Search Documents

By H Haas

H. HAAS, San Francisco, Cal. (communication to the Secretary?). -Fig. 1 plainly shows that the comparison of the steam-turbine and Diesel-engine plants was made on a basis of 6,000 kw. continuous operating load. The tabulation of costs for an 8,000-kw. load is merely done to show the relation of increased output on' the unit power costs. Both plants would sacrifice their reserve capacity, which is to insure continuous operation, if operated to generate 8,000 kw. continuously; unless Mr. Hawkins advocates the operation of one of the turbines at 33.33 per cent. overload, retaining the other as a standby, which, besides overtaxing the turbine, results in a great loss of efficiency. It would he well for Mr. Hawkins to qualify certain of his statements. Thus, under the caption "Diesel Engines, Selection of Units," he says that "two of the largest Diesel-engine builders take the position that, in the present state of the art, they would not attempt to put out units over 1,000 kw.;" he should qualify it by saving that "two of the largest American Diesel-engine builders take the position that, in the present state of the art in the United States, they would not attempt to put out units over 1,000 kw." The reason that American manufacturers restrict themselves at present to units of that size is to be found not so much in a lack of experience in building large units as in a lack of a sufficient, demand for them in the United States to justify the heavy capital outlay connected with the development of such engines. There are relatively few localities in the United States where fuel prices are as high as they are in the Southwest, and regions of high fuel prices are sparsely settled and have a very limited demand for power. Where low fuel prices obtain, steam turbines are active competitors of Diesel engines for large power plants, particularly when the station load factor is low. As most of the American manufacturers of Diesel engines work under license agreements with European manufacturers, which limit their market to the United States and its possessions and Canada, a further limitation is imposed upon them, leaving to European firms practically the entire world as a market.

Jan 5, 1917

By Ralph H. Nafziger

The Bureau of Mines, in cooperation with the Idaho National Engineering Laboratory, has electroslag melted a V-5Ti-5Cr alloy using a fused CaF2, flux. The alloy is a candidate for use in future fusion reactors. One objective of this research was to evaluate the feasibility of the electroslag melting process in separating simulated radioactive isotopes from the V alloy to demonstrate recyclability. Small amounts of Ca, Y, and Mn were added as surrogates for radioactive isotopes. Results showed that this vanadium alloy can be electroslag melted satisfactorily. The impurities added intentionally were removed or decreased successfully. Among the major alloying constituents, Cr was retained but there were some Ti losses. The latter may be controlled with process refinements. This research suggests that the electroslag melting process could be a suitable method for recycling V alloys after use in future fusion reactors, or for processing other reactive metal alloys with more immediate applications.

Jan 1, 1996

Knowledge of the crystal chemistry of carbonate apatites is very important for the development of the concept of biomineralisation and the creation of a scientific base for new biocompatible materials for medical purposes. The present work is devoted to research results on various synthetic and biological carbonate apatites obtained at Saint Petersburg University over many years. All-important problems will be considered such as the location of CO32- ions in the apatite structure, the ionic substitutions in various biological apatites and the development of synthesis methods for their analogues. Syntheses of apatites were realised by precipitation methods and under hydrothermal conditions (from solid compounds and by calcite treatment). Biological samples used in this study were physiogenic and pathogenic apatites formed in the human organism, eg in teeth and in renal and salivary stones and dental calculi as well as apatites from fossils of different taxonomic families (brachiopods, conodonts, fishes, reptiles, mammal) with different geological ages and burial conditions. The study of the crystal chemistry of carbonate apatites has been carried out by powder (including high-temperature measurements) and single-crystal X-ray diffraction methods, IR-spectroscopy, thermal analysis and various chemical analytical techniques.

Jan 1, 2008

By K. Robinson

Following the longest Smelter campaign in BCL?s history it was planned to completely rebuild the flash smelting furnace in 1987. This was the fourth major overhaul and the most extensive so far attempted. Detailed planning took place over several year$ preceding the shutdown and implementation was completed in 54 days. The key to minimising shutdown time was the method designed for installation of the new uptake shaft and reaction shaft. Major repair work was also undertaken in the waste heat boiler and electric furnaces. Both of these activities had an impact on the critical path of the flash smelting furnace overhaul.

