessary for the continued growth of ACT are outlined.

Jan 1, 1960

In view of the increasing environmental regulations that have been promulgated all over the world in the last 30 years, non-ferrous smelters and refineries have learnt and adapted to treat effectively metals'-containing process waste streams that need to be bled from the plant. However, anions such as sulfates, chlorides and fluorides-presently not a major problem ?are coming under increasing scrutiny and need to be addressed in the near future. The current paper reviews options for waste water treatment with reference to: a) types of waste streams processed b) process chemistry c) discharge options d) recovery and reuse of water and e) solids disposal. Methods to obtain zero liquid discharge ?a possible solution to eliminate discharge of above anions and residual heavy metals- are discussed with case studies. The long term goal of any non-ferrous smelter plant should be to have a zero liquid discharge philosophy-an approach that would become an epitome of water reuse and conservation.

Jan 1, 2009

By John F. Papp

International and U.S. chromium material flow, losses, and environmental releases and transfers from mining through industrial processing, end use, and recycling are identified and quantified. Average (1983-92) U.S. consumption has been: metallurgical industry, 87 pct; chemical industry, 10 pet; and refractory industry, 3 pct. Average chromium content of aluminum, cobalt, copper, nickel, and titanium alloys and alloy, carbon, and stainless steel alloys was estimated. Anthropogenic chromium consumption was estimated for the cement and copper industries. N on-commodity cycle anthropogenic chromium mobilization resulting from U.S. fuel and fertilizer use was estimated. Commodity cycle anthropogenic world chromium loss from mining and primary consumer industry was estimated to be equivalent to about 56 pct of chromium contained in chromite ore production and represented a loss rate of 181 kt-Cr/Mt-CrOre. Chromium released to the atmosphere from natural and from anthropogenic sources were comparable in magnitude. Chromium released to soil was mostly from anthropogenic sources, and aquatic releases were all anthropogenic. Domestic product chromium losses exceed process losses by more than a factor of 10 showing the importance and potential environmental impact of post-consumer recycling. The location of historical and current domestic chromium industry processing sites in 23 States were reported. Chromium releases and transfers to the environment were estimated from 1973 through 2002 by primary consumer industry. A decrease in chromium releases and transfers to the environment was anticipated.

Jan 1, 1995

By Walter W. Kaufman

This User's Manual, extracted from information contained in the Final Report for the above referenced project, outlines test procedures to measure the braking capabilities of underground non-coal rubber-tired mining equipment. Methods to interpret test results, recommendations for safe braking capabilities, and basic techniques to improve braking systems and road surfaces are also discussed. Possible applications for runaway vehicle protective devices other than braking systems are reviewed. Also included is a listing of mining equipment and brake component manufacturers who supply the majority of equipment to the United States non-coal mining industry. In conjunction with this list of manufacturers, a general tabulation of brake related specifications appears for vehicles observed during stopping tests conducted underground.

Jan 1, 1977

By J. C. Loretto

The philosophy and detail of mill design in developing countries, where it is frequently difficult to obtain experienced, qualified supervision to operate the plant, are discussed. The resulting design suggests the desirability of simple units, with maximum visibility of equipment operation and material movement, which allow the minimal technical supervision to see the plant conditions prevailing. Information on plant conditions during periods of lesser supervision can be provided by the use of simple, low-maintenance recorders. Where the mill is intended for operation in a developing country, it is insufficient for the flowsheets and plant layouts merely to be drawn: the process metallurgist must pay meticulous attention to details that could ordinarily be left to the design detailing group. The design of this type of mill requires a knowledge of human engineering—of the type of individual who will operate and supervise the plant; probable changes in personnel should be taken into account. Details are suggested for coarse-ore handling, screens, feeders, secondary and tertiary crushers, conveyors, dust collecting, fine-ore feeding, grinding mills, conditioners, flotation, thickeners, filters, reagent systems, sand pumping, sampling, instrumentation, safety and construction

