Search Documents

By E. Tabosa, S. Vianna, K. Duffy, W. Valery, B. Andrade, L. Pyle, P. Holtham

Pneumatic flotation cells are high-intensity flotation machines with rapid kinetics, resulting in short residence times. Examples include the Jameson, PneuFlot and ImhoFlot cells. These cells do not use impeller-like mechanical cells. Rather, the air and pulp are mixed in a continuous stream of high fluid velocity through a downcomer or venturi to disperse the air into fine (approximately 0.5 mm) bubbles and maintain particle suspension. Froth wash water is often used to enhance concentrate grade, minimising recovery by entrainment. With the growing application of these types of cells, not only in cleaner stages (their traditional use) but also in pre-flotation and scalping duties, there is a need to predict their performance more accurately for circuit design and optimisation. No widely accepted model for pneumatic flotation cells is available and their metallurgical performance is often scaled up from laboratory and/or pilot plant testing by assuming fixed values for metal recovery, concentrate grade and concentrate percent solids. This paper describes a new approach to simulate pneumatic flotation cell performance and presents case studies demonstrating its applicability. Keywords: Pneumatic flotation, flotation modelling, flotation circuit design, flotation circuit optimisation, Jameson cell

Jan 1, 2020

By BHAMIDIPATI S. SASTRY, Pavan Kumar Kattamuri, ADITYA PANDEY

The thermal conductivity of rock surrounding the airway is one of the most important thermal properties for estimating strata heat transfer into the mine air and for designing the air-cooling strategies. Several laboratory methods are available for the determination of thermal conductivity; however, most of them are complex and cumbersome. The present study explains the working principle of Lee’s apparatus which is relatively simple, easy to fabricate and use, and provides consistent results. In the present study, thermal conductivities of sandstone cores obtained from an Indian coal mine are determined using Lee’s apparatus. An approach is discussed for determining the temperature gradient of sandstone specimens while cooling and used for calculating thermal conductivity. The thermal conductivity of different sandstone specimens attains values between 2.37 and 2.59 W m− 1 °C−1. For different sandstone cores obtained from the field, properties including specific gravity, specific heat capacity, thermal diffusivity, and porosity, along with thermal conductivity, are determined and highlighted in this study.

Jul 20, 2021

By Joshua R. Omer

A numerical model is developed for predicting the load transfer and settlement behaviour of vertically loaded, bored cast in-situ piles. Based on analysis of full-scale pile tests, closed-form equations are formulated to uncouple the shaft and base transfer resistance components of the pile/soil system. Appropriate parameters are introduced to take into account: (i) the shaft resistance distribution in unlined and partially lined piles, (ii) the effects of ?soft toe? (voided toe pile) behaviour on base resistance development. For convenience, an interactive computer program has been developed in Matlab? with a user friendly interface system. The program can be applied to predict the complete load-settlement curve and axial force distribution in bored cast in-situ piles if reliable soil test data are available. To demonstrate its validity, the proposed method is applied to 4 test piles, which are also analysed using two previously published methods: (a) elastic solution method and (b) layer discretisation method. Methods (a) and (b) above are based on load transfer (t-z) and finite element models respectively. It is shown that the proposed method yields axial force distributions and load-settlement curves that are in good agreement with the observed pile test data.

