Search Documents

By Charles D. Litton

Laboratory experiments were conducted to determine the responses of a prototype smoke detector and a commercially available photoelectric smoke detector to smoke particles generated from various combustion sources. The prototype smoke detector combines optical scattering measurements with ionization chamber measurements in order to reduce/eliminate nuisance alarms due to the presence of airborne dusts or diesel exhaust particles. The commercially available smoke detector is designed for use in harsh environments where airborne dust represents a major problem due to both nuisance alarms and detector contamination. In the experiments, the responses of the two detectors were measured when exposed to smoke particles from the exhaust of a diesel engine and from a variety of fire sources, including wood, coal, styrene butadiene rubber, and No. 2 diesel fuel. For the solid fuels, data were obtained for both smoldering and flaming combustions. This report describes the experiments, their results, and the use of these results as they apply to early-warning fire sensors capable of the rapid and reliable detection of fires in atmospheres that may or may not be contaminated by either airborne dust or the products produced from diesel engines.

Jan 1, 2008

By James A. Finch, Stéphanie Somot

"The self-heating facility developed at the Noranda Technology Centre [Rosenblum and coworkers, 2001; 1995] has now been established in the Department of Mining, Metals and Materials Engineering at McGill University. A research program into mechanisms has been initiated (with support now from four industrial partners under Camiro). The first investigation is into the role of pyrrhotite (Po), the most commonly suspected mineral to trigger self-heating. Following a standard experimental protocol, self-heating was assessed on samples of Po mixed with sand as an inert material. With increasing Po content, self heating progressively increased but, interestingly, the samples visually appeared less and less oxidized. A high Po content, it was hypothesized, may give a more reducing environment favouring formation of H2S. The presence of this gas could be significant as it has a high exothermic heat of reaction with oxygen. The system was modified to test the hypothesis by including copper pieces and copper sulphate to react with (and therefore reveal) the gas as copper sulphide. Evidence is presented in support of H2S production, which to our knowledge has not been shown before and introduces a potentially important avenue of investigation into self-heating mechanisms.INTRODUCTIONSelf-heating of sulphide minerals poses potential environmental and safety hazards in mining of ores, and storage and transport of concentrates. While some conditions are known to be critical, the reactions remain poorly understood making self-heating difficult to predict and control.A major advance in measurement was introduced by Rosenblum and co-workers [Rosenblum et al., 2001; Rosenblum and Spira 1995]. A self-heating assessment method was developed and applied to various sulphide-bearing materials The method is based upon automated calorimetric cells with data acquisition, now available to McGill researchers and which have been used for the study reported here."

Jan 1, 2006

By J. O. Pitts

"Background The preponderance of Canada's coal resources is located in areas remote from high demand domestic users and at some significant distances from deepsea ports. This places great demands on the transportation system and has forced the coal and the transportation industries to adopt highly efficient methods of handling the product and hauling it to market position. Most of the coal not consumed in minemouth thermal power stations is carried by rail over lines operated by the two transcontinental railway systems, Canadian National and Canadian Pacific. These rail networks are extensive and have the advantage (as compared to most other North American railways) of being able to handle coal movements from origin through to destination without interchange to other rail carriers. Coal SourcesWith exception of the coal produced in Cape Breton, Nova iScotia, all the significant shipping volumes in Canada emanate ifrom mines located in the three most westerly provinces. Figure I ishows the geographic distribution of the major mining operaitions shipping coal to domestic and export markets. The prinicipal routes and the tonnages carried (1980 calendar year) are ialso indicated. iThe 1980 shipping data are summarized in Table I. Saskatchewan lignite began moving from Bienfait to Thunder Bay by CP Rail unit trains in mid-1981 at the rate of one million tonnes per year. The product is handled through Thunder Bay Terminals and delivered directly to a nearby Ontario Hydro electrical generating station."