Dec 1, 1971

By A. C. Fieldner

The past full year of war has increased greatly the demand for virtually all kinds of fuel, and the Bureau of Mines research and service facilities have been extended to meet these unprecedented requirements. Liquid fuels, such as aviation and motor gasolines, are fundamental to modern warfare. Bituminous coal and anthracite are needed, not only to servo the expanded industrial program for which coal normally is used but also to replace natural gas, wherever possible, and fuel oil in the Eastern States, New England, and the Pacific Northwest. Railroad transportation with energy derived from coal is replacing much of the motor-vehicle transportation that has been stopped or curtailed to conserve rubber. Pulverized coal hoe been sound to be a satisfactory and cheaper substitute for fuel oil in metallurgical heating furnaces. Celloidal fuel - a mixture of coal dust and oil - may offer a partial substitution for curtain coal-burning equipment. Several industrial experiments have been made with this type of fuel. The expansion of the steel industry in connection with the war program has required a corresponding increase in the production of metallurgical coke and its associated byproducts - light oil, tar, ammonium sulfate, and surplus gas. If the war is of long duration and new reserves of petroleum are not discovered, wartime trends from fuel oil to coal probably will not be reversed.

Jan 1, 1945

By R. B. Massy-Greene

Project engineering and development is a process of optimisation of capital, operating and financial costs, and extraction rates in the light of current and forecast economic conditions for the sale of the product. The aim of the process is to maximize financial returns to the sponsors (project owners) within many often conflicting constraints. Thus, the sponsor's engineering and financial staff have a common goal, with performance measured in financial terms. Consequently, each group must be aware of, and responsive to, the constraints imposed upon the other. For financial staff, the increasing size and complexity, and escalating capital costs of new ventures have required them to seek finance in larger amounts, and by non-traditional methods. In addition, senior management are requiring indications of the availability of finance as a pre-requisite to a decision to commence project development activities.

Jan 1, 1982

By L. B. McConville

The general term "tar sand" has been used to describe sand containing varying amounts of dense, viscous petroleum. Deposits of tar sands have been found throughout the world, often in the same geographical area as conventional petroleum. The largest one by far is known as the Athabasca Tar Sands, and is located in the province of Alberta, Canada. Actually a group of three deposits, these particular sands underlie an aggregate area of more than 12,000 square miles. Current estimates place the contained raw petroleum at about 700 billion barrels, from which as much as 300 billion barrels of synthetic oil may be recoverable under presently developed technology. For comparison, this latter quantity is roughly equivalent to five times the combined total of U.S. and Canadian crude oil reserves. With the ever-widening gap between energy supply and demand, attention is being directed to all possible energy sources - both developed and underdeveloped - and certainly the Athabasca Tar Sand deposit is one of the more important ones to merit such attention. This paper will review some of the more significant developments and attempt to place in perspective the role that this source of energy could possibly be expected to play in the foreseeable future.

Jan 1, 1974

A compilation of papers presented at The Second WVU Conference on Coal Mine E1ectrotechnology in Morgantown, West Virginia on June 12 -14, 1974. Papers cover areas of electric power, electronic communications, detection and location of trapped miners, and electronic sensors and monitoring systems.

Jan 1, 1974

By Albert H. Fay

This glossary is publi~hed- by the Bureau of Mines as a contribution' to the mining literature in the belief that it will fill a long-felt need. It contains about 20,000 terms; these include both technical and purely local terms related to metal mining, coal mining, quarrying, petroleum, and natural gas, and metallurgical works; names of useful, important, and common minerals and rocks; an<lgeological terms. It presents in one comprehensive volume the available standard, technical terms relating to the mining and mineral industry, as well as provincialisms that have been or are now in use in English-speaking countries. The glossary also includes many terms relating to ceramics and the clay industry, glass making, foundry practice, railway and building construction, electrical installation and power-plant equipment, and chemical terms relating to metallurgical practice. Complete lists of terms for' each of these allied industries are beyond the scope of this glossary. Paleontological terms, although closely associated with geology, are far removed from mining and metallurgical operations, and for this reason have been omitted. In a compilation of this magnitude, it is difficult, within a reasonable time to verify all definitions as to the latest usage. Much verifying was done and it is hoped that the best and latest definitions have been used. Reference to the publications cited will enable the reader to determine approximately the period when the definition was used. Definitions in use by engineers of high national or international reputation are given first preference. When definitions from different sources are the same, credit is given to the earlier author as being the original or nearest to the original source. Immediately following each term the name of the locality wherein the word is presumed to have originated or is widely used is given, where such information is available. The name of the author or source from which the definition was obtained follows the definition, and serves as a key to the publications listed. The terms selected from the various glossaries and publications examined have been compared with the Webster,