Jan 1, 1993

By J. N. Van der Merwe, M. Mathey

"The development and mechanical characterization of coal-crete, a composite material generated from coal fragments and some binder material, is described in this paper. Coal debris was obtained from a colliery in South Africa. The binder used in the study basically consists of cement and water, and further ingredients are added to the mixtures, such as sand, fly ash and polymers, in order to investigate alterations of the mechanical properties of coal-crete.Results from over 220 mechanical tests on coal-cretes with various binder mixtures give consistent trends for the material’s behaviour. Linear relationships are suggested between the uniaxial compressive strength, Young’s Modulus and the indirect tensile strength of the coal-crete.It is shown that mechanical properties comparable to coal can be achieved. Coal-crete is therefore suitable for physical modelling of mining situations in experimental studies and for use as backfill in underground coal mines. The latter application is particularly attractive when refuse coal is used as aggregate material. The indicated trends in this study may be used as a guideline for individual coal-crete design needs. However, some uncertainty remains as to the influence of particle shape, size and gradation, coal rank and age of the coal-crete. These aspects are recommended for further research."

Jan 1, 2015

By K G. Harding, E L. Haggard, C M. Sheridan

Mining is a water intensive sector, contributing to declining water resource quality around the world. Improvements to current mine water management practices can help reduce the amount of water utilised by the mining sector and the impact on water resources. Creating a water account can help companies understand water use in their operations and identify areas where water reduction is possible. Water accounting methods include the Water Footprint Network method and the WaterMiner tool.The Water Footprint Network method is used to determine the amount of direct and indirect water used by an organisation either in a process or to manufacture a product. The total water footprint is divided into the blue, green and grey water footprints. Blue water is the amount of water abstracted from surface and ground water resources. Green water is the amount of rain water utilised. Grey water is the amount of freshwater required to assimilate the waste stream to the natural resource and still conform to ambient water quality standards.The WaterMiner tool is a program available via the internet, which can be used to model water use of mineral processing sites. The program reports the amount of raw, worked and treated water used by the process and recommends flows that can be added to reduce the amount of fresh water required by the process.To gain information on mine water management practices in South Africa, a water account for a platinum mine was developed using the Water Footprint Network method and WaterMiner tool. Based on the results, suggestions to reduce the amount of fresh water utilised are made.CITATION:Haggard, E L, Sheridan, C M and Harding, K G, 2013. Water footprint for a South African platinum mine, in Proceedings Water in Mining 2013 , pp 15-20 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By Lucas Ladeira Lau

A legislação ambiental vem se tornando mais restritiva em diversos setores industriais. Isto não tem sido diferente para o setor siderúrgico. Com a inclusão de limites de emissão de elementos traços nas legislações ambientais mundo afora, este tema vem ganhando importância. É conhecido que a qualidade das matérias-primas utilizadas nos processos siderúrgicos pode interferir nos impactos ambientais de seus processos. No caso do processo de sinterização, a presença de elementos traços está ligada a composição de sua carga. Com o objetivo de determinar quais elementos irão compor as emissões atmosféricas, resíduos, efluentes e produtos faz necessário estudar o modo de ocorrência dos elementos traços em cada insumo. A interação entre as propriedades de cada elemento e as condições de massa e termodinâmicas permitem o estudo de seu comportamento e partição. Assim, o objetivo deste trabalho é levantar o estado da arte da sinterização de minério de ferro e suas emissões, estudando a origem, o comportamento e a partição de elementos traços e radionuclídeos, quando submetidos às condições do referido processo.