Jan 1, 1985

By L. Barnewold, A. Merchiers, M. Pütz, P. Jeschke, M. Dammers

The mining industry faces many difficult challenges, for example, lower ore grades, smaller and deeper deposits, and longer transportation distances. In the past, there have been remarkable innovations in both equipment and the types of mining methods for which it is used, which have resulted in economies of scale. This has led to an increased use of bulk mining methods, like sublevel and block caving, which has increased productivity and reduced costs. Haulage alone plays a major role. Current haulage techniques are a significant cost driver, which account for between 15 and 30% of the overall capital investment (capex) in a mine and are an increasingly part of the operating costs (opex). The paper introduces a simulation tool of main haulage system in underground mining. Therefore, performances and the costs of the three most common underground main haulage systems, rail, truck, and conveyor, are calculated using a developed modeling tool. The tool was applied and validated in a case study carried out with the LKAB Kiruna Mine in northern Sweden.

By S. H. Katz, J. J. Bloomfield

Fires in zinc dust have sometimes given particular trouble owing to their resistance to extinguishers and the liability of explosions . Similar problems , notably with aluminum dust* , have previously been subjects of investigation by the Bureau of Mines .

Mar 1, 1922

By R. R. Sayers

"The number of investigations reported during the past year indicates that control of the health hazard due to abnormal air conditions is still a matter of serious consideration in the mining, metallurgical, and allied industries.Australia. - In an investigation into the health and working conditions of employees in the mining industry of Tasmania and Victoria3, it was found that although pulmonary tuberculosis may occur early in life, silicosis is e disease of slow evolution and does not appear frequently under the ace of 40. A period of at least ten years in the industry was found necessary to produce silicosis, and in no case was the disease found in those who had not worked underground. A very high incidence of silicosis was found in all fields among those who had worked underground 20 years and longer. There was some evidence that silicosis complicated by tuberculosis may occur earlier than uncomplicated silicosis.England. - In a paper presented before the Section on Occupational Diseases of the British Medical Association, Dr. E. L. Middleton, the medical inspector of factories, called attention4 to the occurrence of silicosis in various industries throughout the country.punitive on some quite harmless industries. Thus Middleton says: ""Where the amount of dust is small the action of the phagocytes is likely to be effective, but where it is great . . ."" What dosage is indicated by ""small"" and ""great"" in this connexion? If the meaning of ""small"" were known, would it be correct to go on to say, as he does, ""each successive dose of silica produces a summation of effects""? Then, again, would it be fair to say ""a comparatively brief period of exposure may be the only determining factor""? What, in minutes, hours, or days per week, per month,' or year, is intended by ""a comparatively brief period""? ""Intermittency of the process"" is another expression used in summing up the reasons for and against a standardization of air purity by a gravimetric process or enumeration of the particles; the arguments against such a standardization are, by Middleton, considered strong, but they are by no means convincing to us. A standard has been accepted in respect of the amount of lead in milligrams per 10 cubic metres of air; Dr. Ronald Lane showed in another paper read that adherence to this makes the occurrence of poisoning highly improbable. Mavrogordato has placed on record figures of silica dust at different stages of the improvements in the workings of the Rand mines, and such a control is in constant operation in them today.We emphasize these points because apparently the Government has taken the unusual course of legislating first and postponing inquiry to a later date, as in the ""Various Industries (Silicosis) Scheme, 1939."" The insurance companies also have a considerable interest in the matter of compensation for the silicosis risk. Where exposure - as in the refractories industries, the grinding industries, sandstone industry, and pottery industry - is day in and day out, they rightly demand a premium far higher than for any other disease scheduled under the Workmen's Compensation Act - 5 per cent on the wages bill. row every industrial employer, such as the paint and varnish manufacturer, who has a sack of crushed silica in his store .room, from which he extracts once a week enough to make a paste With spirit and add to his other ingredients in order to give them the necessary ""bite,"" becomes involved, and may have to abandon the use of the material or pay 8 per cent on his wages bill for an absolutely negligible risk.. For meting out justice standardization seems urgently called for."

