Search Documents

By D. Paktunc, S. P. du Preez, J. P. Beukes, P. G. van Zyl, A. Jordaan

"The chromium (Cr) content of stainless steel originates from recycled scrap and/or ferrochrome (FeCr), which is produced mainly by the carbothermic reduction of chromite ore. The oxidative sintered pellet production process is one of the most widely applied FeCr processes. The supplier of this technology specifies that recycling of chromite-containing dust collected from the pellet sintering off-gas and fines screened out from the sintered pellets (collectively referred to as pre-oxidized chromite fines) should be limited to a maximum of 4 wt% of the total pellet composition. However, the results presented in this paper suggest that recycling of such fines up to a limit of 32 wt% of the total pellet composition may improve the compressive and abrasion strengths of the cured pellet. In addition, electron microprobe and quantitative X-ray diffraction (XRD) analyses demonstrate that chromite grains present in the pre-oxidized chromite fines consist, at least partially, of crystalline phases/compounds that will improve the metallurgical efficiency and specific electricity consumption (i.e. MWh/ton FeCr produced) of the smelting process. Introduction Stainless steel is a vital modern-day alloy that is well-known for its corrosion resistance, which is mainly due to the inclusion of chromium (Cr) (ICDA, 2013). Stainless steel is mostly produced from recycled scrap and ferrochrome (FeCr), a relatively crude alloy of Cr and iron (Fe). FeCr is predominantly produced by the carbothermic reduction of chromite, a mineral belonging to the spinel group characterized by the unit formula [(Mg,Fe2+)(Al,Cr,Fe3+)2O4] (Haggerty, 1991; Paktunc and Cabri, 1995; Tathavakar, Antony, and Jha, 2005). Although Cr can occur in 82 different minerals, chromite is the only source of new Cr units that can be exploited in commercial volumes (Motzer and Engineers, 2004). Approximately 95% of mined chromite is used in the production of various FeCr grades, of which high-carbon and charge grade FeCr are the most common (ICDA, 2013)."

Feb 1, 2019

By Dong-dong Liu, Jian-ping Niu, Qi Liu, Shu-sen Cheng

A numerical model was developed to simulate the three-dimensional heat transfer in the belly and lower shaft region of the blast furnace wall consisting of copper steel composite stave, packing and shell. The temperature distribution of copper steel composite stave without the slag layer or refractory lining was investigated and then compared with the copper stave. The results showed that copper steel composite stave can satisfy the requirement of overheatingfree and had an analogous heat transfer behavior as copper stave but more stable cooling intensity. This model had been validated by the good agreement between the computed and measured temperature in the thermal test.

Jan 1, 2015

This paper puts the view that, for one gold deposit in Victoria at least, the Australasian Code for the Reporting of Identified Mineral Resources is severely deficient. The author questions whether or not the Code constrains the proper dissemination of information relevant to resource valuation. The author offers a view about the estimation of inferred resources, and provides data believed pertinent to the proper valuation of Ballarat Goldfields Ltd Ballarat East Project.

Jan 1, 1990

By E. Morrice

This report of the Federal Bureau of Mines presents a laboratory procedure, with the requisite equipment, for electrowinning ingot (liquid) cerium metal from a fused-fluoride bath, the metal purity being about 99.9 percent. Physicochemical studies, including bath properties and electrochemistry, are included, with a speculative model of the mechanisms involved. An historical review of the methods used for electrowinning misch metals and yttrim-group metals, as well as individual rare-earth metals, is presented. The electrolytic preparation of metal from fused salt and nonaqueous media is summarized, along with the unsuccessful attempts at depositing the metals from aqueous solutions.

Jan 1, 1961

By R. Castro, R. Gómez, F. Betancourt, M. Moncada

In block cave mining, rock fragmentation is a key parameter that influences the production level design and mine planning. Fragmentation occurs mainly by natural breakage during the caving process and in the draw column. The breakage that occurs within the column is known as secondary fragmentation. Secondary fragmentation has been successfully described using the block caving comminution model, which replicates the fragmentation mechanics between particles under drawn and vertical loads in a draw column. This model is based on a kinetic and population balance approach, in which non-normalized and normalized assumptions can be used depending on material and comminution system behaviour. In this paper, the non-normalized and normalized approaches are applied and compared to laboratory data to determine which assumption should be used for secondary breakage in block caving. Approaches are compared graphically, with the mean square error and the Fisher test with a false-rejection probability of 0.05. Based on a statistical analysis, the results show that the normalized model can be applied to all the rock types tested.

