Search Documents

By A. Alfantazi, E. Asselin

"The corrosion of commercially pure titanium (CP-Ti) was studied from room temperature up to medium temperature (~160°C) under conditions relevant to medium temperature chalcopyrite leaching processes. The corrosion rates were measured by immersion and electrochemical tests in sulfuric acid. The influences of chloride, cupric and ferric ions on the corrosion rate and behavior were also investigated. Corrosion of the CP-Ti did not account for the total current density measured by linear polarization tests. The corrosion rates of CP-Ti under medium temperature leaching conditions were surprisingly high. The corrosion rate measured in ferric containing solution at 160°C was approximately 20 mm/yr.INTRODUCTIONTitanium exhibits excellent corrosion resistance in many aggressive environments because of the formation of a very chemically stable, highly adherent, and protective oxide film on its surface (Mitsuo et al., 2002). Because titanium is the only metal available at a reasonable cost that resists the high temperature corrosive slurries in many leaching processes, it is often chosen as autoclave liner material where it is subjected to severe conditions of acidity, temperature and pressure (Grauman and Say, 2000).A number of distinctly different hydrometallurgical processes for the pressure leaching of chalcopyrite have been developed and patented by various companies and they can be classified into low, medium and high temperature regimes (McDonald and Muir, 2007). For example, chalcopyrite concentrate may be processed at medium temperatures (115-175°C) and pressures of 800-2200 kPa (Dreisinger, D., 2006; Sahu and Asselin, 2011). The lixiviant may contain 20 to 55 g/L sulfuric acid, 8 to 12 g/L chloride ions, 10-25 g/L Cu2+ (Jones, 1995, 1997, 1999), and less than 1 g/L Fe3+ (Defreyne et al., 2005). The amount of these additions is determined by the grade of the ores and details are shown in Table 1."

Jan 1, 2012

AVERY great profit is derived from removing the gilding and retrieving gold, without destroying the works of silver or other metal. If this method did not exist, the greater part of the gold that is put on certain works would be lost. Even though you might think to scrape it off patiently with a sharp scraper, if it had been drawn with draw-plates, or if it were at the bottom of objects where the scraper could not enter easily, it would be utterly in vain. Therefore, I find that to do this it is necessary to use one of three methods. The first is when it is found on a thin object. Take a large crucible, fill it with mercury, and heat it on a little furnace. When you see that it begins to boil and simmer, put your work in it and stir it around, shaking and rubbing it well in this, and finally rub it with a scratching tool until you see that the mercury has drunk up and absorbed all the gold. Then, having done this, take the said mercury and pass it through an untanned leather purse, and in the bottom of this you will find all the gold like sand. Put this in the bottom of a crucible or in something else over a charcoal fire and evaporate it. If the objects are of a thicker form the gilding is removed from them in another way, by covering them with powdered sulphur and lighting a fire on them. When you see them burning well with the fire all around, beat them in a clean bowl of wood or something else and collect everything that separates with the sulphur from the work; this will be gold in the form of a leaf wherever it has been touched by the fire. The gold is then extracted from this burned sulphur by purifying it in a cupeling hearth with lead. The third method is to touch the gold that you wish to take off the works with an aqua fortis made from saltpeter, rock alum, vitriol, sal ammoniac, and some verdigris.* This acid dissolves and eats the gold by virtue of its corrosive power. Having thus touched the gold with this acid and having saturated the latter with a quantity of gold, put it in a cucurbit and evaporate it over a little furnace as is done with silver, collecting the acid and the spirits if you wish.

Jan 1, 1942

Increasing demands on quality of metallurgical grade alumina and for lower production costs led to the development of a new fluid bed calcining process. The process, jointly developed in Germany by Vereinigte Aluminium Werke A. G. and Lurgi Gesellschaften m.b.H., takes advantage of modern chemical engineering methods such as counter-current flow of combustion air and solids, direct heat-exchange between combustion air and fine solids, and near stoichiometric combustion of oil in a fluid bed. Using a two-stage Venturi-type suspension preheater for heat-recovery from combustion flue-gases, the circulating fluid bed technique with internal oil combustion at 220°F for the calcining step and a five-stage fluidized bed cooler for heat-recovery from calcines, the process gives an outstanding heat-efficiency. In a first industrial plant for 560 sh. tons/day of alumina heat consumption figures of less than 1·400 B.T.U./lb Al203 g were achieved.

