Search Documents

By Robert W. Burns

Gentlemen, my subject today is glass reinforced plastics. By definition, this encompasses a wide variety of materials: at least a half dozen basic varieties of polyester, epoxy, and phenolic; virtually infinite compounding variations within the basic groups: literally limitless variations in the amount and the nature of the glass reinforcing. Complicating all of this is the fact that different modes of application of the same material fall appreciably alter' the product's general strength and suitability. These many, many differing materials are what we conveniently call "glass reinforced plastics" or, more simply, fiberglass". This common name is actually a large part of the problem when dealing with fiberglass materials. Far too often a specification is written calling for simply "fiberglass reinforced polyester', based on successful prior use of a polyester laminate. Such a specification is very nearly worthless since such tremendous variation is possible under it. Success of a laminate furnished under such a specification is entirely dependent on good fortune

Jan 1, 1962

By Mario A. Terceros Herrera, Mario Terceros Arce, Antonio Marinucci

A Smart Cell is a closed-type tip post-grouting device that is attached to the bottom of the steel reinforcement cage of a drilled shaft and is used to enhance performance and to reduce uncertainty thereof. Control of the grout is maintained within the device during injection and a uniform stress is imparted across entire base area simultaneously, inducing a pre-mobilization load into the shaft as well as the soil. This paper describes the construction and tip post-grouting of drilled shafts from two bridge projects in the Santa Cruz, Bolivia region along the Paraí River. During the grouting process at each project site, there were noticeable differences in the grouting pressures achieved and responses observed, even within short distances between shafts. For this project, the greater benefit of using the Smart Cells was the reduction of risk and uncertainty of performance due to the highly variable soil conditions. Ultimately, since the response of each shaft was observed during grouting and because a “minimum” value of shaft resistance (i.e., pre-mobilization of load) was measured, there is a greater reliability with the anticipated performance of the shafts when axial loading is eventually applied.

By Roberto Parra

The classic criteria of the preparation of the charge for the smelting of copper concentrates in at flash furnace considers the mass and energy balance from the chemical and mineralogy composition of the concentrates. The operation parameters fixed with this method don't assure the stability of the operation and the critical problems of the slag quality and dust formation occurs very often. This paper presents the results of a laboratory test that allows the prediction of the behavior of concentrates blends in the view of the minimization of the dust formation and the magnetite control in the slag. The combustion of different copper concentrates and blends were done in a drop tube furnace The results show that the magnetite and dust formation don't have a linear behavior with the weight proportion of the blend and some optimal blends of 2 or 3 types of concentrates can be identified. From the reasonable hypothesis that the qualitative behavior of blends in the drop tube represents the real behavior in the burner, the preparation of the charge with this approach could help to solve those operational problems.

Jan 1, 2003

By Scott W. Hazen

METHODS of determining the grade and tonnage in a mineral deposit have not kept pace with scientific developments in certain other fields. The most commonly used methods of computing ore reserves and grade based on diamond-core-drill sampling are the cross section, the polygon, and the triangle. Tonnage and grade may be determined by these methods with acceptable accuracy, providing a sufficient number of samples is obtained; however, there is no means of determining when an adequate number has been taken or conversely if the deposit has been sampled excessively. It is demonstrated that, by using the techniques of statistical analysis, a mining engineer will be able to determine when a sufficient number of samples has been taken to determine the grade of a mineral deposit within a specified degree of confidence. Using statistical analysis to compute the estimated average grade of the ore makes it possible to compute a fiducial interval, when a distribution of the sample means is normally distributed, so that there is 95-percent confidence in the statement that the true average grade of the deposit is covered by the interval. This report utilizes data obtained from the Maggie Canyon manganese deposit, Artillery Mountains region, Mohave County, Ariz. Four separate exploration projects were conducted at Maggie Canyon between 1936 and 1950. Present economic conditions have made it desirable to determine the amount of 5-percent manganese ore developed by these projects.