Nov 1, 2021

By Lance R. Barron

Over the past decade, the U.S. Bureau of Mines (USBM) has studied longwall gate road stability at four mines in the Book Cliffs and Wasatch Plateau Coalfields of Utah. These operations are characterized by multiple-seam mining, abruptly varying cover depths to 914 m (3;000 ft), and massive rigid, sandstone units in the main roof or floor. Such conditions encourage severe bumping, roof instability, and occasional floor heave problems.' Various gate road configurations have been employed to alleviate' these problems. Although the mines have comparable basic conditions, the lithologies and qualities of the immediate roof, floor; and seam ate different in each mine and often vary in a single mine. Gate road systems that mitigate hazards in one mine may prove inappropriate in another or for different areas of the same mine. This report relates the geology of the coalfields; describes the location, geologic setting, specific mining conditions, operating history, and the USBM field study and results or conclusions for each mine; summarizes the relative performance of the gate road systems; and emphasizes the need for site-specific geotechnical data to evaluate gate road conditions and performance.

Jan 1, 1994

By W. H. Hannay

Introduction The subject matter of this paper will be treated under two heads: (1) experimental work and the development of the purification system, and (2) the operation of the commercial plant. During 1927-28, a two-ton slag-retreating plant was in operation at the smelter for experimental purposes. Details of this operation and of the commercial plant are presented in a paper by G. E. Murray, read before the Annual General Meeting of the Institute in April, 1933 (1). A point which has considerable bearing on the subject of the present paper, and which was not emphasized by Mr. Murray, is the concentration of volatile impurities in the zinc oxide fume produced. The result of the operation of the slag fuming furnace is largely to confine in a closed circuit all the minor constituents of the Sullivan concentrates, both lead and zinc. They pass into the feed of the zinc fuming furnace, with the result that all impurities which volatilize-such as arsenic, antimony, tin, fluorine, etc.-report in the zinc oxide product. The accompanying condensed flow-sheet (Figure 1) will illustrate this. The only outlet for impurities which is not shown is the small tonnage which passes the Cottrell plants. The flow-sheet would indicate the possibility of building up a prohibitive concentration of cathodic impurities in the oxide leaching plant feed. However, after three years' continuous operation this has not occurred. Should this condition arise at some future date, discard of some tonnage of blast furnace slag is indicated. In Mr. Murray's paper, the much greater flexibility of blast furnace operation, due to the slag fuming furnace, is stressed, particularly as to the lead content of the slag. The requirements of our lead refinery call for a bullion containing about 0.70 percent antimony.

Jan 1, 1934

By Trent A. Tempel

In 1989 Newmont Gold company initiated a project to develop a treatment process for higher grade refractory gold ores to be mined from deposits along the Carlin Trend in Nevada. Extensive laboratory and pilot testing have identified a unique whole ore roasting process for oxidizing these ores prior to gold recovery by conventional cyanidation techniques. Subsequent detailed engineering studies by Fluor Daniel evaluated three different dry grinding flowsheets for feed preparation to this roasting circuit. The selected flowsheet will incorporate a two compartment ball mill with an attached drying chamber that is driven by a 11.2 MW (15,000 hp) wrap-around motor.

Jan 1, 1993

By Juel H. Stears

The bureau of Mines analyzed data from 47 coal mine roof-fall resupport accidents that occurred from 1966 through 1974 to identify critical hazards .and problems. These accidents resulted in 62 injuries or fatalities. It was concluded that the majority of the accidents might have been prevented by observance of recommended practices and use of available technology such as setting temporary supports, adequate roof testing, etc. Additional work is needed in the following problem areas where present technology is inadequate: (1) warning of impending roof falls shortly before they occur, (2) better methods of detecting unsafe roof and ribs, (3) providing access to and temporary support of high roofs for testing and bolting, (4) reducing the noise level of stopers, (7) developing temporary roof support; that have greater stability and can be remotely installed, and (6) reducing the number of roof falls through better permanent support.