Jan 1, 2010

By R Van Laeren, G Langerak, S Fityus, K Koosmen

Co-disposal of partly-dewatered mixed-plant rejects (MPR) from coal processing into spoil dumps is gaining favour amongst Australian coalmine operators in preference to conventional tailings disposal methods which require a tailings dam. Owing to their often low permeabilities and high degrees of saturation, MPR materials may be prone to the development of excess pore pressures when covered by spoil during routine dump advancement. The likelihood of dump failure will increase if these pore pressure regimes and the associated delay of shear strength development are not accounted for during waste dump design. To date however, little is known about these pore pressure regimes due to the complexities associated with their in situ measurement.This paper describes the in situ measurement of pore pressures in a cell of MPR placed within a coalmine spoil dump. Four vibrating wire piezometers (VWPs) were placed within a cell that was then filled with MPR and allowed to consolidate under self-weight before advancing an adjacent tiphead across the cell. The VWPs recorded the transient pore pressures during MPR placement and dump construction, and their interpretations are described within the context of laboratory measured parameters. Following analysis of the measured pore pressures, their implications on shear strength and dump design are also discussed.CITATION:Koosmen, K, Langerak, G, Simmons, J, Fityus, S and Van Laeren, R, 2015. Field measurement of transient pore pressures within co-disposed processing rejects placed in a spoil dump, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 63–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Mahaboob Basha Shaik, Shakuntala Tudu, Indrajit Paul, Chandra Sekhar, Neha Gupta, Amit Kumar, Srinivas Dwarapudi, Arvind Kumar Patel

In this study, the effect of colemanite and calcined colemanite (CC) addition on the properties of iron ore pellets is studied. The pellets are prepared in a lab without and with 0.2% colemanite and varying amounts of CC from 0 to 1.0 wt%in steps of 0.2%. A reference pellet is prepared under typical plant conditions, and the properties of the reference pellet are considered as the base value for improving the cold compressive strength (CCS) while maintaining the other parameters at an acceptable limit without altering the pellet. The study also aims to provide a detailed characterization of colemanite and calcined colemanite to better understand their behaviour during firing. The lab-scale results show that the CCS of pellets made with 0.2% colemanite was reduced by 222 points (60%) as compared to the reference pellets due to crack formation during firing. The results show an improvement in the CCS of the indurated pellets with CC dosage up to 0.4%, and decreasing strength is noted thereafter. It is observed that the swelling index increases with the increase in calcined colemanite dosage. To simulate plant conditions, reference pellets and pellets with optimized CC dosage were fired in a plant furnace.

Oct 16, 2020

By Reno H. Sales

Since leaving school my efforts have been geared to the task of making geology useful to the mining industry. The responsibility of the economic geologist or mining geologist of today has grown to be more, than that of merely finding a faulted segment of a vein. The very life of our mining industry is at stake. The tremendous progress in every branch of our modern civilization has been made possible through the developments in the use of metals. Many of our great industries, including that amazing field of aircraft production live and thrive only because of metals.

Jan 1, 1942

By Sales, Reno

Since leaving school my efforts have been geared to the task of making geology useful to the mining industry. The responsibility of the economic geologist or mining geologist of today has grown to be more, than that of merely finding a faulted segment of a vein. The very life of our mining industry is at stake. The tremendous progress in every branch of our modern civilization has been made possible through the developments in the use of metals. Many of our great industries, including that amazing field of aircraft production live and thrive only because of metals.

Jan 1, 1942

By J. C. Duchon

The use of extended workdays or compressed workweeks (regular shift lengths exceeding 8 h) is attracting growing interest in many industries using continuous operations. While extended workdays promise increased worker satisfaction due to more days off, including weekends and holidays, there are legitimate concerns about the potential effects on the health and safety of such a schedule. The U.S. Bureau of Mines (USBM) conducted a study at a Canadian underground copper, lead, and zinc mining operation that was designed to study the safety and performance implications of extended workdays. Measures were taken before and after a change from the old 8-h continuous schedule to the new 12-h continuous schedule, including behavioral performance measures to analyze perceptual-motor changes, continuous heart-rate monitoring and aerobic capacity to measure physical fatigue, a variety of self-report questionnaires to measure perceived adaption and satisfaction with the new schedule, and pulmonary-respiratory measures to examine air contaminant exposure. Based upon the overall acceptance of the new schedule by the workers and lack of change in fatigue-sensitive behavioral and physiological performance measures, this study recommends that the mine retain the 12-h schedule. However, certain precautionary measures are suggested to insure the safety of the workers.

