Search Documents

By H. A. Schwartz, W. Kenneth Bock

In this paper it is shown that when the tensile strength of a given steel in various states of heat-treatment is plotted against its elongation, a straight line results. The equation of this straight line can be computed with considerable accuracy from its chemical composition. The appropriate equations are given. The logarithm of the slope of the tensile-strength locus is shown to be proportional to the cumulative effect of the total alloy addition and the vosition of the line to be directly proportional to the cumulative effect of the alloy content. It is further pointed out that heat-treatment is more effective than composition in determining yield ratio. The latter enters mainly by its effect on hardenability, which is briefly discussed. Reduction of area and Brinell number are given some incidental attention. The data are applicable only to steels that have been normalized and/or quenched. The steels, if normalized, may or may not have been tempered. If quenched they must have been tempered at or above 4oo°C. (75o°F.). Introduction Cast steels vary in composition and frequently are used in various states of heat-treatment. It is obviously important to be able to predict the compositions that might accompany specific engineering properties by suitable selection of heat-treatments. For cast steels, which are of necessity produced heat by heat in accordance with the particular requirements of the castings to be poured, there has been, happily, much less tendency to standardization than for rolled products, whose destination is not necessarily known when particular ingots are made or rolled. It is of distinct advantage to the steel foundry-men to be able to make steel of given properties, using alloys that can be recovered from scrap, or most conveniently or cheaply bought, rather than a particular formula adopted in the interest of standardization. The heat-treatment appropriate to securing a given result in a given steel is well known to be closely related to composition. For example, molybdenum steels are not much softened by tempering except at rather high temperatures. Highly alloyed steels are "air-hardening," and on cooling in air behave like carbon steels that have been quenched. With these matters, we do not concern ourselves in this paper, although we recognize their importance. The entire picture evidently will be very complex and can be brought within accurate understanding only if our knowledge of test results can be coordinated in terms of general principles.

Jan 1, 1944

By H. A. Schwartz, W. Kenneth Bock

In this paper it is shown that when the tensile strength of a given steel in various states of heat-treatment is plotted against its elongation, a straight line results. The equation of this straight line can be computed with considerable accuracy from its chemical composition. The appropriate equations are given. The logarithm of the slope of the tensile-strength locus is shown to be proportional to the cumulative effect of the total alloy addition and the vosition of the line to be directly proportional to the cumulative effect of the alloy content. It is further pointed out that heat-treatment is more effective than composition in determining yield ratio. The latter enters mainly by its effect on hardenability, which is briefly discussed. Reduction of area and Brinell number are given some incidental attention. The data are applicable only to steels that have been normalized and/or quenched. The steels, if normalized, may or may not have been tempered. If quenched they must have been tempered at or above 4oo°C. (75o°F.). Introduction Cast steels vary in composition and frequently are used in various states of heat-treatment. It is obviously important to be able to predict the compositions that might accompany specific engineering properties by suitable selection of heat-treatments. For cast steels, which are of necessity produced heat by heat in accordance with the particular requirements of the castings to be poured, there has been, happily, much less tendency to standardization than for rolled products, whose destination is not necessarily known when particular ingots are made or rolled. It is of distinct advantage to the steel foundry-men to be able to make steel of given properties, using alloys that can be recovered from scrap, or most conveniently or cheaply bought, rather than a particular formula adopted in the interest of standardization. The heat-treatment appropriate to securing a given result in a given steel is well known to be closely related to composition. For example, molybdenum steels are not much softened by tempering except at rather high temperatures. Highly alloyed steels are "air-hardening," and on cooling in air behave like carbon steels that have been quenched. With these matters, we do not concern ourselves in this paper, although we recognize their importance. The entire picture evidently will be very complex and can be brought within accurate understanding only if our knowledge of test results can be coordinated in terms of general principles.