Feb 1, 1930

By Raja V. Ramani, Robert L. Frantz

"In response to the U.S. Bureau of Mines (USBM) Request for Proposal (RFP) for "" the establishment of a Generic Mineral Technology Center (GTC) in Respirable Dust,"" the Mining and Mineral Resources Research Institutes (MRIs) at The Pennsylvania State University (PSU) and West Virginia University (WVU) in association with participating MRIs at Massachusetts Institute of Technology (MIT), and the University of Minnesota (UMN) have prepared the comprehensive research program described herein. Michigan Technological University (MTU) joined the Center as an affiliate after its inception. This program was developed with recognition of the stated objective of the Federal Mine Safety and Health laws which is to "". . . permit each miner the opportunity to work underground during the period of his entire adult working life without incurring any disability from pneumoconiosis or any other occupation-related disease . . . .""Exposure to respirable contaminants in mine atmospheres has long posed a serious hazard to miners. The control of these hazards, some of which can have sudden and catastrophic consequences and some others, slow and long enduring, has been a major concern for labor, management and the government. This concern has manifested itself in four mechanisms of control -- (1) regulatory control through minimum standard setting by the passage of mine health and safety laws, (2) engineering control through design and operation of mines according to the best recommended practices, (3) interaction of dust and lung control through periodic physical examinations, wearing personal protection devices, etc., and (4) legal and social control through workman's compensation laws for occupation related health deterioration."

Aug 31, 1989

By Arthur Zentner

THE essentials of the electrolytic zinc process, as now used in commercial plants, date back to work done by Letrange in 1881. He used sulfuric acid to leach roasted sulfide and ,oxide ores, purified his solution very much as we do now, and electrolyzed the purified zinc sulfate solution. Ten years later Hoepfner developed a process using chloride solutions, and built three plants. One in England operated until 1924 in one of the works now merged in the Imperial Chemical , Industries, Ltd. Ashcroft built a plant in 1898 in the Broken Hill district of Australia. He used both chloride and sulfate solutions.. While his work failed, the aid his published results have been to later workers has made him an outstanding contributor to the de- velopment of the electrolytic zinc process. A good deal of work was done in the following years, aiming to electrolyze zinc chloride solutions and fused zinc chloride. Quite a bit of work on sulfate solutions was also done in the last years before the war. With the outbreak of the war, metal demand and rise in metal prices provided the stimulus which resulted in the remarkably rapid commercial development of electrolytic zinc. In this last period of development, all the work brought to commercial fruition has been with sulfate solutions. The high-density process, or the Tainton process, is used, as you know, in the Sullivan electrolytic zinc plant at Kellogg, Idaho, and will be used in the Evans- Wallower plant now being built at East St. Louis. The low-density process is used by the other plants now operating in the United States and other countries. There are now in operation and under construction four electrolytic zinc plants in the United States, two in Canada, two in Italy and one each in Australia, Rhodesia, Poland, Norway and Germany.

Jan 1, 1929

By P. G. Kovalchik

Recent research conducted by NIOSH, Pittsburgh Research Laboratory showed that electrical current levels permitted under present regulations may not limit cable temperatures to less than 90°C in reeled trailing cables. Reeled cables, tightly wrapped with many turns, all carrying current in an enclosed space, can become overheated due to poor heat transfer. This overheating can cause the cable insulation to soften and become easily damaged. The damaged insulation reduces the life of the cable and can lead to shock, electrocution, and mine fires. This paper describes a method of measuring the conductor temperature of mine trailing cables during normal operation. The temperature is measured using a 50/125 micrometer Graded Index Multimode Optical Fiber located in the center of the metallic conductors. Distributed temperature measurements are made using an Optical Time Domain Reflectometer (OTDR). This system is capable of measuring temperature with an accuracy of plus or minus one degree centigrade over a length of 4 km at 1-m intervals. With this unique way of measuring temperature, tests can be conducted simulating actual mine conditions and provide important data to allow MSHA's Approval and Certification Center to develop approval criteria for cyclically rated reeled machines.

Jan 1, 1998

By Simon C. Dominy, Alwyn E. Annels, Paul Wheeler, Suzanne P. Barr, G. Simon Camm