Jan 1, 1957

By A. M. El Shafey, Ahmed W. Hussein, Ibrahim M. Gaafar, Mona M. Fawzy, Mohamed Diab, Mohamed S. Abu El Ghar

The Quaternary stream sediments of the Diit area, southern Red Sea coast, Egypt, were mineralogically studied for their content of economic heavy minerals. The study area covered approximately 450 km2 and included three main parts: Wadi and Delta Diit, as well as Diit lens. The mineralogical investigation revealed that these sediments contain considerable amounts of placer ilmenite, magnetite, zircon, sphene, apatite, garnet, and rutile. Also present, in minor or trace amounts, are uranothorite, monazite, xenotime, fergusonite, khatyrkite, and gold. The magnetic fractionation tests, supplemented with the XRD and SEM mineral analyses, indicated the presence of Fe-oxide minerals as wuestite, hematite, and maghemite accompanied with magnetite as products for hand magnet separation. Ilmenite separation was carried out using a high intensity magnetic separator at a current of 1 A, while the paramagnetic minerals (e.g., garnet, pyroxene, amphibole, epidote, monazite, xenotime, and fergusonite) were separated as magnetic fraction at a current of 3 A. The non-magnetic minerals (e.g., zircon, apatite and rutile, uranophane, uranothorite, gold, and khatyrkite) were obtained at 3 A current. On a mineralogical and geochemical basis, the present work suggests that Diit stream sediments should be considered as a potential source for Ti, Fe, Zr, Zn, and Cu after the physical upgrading processes for concentrating the minerals carrying the aforementioned economic elements.

Jan 21, 2022

By John R. Grillo, Gordian Ulrich, Franz-Werner Gerressen

Most geotechnical construction professionals are aware of piling using hydraulic drill rigs and the so-called Kelly drill mode. Kelly drilling has many advantages as it can work with a wide range of tools facing almost all types of soil and rock conditions. Kelly drilling can also deal with diameters up to 10 ft (3.00 m) and bigger or depths of more than 330 ft (100 m). Nonetheless, there is a concern about Kelly drilling as it is a relatively slow installation process. Therefore, an alternative piling method like Cased CFA (CCFA) Piles (Cased Auger Cast Piles) provides a significant advantage in terms of installation performance, schedule and cost saving potentials. Major application for the Cased CFA system is the secant pile wall construction. Against the traditional secant pile wall systems like fully cased bored piles or CFA secant piling the Cased CFA secant pile wall system has the advantage in cost and time against the fully cased system and in quality against the standard CFA system. This paper will describe the methodology and installation process in general as well as first reference projects carried out in the United States. This paper will present the results in cost and schedule saving using this method. In addition, we will also describe the limitations of this method. INTRODUCTION In the changing construction environment, companies are searching for new technologies or improvement of existing technologies to complete their projects in shorter time frames to provide a good economic solution. Especially with the focus of increasing urbanization, the aim of fast construction becomes more and more important. When thinking of piling, most people will have the same picture in mind: that of a hydraulic drill rig working in Kelly drilling mode; however, the perpetual drill rig development provides a number of options for the execution of specialist foundation projects, either for foundations or for pile walls when using single pass applications like CFA, Cased CFA and Full Displacement Piling (FDP). Single pass means, in general, that the tool is pushed and rotated into the ground to the final depth in one stroke. After reaching the final depth, concreting is started and concrete is pumped continuously while the tool is withdrawn.

Jan 1, 2019

By Aiyuan Ma, Tu Hu, Chenyu Sun, Yonggang Zuo, Hongying Xia, Jinhui Peng, Libo Zhang, Yongguang Luo

"In this study, the adsorption characteristics of tannin acid in aqueous solution were investigated using regenerated activated carbon (AC), with the aim to remove the tannin acid organic matter from the solution after zinc hydrometallurgy and Ge precipitation. Results showed the temperature has little effect on the adsorption ability (q.) of the regenerated activated carbon. The experimental equilibrium data were tested for the Langmuir and Freundlich isotherms. The adsorption equilibrium was better described by the Langmuir isotherm (R2 > 0.99). Pseudo first- and second-order kinetic models were used for describing kinetic data. It was determined that the kinetics of tannin acid removal was well fitted by second-order reaction.IntroductionGermanium recovery is a complex processes [1]. Hydrometallurgical processes are favoured and these are based on the precipitation of germanium as hydroxide or sulphide or alternately with tannic acid [2]. However, in the germanium recovery process, too much tannin is consumed by the germanium-tannins complexation process, and results in a high content of tannic acid remaining in solution, which is harmful to the valuable metal recovery [3]."