Jan 1, 1972

By C. Chamberlain

The mining industry continues to underpin the regional economy. Australia, benefiting from a weak currency, receives 27% of the total goods export value from non-energy mining lead by aluminium, iron ore, gold and nickel. Consolidation has eliminated CRA, Comalco, North, Savage, Acacia, Ashton, Great Central, Aberfoyle, Placer Pacific, Plutonic, Normandy and RGC leaving Rio Tinto, BHP-Billiton, WMC, MIM and, increasingly, the South African companies Anglo, Gold Fields and Harmony as dominant players. Exploration stagnates with expenditure dropping 40% in Australia and 80% in PNG from peak levels. Major new regional developments include Rio’s West Angles iron ore project, Newcrest’s Ridgeway gold-copper mine and Inco’s Goro nickel-cobalt project in New Caledonia.

Jan 1, 2002

At the end of a century of mining education in South Africa, it is appropriate to reflect on the past, take stock of the present and ponder the future of mining education. While it is likely that changes in the mining industry will generate an increased demand for mining graduates, the number of suitably qualified applicants to study mining is worryingly small. While good progress has been made in unifying the educational system that previously provided schooling on a racially separate basis, it appears that a decade or more will be required to raise competency levels in mathematics, science and English, and this paper describes the process as it affects mining engineering programs. It also describes the initiatives currently being undertaken by the University of the Witwatersrand and the mining industry to ensure that the South African industry receives an adequate flow of well-qualified mining graduates, despite more than 70% of the intake coming from severely disadvantaged educational backgrounds.

Jan 1, 1999

By A J. Eggers

With gold first discovered at Carrick in 1864, exploration and mining on the Carrick Goldfield in Central Otago, New Zealand, has now been ongoing for more than 130 years. Recorded historical hard rock production from up to 52 different mining claims from 1864 to about 1921 is 24,047 ounces (oz) of gold.   Since 1980 Amoco Minerals New Zealand Limited, CRA Exploration Pty. Limited, Amax Gold Mines New Zealand Limited and Summit Gold (New Zealand) Limited have conducted modem systematic exploration campaigns targeted at locating shear controlled gold bearing quartz lodes and stockwork deposits. More than NZ $1million has been spent by these companies on aerial photography, geological mapping, stream sediment surveys, soil and rock chip geochemistry as well as reverse circulation (RC) percussion and diamond drilling.   RC drilling by Summit Resources in 1997 has identified a 1,500 m long zone of low-grade gold mineralisation at Lower Carrick, with an average grade of 1.00 g/t Au over a 14 m average thickness. This gold mineralisation, hosted within a low angle shear zone, has analogies with the Hyde-Macraes Shear Zone in eastern Otago. Recent exploration and drilling at Carrick has revealed the potential to discover large (>0.5 million ounce (Moz)) low-grade bulk shear controlled quartz vein and stockwork gold deposits similar to those now being mined at Macraes.

Jan 1, 1997

In the context of sustainable development, the Minerals Council of Australia (2010) states that 'investments in minerals projects should be financially profitable, technically appropriate, environmentally sound and socially responsible'. In other words, the business of mining can only be sustained if these criteria are met.   Science and technology plays a major role in all four of these criteria. This paper will present the technology and innovation emerging from the Minerals Down Under National Research Flagship which brings together CSIRO and more than ten of Australia's leading universities to work with industry to drive efficiency, productivity and environmental performance. This work is required if the Australian minerals sector is to thrive and continue to deliver national benefit in the face of increased global competition, declining ore grades, depleting ore deposits, increasingly constrained national resources (land, energy, water and people) and changing societal expectations.   Science and technology to reduce emissions and water use, discover greenfields resources, enable deeper mining operations and transform mineral processing are described. Technology is presented as an enabler of sustainability: a means to this end but not as an end in its own right.