Jan 1, 2010

By Edwin C. Reeder

This is one of a series of papers dealing with mining methods and costs prepared under the sponsorship of end in cooperation with the United States Bureau of Mines. The mining methods described in this paper are those used in one of the large mines producing fluorspar in the Kentucky-Illinois fluorspar field, located in southern Illinois and western Kentucky on the Ohio River. The occurrence of ore and the methods of wining are similar to those in other mines in the district; therefore information regarding methods and the results obtained should be of interest. Improvements in methods have been made as experience developed the need of them. The trine is situated at Rosiclare, Ill., on the Illinois Central Railroad, and shipments are also made b r barge on the Ohio River.

Jan 1, 1930

16.1.1-VENTILATION'S ROLE Importance of Ventilation and Environmental Control-Mine ventilation is necessary for the preservation of human life and for the conduct of operations involved in the underground extraction of minerals. It clearly is the most essential of the functions attendant to mining, yet it is auxiliary to the primary objective in mineral extraction. Ventilation in mining thus poses a paradox: ideally, it should be carried out with minimum interference with and cost to production operations, yet it is absolutely vital in providing adequate environmental con¬ditions to support mining. Deterioration of the atmosphere, along with rising ground pressure, imposes the ultimate constraint with depth in underground mining. Ventilation requirements and costs rise rapidly with depth. To preserve atmospheric quality under intense heat conditions, ventilation at great depths must be supplemented by air condition¬ing. Likewise, when mining at any depth under severe or excessive conditions of gas, dust or humidity, supplementary control measures must be employed. In recent years, environmental standards in mines have been raised substantially. While limits are based on human tolerance, increasing concern is being expressed for standards of human comfort. The reasons are economic, as well as humanitarian. Worker performance and longevity correlates closely with environmental quality. Further, adverse accident and insurance compensation rates are a consequence of unsatisfactory environmental conditions. No mining company can afford to be lax in its environmental and ventilation practices. Functions and Processes-Ventilation is the control of air movement, its amount and its direction. As a means of quantity control, it is one of the constituent processes of total air conditioning, the simultaneous control within prescribed limits of the quality, quantity and temperature-humidity of the air. Ventilation is the most common and most. important conditioning process employed in mines for air environmental control. In mine ventilation, air is coursed through the mine workings and openings themselves and, for auxiliary purposes, through vent tubing and ducts. Thus, many interdependencies exist between the mining system and ventilation method. In fact, the two often have evolved ,jointly, as in room-and-pillar extraction of bedded or tabular mineral deposits, such as coal. Ventilation in mines today is provided almost exclusively by large fans, although air flow may result due to natural (thermodynamic) conditions. As mines increase in depth, size and complexity, demands on the ventilation system to maintain more stringent standards of environmental quality likewise rise. On the other hand, never have the technology and resources of the mining industry to cope with environmental problems been so well developed as they are today. In spite of rising costs, it is unlikely that further progress in mine ventila¬tion and air conditioning must await technological breakthroughs. 16.1.2-NATURE OF THE MINE ATMOSPHERE Air Mixtures-Air is a gaseous mixture comprising the natural atmosphere at the surface of the earth. Thermodynamically, it may be thought of as a mech-

Jan 1, 1973

By W. P. Yant

The hazard to health from contamination of air by a noxious gas depends not only on the potential harmful response attending exposure, but also on the warning properties, which in effect may be termed the "accompanying warning response," This warning may be manifested as an odor, taste, irritation of the eyes, nose, or throat, or perhaps headache, vertigo, or nausea. These manifestations may be painful and even slightly harmful, but to a much lesser degree than the primary injury of exposure. The warning response mitigates hazards directly in proportion to the degree of Intolerability which accompanies injurious exposure, and accordingly its absence augments hazards. This accounts for the fact that the actual health hazards from a non-odorous or non-irritating gas or vapor of comparatively low toxicity sometimes equal or exceed the hazard from a considerably more toxic substance, but one which possesses a marked odor or produces eye, nose, or throat irritation in advance of harmful exposure. When a substance lacks the properties for giving warning, it is often possible to impart them by the addition of a small amount of another substance which has an exceedingly high warning intensity. The vapors of this substance, commonly termed a "warning agent" or "tracer gas," escape and mingle with the gas or vapor which lacks warning properties and thereby apprises persons of the latter's presence. The amount of the warning agent added is that which will give adequate warning in advance of serious physiological harm from the dangerous gas or vapor.

