Search Documents

By John L. Sundstrom

Complete systems were designed -and are in operation to recycle the effluent streams and to remove impurities from tankhouse. electrolyte, Heavy em¬phasis was placed on making usable products from as many streams as poss¬ible at minimum capital and operating costs. Almost complete recycling: and reuse of water and sulfuric acid were paramount. Techniques used in-clude solvent extraction - electrowinning, evaporation - crystallization and filtration.

Jan 1, 1992

By H. M. Ray

The discovery of the New Lead Belt in the mid-'50s began a search for mill design criteria that is continuously updated. The opportunity to design, construct, and operate four new mills in the span of 20 years provided fertile areas for new concepts. The central theme for design parameters encompassed simplicity, functional, and economic consideration. Ore characteristics for each plant remained relatively constant, providing stable criteria for grinding circuits. Bond index nominally 10-12. Flotation circuit parameters were based upon power application with 10-20% excess capacity built-in to protect recovery. Newer equipment exhibits greater power application efficiency lowering horsepower requirements per ton. Instrumentation was installed to stabilize circuits, protect equipment, and improve products. With ever increasing requirements of higher quality products, environmental considerations, and operating cost pressures, the upgrading of operating procedures is in a constant state of flux. Installation of more efficient equipment, chemical processing, or any other technique would be considered as feasible. Current practice is for St. Joe to design and engineer in-house its own plant design. The exception being detailing of structural steel. It is felt that familiarity with past design criteria serves as a valuable foundation to incorporate changes. Also, direct contact with operator provides specific data, and feedback for constructive criticism that is utilized for defining and correcting problems. The results are in reality an operator's plant with the benefit of advancing technology that meets the demands for improved products without sacrificing the economies of throughput or recovery.

Jan 1, 1977

By Joel N. Van Sant

The rapidly expanding economy of the West, with its growth of heavy industry, and increased steel production, is primarily responsible for the refractory clay industry's concern over the adequacy of the clay supply in States of the Great Plains and Rocky Mountains. Hence, the investigation by the Federal Bureau of Mines of the occurrence and use of refractory clays in North Dakota, South Dakota, Nebraska, Wyoming, Colorado, Utah, New Mexico, and Arizona has been encouraged by the major consumers and producers of this commodity. The Wyoming investigation is a part of the national program devised to close gaps in the domestic supply of specific types of clays to determine their characteristics and properties and to provide information that will assist the refractory-clay industry. Forty-two locations of clay-bearing rock in 17 areas in Wyoming were examined (fig. 1). Location 3 was not examined during this survey. Its description was taken from an earlier report. Locations 20, 21, and 22 were previously reported but were, also, examined by the Bureau. No samples were collected from these locations because field examination indicated that the shales were not refractory grade. The Hulett, Aladdin, and Newcastle areas are discussed in the section on the Black Hills district; the other 14 areas are described separately.

Jan 1, 1961

By E. S. Peters, M. J. van Rensburg, M. Le Roux, Q. P. Campbell

"The demand for energy has continued to rise worldwide in line with population growth. The majority of South Africa’s electricity is supplied by coal-fired power stations. The amount of fine coal (-2 mm) generated at coal processing plants has increased, due mainly to mechanized mining methods. Fine coal retains more water, which lowers its heating value.Drying the coal is costly and it is difficult to achieve the required moisture content. Consequently, coal fines are often discarded. An estimated 8% of the total energy value of mined coal is lost1.Fluidized bed technology is often used to dry coal thermally, but this method is expensive and has an adverse environmental impact. The objective of this study was to investigate the removal of moisture from fine coal (<2 mm) in a fluidized bed operated with dry fluidizing air at moderate temperatures as the drying agent. The effects of different air temperatures and relative humidity levels were investigated in a controlled environment. The study further investigated the influence of coal particle size on moisture removal.The drying rate was found to increase with increasing temperature. The relative humidity of the drying air had a more pronounced effect on the drying rate, even at temperatures as low as 25°C.. It became more challenging to remove moisture as the particle size decreased. The gain in calorific value was greater than the energy required to dry the coal samples, showing that a fluidized bed using moderately warm dry air is an energy-efficient drying technology. The energy efficiency of the fluidized bed compared favourably with other thermal drying methods.Paper written on project work carried out in partial fulfilment of Degree in Chemical Engineering(NWU) - Pursuing Masters in Coal Beneficiation"

Jan 1, 2015

By Earl T. Hayes

[This work represents a continuation of the efforts of the Metallurgical Division of the Bureau of Mines to ascertain and apply knowledge of mineral physics to process metallurgy.]