Jan 1, 1944

By D. Men, R. Q. Honaker, J. C. Hower

"Maceral separation is one possible technique to expand coking coal resources, either by increasing the blending ratio of non- or slightly caking coal or rationally utilizing the coking coal according to the different behaviors of macerals in coking. The success of maceral enrichment for a given coal using flotation is dependent on the differences in flotation kinetic rate among macerals. This paper presents the flotation rates and zeta potentials of the vitrinite-rich and inertiniterich maceral concentrates obtained from six coal samples of different ranks – from high-volatile B bituminous coal with mean random vitrinite reflectance (Rrandom) of 0.64 percent to low-volatile bituminous coal with Rrandom of 1.73 percent – using a float-sink procedure. The flotation results show that vitrinite-rich concentrates can be produced in tap water using froth flotation only with frother for the high-volatile B and A bituminous coal samples, but there was no good performance for the high-volatile C bituminous and medium- to low-volatile bituminous coal samples. The zeta potential results show that froth flotation could probably separate the high-volatile C bituminous coal samples well by adjusting pH, but there was no good performance for the higher-rank coal samples. IntroductionMetallurgical coke is used in blast furnaces for steel production and is produced by the carbonization of coking coal. Because caking coals are rare and expensive, they are often blended with non- or slightly caking coals. Considering the tight supply-demand situation for coking coal in China, it is important and urgent to develop highly efficient technologies for rationally utilizing and expanding coking coal resources (Mochizuki et al., 2013)."

Jan 1, 2015

By A Harburg, A Dendys, G Green

Dugald River Mine (DRM) is located approximately 85 km north-east of Mount Isa, and 65 km northwest of Cloncurry, in the north-west Queensland Minerals Province of Australia. DRM is an underground operation and includes an above ground processing area, a 200 ha tailings facility, two waste rock dumps and associated infrastructure. The mining method is conventional underground longhole open stoping and downhole benching of a lead/zinc deposit within a black slate environment. The deposit is estimated to contain ~53 Mt of zinc and lead, which will be mined over a 30-year period. During operations, waste rock is segregated into either Potentially Acid Forming (PAF) or Non-Acid Forming (NAF) based primarily on the sulfide concentration of the rock. In particular, the NAF waste rock is an asset and is used for various small construction projects during operation; however, its primary use is for rehabilitation work at closure. Since beginning operations in 2017, DRM has generated more NAF than was originally anticipated. Whilst this is an excellent asset to DRM, it did pose a logistical problem of where to store the additional NAF for the life-of-mine and how to manage the run-off. DRM experiences distinct wet and dry seasons with hot conditions and periods of rainfall between November to April, and relatively dry and mild conditions between May to October. Majority of rainfall is received between January and February with an annual average rainfall of 501.1 mm. Short and intense rainfall events are common. DRM’s above ground infrastructure is land-locked between two large ephemeral watercourses, making the significant expansion of any assets challenging from a permitting/regulation and cost perspective. MMG is also a member of the International Council on Mining and Metals (ICMM) and is committed to adapting to a changing climate through operations and closure. Following extensive studies DRM opted to store the additional NAF material into the adjoining NAF Dam and concurrently upgrade a previously minor sediment basin into a highly engineered sediment basin which relies on automatic flocculant dosing to meet the required discharge quality limits. This basin is climate-resilient in that the dosing system can be adjusted to counter high intensity extended rainfall events which produce highly variable inflow water quality. This abstract broadly describes how DRM designed and implemented an engineering innovation to enable the site to meet the changing climatic challenges. The abstract then describes the process to design the sediment basin and how the dosing rate was established and validated. Finally, the abstract comments on the effectiveness of the sediment basin and how it has revolutionised DRM’s approach to water treatment and management; all whilst minimising the disturbance footprint of the operation