Jan 1, 1930

By Qingwei Joshua Ong

Tension piles, also known as uplift or anchor piles, are necessary to resist uplift forces that might cause structural distress. In excavation projects, most uplift forces are developed because of hydrostatic pressures, and so tension piles are subjected to a great deal of tensile forces. Most current methods of design for tension piles completely neglect the tensile strength contribution of concrete, relying only on the steel members to carry the tensile stresses, resulting in an overly conservative design. The stressstrain behavior of the composite material of concrete and steel must be considered for a realistic simulation of tension piles. This paper will examine a case on a tension bored pile in typical soft clay to demonstrate the importance of considering the tension strength and tension softening of the concrete.

Nov 1, 2022

By R. L. Bullock

The New Lead Belt of Missouri, situated in the heart of the Clark National Forest, stands as a dynamic example of how mining activities can successfully coexist in a restricted wilderness area. After 16 years of intensive drilling activity, mine development and surface plant construction, many would agree that the mine-plant design philosophy of St. Joe has minimized the imbalancing effects to the ecology and the wilderness appearance of the Ozark area. In a recent dedication speech of St. Joe's newest operation, it was stated: 1 "this Brushy Creek Mine, as well as nearly all of the mines in this district, lies within the boundaries of the Clark National Forest. Here the Forest Service has an outstanding and realistic program for multi-use of Federal lands. Mining, lumbering, recreation and conservation coexist in, what I consider, a delightful wilderness environment. I believe that this same type of usage could be permitted on all government land without seriously detracting from its natural beauty." Each and every activity in the process of discovery, exploration, development and finally operating a mine and process mill could have drastically degraded some phase of nature's environment were it not for the well developed and executed plans of the mining people involved. This is not to say that everything has been kept in perfect balance; but most certainly the industrial impact on what was once a wilderness area has been held to a minimum. What follows is the story of how each phase of this gigantic development was handed by industry people. Through their interaction and cooperation with government agencies, educators and researchers, allowed not only the ecology of the area to be protected, but the aesthetic beauty of the Ozarks to remain intact.

Jan 1, 1973

By David M. Gullikson

Since publication of the paper on the composition of California oilfield waters by Jensen (6)3/ in 1934 the only other information on the subject was published recently by Chave (4). To supply needed information on the composition of California waters in areas of current drilling activity, the Federal Bureau of Mines collected formation water samples for analysis. Thirty-eight samples from oil-and gas-producing formations in 12 fields located in Ventura, Kern, Glenn, and Colusa counties were analysed by the Bureau's San Francisco Petroleum Research Laboratory. The samples were selected particularly from fields where the water composition was not well known or where interpretation of electrical logs has been difficult and the interpretation may be affected by unusual composition of the water. These samples were obtained from rocks ranging in geologic age from Cretaceous to Upper Pliocene. Fifteen constituents of these waters were determined including sodium, potassium, calcium, magnesium, strontium, barium, lithium, chloride, iodide, bromide, carbonate, bicarbonate, sulfate, borate, and residual acidity. These analyses are the first to be published on California oilfield waters in which determinations for potassium, strontium, bromide, iodide, boron) and naphthenates were made on a significant number of samples. The electrical resistivities of tae samples were determined at 75° F. and 175° F.