Jan 1, 1920

By J. F. Barkley

To aid in winning the recent world war, the Bureau of Mines conducted a National Fuel Efficiency Program, directed to commercial plants throughout the Nation, to save greatly needed fuel, a basic resource vital to industrial production. In planning this program it was realized that to accomplish a satisfactory reduction in fuel consumption in any plant, it would be necessary to reach, enthuse, and usually educate to some extent the actual operators of the various types of plant equipment. A major part of the programs consisted, therefore, of visits to plants and work with the operators, including a review with them of their operating conditions and of educational and guiding literature pertinent to the operating problems involved. Through a Nation-wide organization, local volunteer engineers served in making visits to local plants. Each cooperating plant appointed an employee as the "waste chaser," who headed the work of saving fuel in that plant. The educational literature was designed to interest the operator, as well as serve as a guide in eliminating waste of fuel. Volumes have been written on many subjects relating to the saving of fuel. Writings of the treatise type contain considerable good information but do not have wide appeal and probably will be read only by a few studious operators. The problem is not one of getting clown on paper everything that the experts know and would like to have the operator know, but rather to write something that will actually interest the operator and stimulate him to action. Past experience led to the adoption, therefore, of the "quiz-sheet" type of writing, using a quiz sheet of not more than two pages for any principal item. The results obtained during the National Fuel Efficiency Program in many types of plants further demonstrated that the short quiz sheet is satisfactorily appropriate and does accomplish results. Each sheet was prepared and checked by many engineers expert in the particular subject matter of the sheet. Committees of men with much experience in the manufacture and operation of equipment and in the

Jan 1, 1947

By J. Frederick Stampfer

Current certification testing of self-contained breathing apparatus includes tests with human subjects wearing the apparatus while exercising. During these tests, certain apparatus variables are measured during rest periods. Because of concerns that the present tests may not accurately simulate the stresses to which an apparatus is subjected in the field, the Bureau of Mines proposed new human subject tests. It was also felt that different measurement techniques would supply more reliable data on the apparatus response to these stresses. The Los Alamos National Laboratory was asked by the Bureau to evaluate the proposed tests and monitoring techniques. The major conclusions derived during this study are these: (1) The proposed tests are not too physically demanding. (2) As long as human test subjects are used, a minimum subject weight should be required for certification tests. (3) Important apparatus variables are the breathing resistance, temperature, and carbon dioxide and oxygen concentrations of the inhaled gas. (4) Continuous monitoring should be used, rather than monitoring only during rest periods. (5) New pass/fail criteria based on realistic estimates of the user&apos;s physiological requirements, as tempered by present and future engineering limitations, are needed. (6) When available, breathing machines, rather than human subjects, should be used for most certification testing. (7) A more realistic ergonomics test than that proposed is needed. (8) A gas leak test for the system and a facepiece leakage test are also needed.

Jan 1, 1983

By B. S. Xakalashe, I. J. Geldenhuys, B. Bowman, M. W. Erwee, G. A. Venter, J. Zietsman, C. Sandrock, Q. G. Reynolds

Understanding the behaviour of plasma arcs is an important part of the design and operation of direct current electric arc furnace smelting processes, which are used in the industrial production of many metallurgical commodities. In recent years numerical and computational modelling techniques have begun to illuminate the complexity of arc behaviour and how it is deeply connected to the thermodynamic and physical properties of the arc plasma. Plasma properties may be estimated from first principles using statistical mechanics methods, but this requires as input some knowledge of the composition of the gas phase that occurs over the process during smelting. In this paper the authors describe a workflow using thermochemistry software to predict the expected gas phase composition through a given process, followed by plasma property calculations using an open-source software tool that has been in development for several years. This tool, 'minplascalc' has been in development for several years and is also described in detail here. The workflow is then applied to the calculation of plasma properties of interest for a variety of historical and current pyrometallurgical processes, and the results are compared. The plasma property data are published in an open-access database for general use.