Aug 2, 2023

By Edgar Dernedde

Cryolitic melts at a temperature of about 960 °C are used in reduction cells to dissolve alumina and to produce primary aluminium. At these temperatures cryolitic melts with an acidic composition have a significant vapour pressure, which contributes substantially to the evolution of fluorides from these cells, The Antoine equation is commonly used for relating vapour pressure data of liquids at different temperatures, It is also applicable to cryolitic melts, Published equations have at least 20 numerical constants, in order to allow for the effects of melt composition. In the present work a simplified equation with only 12 numerical constants was developed and is applicable for multiple additions to molten cryolite up to 30 wt %, The simplified equation was compared with the published equations of Haupin & Kvande and Gustaysen & Ostvold using 472 vapour pressure data of cryolitic melts. Results showed that the simplified equation has the same accuracy as the published equations in the composition range of interest to industry.

Jan 1, 2004

By A. D. Rovig

Metallurgical evaluation of autogenous grinding of Anaconda's Berkeley Pit ores indicated that tonnage throughput increases, at a finer flotation feed size, were possible by converting autogenaus mills to steel ball mills. In addition, initial test work showed that the improved grind resulted in slight recovery gains in subsequent flotation processing.

Jan 1, 1974

By F. R. Lee

THE Bureau of Mines was established in July 1910 to conduct research and to establish standards for mining equipment and practices which would conserve human life, natural resources, and property in the mineral industries. Several lists of equipment approved by the Bureau as permissible for use in gassy coal mines have been issued since then. The lists covering all approved equipment except breathing apparatus and explosives have born consolidated into two publications: Bulletin 343. Permissible Equipment Approved to January 1, 1953, and Information Circular 8220, Permissible Mina Equipment Approved By The Bureau of Mines During 1953-62. The, purpose of this publication is to supplement Bulletin 343 and Information Circular 8220 with a listing of permissible equipment approved during 1963 and 1964. The schedule, (standards) under which equipment listed herein have been approved are, as follows (cities and dates of approval and revision are, given in footnotes) : Schedule 2F,3 schedule 6D,4 schedule 7C,5 schedule 8C,6 schedule 9B,7 schedule 10C,8 schedule 12D,9 schedule 22,10 schedule 24,11 schedule 25B,12 schedule 25B,13 schedule 29A,14 schedule 30,15 and schedule 31.16

Jan 1, 1966

By E. A. van Wyk, M. R. de Villiers

"Mining companies strive to increase and maintain production, while simultaneously remaining competitive in the global economy. Furthermore, they must ensure workers’ safety and maintain good safety records. The use of virtual reality (VR) facilitates the development of tools and systems for various purposes that can improve knowledge and understanding of the work environment. VR is a rapidly growing technology that uses the ever-increasing power of computing to simulate real-world and imaginary environments and situations with a high degree of realism and interaction. The availability of 3D modelling tools and simulation programming engines that work effectively with a mid-range desktop PC and standard 3D graphics card, make VR technology viable and attractive for mainstream training applications. The design, development, and implementation of interactive VR training systems is proposed as an innovative approach to augment safety training. However, in order to assess the impact of such VR training systems it is of particular importance to determine the effectiveness of the design of such systems. This article proposes an evaluation framework for this vital purpose. This framework comprises criteria to assess VR training systems, specifically relating to usability, instructional design, VR systems design, and mining industry context-specific aspects. Although the framework was developed as an evaluation tool to assess effectiveness of the design of such systems, it can equally well be used as a set of design principles to inform the design of VR training systems for mining. IntroductionMining in South Africa has been the main driving force behind the history and development of Africa’s richest and most advanced economy (Coka, 2012). The South African mining industry is frequently criticised for its poor safety record and high fatality rate (Stoddard and Skweyiya, 2016). Inadequate or insufficient training is often cited as a root cause of accidents (Van Wyk and De Villiers, 2009; Tichon and Burgess-Limerick, 2011). Virtual reality (VR) is a rapidly growing technology that utilizes the ever-increasing power of computing to simulate real-world and imaginary environments and situations with a high degree of realism and interaction (Webber-Youngman and Van Wyk, 2013). VR is currently being used or investigated as a training solution in a variety of industries. VR technology has developed rapidly and costs have fallen to levels where it can now be considered for mainstream training applications. The availability of 3D modelling tools and simulation programming engines that work effectively with a mid-range desktop PC and a standard 3D graphics card, make VR even more attractive to mine training centres (Van Wyk and De Villiers, 2009)."