Jan 1, 1961

By D. Harrington

Although the hysteria. with regard to silicosis end other occupational diseases seems largely to haws passed, and more careful sober consideration is being given this subject, it would be very poor policy for any employer to take the stand that the storm has blown over and that he can safely relax and revert to the status of 5, 10, or more years ago in such matters. The real fact is that occupational-disease compensation is nor in its infancy and can be expected to grow by leaps and bounds. At present, while 46 States of the Union3/ and the District of Columbia have compensation acts, only the following have some fern of occupational-disease legislation: California, Delaware, Connecticut, District of Columbia, Illinois, India a, Kentucky, Massachusetts, Michigan, Minnesota, Missouri, Nebraska, New Jersey, New York, North Carolina, North Dakota, Ohio, Pennsylvania, Rode Island, Washington, West Virginia, and Wisconsin. Silicosis appears to be compensable under those acts in California, Connecticut, District of Columbia, Illinois, Kentucky, Massachusetts, Missouri, New York, North Carolina, North Dakota, Ohio, Pennsylvania, West Virginia, and Wisconsin; possibly it may be interpreted as compensable in others. Occupational-disease legislation (largely relating to silicosis) has seen under consideration in some form relatively recently in Arkansas, California, Delaware, Idaho, Maryland, Kansas, Massachusetts, Michigan, Minnesota, Montana, Nebraska, New Jersey, Ohio, Pennsylvania, Tennessee, Utah, and. Washington at least. It will be surprising if comparatively broad or inclusive occupational-disease legislation will not be on the statute books of nearly every State in the Union within the next 5 years. With this situation confronting him, the far-sighted industrialist who has the best interests of his organization at heart will immediately begin to "put his house in order," if he has not already done so, by studying possible occupational-disease hazards to his employees; moreover, he will promptly apply all known remedial measures or will attempt to devise such measures if none of those already devised seem to apply to his establishment.

Jan 1, 1939

By S. M. Woodring

Research objectives included 1) determine relationships if any between spectral response of soil and soil textural groups, Unified Soil Classification subgroups and selected landforms and 2) develop computer assisted techniques for engineering soils mapping of remotely sensed data. The sire in northeastern Kansas, 1.6 Km by 43 Km (1.0 mi by 27 mi), contained glacial and alluvial soils. Multispectral scanner data (0.40 to 1.80 pm) collected at 915 meters altitude (3,000 feet) were analyzed using two distinct computer techniques: the nonsupervised approach involving delineation of soil training areas directly by computer and the supervised approach entailing training area selection manually by the researcher. Computer classification of surface materials follows both methods. Non supervised analysis results failed to show a consistant relation- ship between landform type and soil spectral class. Landforms correlating well displayed either unusually bright or unusually dark spectral signatures. Supervised analysis results showed a strong relationship between soil texture and soil spectral class. A moderately strong tie was shown between engineering soils groups (ML, CL, CH and OH) and their respective spectral classes, and a weak association between landform type and soil spectral class. An analysis procedure for engineering soils mapping by computer of remotely sensed data was developed. 1. Locate cultural features by visual examination of imagery. 2. Produce generalized bare soil-vegetation- water map using nonsupervised technique. 3. Outline significant soil fields for computer training using supervised approach. 4. Computer-classify entire area based on these soil fields.

Jan 1, 1974

By Timothy M. Bruner, William J. Maloney

Faced with rapid growth that strained their current water supply capabilities, the Somerset Water Service in Somerset, KY decided to construct a new intake structure on the shore of Lake Cumberland. With an existing intake structure within 200', very hard limestone geology with calcite geodes, and lake level fluctuations as high as 50 ' ,this project posed many challenges. The following paper discusses how mechanical excavation techniques were used to overcome these obstacles.