Narrow veins are an important world-wide source of silver, tin, uranium and particularly gold. To potential ?nanciers, this style of mineralization is viewed as high risk because of the often relatively small resource involved and high cost of estimation. In many cases diamond core drilling will not enable resource estimation beyond the inferred and indicated categories. Exploratory under-ground development is required to de?ne measured resources. The de?nition of geological and grade continuity are major factors in narrow vein assessment. A measured resource must be based on strong geological and grade continuities. Narrow veins, generally less than 3 m wide, are complex geological phenomena, which commonly display unpredictable geometry and grade distribution. Variations in structural continuity, dip, strike, width, mineralogy and speci?c gravity are common. Veins may be composite, with ore-grade mineralization restricted to a speci?c structural domain. Branches, intersections and braided zones are common features. Potentially high-grade zones are often localized within ore shoots, which are surrounded by barren/low-grade regions. Resources must be determined as closely as possible to reality and re?ect the distribution of the commodity in the rock. Estimation has three main requirements: (1) geological study to determine orebody nature;(2) estimation of tonnage and grade, and (3) the presentation of this information using a classi?cation that is clear, unambiguous and bankable. Estimation methods employed are either classical or geostatistical; however, classical methods are often used because of the dif?culties in applying geo-statistics. Grades generally show a strong positively skewed distribution testifying the presence of high-grade values. Problems exist in the applicability of cutting outlier values risking over- or under-estimation of grade. It is generally believed that where resource estimates are in error, poor geological control is usually the cause. Overestimation can lead to the closure of a mine through lost revenue and capital. An understated estimate can result in an opportunity missed for pro?t and/or greater economies of scale. De?nition of reserves involves the consideration of economic and engineering data, to decide which part of the resource is economically mineable. Geology plays a similarly important role at this stage in the assessment of likely mining method, dilution, recovery etc. Throughout resource/reserve estimation, it is crucial that the amount and quality of the data and the geologist’s experience are relevant. The impact of geological understanding on estimation is often undervalued or assumed to be of lesser importance than ?nding grades and tonnages. This paper discusses the geology of narrow vein deposits and the importance of geology in their evaluation.

Jan 1, 1997

By P Klaric

Drive stability is critical in block/panel cave mining. The production levels of these mines are required to remain operational for the entire life-of-mine which can be in excess of 30 years. It is therefore necessary to produce high-quality drives to ensure sustainable mine productivity. In order to improve the quality of drives and pillars, this gold mine instigated a project to optimise their development blasting. The initial aim was to reduce the level of overbreak in development mining, which was averaging approximately 18 per cent. The benefits of controlling overbreak not only included an increase in the integrity of the drives but also a decrease in load and haul and ground support costs. Through focusing on the optimal blasting of the perimeter holes, overbreak was reduced to 4.5 per cent. The project’s focus then moved to drill and charge designs for development faces. In optimising these designs, it was anticipated that improvements in the development mining cycle would be achievable.CITATION:Klaric, P, 2015. Improving drive stability through efficient development blasting design and practices, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 327–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By R. B. Nourse, R. Hundermark, B. Masters, H. Joubert

The new 30 MVA slag cleaning furnace at Waterval Smelter, Rustenburg Platinum, South Africa, has been in operation since 10 March 2003. The furnace design and operation face a number of challenges including a wide variety of feed materials and resulting bath conditions. Furnace feed varies in combinations of granulated Waterval Ausmelt Converter Slag (WACS), hot fed Peirce-Smith converter slag, concentrate and reverts. Coke is added as reductant. The resulting slag composition varies considerably and regularly. For the case feeding WACS an almost pure fayalitic slag (60%+ FeO, 30%+ SiO2) with a very low viscosity results. Due to the widely varying slag conditions, including a superheated fayalitic slag with high fluidity, a robust sidewall design is required adjacent to the slag bath. For this reason the furnace sidewall is equipped with Pyromet's MAXICOOL® high intensity copper cooling system. The design and installation of the copper coolers as well as tap holes are discussed. To cope with the variation in bath conditions and high slag superheat (350°C when tapped at 1650°C), the copper coolers are capable of removing peak sidewall heat fluxes above 500 kW/m2. Feedback is included on the performance of the Pyromet MAXICOO® copper cooling system for the first two years of operation. The paper further includes an overview on the design and performance of the tap holes, furnace shell, furnace roof and copper slag spouts.

Jan 1, 2005

By Athena C. Denivo, Pablo V. Lopez, Michael McMaster, Sissy Nikolaou, Alfred H. Brand