Aug 1, 2018

By Harold P. Rue

The problem of removing hydrogen sulphide from natural gas has become within the last few years one of major importance to the natural gas and petroleum industry. Several gas fields in the United States produce natural gas containing hydrogen sulphide, and a number of oil fields produce gas which contains hydrogen sulphide. 3 The percentage of hydrogen sulphide in natural gas produced in these fields varies from a fraction of 1 per cent to as high as 20.5 per cent by volume. Hydrogen sulphide is probably the most toxic gas associated with natural gas, and from the standpoint of health and safety it is important that the hydrogen sulphide be removed if the gas is to be used for domestic purposes. Hydrogen sulphide, besides being toxic and therefore a hazard to animal life, is under certain conditions an active corrosive agent and very destructive to equipment. The annual loss caused by the corrosive action of hydrogen sulphide on equipment amounts to hundreds of thousands, perhaps millions, of dollars. The largest percentage of natural gas produced in the United States comes from wells which also produce oil. This associated gas invariably carries with it light fractions of petroleum, which when separated from the gas, condense to the liquid form at ordinary temperatures and pressure. Commercial application is made of this natural condition, and "wet gas" is processed to obtain so-called natural gasoline by employing the principles of absorption, adsorption, or compression and subsequent expansion accompanied by cooling. In the manufacture of natural gasoline from wet gas which contains hydrogen sulphj.de, if this contaminating gas is not first removed, some of the hydrogen sulphide may oxidize to form free sulphur and water. The free sulphur will dissolve in the gasoline produced by any of the aforementioned methods and cause the product to be positive to the corrosion test and there-fore unsuitable for commercial use in that condition. The objectionable sulphur compounds can be removed by washing the gasoline with a solution of caustic soda or other chemicals, but this treatment is expensive. It is advantageous therefore to remove the hydrogen sulphide from the gas before it is processed in a natural-gasoline plant.

Jan 1, 1932

Cretaceous volcanic activity (Hauterivian Albian) in the Peruvian Andes can be found along the coast of Peru and the western edge of the Andes mountains between 15o30'S and 5o30'S, extending discontinuously in south to Chile and north to Ecuador and Colombia. This volcanic activity formed in three aborted marginal basins; the NNW-trending volcanic Ca±ete and Huarmey, and NNE-trending Lancones basins. These volcanic rocks are predominantly andesitic and basaltic in composition, of calc-alkaline and tholeiite affinity with subordinate dacitic and rhyolitic rocks. One notable feature is the appearance of æocoitasÆ from Ica (14oS) south to Santiago de Chile. These rocks have a calc-alkaline to alkaline affinity. From south to north, the continental crust gradually becomes thinner, allowing mantle material to rise towards the surface. Ophiolitic sequences of this type form a marginal basin in Colombia. Very low-grade regional metamorphism which affects the volcanic rocks also varies gradually from south to north. Between Santiago de Chile and Ica this takes the form of burial metamorphism, with moderate geothermal gradients (20o-30oC/km). Metamorphism in the Huarmey basin is transitional between burial and ocean-floor metamorphism, with very high geothermal gradients (>3000C/km). High geothermal gradients are also apparent in metamorphism of the Lancones basin, though less than the other basins. Ocean-floor metamorphism is present in the ophiolitic sequence in Colombia. Associated mineral deposits in the Huarmey and Lancones basins, and in the north, are of the volcanic massive sulphide-type (VMS). The principal deposits in Peru are Leonila Graciela (20 Mt Zn and Pb) and Tambogrande (40 Mt Cu and Zn). There are also smaller mines and prospects. To the south of Lima, manto-type Cu deposits (CuMT) are found with a mineralogy of chalcopyrites, pyrites, magnetite, actinolite and apatite. The main example is Raul Condestable (10 Mt Cu). Other prospects are present to the south and Chile has some very large mines of this type (El Soldado, Lo Aguirre). The notable differences between the CuMT and the VSM deposits are thought to be the result of the prevailing conditions in the earthÆs crust during the Hauterivian Albian. To the south, calc-alkaline and alkaline volcanic activity in aborted marginal basins, with thicker crust, was thick, produced moderate geothermal gradients associated with burial-type regional metamorphism and deposits of CuMT. In the north aborted marginal basins associated with calc-alkaline to tholeiitic volcanic activity and a gradually thinning crust, produced transitional regional metamorphism between burial-type and ocean-floor type, associated with high to very high geothermal gradients and VMS deposits. In Colombia these conditions led to ophiolite extrusive rocks, ocean-floor metamorphism and also VMS deposits.

Jan 1, 1999

By B. M. Eiter

The impact of fatigue is seen not only in its effect on the job performance of haul truck operators but also on the health of the operator and the productivity at the mine site. Its impact can even extend outside of the mine site to the health and well-being of the surrounding community (Fourie et al., 2010). In this paper, a case study of a small, surface mining organization is presented. The goal is to highlight the fatigue risk management system implemented at the studied mine site. Mine safety personnel who were interviewed discuss the changes made to the infrastructure of the mine, to administrative areas such as the number of shifts and the use of vacation time, as well as the implementation of new technology into haulage vehicles. This paper reviews how these changes are supported in the research literature.