Jan 1, 1976

By Gergely Markos

Uranium mill tailings represent a potential threat to the human habitat by containing large amounts of radioactive and chemically toxic substances in high concentrations. These: undesired components enter the human habitat in various pathways such as by erosion and water or air transport. The main objective of this investigation was to evaluate the actual movement and model the potential movement of contaminants by seepage of water from the tailings into the subtailings soil. This report represents various models of the movement of contaminants using both theoretical approaches and empirical evaluation of data available from other investigations. The data consist of field measurements and laboratory determi¬nations of major and trace cations, the dominant anions, pH, and Eh of moist solids, extracts, and waters from the tailings and surroundings. Evaluation and interpre¬tation of data were accomplished by using Eh-pH diagrams, various statistical methods and the WATEQFC computer program. Data analyses show that the critical area of investigating movement- is the interfaces between tailings and the external environment. The chemical differences at interfaces seem to result in a sink system for contaminants. The tailings-soil¬-water system shows extreme complexities because of chemical and physical hetero¬geneity of the system preventing the use of a single comprehensive model to represent real conditions. The validity of the simplifying assumption used has been shown and increasing complexity has been built into the models. Analogs of these models can be used for evaluation of similar systems.

Jan 1, 1981

By M. A. Hunter

IN the present state of public affairs, the reviewer turns from his traditional role of recording the progress made in research during the year and views the whole situation in which he finds himself in direct relation to the immediate needs of the nation. The slow progress of research year by year fades into comparative insignificance. The sum total of that research in all the years which have past becomes of importance only in direct relation to the extent to which we have translated or can immediately translate it into in¬dustrial production. For in a wartime economy immediacy is of paramount importance. The outcome of the war is being determined by our ability to pro¬duce and fabricate the metals and alloys which we require for its prosecution. Aside from iron and steel which lie outside the limits of this review, the most important of the nonferrous metals now needed in wartime production are aluminum, magnesium, nickel, chromium, and manganese. Some remarks on their production and fabrication follow.

Jan 1, 1942

By Larry M. Southwick, Phillip J. Mackey, A. E. (Bert) Wraith, Albert Pelletier

In 1881, the first commercial pneumatic Bessemer-type converter treating copper matte was successfully introduced by Pierre Manhes at the Eguilles copper plant near Vedène in France. This development followed over a year of testing on a smaller scale at a foundry in Vedène, during which the vertical tuyeres of the conventional Bessemer converter had been successfully replaced by horizontal tuyeres in an effort to avoid the freezing of copper which had occurred in the bottom of the vessel having vertical tuyeres. The Manhes Converter, as it became known, was the first successful large-scale adaptation of the Bessemer concept of using compressed air blown into a melt for metal refining and treatment. Within a few years, Manhes Converters utilizing horizontal tuyeres in either the original type of vertical converter, or a later and more enduring horizontal barrel converter, were in operation at over a dozen copper smelters around the world. It was this process that Messrs Peirce and Smith essentially improved with the introduction of the larger converter which bears their name and the development celebrated at this Symposium. The present paper briefly traces the original development by Pierre Manhes in the early 1880s and which set the stage for the later Peirce-Smith adaptation. The paper observes that the original development by Manhes was in part driven by the need to reduce coal (energy) consumption and hence the production cost in order for Eguilles to remain competitive with the larger plants in Swansea, Wales, where a ready supply of cheap coal helped keep smelter treatment terms of the day low. These themes are eerily resonant of today where booming copper production in China has impacted the industry, and also where energy consumption, closely linked to today’s more familiar theme of ‘climate change’ remains an important challenge currently confronting the entire industry. The paper concludes with comments on these seemingly parallel situations today and offers some thoughts for the future.

Jan 1, 2009

By Eric E. Cather

In 1981 the U.S. Bureau of Mines and U.S. Geological Survey conducted a mineral survey of the 5,100 acre (2,065 ha) Rubicon RARE II area (No. 5026) in the El Dorado National Forest (fig. 1). Work by the Bureau of Mines indicates that potential for mineral resources in the area is low. Samples from small gravel deposits along the Rubicon River and from favorable structures in the area contained smart amounts of economic minerals. A Tertiary river channel near the north area boundary contains gold values as much as $137.60 per cu yd ($180 per cu m) [(gold at $400 per troy oz ($12.86 per g)]. The channel does not cross the study area. Energy resource potential, including oil, gas, or geothermal, does not exist in this geologic environment.