Jun 1, 2010

A summary of a proposal to develop a 20 000 tpa underground gold operation in a Forest Park. The environmental constraints are severe and affected the mine development planning and choice of mining method. The mine will use trackless methods to access the narrow 1.5 m ore shoots, and to mine ore by cut and fill methods. The use of Microscoop and CT 1700 HE electric LHDs for mucking, together with special drilling attachments for drilling, is central to efficiency and small Kubota diesel haulers will be used for carrying ore to surface.

Jan 1, 1986

By V. M. S. R. Murthy, Biswaraj Dash, Somnath Chattopadhyaya

Tunnel boring machine (TBM) has been in focus for the last few decades and is currently the most preferred excavation method for metro, hydro and irrigation tunnels. Tunnelling in hard and abrasive rock conditions, in particular, is adversely affected by a very low advance rate coupled with increased TBM disc cutter failures and cutterhead jamming, seeking an in-depth understanding of the design and operational processes of the boring components of the TBM. The cutterhead and disc cutter are the critical boring components of the machine, influencing the boring process significantly. These components directly interact with the rock and hugely influence the machine’s efficiency. This paper encapsulates a review of prior studies related to disc cutter design and the cutterhead design for hard rock TBM tunnelling. A design methodology for designing and selecting a disc cutter and a cutterhead is suggested. The design methodology has been applied for a hard rock tunnelling case, and suitable design specifications for the boring components were arrived at. The disc cutter and cutterhead specifications designed based on the suggested methodology closely match with that of deployed TBM specifications. It may be observed that except for the case of high-strength and high-abrasive rock (greyish quartzite), for the rest of the rocks, the suggested design can meet the desired advance rates.

Jan 31, 2024

By D J. Brake

The importance of mine ventilation to health and safety in both coal and metalliferous mines has been long recognised. The primary and secondary ventilation systems in most metalliferous mines incur 50 per cent or more of the total mine electrical power consumption and frequently about 10 per cent of total underground mine operating costs. The requirements for ventilation-related horizontal and vertical development, fans and cooling have a significant impact on mine capital costs and also on mine schedules and start-up times and hence cash flows. There are increasing pressures on regulators and miners to reduce airborne contaminants such as diesel particulatematter, nitrogen dioxide and heat (wet bulb temperatures), and significant pressures to reducegreenhouse gases such as fugitive methane emissions from coalmines and the carbon dioxide footprint of both coal and metalliferous mines. Many previously Australian miners are now globaloperators and have extensive overseas mining operations where local ventilation standards and expertise may not be consistent with Australian practices. The role of the site ventilation officer is also changing with strict new requirements for the statutory position being introduced into Queensland metalliferous mines and the potential for this to become more widespread. Recent regulator and parliamentary review committees have identified systematic shortcomings in mine ventilation compliance, and statutory certificates in both Queensland and NSW now require continuing professional development to maintain currency. Public and investor support for mining are also increasingly contingent on safe, healthy and environmentally responsible practices and the standards for these are frequently tightening. Good ventilation design and operating practices that are consistently well executed therefore contribute significantly not only to a safe and healthy mine but also to a productive and cost-effective operation and the ongoing social licence to operate. There are a variety of ways of providing technical design and oversight into a mine’s ventilation systems; this paper explores some current trends in ventilation standards and statutory requirements, as well as ways to support and develop mine ventilation staff for both domestic and international operations and also the emerging senior technical roles of Group/Principal/Corporate mine ventilation engineer.

Oct 12, 2022

By F. J. Alcock

The Appalachian region of Canada comprises the three maritime provinces; Nova Scotia; New Brunswick; and Prince Edward Island; and that; part of the Province of Quebec lying south and east of Logan's fault. This; major thrust runs in a gently curving line from lake Champlain to Quebec; city and thence down the valley of the St. Lawrence to pass between Anticosti; island and Gaspe peninsula. To the northwest lies the St. Lawrence; Lowland division of the Interior Plains geological province; a region underlain; largely by early Palxozoic strata; which for the most part lie horizontal; or with low dips; where faults occur they are predominantly of the normal; type; and only locally are the beds cut by intrusive rocks. To the southeast; on the other side of the fault zone; an entirely different set of conditions is; encountered. There; Lower Devonian and older strata stand at high angles; are sheared and thrust faulted; and are intruded in many places by granitic; igneous bodies. The present paper is designed to outline briefly the geological; and structural history of this geological province and to emphasize; the part that structural conditions have played in connection with mineral; deposition.