"The paper presents the history of development of the United States Tennis Association (USTA) site, focusing on geotechnical, geoseismic, and foundation engineering challenges associated with it. The site is located at the Flushing Meadows Corona Park area of Queens, New York. Now home to the Billie Jean King National Tennis Center (BJKNTC), the site used to be a biologically rich, tidal salt marsh that extended south from Flushing Bay and overlaid an ancient buried valley. In early 20th century, Brooklyn Ash Co. was contracted to fill the marshland with cinders and furnace ashes. F. Scott Fitzgerald describes the “Valley of Ashes” as “a fantastic farm where ashes grow like wheat into ridges and hills and grotesque gardens; where ashes take the forms of houses and chimneys and rising smoke, and finally, with a transcendent effort, of ash-gray men who move dimly and already crumbling through the powdery air.” In 1939 the site was leveled and filled to host the World’s Fair and refilled again for the 1964 World’s Fair.The USTA moved to the site in 1978 and in mid-1990’s constructed the 23,000-seat Arthur Ashe Stadium (AAS). Currently, USTA has a Strategic Vision Plan venue with several interconnected construction projects including buildings, infrastructure upgrades and improvements to site circulation. In addition to a historical walkthrough, the authors will discuss technical challenges of supporting these developments through layers of fill, thick organic silty plastic clays and regional varved soils with bedrock found 300 to 400 feet deep. The subsurface is not only a weak foundation medium, but is susceptible to large amplification of seismic waves propagating from the bedrock during earthquakes. The developments are usually founded on project-specific pile foundations that carry static loads in deeper layers and accommodate lateral demands and performance objectives. Engineering innovations from the most recent development, the roof structure over AAS, will be discussed."

Jan 1, 2016

By D Ray, D Brett

A clay-capping trial was established in 1996 on Magazine Dump at the Mt Lyell Copper Mine. The trial was initially constructed under the Mount Lyell Remediation Research and Demonstration Program, a co-operative venture between the State and Federal governments. The detailed engineering design for the clay cover included the following features; reshaping and compaction of dump batters, 5 m vertical bench interval, overall side-slopes of 2.5:1, emplacement of clay in four 150 mm lifts, compaction by a 10 t vibrating roller or ætrack rollingÆ on batters with density testing for quality control. A small section at the base of the dump ( The trial also generated certain unexpected findings. Field permeability tests on the cover yielded uncertain results and oxygen remains available throughout the dump. The flow data indicate that, while total outflow has decreased as a result of storm shedding, inputs from groundwater and batter infiltration are still significant. Outflow during the driest weeks of the year may have risen following capping. Detailed assessment of the data is hampered by insufficient pre-capping information; however, there is a possibility that conductivity flux emitted when flows in the receiving environment are at their annual minimum is unchanged or worse post-capping.

Jan 1, 2003

By Steve Dillingham

The origin of the written blasting log or shot report can likely be traced back to the earliest annals of blasting and record keeping. These records were, for the most part, a way of checking inventory, production progress, or billing, and not necessarily designed with the intention of being used as a legal document in a court of law. As our litigious society has evolved to include far reaching regulatory requirements, however, the blasting log has developed to support and aid in the defense of the common blaster from blasting lawsuits by providing a comprehensive written report of his or her actions.

Jan 1, 2002

By M Berry

Many mining companies routinely use benchmarking to review their operational activities and associated costs. The aim is to measure operational performance against industry norms, and identify areas where a company is performing better or worse than industry best practice. The goal is continuous improvement.In general, mine technical services, including mining geology activities, are not routinely benchmarked. There are exceptions, such as the cost of drilling per metre and the average discovery cost per unit of metal, but generally mining geology activities are only included indirectly in mining benchmarking studies.Aspects of benchmarking can play a critical role in assisting mining geologists to improve the efficiency and effectiveness of the services they provide. Industry norms for many generic mining geology functions have not been developed and measured, and therefore it is impossible to use external benchmarking to assess performance against other mines. But when used in parallel with quantifying the value of mining geology functions and establishing strategic goals for the team, key components of benchmarking methodology can provide essential feedback on how a team is performing against these strategic goals.CITATION:Berry, M, 2014. Benchmarking – does it have a role in improving the performance of mining geology?, in Proceedings Ninth International Mining Geology Conference 2014 , pp 361–366 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By Lina Ospino Ballesta, Oscar J. Restrepo Baena, Juan Diaz Martínez

Artisanal and small-scale underground gold mining in Colombia plays a significant role in the country’s economy, but it faces persistent occupational hazards that threaten worker safety. Despite mining economic contributions, outdated technologies, limited risk management practices, and insufficient regulatory enforcement have led to recurring workplace accidents, many of which have been fatal. This study presents a systematic review of mining-related accidents over the last decade. Through geo-referenced analysis, high-risk municipalities were identified, and the frequency of accidents was correlated with the mining legal status and operational practices of these municipalities. The findings underscore the urgent need for evidencebased interventions that are tailored to the country’s unique mining context. Ultimately, this research contributes to the global discourse on mining safety by highlighting practical pathways to reduce occupational risks and promote safer, healthier workplaces in resource-constrained environments.