Jan 1, 2014

By K. R. Miller

Thunder Basin Coal Company has two mines located in the southern portion of the Powder River Basin. 60-90 km southeast of Gillette, Wyoming. The mines are principally located on federal coal leases acquired in the late-1960's. Development plans for the Black Thunder Mine focused on dragline stripping, but environmental considerations during the mid-1970's made truck-shovel stripping the method of choice when the mine opened in 1976. In 1981, the Coal Creek Mine opened as the first dragline mine in the Gillette area of the Powder River Basin. The regional terrain is flat-lying with occasional clinker-capped hills. The mines are located on the Wasatch and Fort Union Formation contact. The coals are Paleocene in age and the deposits are structurally simple, dipping gently to the west. The seams are thick and are classified as sub-bituminous-C. The Black Thunder Mine, with its 21 m thick seam, is strategically located in the center of the highest heat value mining area of the southern Powder River Basin.

Jan 1, 1993

By J Fisher, M Castro, A Hariyadi

The train haulage system being designed for PT Freeport Indonesia’s Grasberg Block Cave (GBC) will be located within the mine at an elevation of almost 3000 m above sea level on the west side of the island of Papua, Indonesia. The developing block cave is beneath the active Grasberg Open Pit and will transport 160 000 t of ore per day from multiple chute galleries to the underground crushing plants. The design entails 28 km of rail and 119 ore chutes, which will be brought online over the course of ten years.The train haulage system will be driverless and fully automated. Sequentially, the system includes remote controlled rock breakers at the top of the chute grizzlies, followed by remote controlled chute loading of the trains, then autonomous train haulage and autonomous unloading. An overhead catenary system (OCS) will power the locomotives, which are equipped with on-board batteries to drive through the loading and unloading sections. Service locomotives with drivers move material-laden freight cars in and out of the service shaft, destined for workshops, the magazine and batch plants. Service locomotives are also used for haulage level maintenance. Highly reliable and redundant control and communications systems are required to manage 12 trains in simultaneous operation.This paper provides an overview of the train haulage system’s technical complexities and the associated support systems interactions. The paper also highlights the project management issues and successes of this globally sourced project.CITATION:Hariyadi, A, Castro, M and Fisher, J, 2016. Automated train ore transport, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 563–570 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By A. C. Lordi

Present industrial plant design is influenced by motivators beyond the usual powerful one, creativity, on which Consultants thrive. The respected, although annoying, ever-present Return on Invested Capital becomes even more significant with anticipated escalation. Government regulations are having an increasing influence as air and water protection, sound and electrical safety requirements must be met And more recently, the increasing cost and uncertain availability of energy sources are having a revolutionary affect on plant design. More than ever before, the Consulting Engineer is faced with requirements and restrictions which tax even the most original thinkers -- and the result is good. This paper includes a brief review of recent trends in Cement Plant Engineering Design.

Jan 1, 1975

By C. R. Kuzell, G. H. Wigton

Knowledge of the thermal capacity of gases is of great importance in making metallurgical calculations. The metallurgist is frequeqtly called upon to investigate and determine furnace efficiencies in which the heat carried into or out of the furnace by gases is a large item in the heat balance. Not only do such problems present themselves in the determination of furnace efficiency, but also in the study of the application of heat in accessory apparatus, such as stoves, regenerators, waste-heat boilers, driers, etc. The thermal effect of the use of excess air in the combustion of fuel, the theoretical temperatures of combustion, the quantity of heat in hot blast at various temperatures, the effect of hot blast on furnace temperatures, are a few more examples of frequently occurring calorific problems involving gases. So many are the applications of the data on the heat capacity of gases that the subject merits careful study. The heat in a gas maybe due to its heat of combustion, if it is a combustible gas, and to its temperature. The latter is called its sensible heat and is the heat absorbed or evolved by a gas as its temperature is raised or lowered. The heat of combustion of gases is well established and is commonly known. The values can be found in almost any modern treatise on metallurgy. The sensible heat of gases has not been so well established because it is in most cases a function of the temperature, and the values of specific heats of gases over a wide range of temperatures have only recently been determined. It is the purpose of this paper to deal with the sensible heat of gases. - The calculation of sensible-heat capacities1 from specific-heat equations is a comparatively long and tedious operation. This is especially