May 1, 2019

By J. G. Walters

In 1928, the Coal Carbonization Section of the Federal Bureau of Mines, in cooperation with the American Gas Association, began a survey of the carbonizing properties of American coals. A standard test method for evaluating the carbonizing properties of coals that met the following conditions was developed: To yield products similar to those obtained in commercial operations. To produce yields sufficient to permit analyses and tests of quality. To be laboratory size. To be convenient to operate. To permit reproducible control of test conditions and results. This test method has become known as the Bureau of Mines-American Gas Association (BM-AGA) test (53),3/ and more coals of greater variety have been tested in this apparatus than in any other of similar scale.

Jan 1, 1961

By Ian Sheppard, Kugan Kuganathan

The Mount Isa Rocky Paste Fill (RPF) was one of the five fill options investigated for the Enterprise Mine filling between June 1996 and September 1996. Co-disposal of deslimed cemented tailings (CHF) and suitably graded rockfill (RF) in certain ratios produced the rocky paste fill. The RPF behaved like a cohesive paste with very high proportion of rockfill in the mix. Several large-scale mixing trials and drop tests proved that the rocky pastefill results in a homogeneous fill mass after placement. Segregation of RF was a common problem with MIM's traditional cemented rock fill (CRF), which is a combination of CHF and RF. The segregation was eliminated and a non-segregating paste like fill was created by optimising the particle size distribution of RF, and combining the RF and the CHF in optimum ratios. In rocky pastefill, the excess water in the cemented deslimed tailings slurry is taken up by the rockfill as the surface moisture on the rockfill particles and also as pore water between the particles. This results in thickening of the CHF, and the resultant mix is a non-segregating cohesive paste, which can easily spread to any horizontal distance inside a stope at a very low surface angle. The rocky pastefill releases no free water and relatively more pervious than the standard CHF due to rockfill component. With an average cement addition of 1.5 to 2% the rocky pastefill can develop higher strengths over 1Mpa. The rocky paste fill is applicable in many situations and can accommodate a variety of coarser materials that would be available in different mine sites. This paper present the research work and the experience associated with the rocky paste fill, and gives clear design principles for any potential users.

Jan 1, 2001

By Atta Ur Rehman, Kwame Awuah-Offei

This work evaluated the effect of bucket orientation and operating parameters on resistive forces and penetration for rubber tire loaders. The work used a 1:16 scale LHD model to test a rubber tire loader (RTL) bucket operating at different levels of tractive effort, speed, digging height, and rake angles in a full factorial design experiment. The work repeated the test on two different muck piles with different particle sizes and used generalized regression modeling to test the association of rake angle, tractive effort, speed, and digging height on penetration and resistive forces for RTL buckets. The results show that speed and tractive effort are more important in explaining RTL penetration and resistive forces than height above the floor and rake angle. Speed, tractive effort, and height above the floor are positively correlated to bucket penetration, whereas the rake angle is negatively correlated to penetration. Similarly, speed, tractive effort, rake angle, and height above the floor are all positively correlated to resistive forces incurred during initial penetration. The observation that the combined effect of speed and tractive effort is negatively correlated to penetration and resistive forces is a novel contribution that enhances our understanding of RTL loading. The results also show that the effect of speed, tractive effort, and height above the floor all change with changes in particle sizes. This work adds to the literature on the effect of rake angle, height above the floor, tractive effort, and speed on penetration and resistive forces for rubber tire loaders.