Jan 1, 2001

By Phillip R. Mulligan, Catherine Johnson, Edward Kinzel, Cody Lough, Jason Ho

A shaped charge is an explosive device used to focus detonation energy in a desired direction. Shaped charges have numerous applications in several industries such as oil extraction, weaponry and demolition. The focusing of the detonation energy is the result of the Munroe Effect, which greatly increases the penetration properties of the explosive due to a void in the explosive’s volume. The void in the explosive is lined with a metal substrate that becomes a super-heated projectile when the explosive is detonated. Additive Manufacturing (AM) can allow greater design freedom and geometric complexity for the liner portion of the shaped charge. Specifically, hierarchical structuring and functional grading can potentially provide greater velocity, directionality, and efficiency. By utilizing AM, the conventional use of shaped charges can be greatly expanded upon and may open new possibilities. In this work, selective laser melting (SLM) was used to explore different conical shaped charge (CSC) liners made out of stainless steel 304L. A series of liners were tested that had varying densities and were compared to conventional liners. The CSCs were filled with the high explosive Composition C-4 and detonated to evaluate performance. The blast events were recorded using break wire screens to calculate the velocity of the jet through steel target plates over a standoff of 6 times the charge diameter. A high-speed camera recorded the blast event to calculate the velocity of the jet through the air. The depth of penetration into the steel target plates was also used as a measurement of the effectiveness of the CSCs. The aim of this work is to show the potential for advanced shaped charges produced using SLM.

Jan 1, 2019

By J. H. Bilbrey

A recording thermobalance ,vas used to determine the rates of oxidation of mol-ten tin over the temperature range 550°-900° C. Oxidation rates were found to vary widely for a given temperature, as previously reported by other investigators. 1 X-ray diffraction data indicated that the probable cause of these variations was the development of preferred orientations in the crystals forming the oxide film. No reasons for the differences in degree of preferred orientation were discovered. For relating the weight of the oxide formed (w) to the time of oxidation (t) an equation of the form wn = kt was found to best represent the experimental data. INTRODUCTION In the course of conducting investigations on the feasibility of using selective oxidation techniques for the purification of various metals in the molten state it was soon discovered that data on the oxidation of molten metals and alloys were very scarce. In contrast to the many hundreds of publications on the oxidation of metals in the solid state there are relatively few articles on the rates of molten-metal oxidation. In view of this scarcity of data, it was decided to institute a series of investigations into the oxidation processes of molten nonferrous metals and alloys with the expectation that the information derived could be put to practical use in developing and improving refining processes based on selective oxidation. This report is the first of a series in which oxidation data for molten nonferrous metals and alloys are presented.

Jan 1, 1955

By A. E. Bellis

THE CHAIRMAN (ALBERT SAUVEUR, Cambridge, Mass.).-Any information likely to throw light on the constitution and proper treatment of high-speed steel in order to obtain maximum results, should surely he welcomed. All users of high-speed steel, I believe, will agree with the authors that, in order to obtain satisfactory results, it is not sufficient to heat all brands of high-speed steel to one and the same temperature; apparently very slight differences of chemical composition seem to call for marked differences in temperature. I think that all of us agree that a properly treated piece of high-speed steel should have a fine austenitic or polyhedral structure and that an appreciable quantity of free carbide may be present in the case of very high tungsten steels. What we seem to lack is a satisfactory method, quick and reliable, of ascertaining when the proper structure has been obtained. I think Mr. Bellis' paper is a step in the right direction. To the untrained eye, however, it is not an easy matter to select from some of his photomicrographs the one representing the best structure; for instance, in the case of steel A, we wonder why temperatures of 2,250 and 2,300 do not yield the same results, seeing that both structures are apparently alike, and the same might apply to some of the other samples. I have no doubt, however, that the experienced observer is capable of detecting structural differences that are not made plain here and by which he is able to select the proper quenching temperature. COLIN G. FINK, East Orange, N. J.-On page 68 the authors say that the use of a barium chloride bath to eliminate this difficulty has the disadvantage that the surface of the tool becomes decarbonized." I would like to ask whether they actually found that the surface was decarbonized, or whether they base this conclusion on softening alone? A. E. BELLIS, Springfield, Mass.-No, we have never demonstrated that it was a decarbonization, it is just the softening of the steel. The addition of ferrocyanide to the ferrochloride bath has been suggested. I think that is not altogether satisfactory, because the ferrocyanide bath changes composition very rapidly at these high temperatures, and it would be just a question of luck whether or not it had too much or too little ferrocyanide in the bath giving equilibrium with the carbon content.

Jan 4, 1917