Jan 1, 1915

By A Melloy, D Holt, M Jurak

Oaky North is AustraliaÆs highest producing underground coal mine. In 2011, the mine produced 8.7 Mt of high-quality coking coal. The high quantities are a result of the constant strive for optimising the operating time of major production units, which involves investing numerous resources, including diesel equipment, in supporting and maintaining their operation.In July 2011 it was identified that the diesel particulate matter (DPM) levels in the underground workings were above acceptable levels, due to the high level of diesel activity. Over the next 12 months, several controls were implemented to reduce exposure to personnel: the main ventilation system was upgraded; the production forecast was adjusted to better manage the diesel fleet, removing surges in diesel usage; and an electronic diesel tag board was introduced to centrally manage the distribution of diesel usage around the mine.From the start of the campaign in emission reduction, an intense DPM monitoring regime was established. Within a few months of the introduction of the centralised tag board, there was a major reduction in emission levels. After the installation and commissioning of the new main fans, the emission levels dropped further, such that over-exposures are now a rarity.Oaky North continues to explore new systems to better utilise their diesel fleet while still maintaining control over DPM emissions.CITATION:Melloy, A, Holt, D and Jurak, M, 2013. Reduction in diesel particulate matter at Oaky North, in Proceedings The Australian Mine Ventilation Conference , pp 187-190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By Donald J. Reining

The California Surface Mining and Reclamation Act (SMARA) is the nation's first legislation establishing a statewide mineral resource policy governing mining activities that recognizes regional needs and retains local autonomy. The Southern California Rock Products Association supported this proposed legislation. It was through our efforts that SMARA was passed in 1975. The local planning and zoning processes, which are so critical to the mining industry, have been significantly improved with implementation of SMARA. Recognition of the importance of the mining industry is now being developed by the State Mining and Geology Board and the California Division of Mines and Geology (CDMG).

Jan 1, 1984

By R. P. D. Graham

It is almost exactly two hundred years since the foundations of the mining and metallurgical industries in Canada were laid. There '."'as nothing spectacular about this early start. It had to do with the most basic phases of these industries-the mining of coal and iron ore, and the manufacture of cast and wrought iron. At several points along the coast of Cape Breton island, coal seams may be seen outcropping quite conspicuously, and it is probable that they had been observed, and possibly worked in a small way, in very early times. However that may be, these coal seams have the distinction of being the first in North America of which there is any printed record, reference to them appearing in a volume by Nicolas Denys which was published in Paris in 1672. Regular coal mining in the district did not commence until about fifty years later, however. The metallurgists started their operations along the north shore of the St. Lawrence river. Here, at many points between Montreal and Quebec, are to be found deposits of bog iron ore, and in 1 730 a furnace for smelting such ore was established on the St. Maurice river. The St. Maurice forges continued in operation until 1880, and throughout that long period they were famed for the fine quality of castings produced, and also for a-superior wrought iron.

Jan 1, 1924

This section presents highlights of world economic and mineral industry performance in 1982, a year characterized by continued recession, and selected 1983 forecasts of economic indicators of importance to the mineral industry, some of which indicate a modest improvement in the economies of the United States and Western Europe. The U.S. Economy in 1982 In 1982 U.S. gross national product (GNP) in current dollars increased at a rate of 4 percent, but GNP adjusted for inflation (real GNP) declined at a rate of 1.8 percent. Yearend 1982 real GNP was at roughly the same level as in 1980 (table 1). Thus no growth in real terms had taken place in the United States during the 1980-82 period.