Jan 1, 1982

By V. Panayotov, M. Panayotova

"Wastewater from ores processing is often polluted by molybdate and sulfate (SO42-) ions. Sorption is one of suitable methods for removing those pollutants when presenting in low concentrations. This work reports results on adsorption of sulfate and molybdate ions on metal modified (with barium - Ba and lead - Pb) and organic reagent modified (with Hexadecyl-trimethyl-ammonium bromide - HDTMA) clinoptilolite. Zeolite’s modification with Pb, Ba and HDTMA increases its uptake capacity with respect to Mo(VI) at pH 3, with the uptake capacity decreasing in the order CL-Pb > CL-HDTMA > CL-Ba. Lead-modified clinoptilolite shows high uptake with respect to Mo(VI) in acidic, neutral and slightly alkaline conditions. The presence of SO42- in concentrations twice higher than the amount of Mo(VI) do not interfere with the Mo(VI) removal by CL-Pb. Zeolite’s modification with Ba and Pb renders it able to immobilize SO42- from water in the pH range 3-9. Kinetics of the uptake process is best described by the pseudo-first order kinetic equation. Increasing the initial concentrations of Mo(VI) and SO42- increases the removed amount of pollutants. INTRODUCTION Wastewater from copper-molybdenum ores processing is often polluted by molybdate and sulfate ions. Molybdenum (Mo) migrates easily in water and consequently the Mo polluted areas could extend for hundreds and thousands of meters (Ryzhenko, 2010). Molybdate anion is the only Mo(VI) species in natural water, i.e. at pH > 6.0. Its median freshwater hazardous concentration affecting 5% of the species (HC 5.50%) is 38.2 mg Mo/L (De-Schamphelaere et al., 2010). The marine water chronic toxicity (HC 5.50%) is assessed at 5.74 mg Mo/L (Heijerick et al., 2012). The predicted no-effect concentrations (PNEC) are 12.7 mg Mo/L and 1.92 mg Mo/L correspondingly for freshwater and marine water (Heijerick et al., 2012a). When sulfates present in drinking water in excess of 250 mg/L they cause a cathartic action (especially in children) in the presence of sodium and magnesium, and when the concentration exceeds 600 mg/L, diarrhea. When sulfate-rich effluents are discharged into the environment, they may increase the acidity of water bodies and soils (Guimarães and Leão, 2014). Because of the adverse effects to human health and the environment, limits are set for SO42- concentrations in waters and wastewaters in the range of 250 / 500 mg/L."

Jan 1, 2018

By James R. Miller

This paper will describe the balling disc operation of the Marcona Mining Company at San Nicolas, Peru, with special reference to green ball quality. The report covers experience during the period of September and October 1965 and will be, more a state-of-the-art at Marcona report rather than -a technical treatise.

Jan 1, 1966

On 26 August 1971, the Bureau of Mines, through the Spokane Mining Research Center at Spokane, Washington, approved initiation of the evaluation of oscillatory energy toward enhancing flow of polymer into shale. The effort was an outgrowth of work performed under Bureau of Mines Contract H0210055, "Feasibility Study of Surface Impregnation equipment for the Chemical Stabilization of Coal Mine Structures," wherein feasibility of the impregnation concept was expressed and the detailed design of a machine for impregnation of coal mine roofs with polymer (under static pressure head) accomplished. Under these efforts, the potential enhance¬ment of polymer uptake into the shale thru superposition of oscillatory energy on the static impregnation pressure was suggested. A proposal for investigation of this phenomena entitled "Feasibility Study of the Application of Oscillatory Energy as an Aid to Afford Chemical Stabilization" was presented to the Bureau whereupon a three month program for initiation of investigation was approved.

Jan 1, 1972

By J Zhao, C E. Loo

The flame front is a narrow region in the iron ore sintering bed where coke particles combust. The maximum flame front temperature is as high as 1400°C. At high temperatures, the sinter mix components react to form melts, which facilitates material coalescence and the formation of dense sinter particles. It is well-established that flame front speed is an important factor influencing sinter productivity, sinter quality and fuel rate. In this work, the effect of suction, coke addition and mix moisture on flame front speed was studied in a pilot-scale sinter pot and also using the outputs of a recently developed theoretical model, which takes into account most of the significant physicochemical processes in sintering. Airflow through the bed has a large influence on flame front speed. A power law relationship between these two parameters means that increasing sintering airflow rate will lead to increased flame front speed, but the increases become smaller at higher airflow rates. Sinter pot test results showed that increasing coke addition decreased green bed permeability and increased flame front temperature, which resulted in increased flame front resistance and decreased flame front speed. Studies also showed that green bed properties are sensitive to sinter mix moisture level. The changes in green bed properties further influence the flame front speed and temperature.CITATION:Zhao, J and Loo, C E, 2015. Dependence of flame front speed on iron ore sintering conditions, in Proceedings Iron Ore 2015, pp 83–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Zhiqian Zhang, Chao Wu, Chao Li, Hongxu Li, Yu Chen, Xiangxin Hao