Aug 24, 2020

By D. W. Scott

Thermodynamics is a powerful tool for investigating rotational isomerism in substituted ethanes and related molecules. Accurate calorimetric data can be interpreted to give information, not only about the energy difference between conformations, but also about the shape of the potential barrier hindering rotation from one conformation to another. However, a deterrent to this use of thermodynamics is the labor required to calculate the contributions to the thermodynamic functions for assumed potential functions. Tables of thermo-dynamic contributions for appropriate potential functions can eliminate that labor and greatly facilitate the thermodynamic study of rotational isomerism. In this research, tables of contributions to the thermodynamic functions were compiled for two potential functions typical of some commonly encountered examples of rotational isomerism. TYPES OF POTENTIAL FUNCTIONS Potential function 1, illustrated in figure 1, A, has two equal minima higher than the third. It has the general shape of the barrier to internal rotation in n-butane, for example. The trans conformation of n-butane has the lowest energy, and the two skew or gauche conformations have equal but higher energy. Potential function2, illustrated in figure 1, B, has two equal minima lower than the third. It has the general shape of the barrier in 2-methylbutane, for example. The two C1 conformations of 2-methylbutane have equal energy much lower than the assumed Cs conformation, which has not been observed spectroscopically.

Jan 1, 1962

By R. W. Freedman

The gas chromatographic method, devised by the Bureau of Mines for analyzing routine mine air samples, was compared with the infrared method used for confirmatory determination of methane in mine air. While maintaining the specificity of the infrared method for methane determination, the gas chromatographic method is more precise, much more rapidly performed, and more convenient.

Jan 1, 1968

The complete life cycle of a production facility has many phases requiring many different skills and many different personalities. It is not unlike the life cycle of a person and many parallels can be drawn from it. I leave some of these analogous situations to your fertile minds. The author, having worked in operations, plant design, plant commissioning, marketing and many other interesting situations through the industry has drawn from this experience and examples given by many associates in the industry.The phases seen are as follows: Concept Studies û someone has a bright idea of how to make a dollar. Scope Studies û what possible processes/options that could make a dollar. Prefeasibility Study û the æviableÆ scope options are studied to develop feasible options. Feasibility study û defines the concepts that should be designed to make a viable project thus enabling financing and project commitment to be made. Detailed Design û an intermediate step that consolidates the inputs to give a robust plant that can be constructed.Construction û people can see what they thought was going to occur and start to understand the plant. Commissioning û the hand-over of æownershipÆ from the conceiverÆs to the operators. Operations û the ætoyÆ has become reality and money must be made. De-commissioning û the plant has seen out the useful life of the ore deposit, it now goes through a further process required by society.Across these phases of plant design run several countervailing management requirements that can influence the outcome of the plant design. Some of the management rigours that have to be applied to the various phases are as follows: costing basis of the various phases; operational and maintenance reviews; sustainable development; risk assessment; reliability reviews; equipment availability; commissioning time; and environmental review.This paper endeavours to awaken people to the phases that projects require for a successful outcome and the management rigour that has to be applied throughout the phases to ensure the correct intellectual horsepower is applied at the right time to ensure the best outcome.Many of you would be parents and realise this is not unlike the development of children, teenagers, adults, retirees and ongoing.

Jan 1, 2002

A numerical model of the spontaneous combustion of coal has been developed and is being used to investigate the nature of self-heating in underground coal mines. Results to date confirm the complexity of the self-heating reaction in coal and illustrate the impact of the factors such as the coal reactivity, mass and airflow through the coal pile. Subtle differences in the chemical, physical and environmental conditions and make a significant difference in the development of a high temperature self-heating or a low temperature benign condition, the subtlety escaping normal underground observations. Additional work is planned to investigate the thresholds for such factors in the development of spontaneous combustion and it the implications for detection by gaseous Products.