Jan 1, 1941

By Gunnar Eriksson

Computer simulation has become an everyday practice in thennodynamic and materials research. Advanced thennochemical algorithms take into account heat transfer effects and salient reaction kinetics when applied for process models. In particular, the combination of mass transfer or overall reaction rates with multi-component Gibbs energy minimisation provides an effective tool for simulation of industrial thennochemical processes and processing of materials. In this work the combination of rate factors with the Gibbs energy technique was studied by using the novel program ChemSheet, which operates through Microsoft&apos;s Excel® spreadsheets. Such processes as, for example, CVD of pure silicon production, titania pigment manufacturing, vapour pressure of Mercury in amalgams (in Hg-Iamp manufacturing) and melting behaviour of low-temperature alloys have been modelled. Provided that the thennochemical data is available simulations can be performed with any thennodynamic system. The calculation can be performed as an affinity study without a particular reactor model or with a specific reactor scheme.

Jan 1, 2001

By Diego Ruben Martin

Este trabalho objetivou comparar, por meio de experimentos desenvolvidos em uma fundição, através da adição de três inoculantes diferentes (IM-22 com FeSi-Ba/Zr, G 20 com FeSi-Ba) e IMSR 75 com FeSi-Sr), para observar as características da vida util de ferramentas na usinabilidade das peças, microestrutura e propriedade mecânica. A metodologia da pesquisa se baseou em analisar principalmente pelo processo de fresamento o ferro fundido cinzento GG-25 inoculado diferentemente, denominado de acordo com a Norma DIN EN 1561. As formas de avaliação dos resultados terão como base uma análise quanto ao desgaste da ferramenta, acabamento superficial, análise microestrutural, composição química e propriedades mecânicas do material da peça. Os resultados mostraram que dentre os inoculantes aplicados o com Sulfeto de Estrôncio (SrS) apresentou-se mais estável termodinamicamente que as amostras inoculadas com os outros dois inoculantes, pois ele levou a uma variação da energia livre de Gibbs mais negativa e portanto mais favorável a formação de núcleos com raio crítico (rc) maiores, o que permitirá uma solidificação com nucleação heterogênea. Todavia o respectivo inoculante também foi mais eficiente na formação de uma microestrutura mais estável, com maiores quantidades de células eutéticas e vida útil do inserto mais longa quando usinado.

Aug 16, 2017

By M. Moats, I. E. Paschalidou, K. Awuah-Offei

Tellurium (Te) is a rare metalloid that is predominantly produced from the treatment of anode slimes formed during copper (Cu) electrolytic refining. The US Government lists Te as one of the 50 critical minerals, partly, because of its use in thin-film photovoltaic (PV) technology. Given policy initiatives to increase Te production, it is important to evaluate the life-cycle environmental impacts of Te recovery as a by-product of Cu processing. The literature contains a few specific life cycle assessment (LCA) studies of groups of metals that include Te without proper regard to impacts per life-cycle stage of Te production or the effect of allocation on the results. This study builds an LCA model of the production system of Te from anode slimes treatment to evaluate the effect of allocation on life-cycle impacts. We build life cycle inventories using data from the Ecoinvent v3.7.1 database, literature, and engineering calculations and allocate impacts in proportion to products’ mass and economic value. The results show that economic value-based allocation yields greater impacts than mass-based allocation indicating the significant effect of the allocation approach on life-cycle impact estimates.