"In this paper, the life cycle assessment models for automobile lightweight materials including high-strength steel, aluminum alloy and magnesium alloy are developed by Gabi software. The evaluation models and evaluation indicators such as acidification effects, rich eutrophication effect, ozone layer depletion effects, global warming, resource consumption and formation of ozone potential were taken into account. It is shown that the effects of acidification and ozone formation are mainly derived from the run phase of high-strength steel and they have strong environmental impact load. While considering the entire life cycle with materials production phase and resource consumption, the aluminum and magnesium alloy appe art o have large r environmental load than high-strength steel. Base d on the evaluation, some optimization tips are proposed.IntroductionAs the increasing of car ownership, automobile has its two sides. One which is the convenient, efficient and fast traffic vehicle; the other is aggravating energy consumption, emissions and environmental pollution. The car industry faces heavy pressure with energy saving, safety and environmental protection. Nowadays, the main study ways for automotive energy-saving and environmental protection are power system improvement, alternative energy sources and technologies. For limitation of technique, development cycle and market share, the development of car is little progress at this stage and the application has been restricted. And another important way is the lightweight of vehicle. Usually there are three ways to get the lightweight automobile body structure, automobile body structure optimized design, using advanced body manufacturing technology, development and application of lightweight high strength body material.The life cycle assessment (LCA)[1lis commonly used to evaluate environmental factors and potential environmental impacts of products and services. As an environmental management tool of product-oriented, it becomes increasingly popular in industry. In this study, the concept of LCA and GaBi software was used to develop models for the three automotive lightweight materials, evaluate the environmental impact and make horizontal and vertical contrast by choosing variety of evaluation systems and indexes."

Jan 1, 2013

By R Domotor

Brisbane’s Airport Link is Australia’s largest road infrastructure project, worth a total value of A$4.8 billion. The project is using surface and underground blasting to excavate hard volcanic rock, Brisbane Tuff. This paper tells the story of the most challenging and difficult blast of the whole project: the removal of a remnant pillar of rock (approximately 2250 m3) next to a major arterial road and within 100 m of existing infrastructure including a number of heritage listed buildings, residences and privately owned sensitive receivers. The pillar consisted of a hard rock wall (Brisbane Tuff) between 2 m and 6 m thick, 15 m high and 35 m wide; with in situ precast concrete piles embedded within 1 m of the boundary of the pillar. Orica Australia Pty Limited was contracted by Thiess John Holland, to perform the work in this area, including design, modelling, drilling and loading of the explosives, as well as blast clearance and shotfiring. Access to the area was limited so all explosives and equipment, including the 20 t drill rig, had to be lifted in and out by crane. Due to the nature of the blast, with infrastructure 5 m directly in front of the 15 m high face, there was only ever going to be one chance to get this blast right. This was an extremely complex blast which required the use of a number of different types of packaged explosives, as well as special timing techniques only made possible by using electronic initiating systems. This type of blast is high risk, and is more typical of a building demolition in the urban environment. The blast was fired on the 25 September 2010, and was highly successful. The environmental results for vibration and overpressure were well under the imposed limits, and the embedded concrete piles remained undamaged.

Nov 8, 2011

By N. K. Singo, J. D. Kramers

The reprocessing of tailings resources to extract gold on an industrial scale has become common practice. While these projects are common in the Witwatersrand basin, similar low-technology processes are not operational in smaller goldfields. This study explores the possibility of reclaiming the tailings dump of the Louis Moore Mine in the Giyani Greenstone Belt, investigates potential hazards to communities in the vicinity, and identifies mitigation strategies. Auger samples were taken from the Louis Moore tailings at depths of up to 5 m. Aqua regia leach analyses show Au concentrations of up to 1 g/t. Inferred estimations based on ordinary kriging (OK) and inverse distance weighted (IDW) methods put the residual Au resource in the Louis Moore tailings dump at 0.20 t. Reworking the tailings is viable, although a potential environmental risk exists in the form of elevated arsenic concentrations. Further exploration is required to determine the mineralogical associations of Au and As. Tailings reworking would assist in raising funds for mine rehabilitation. The secondary tailings could potentially be repurposed, which would provide employment and facilitate community development, as well as deliver environmental benefits.

Jul 1, 2021