Jan 1, 1998

By G. Diaz

Técnicas Reunidas (TR) has been involved for over 30 years in the development of process technologies for the recovery of zinc from different primary and secondary feed materials, such as the ZINCEXTM process. Because of the complexity of the feed mineral resources, solvent extraction (SX) is an invaluable technique to concentrate and purify zinc solutions. When applied to a pregnant leach solution, solvent extraction can produce an extremely high quality zinc electrolyte, suitable for obtaining SHG zinc ingots, after electrowinning and melting and casting processes. However, the high affinity of most organic extractants for Fe(III) poses a serious problem, which may adversely affect the zinc extraction process. Different methods may be applied to deal with the negative effect caused by Fe(III). An acid regeneration step and electro-reduction stripping have been considered as the most viable techniques to remove the iron from the organic phase. This paper describes some findings of Técnicas Reunidas in the area of zinc solvent extraction, especially on removing Fe(III) from the organic phase.

Jan 1, 2006

By K. Anim, C. Calderon-Arteaga

Located in Mojave, CA, The Soledad Mountain mine is an Open pit Heap-Leach gold Mine, which is operated by Golden Queen Mining Company LLC. under private capital. Open pit mining began in 2015 while full production was reached in 2016. The open pit mine feed a processing plant that can process more than 13K tons per day of ore which is sent to a heap leach pad. The Soledad Mountain project is a poly metallic deposit with Au and AG being recovered as payable metals. As the mine became bigger after moving to the east pit phases, Golden Queen was facing new challenges to control the production and accurately determine KPIs to improve/increase the production. To maximize returns and asset value, a new fleet management system (FMS) was adopted and implemented. The new FMS has enabled the mine to interconnect the different stages of the mining, as well as to recognize issues and implement the necessary corrections. With the associated increase in complexity in the process, the requirement of the ore control system to accurately predict ore feed characteristics is critical to maximizing metal recovery. Implementation of new daily and weekly plans were needed to ensure the ore delivery and meeting the tonnage goals, while allowed the equipment operators to better geolocate and to maximize the equipment production. These conditions alongside with Golden Queen’s drive to increase profitability and maximize net asset value has created challenges. These challenges are numerous and multifaceted. However, the ability to accurately route the material from the mine, is critical to site success and some of these challenges have been overcome by the adoption of the new FMS, the implementation of daily and weekly plans and upgrades in the ore control workflow. Examples of how the integration of the new systems allowed golden Queen to improve production strategy, are discussed in this article.

Mar 2, 2022

By Jorge Blázquez, Paulo Couceiro, Patricio Vergara, Luis Martínez, Juan Navarro

This study introduces the X-2Mill solution, a refined two-step methodology aimed at optimizing blast designs by aligning explosive energy with rock properties. The approach employs the X-4Traits Model, which uses drill-monitoring data from both autonomous and manual drilling modes to develop two critical indexes: the Drilling Rock Factor (DRF) and the Drilling SAG Power Index (DSPI). The DRF integrates the Size-Energy Fan Model with rock fragmentation results and blast design parameters, while the DSPI adjusts Specific SAG Energy (SESAG) based on Bond’s theory, incorporating ore X80 results, SAG mill capacity (TPH), and power draw to estimate milling difficulty. To enhance prediction accuracy, the X-2Mill solution incorporates, to a Principal Component Analysis of the normalized drilling data, a Meta Machine Learning model with a 3D spatial function, accounting for information from surrounding drill holes. This integration improves the precision of the DRF and DSPI estimates. The methodology unfolds in two main steps: Step 1: Bench-Scale Pattern Design, involves defining the target P80 size for ore based on the SESAG and the DSPI. It also establishes target X80 sizes for waste and oxide materials and iterates to determine the optimal Burden x Spacing (BxS) using the Size-Energy Fan Model and the DRF. Step 2: Blast-Scale Selective Explosive Density/Energy focuses on refining explosive density on a hole-by-hole basis to achieve the specified X80 values for ore, waste, and oxide materials. The X-2Mill Solution was developed at Minera Escondida Limitada (MEL) using data from 162,761 blastholes across 356 blasts conducted over three mine expansions. This solution addresses the challenges of blasting harder and more difficult rock, particularly in the lower levels of the mine. By adapting the blast pattern and explosive density to the specific rock properties and ore/waste designation, the X-2Mill Solution aims to achieve precise size distributions and improve overall blasting performance. The results demonstrate that the X-2Mill Solution balances ore fragmentation to meet SAG mill throughput requirements while optimizing powder factor costs for waste material and maintaining digging efficiency. By efficiently distributing explosive energy, the solution not only enhances throughput but also improves blasting efficiency while ensuring stable slopes and minimizing fault activation.