Jan 1, 1983

By Stuart St. Clair

EARLY in 1936, when the American Petroleum Institute issued -J "American Petroleum Industry," which was a survey of the current position of the petroleum industry, and its future outlook, and the figures for petroleum requirements .for 1950 and 1960 were widely publicized by the several oil journals, the impression was given that the petroleum- industry must be nearing maturity and would by 1950 have passed the high' point of its obligations to business progress in the United States.`' Let -us look at the figures which might conduce, this thought. Referring to p. 32 of the report, the total indicated crude-oil requirements in 1940 are 1,099,000,000 bbl-; for 1950, the peak, 1,109,800,000 bbl.; for 1960 a decline to 1,071,020,000 bbl. This downward trend, then established, is probably expected to continue. And this in the face of a crude production in 1935 of 993,942,000 bbl., 38,858,000 bbl.

Jan 1, 1936

By K. Brady

Making progress on sustainable development will require greater attention to the management of materials produced from mine exploration through use to reuse, recovery and recycling. Material stewardship is a concept that embodies the range of activities required for optimal and appropriate use of minerals and metals in society. The following paper provides an overview of some recent initiatives that promote the stewardship of minerals and metals in society. The initiatives described are being conducted by organisations ? the International Zinc Association, the Canadian Copper & Brass Development Association and the International Council on Mining & Metals. These associations illustrate stewardship activities at three different levels: - an international association representing companies that produce a range of minerals and metals; - an international commodity association; and - a regional association. For each initiative, information is presented on its development, scope and outlook. This paper draws heavily from work of the associations but the viewpoints are the responsibility of the authors.

Jan 1, 2007

By Takashi Fujii

In the OG (Osaka Gas) process which includes a fusion process of sewage disposal sludge in coke bed knowledge of molten and fluid properties of the sludge are most important to controll the process in good condition. Thus, the softening and melting temperatures and viscosity were measured by the sessile drop technique and a rotating viscometer. Obtained results are summarized as follows: Melting character of sludge slag is varied according to their composition, but closely related to CaO/SiO2 ratio in ordinary sludge and to CaO/(Cr2O3,+Al2O3+P2O5) ratio in Cr2O3 containing sludge. Fluid property of sludge slag has a correlation with optical basicity or Riboud parameter, However, the correlation is poorer than that of metallurgical slags. Especially, chromium oxide containing sludge shows high viscosity and behaves somewhat different manner from ordinary sludge.

Jan 1, 1992

By Norma Golumbic

The primary purpose of the Bergius (hydrogenation of coal) and Fischer-Tropsch (hydrogenation of carbon monoxide) processes is the production of synthetic liquid fuels. This objective is of importance in insuring an adequate supply of motor fuels and lubricating oils in the United States. In the urgency of the basic research and process development work on synthetic liquid fuels, the possibilities for the production of synthetic chemicals inherent in these processes have hitherto received little attention in this country. However, the by-products, as well as the primary products, from the Bergius and Fischer-Tropsch processes are rich source materials for organic chemicals. The overhead oil from liquid-phase hydrogenation of coal, for example, contains benzene, toluene, xylene, cyclohexane, methylcyclohexane, aromatic solvents, about 20 percent tar acids (largely phenol, cresols, and xylenols), and 3 percent nitrogen bases. Wax, alcohols, and acids are by--products of the Fischer-Tropsch synthesis. In addition, techniques have been developed which make possible the production of aliphatic hydrocarbons, alcohols, acids, aldehydes, and other oxygenated organic compounds. These chemicals are more valuable on a unit basis than gasoline. Because of continued rapid expansion of the plastic, resin, lacquer, and solvent industries, larger amounts of many of these chemicals will be needed in the near future.

Jan 1, 1949

By V. H. Gottschalk

Sponge iron is a product resulting from the reduction of an iron oxide below the temperature at which the product melts. Commercial grades usually contain 80 to 95 percent metallic iron, 2 to 5 percent unreduced iron oxide, and an amount of siliceous gangue material depending on the pur.ity of the are used for reduction. The reducing agent may be gaseous or solid, and a large variety of procedures have been proposed for bringing the reducing agent into reaction with the iron oxide. Of the proposed procedures, the one that has the distinction of having been in continuous commercial operation for the longest time, from 1911 to date, was developed at a ceramic plant in Hoeganaes, Sweden, and yields? a product that has an enviable reputation as furnace feed wherever special, high-quality steels are made.

Jan 1, 1948