Feb 1, 2023

By L. C. IlsLey

One of the details which the engineers observe closely in conducting tests on explosion-proof type equipment at the Pittsburgh experiment Station of the Bureau of Mines is the construction of covers and their means of fastening. These covers are of particular concern from a safety standpoint, because they are very liable to be frequently disturbed for the purpose of making inspection or repairs to internal parts of motors, controllers, etc. When depended upon to permit frequent inspections it is desirable from a practical operating standpoint that the cover be easily and quickly removed and replaced. The position that been taken by the Bureau of Mines is that the questio of ease with which covers will permit inspection should be determined by the mamu- facturer and the user. If the scheme used requires considerable effort, as in the removal of several bolts, it has been assumed that the one going to all this trouble to get the covers off could be trusted to put the cover back in place properly, especially as the approval plate generally calls specific attention to this point. Where a cover is simply screwed in place, fastened by a single bolt, or secured by a hing in or other similar arrangement, the bureau has not been willing to assume that the, cover would in all cases be properly fastened and has required further security by means of a lock or seal. In the course of its investigations the bureau has had occasion to inspect and test five types of covers as follows: (1) Covers having two plane surfaces bolted together. (2) Covers having two plane surfaces held together by lugs, clamps, or other means besides bolts. (3) Covers which have screw thread and fit a similar thread in the compartment. (4). Covers having plane surfaces with the addition of a tongue-and-groove joint at about the center of the plane surface and in general secured by hinge pins or similar means of fastening. (5) Covers in the form of an annular ring accurately fitted to a motor shell which can be rotated around the shell, and thus make easy access to inspection openings in the shell and rotated back again to effectively seal these openings. Tests. have also been made of large bolted covers having a smaller and more accessible cover within the large one, which could be opened for inspection purposes.

May 1, 1930

By E. H. Hamilton

THE furnace on which the following investigation was based had dimensions 48 by 160 in., and was in continuous operation during the three days of the test. The average charge consisted of PER CENT. LB. PER HOUR Bed ore?14.5?2,980 Roast from Dwight-Lloyds?44.5?9,160 Siliceous ore?3.5?720 Iron flux?2.1?430 Battery plates?0.5?103 Lime rock?23.9?4,925 Briquettes?4.0?825 Scrap iron?2.1?430 M. P. slag?4.2?865 L. P.speiss?0.7?142 Total 100.0 THE furnace on which the following investigation was based had dimensions 48 by 160 in., and was in continuous operation during the three days of the test. The average charge consisted of PER CENT. LB. PER HOUR Bed ore?14.5?2,980 Roast from Dwight-Lloyds?44.5?9,160 Siliceous ore?3.5?720 Iron flux?2.1?430 Battery plates?0.5?103 Lime rock?23.9?4,925 Briquettes?4.0?825 Scrap iron?2.1?430 M. P. slag?4.2?865 L. P.speiss?0.7?142 Total?100.0?20,580