By David C. Slack

In recent years public concern over the environment has grown enormously. A very aware populace has exerted pressure on its legislators to enact enforcement laws dealing with pollution. Among the different types of pollution, sulfur dioxide in the air is a large and readily identifiable constituent. Air pollution, according to the EPA, costs the U, S. billions annually with SO2 a major portion of this cost. Fossil fuel and oil fired power plants release better than 50% of the SO2 in the country. Thus great attention is being focused on the methods power plants are utilizing to control emissions. With a time schedule of compliance by early 1975, decisions are being made and systems chosen that will have to perform - and perform - and perform. Therefore, a large majority of the power plants are presently considering lime in the planning and operational phases of their stack gas desulfurization programs. The reasons for this are: Lime scrubbing has more development and pilot work completed than most other methods; the removal potentials are relatively high; the stoichiometric ratios are not excessive and, the process has relatively low capital and operating costs. Many pilot plant studies have been completed recently using lime and the first operational full scale lime scrubbing unit is now in the start-up phase at this time at Duquesne Light Company's Phillips Station here in Pittsburgh. Also, because of completed development work, the problem of solid waste disposal will also be tackled at this power station at the same time. There are various methods for the use of lime in scrubbing for S02, but for our purposes I would like to describe the cyclic wet lime process. This method called "Scrubber Addition of Lime" involves contacting the flue gas with a slurry of milk of lime.

Jan 1, 1973

By Pratima Meshram Abhilash

In this review, availability of germanium in primary and secondary resources and its recovery from these resources are presented. With nearly 40% germanium consumed in fiber optics and scarcity of resources, the global consumption outplays the primary production. Germanium exists as a substituted element in zinc sulfide matrix of lead–zinc sulfides and lignites. Nearly 60% of the germanium supply is met by zinc refining residues, and about 20–30% of germanium is produced from coal and its by-products. Germanium recovery from various resources such as zinc plant residues, coal and coal plant waste, spent optical fibers, and copper flue dust has been examined. Bioleaching was exploited by few researchers to extract germanium from zinc sulfides, sulfide tailings, jarosite, coal fly ash, and flue dust. This review covers the various work carried out by different chemical separation processes, viz., chemical precipitation, solvent extraction (SX), ion exchange (IX), and membrane processes, as well as biological approaches.

Jan 16, 2022

By Ayşe Ece Yıldızçelik, Mehmet Buğdaycı, Onuralp Yücel

ZrB2 and TiB2 are significant metal borides. They are being used in various industrial areas from space technology to nuclear industry owing to their physical properties such as high melting point, high thermal/electrical conductivity and low density. Present study was conducted in two main stages: self-propagating high-temperature synthesis (SHS) reactions and leaching. ZrO2, TiO2, B2O3 were used as starting material and Mg was used as a reductant to produce ZrB2-TiB2 powders via SHS. Therefore, it was aimed to determine production parameters, leaching conditions and comprehensive examination of final product features. The samples were characterized by using chemical analysis (AAS), XRD, XRF and SEM/EDS techniques.

Jan 1, 2015

By D. D. Eyer

New or improved technology will continue to drive productivity improvements through the next decade. In January 1988, I presented a paper titled, "Large Underground Mines of the 1990s? before the SME. I will follow some of the themes developed in that paper as modified by our experience in the past two years. In order for a coal company to be profitable today, it has had to reduce unit costs experienced in the past. This is because the current average realization, even accounting for a recent strengthening, remains below that of a few years ago. Doing business as was done in the past is not good enough. The coal industry needs to increase productivity in the range of 5-10% annually merely to stay even with rising costs. Underground productivity has been increasing more rapidly than that for surface mining. With the exception of the Powder River basin of Montana and Wyoming, underground productivity has caught up with that for surface mining in many regions of America. There are a number of technological factors which have attributed to increases in underground productivity and which should be factors in the future.