Feb 22, 2026

By Pablo Altoé Amorim, Bruno Sellitti Borges, Otávio Lube dos Santos, Arthur Pizetta David, Matheus Diogo Penido da Silva

Automation is in everywhere nowadays, including within companies and industries, and is therefore fundamental and essential for production, quality and process control of them. There are many ways to automate a production line or a machine can be through relay logic, Programmable Logic Controllers (PLCs), and even more modern microcontrollers with native Internet of Things (IoT) support can be used. What are the advantages and disadvantages of each approach? A PCB was created using more modern microcontrollers programmed in C, C ++ and Whiting language to simulate a replacement of a PLC in an actual machine. Having a very positive result, being able to handle the machine manually via Wi fi besides being able to also perform a real-time monitoring of the machine's motors through the mobile phone, thus entering the IoT and fitting into the Industry 4.0.

Oct 1, 2019

By C. J. Clayton, A. J. Haynes, D. A. Hickson, B. Thiele

The Meadowbank Gold Project, formerly owned by Cumberland Resources Ltd. and currently owned by Agnico Mines Ltd., is currently being developed approximately 70 km north of Baker Lake, Nunavut, in the eastern Canadian Arctic region. The Meadowbank Gold Project currently consists of a series of gold-bearing deposits within relatively close proximity to one another, which are planned to be mined primarily as a truck-and-shovel open pit operation using conventional gold milling and extraction. The mining plan indicates that approximately 20 million tonnes of ore will be mined over a mine life of eight to ten years. The operation will generate approximately 160 million tonnes of mine waste rock and about 20 million tonnes of tailings. The site is located in an area of continuous permafrost with mean annual average air temperature of -11°C and average annual precipitation in the range of 100 to 200 mm. Lakes cover a large portion of the site, including some of the ore deposits. The location of the site and the physical environment pose challenges to development. This paper presents some of the designs considered to effectively manage and utilize the waste products of mining at the project. Note that volumes, tonnages, construction concepts, and data presented in this paper are accurate for the time of writing and are subject to change and modification as the project progresses, additional modelling is carried out, and additional data are obtained.

Jan 1, 2007

By John J. Schanz

The ideal entering freshman for the College of Mineral Industries possesses the necessary aptitude to complete successfully a difficult technical curriculum, has a highly developed intellectual curiosity and adequate preparation in basic mathematics, sciences, and English, is enthusiastic about pursuing a career in the mineral industries, and puts forth a good academic effort while attending Penn State. The present programs of the University?s Division of Counseling and the College of Mineral Industries are directed toward providing the College with students who will meet these requirements. At present, freshmen are admitted to the Pennsylvania State University without entrance examination if they are in the upper two-fifths of their high school classes. All Pennsylvania students in the lower three-fifths are required to take the University Aptitude Test and all out-of-state students the College Entrance Board Examinations. Such students are admitted only if they score sufficiently high on either test to indicate the ability to do satisfactorily the work of University students. Only to this extent, are native intelligence and areas of greatest aptitude known for the Freshman prior to admission, and they are, therefore, largely beyond the control of either the Division of Counseling or the College of Mineral Industries. Because all freshmen, with exceptions that are numerically minor, are required to select a curriculum before admission to Penn State, each student who presents himself for required counseling during the summer, prior to his first semester, has already made a choice of his course of study. In many instances, such choices have been made without a rational and serious consideration of the student?s abilities and interests. Through tests given between the date of admission and the date of the counselling interview, it is possible to measure these characteristics and for the Division of Counselling to advise the student of his chances of success in his chosen curriculum. If he is qualified for the curriculum he has selected, Counselling Service goes on to direct the student?s attention to those other curriculums which are in the same general area as the one he has chosen and which will also challenge his abilities and correspond to his interests, Through this counselling, the curriculums of the College of Mineral Industries, which are often less well known to high school students than others for which they are no more qualified by ability or interest, are brought to the attention of the incoming freshman.

Jan 1, 1959