Jan 1, 1924

By F. Q. Su

Underground Coal Gasification (UCG) is a promising environmentally acceptable clean-coal technology. A typical UCG system has two wells drilled from the surface into a coal seam with some separation of injection from production. The wells are connected underground by various linking techniques. After creating a combustion reactor in an underground coal seam, air and oxygen flow through the injection well. Heat energy and gases are collected from the production well. As gasification progresses, the combustion reactor is moved along the linking hole. Using this process, the fracturing activity inside the coal seam serves an important role for enlargement of the gasification zone because the surface area oxidization increases continuously by coal cracking. For effective coal gasification, fracturing activity must be controlled. Moreover, excess fractures inside the coal seam and surrounding rock can induce gas leakage, underground water contamination, subsidence, etc. Therefore, monitoring and control of fracturing activity in underground areas constitute key technologies for efficient and safe UCG. To monitor fracturing activity, we conducted laboratory and small-scale field experiments of UCG using acoustic emission (AE) measurements. UCG model tests were conducted for linking and coaxial types UCG models. Coaxial UCG systems are compact and are anticipated for application in underground coal seams having a complex geological structure. The UCG model consists of a coal block molded in a steel canister (20 liter capacity) with heat-resistant mortar, with a linking hole or a coaxial-hole passing through the coal block. During coal combustion, coal temperatures, production gas contents, and AE activity were monitored under the control of injection-air and oxygen flow rates. Results show that the combustion propagated inside the specimen along the linking hole. Many AE events were generated during coal combustion. The AE activity was related closely to temperature changes inside the coal block. This AE generation apparently results from crack initiation and extension around the coal combustion area under the influence of thermal stress. However, comparing the results from UCG models of linking and coaxial types, the gasification of the linking type model showed an average calorific value as high as 11.3 MJ/m3. The coaxial type yielded an average calorific value of produced gas as only 5.79 MJ/m3. In the coaxial type of UCG model, the combustion region was limited to the area around the coaxial hole. The AE activity was lower than in the linking type model. For small-scale UCG field experiments, linking and coaxial types were tested at an open pit coal mine in Hokkaido, Japan. Using a linking type UCG, 58.2 kg coal was processed in 39 h, with the calorific value estimated as 11 MJ/m3. However, the coaxial type UCG processed 7.0 kg coal in 9 h, yielding an estimated calorific value of 6.0 MJ/m3. These tendencies resemble those of results of laboratory UCG experiments. Results of these experiments demonstrate that AE monitoring is a useful tool to evaluate combustion reactors for efficient and safe UCG systems. To develop a coaxial UCG system, results show that fracture control around combustion reactors is indispensable.

Aug 1, 2013

By Bradley Stoughton

A LL over our great country I have been privileged to see, during the last six weeks, the manifestation of a new spirit among engineers. Partly under the inspiration of leaders whose influence has been felt not only nationally, but internationally, - partly through the recognition of the service that engineers have been able to render to the nation during the recent crisis, a new self-consciousness has been acquired by the individuals, and now this self-consciousness seeks expression in opportunities for service and participation in public affairs. The engineer . no longer sees himself a mere reservoir of information to be tapped when some one is in need of cold facts, no. more an administrator of mere material things, but a potential administrator of- public affairs, a citizen and a human being, with the responsibilities, as well as the privileges of citizenship.

Jan 1, 1920

By Robert E. Ennis

Several important economic variables must be studied when planning a major underground conveyor haulage system if the objective of tow cost haulage is to be met. The purpose of this paper is to call these economic factors to the attention of the mine planner and encourage their serious consideration. To illustrate, the importance that some of these variables hole for the mine operator who wishes to reduce costs and maintain sound belt haulage practice, these areas of discussion will be covered. 1. Selection of economical flite lengths. 2. Economics of wire rope frame vs. rigid frame conveyors. 3. How idler design affects conveyor costs. 4. Economies in drive design. 5. How speed affects conveyor cost. 6. P.V.C. vs. Neoprene belt - what savings? 7. Maintaining, conveyor investment through maintenance. 8. Miscellaneous factors affecting the cost of belt haulage.

Jan 1, 1967

By Robert E. Goodwin

There are four main requirements to be considered in selecting a wire rope that will provide the best service. A proper choice is made by correctly estimating the relative importance of each of these requirements and choosing a rope with qualities that will best enable it to withstand the combination of destructive forces expected under continued service. A Good Rope Choice Matches Strength with Stress A wire rope should be (1) strong enough to sup- port the maximum load anticipated with a proper safety factor, (2) able to withstand bending and to resist bending fatigue without failure of the wires, (3) able to withstand surface abuse such as abrasion, pounding, and wire scrubbing, and (4) able to take abuse such as crushing and distortion.

Jan 5, 1969

By Marvin L. Whisman

Several parameters controlling the reproducibility of tritium determina¬tion in organic compounds by liquid scintillation counting were evaluated by the Federal Bureau of Mines. These included optimum volume of scintillator solution for maximum counting efficiency, reproducibility of counting a sealed commercial standard and comparison with duplicate counts on laboratory-prepared samples. The error introduced by using microliter pipets, optical differences in counting vials, reproducibility of counting organic samples where quenching is a factor, reproducibility of counting laboratory-prepared samples with an added internal standard, optimum ratio of internal standard activity to sample activity, effect of sample volume upon counting efficiency, count rate at which coincidence losses become apparent, and reproducibility of organic compound radioassay by the standard addition technique are outlined. From the evaluation of these parameters, a technique that can be applied routinely to organic compounds containing tritium has been established, and details are included in this report.