Jan 21, 2025

By B Nielsen, H Lehto, B Musuku

"The demand for fine and ultra-fine grinding associated with the processing of more challenging, finer grained orebodies and the global driver of minimising energy consumption has been an increased focus in our industry. Outotec’s stirred milling technology, the high intensity grinding mill (HIGmill™), was launched in 2012 in response to this industry need. First Quantum Minerals Ltd selected HIGmill™ technology for its Kevitsa mine in Northern Finland. The 700 kW mill is grinding copper rougher concentrate to improve copper/nickel separation and copper recovery. Selection of the HIGmill™ followed mineralogy analysis and laboratory and pilot testing for HIG milling in parallel with flotation tests to determine optimum grind size and energy input.The paper discusses the challenges and successes of the test work, manufacture, installation, commissioning and subsequent operation of the mill. Grinding performance is presented and a comparison between predicted and operating energy efficiency is made. In addition, the various steps to optimise wear rate and minimise maintenance and downtime are made, with particular reference to internal geometry of the mill.Citation:Nielsen, B, Lehto, H and Musuku, B, 2016. Design, Installation, Commissioning and Operation of Fine Grinding Technology at the Kevitsa Mine, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 59–66 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By S. Fahland, P. Vogel

"The Gorleben salt dome has been investigated since 1979 for its suitability as a repository for the disposal of high-level radioactive wastes. The geoscientific surface exploration was followed by underground exploration of the site beginning in 1983: underground excavation work included the sinking of two shafts from 1986 to 1994, the excavation of the infrastructure area and of drifts located in the first exploration area EB1 within the following years. The exploration was interrupted for ten years from 2000 to 2010 as part of a moratorium. After the expiry of the moratorium in March 2010, the geoscientific underground exploration at the Gorleben site was resumed. The investigations were interrupted again in autumn 2012 due to a political decision. The exploration programme included extensive geoscientific investigations: geological exploration, geophysical investigations, mining exploration and mining observation, laboratory tests, in-situ geotechnical measurements, geological modelling and numerical model calculations. To analyse and interpret the results of the in-situ measurements and mining observation geomechanical, thermal and thermo-mechanical model calculations were carried out. One of the main elements of the in-situ geotechnical investigations were high-resolution geothermal measurements performed in boreholes used for geological exploration and geotechnical tests.The geothermal measurements are used to evaluate several geotechnical findings, e. g. drift closure, rock deformation, stress change, and are completed by thermal model calculations to analyse and interpret the results of in-situ measurements and mining observation. The model calculations have been carried out using the special purpose JIFE code. To consider the whole exploration mine with the adjoining host rock as well as the successive excavation of drifts and boreholes in detail a three-dimensional finite-element model was developed. The model calculations are used to analyse the cooling-off of the surrounding rock of the drifts caused by ventilation. The cooling-off of the surrounding rock is an ongoing process affecting the results of further geotechnical measurements in the near field of the drifts. To predict a realistic time and space dependent distribution of the temperature field of the host rock within the exploration area which is influenced by ventilation thermal model calculations are necessary. Comparing the calculated temperature field with the in-situ determined rock mass temperature field within the exploration area EB 1 the results show a sufficient agreement. Furthermore there is very good correspondence, both qualitatively and quantitatively, between the experimental and the calculated findings regarding the temperature profiles including the effects of excavation and ventilation of the drifts."

Jan 1, 2015