Jan 1, 1990

By Thomas E. Shufflebarger

Glass is one of man's most versatile creations. ---The earliest glaze known---is about 12,000 B.C. ---The oldest pure glass is a moulded amulet of about 7,000 B.C.---. Indicative of a knowledge of properly-proportioned, quality raw-material, means were found for producing the first relatively clear, transparent glass at about the beginning of the Christian era. The fundamentals of almost all the modern, technical processes of manufacture were established during the 3rd Century. (1) Glassmaking, practiced in Colonial America, was moved toward the Ohio Valley in response to increasing demands for fuel. This move, beginning in the 1860's resulted in the use of the glass sands contained in the Oriskany (and St. Peter) sandstone. (2) Glass sand,(3) virtually pure, fine-to-medium-grained quartz sand(4) is the principal raw material used in the manufacture of glass; it constitutes proportions which range to a maximum of about 72% and seldom is glass made without it. However, acceptable glass sands are, invariably, those which most nearly fit the glass-producer's economic needs and any method used to evaluate a raw material's potential must finally prove equatable with such needs. As used in the United States, source-rocks of glass sand include sandstone, unconsolidated silica sands, quartzites and vein-quartz. Admixtures of silica sand and other (principally clay and feldspar), readily separable components have been proven viable. However, the silica sand, refined by nature to a high degree of purity, is the desirable product of exploration. If the term, standard, is justified by long-continued use, the Oriskany - and St. Peter sandstones are, together, the nonesuch of the glass sand industry they provide the principal tonnage of melting sand. According to Grimsley,(5) Ottawa, Illinois, glass-sand is considered the standard glass-sand of the West and the analyses of Berkeley Springs sand (Oriskany) compare most favorably with this sand.

Jan 1, 1974

Many mining operations are uncertain of what costs they should be achieving. The majority of cost estimates are based on historical costs that have added contingency factors. Historical costs are a valuable source of information but a more precise costing method is necessary. There are several alternative methods for predicting costs. A methodology which provides the best indication of the achievable costs is one using a standard inventory list and a bill of quantities. The model is termed a Basic Principles model and addresses basic design principles and engineering constraints.

Jan 1, 1990

By P. N. Calder, D. B. Apel, S. D. Butt

Mine-wide (MW) microseismic systems use widely spaced transducers to determine the source location and parameters of stronger microseismic events, while high frequency (HF) systems use fewer transducers to monitor local areas for the weaker events that can precede stronger events. Previous monitoring at the Creighton Mine indicated that an HF transducer located 120 m away from an active stope recorded two types of activity in response to production blasting: the first occurring at the same time as the production blasts and associated with the passage of the direct seismic waves from the blast through the local area, and the second occurring several hours later and associated with the arrival of a slower moving stress change through the rock mass (which was identified by the mine’s MW system). Interpretations of locally increased stress levels, based on analysis of the recorded HF events, correlated with the nearby occurrence of two strong seismic events. These results were applied to a similar monitoring trail at the Kidd Creek Mine where the transient stress changes induced by several development blasts were monitored. It was observed that increases in HF activity corresponded with the occurrence of MW events near the transducer location, and that fewer HF events were recorded the longer this occurred after the blast. Local geological features appeared to influence the number and occurrence of both HF and MW events.

Jan 1, 2000

By Marcela Aliaga

Este trabajo propone una metodología para disponibilizar un mapa de calor de riesgos de conflictos sociales, que sirva como instrumento de alerta temprana y de gestión preventiva, pero que también permita comprender cuáles son los factores concomitantes que inciden en la mayor probabilidad de ocurrencia de conflictos sociales vinculados tanto con las prácticas empresariales como con las condiciones socioeconómicas y culturales del contexto. Para elaborar este mapa de calor, se ha construido un índice de riesgo de conflicto social que incorpora 13 variables (7 internas o vinculadas con el desempeño de la empresa y 6 externas o de contexto).

Sep 29, 2023

[ ]

Jan 1, 1938

By Ben Hogg

Since the development of the top-submerged lance (TSL) technology for copper and lead smelting by the cooperation of Mount Isa Mines (MIM), now owned by Glencore, and the Commonwealth Scientific Industrial Research Organisation (CSIRO) the core of the ISASMELT™technology has always resided in the lance system. Through continuous innovation and operation of our own smelters, first at MIM, subsequently at Mopani, and also at both the Kazzinc Copper and Kazzinc Lead smelters, Glencore Technology have expanded the core equipment supply to enhance the plant operability. The success of Glencore Technology’s expertise can be directly measured by the success of the Kansanshi Copper Smelter plant, which achieved 100% nameplate capacity within three months of start-up. This paper describes the ISASMELT™ core equipment and how it is applied to smelt sulfide materials. It highlights the strength of the ISASMELT™: continuous innovation to facilitate the versatility and continued increased capacity with every plant implementation.