Jan 1, 1961

By E. J. Wasp, T. L. Thompson, T. C. Aude

The paper will deal with some of the more important technical aspects of slurry pipelines as they apply to the mineral field. In addition, the use of these technical concepts in arriving at realistic economic figures will be discussed.

Jan 1, 1970

"The objective in controlled blasting is to reduce overbreak to control the final pit wall slope, shaft, drift ditch, bench, etc. to the final planned excavation limit. The six main types of controlled blasting utilized today are:1. Line Drilling2. Cushion Blasting3. Smooth Wall Blasting4. Buffer Blasting5. Presplitting or Preshearing6. Air Deck Presplitting"

Jan 1, 1994

Laboratory tests were conducted in a full-scale continuous miner test gallery to evaluate resulting dust levels for changes in face airflow, spray water quantity and pressure, and mining height. The minimum and maximum values tested for each parameter were as follows: airflows between 1.42 and 6.14 m3/sec, water flows between 56.8 and 132.5 lpm, nozzles pressures between 413 and 1379 kPa, and mining heights between 1.52 and 2.74 m. Each of these parameters were evaluated for four common spray system designs. Respirable dust samples were collected in the operator&apos;s cab on the miner and in the immediate return. Second-order polynomial models were used to represent expected dust levels and multiple stepwise regression was used to identify significant control parameters for inclusion in the models. Separate models were developed for dust levels at the operator and return locations and for each individual spray system. Interaction between control parameters and curvature effects were found in most models. The analysis indicated that at the operator location, airflow and mining height had the most significant impact on respirable dust levels. In the return, airflow and water pressure were typically the most significant parameters. The models developed for each spray system design can be used by mine operators to guide application of control parameters for a variety of operating conditions and mining heights.

Jan 1, 1994

By Yuting Xue, Alper Kirmaci, Taghi Sherizadeh, Khaled Mohamed

Resin-grouted bolts serve as a crucial means of stabilizing yielded coal ribs in underground coal mines. A comprehensive investigation into their efficacy was undertaken by a collaborative effort between the National Institute for Occupational Safety and Health (NIOSH) and Missouri University of Science and Technology (MST). This study involved pull-out tests in multiple locations, including six coal mines and the NIOSH research mine. A total of seventy-three (73) tests were conducted, of wide range of anchorage lengths, ranging from a short encapsulation length of 0.305 m to a fully grouted encapsulation length of 1.524 m. The test findings indicate that when short encapsulation bolts are installed at high rotation speeds, their anchorage capacity is significantly reduced, leading to failure at the bolt-grout interface. Conversely, when these bolts are installed at lower rotation speeds, they exhibit greater capacity, with failure occurring at a higher anchorage load equivalent to the yield load of steel rebar. No matter what the rotational speeds were used during bolt installation in this study, the fully grouted bolts consistently experienced failure at the ultimate load of the steel rebar. Most of the tests carried out on partially grouted bolts with anchorage lengths of 0.610 - 0.914 m have shown behavior patterns like the fully grouted bolts, although exhibiting reduced stiffness. The outcomes of this research offer a profound insight into the ways in which resin-grouted bolts enhance the stability of coal mine ribs.

Feb 1, 2024

By T. Rahimzadeh, C. W. Trueman, S. Farzaneh, S. V. Hoa, I. Abdalla

This paper presents the shielding effectiveness (SE) of woven continuous carbon/epoxy composite materials. The theoretical and physical concepts behind the experimental results are demonstrated in details. The influence of frequency, the overlapping angle between overlapped layers and the number of overlapped layers upon the EMI shielding of composite sheets are discussed. In this work, in particular, the epoxy layers are considered as dielectric apertures of the conducting carbon fiber slab for the interpretation of the experimental results. The experimental results, using ASTM standard D4935-89, indicate that the SE can reach values greater than 90 dB above 500 MHz.

Jan 1, 2006