Mar 4, 2025

By Michael J. Lawrence

"The VALMIN Code was developed and formally adopted by The Australasian Institute of Mining and Metallurgy (AusIMM) in 1995 and a revision was issued in 1998. The VALMIN Code applies to all relevant reports under the Australian Corporations Law, including submissions to the Australian Stock Exchange (ASX) and the Australian Securities and Investments Commission (ASIC).The VALMIN Code and Guidelines sets standards for the preparation and commissioning of independent assessment and/or valuation reports on mineral and petroleum assets or mineral and petroleum securities.It is mandatory for AusllvI:M's members to follow this Code in these relevant circumstances and failure to do so will result in serious sanction of the member by the Ausllvllvfs Ethics Committee. Public support for the use of this Code has been given by regulators (ASX/ASIC) and market participants ( eg major accountancy firms). It is also endorsed as a guide to general best practice in project assessment and valuation.This paper will discuss how the VALMIN Code has worked in practice over the past few years. It will also examine areas where the Code could be improved and how it could form the basis of a new Canadian Code for mineral property valuation."

Jan 1, 2003

By Andrew A. Cochran

Laboratory-scale research was conducted by the Bureau of Mines to develop a new process for treating electroplating and other wastes. Various acid and alkaline cyanide wastes were combined under controlled conditions to neutralize the wastes and to almost completely precipitate the metals and cyanides. The metals were subsequently recovered for recycling; the cyanides can also be easily recycled. The process was successfully used to treat the major types of electroplating and etching wastes, containing Cd, Cr, Cu, Ni, and Zn, and to treat both concentrated and dilute wastes. The economic aspects of treating concentrated electroplating, etching, and anodizing wastes are especially attractive because of the low cost of mixing two wastes, the high value of the recovered metals, and the simplicity of the recovery procedures. The filtrates from the waste-plus-waste step were relatively harmless compared with the original wastes and met Public Health Service standards for free cyanide content. Free cyanide ions were not detected in most of the filtrates; the limit of detection was 0.03 ppm. Only small amounts of HCN were produced during the neutralization; the HCN was collected and neutralized.

Jan 1, 1974

By Mark W. Booth

THIS paper deals with the subject of inbye power as the mechanical . engineer sees it, and invites discussion, particularly from the electrical engineer. At the outset, it will be necessary to clear the ground a little by some definite statements. In this question of compressed air versus electricity for the transmission of power and driving of machinery in underground workings, we must see that there are definite fields that compressed air on the one hand, and electricity on the other, can fill to much greater advantage than the other, and in which there can be little or no direct competition, at least for the present. It is under conditions where these fields overlap, and as to where the line must be drawn between the two, that the respective merits of each must be considered. Steam was the first means used to transmit power from the surface of a mine to drive underground machinery, and so long as distances were short and means possible to ensure fairly efficient use of the steam, and where the fire hazard was not in evidence, it gave fairly efficient service. I have in mind an instance during my own connection with the mines-a duplex pump at the shaft bottom at Princess colliery, driven by steam, and which used the steam compound and condensing; and, but for the mechanical difficulties, it was a not inefficient proposition. The steam was taken direct from the surface boiler-plant through a line down the shaft, and used directly at the pump, being in effect a straight conversion from coal to steam to work done. It was the mechanical arrangement, and failure of the pump in that direction, that led to its removal and replacement by something better in the way of an electrically driven turbine pump. Given modern mechanical arrangements, such as a steam-turbine drive on a high-speed turbine pump, and all other parts made in accordance with best practice in the art of steam generation and use, a steam-driven unit fully as economical would have been obtained. But the central electric supply station, and all that that means or promises (not always the same), turned the scale against steam.

Jan 1, 1936

By Karl A. Gschneidner

The magnetocaloric effect has been known for 120 years and has been utilized for cooling about 70 years. But in the last four years significant advances have been made to show that magnetic refrigeration is a viable and competitive cooling technology. Most of the work has focused on reciprocating devices, but rotary apparati are being developed. To date the magnetocaloric properties have been characterized for more than 200 materials. The magnetocaloric effect behaviors have been classified into three types of behaviors. The most common one is found in magnetic materials which exhibit a second order magnetic phase transition. Magnetic materials which exhibit a first order magnetic phase transition account for the second group of materials. Materials which exhibit multi-magnetic phase transitions make up the third group. The best candidate materials for magnetic cooling over the range from -4 to -1 350 K are also presented.

Jan 1, 2002