Jan 1, 1954

Jan 1, 1996

By W. G. Pariseau

Reliable stress measurement using hollow inclusion gauges and monitoring stress change using borehole stress meters and borehole deformation gauges in anisotropic rock remains a challenge for the rock mechanics community. In this regard, the complex variable method advanced in 1983 for deducing stress in anisotropic rock is flawed and software is privileged. Fortunately, advances in computer hardware and software now enable fast, reliable reduction of hollow inclusion stress measurement data for determining stress in anisotropic rock. Monitoring stress change in anisotropic rock poses a different challenge but is also subject to numerical analysis. Stress measurement using a hollow inclusion (HI) gauge such as the triaxial Australian HI is done in four steps: 1) drilling a measurement hole, 2) installation of an HI, 3) stress relief of the HI by overcoring, and 4) data reduction. The last step, data reduction, is the focus of this work. The process is well-known in linearly elastic, isotropic rock (Worotniki and Walton 1976, Duncan Fama and Pender 1980). However, in case of linearly elastic, anisotropic rock the requisite technology is not readily available. This situation is somewhat surprising because anisotropy is more often the rule rather than the exception, especially in the neighborhood of ore bodies. Rahn (1984) has pointed out the potential for significant errors with neglect of anisotropy and the adverse consequences for engineering design. Amadei (1984) has also pointed out the potential for errors with neglect of anisotropic rock properties in stress measurement. Worotniki (1993) cites other studies that indicate potential for serious errors when doing measurements in anisotropic rock. In both theoretical cases (isotropy and anisotropy), data reduction is essentially a composite of solutions to boundary value problems in linear elasticity. In the finite element approach, the analysis is a simulation of gauge hole drilling, installation and overcoring. Two important advantages with the finite element approach are a more faithful representation of the conditions of HI stress measurement than approximated in theory and the capability for handling rock whether isotropic, transversely isotropic or fully anisotropic

Mar 2, 2022

By A. L. Moore

KAISER Bauxite Co., a subsidiary of Kaiser Aluminum & Chemical Corp., has been mining and shipping Jamaican bauxite for over a year. On Feb. 10, 1953 the first boat load of bauxite left Port Kaiser, Jamaica, for the company's alumina plant at Baton Rouge, La. To provide its own source of the aluminum ore, a Kaiser Aluminum & Chemical Corp. exploration party started initial reconnaissance in 1947. This work, and subsequent exploration, led to the acquisition of reserves sufficient to warrant a full-scale mining operation for several decades.

Jan 3, 1954

The Cuajone and Toquepala copper projects are located in the extreme southern area of Peru. Since 1960, Southern Peru Copper Company has operated the Toquepala open -pit mine, flotation mill, 110 smelter, townsites, power plants, and railroad. Toquepala and 10, the smelter and port location, are connected by a 110-mile-long (176 lun) railroad. Much of Toquepala's infrastructure has been used for the Cuajone project. Cuajone, at an elevation of 11,400 ft (3475 m), required five standard-guage railroad tunnels with a combined length of 17 miles (27.2 km) to connect with Toquepala so concentrates could be shipped to the no smelter. The total cost of Cuajone is estimated at $726 million for a designed annual capacity of 180,000 tons of copper, equivalent to about $4,000 per ton of installed production capacity. This relatively low cost per ton, by today's standards, has been made possible through the use of the 110-to Toquepala railroad, the ability to expand the 110 copper smelter, and other favorable factors. To mine the 468 million tons of copper sulfide or e at a grade of 1.0% copper, approximately 24 1 million tons of waste were stripped- before mining of ore to supply the new Botiflaca 45, 000 ton per day concentrator. The mining rate must exceed 300,000 tons of waste plus ore per day to maintain the 45, 0 00 tpd sulfide ore milling rate which was to be reached at the end of 1976. Waste stripping is done with 15 cu yd electric shovels and 120 -ton trucks. Ore mining is done with 8 and 9 yd shovels. A railroad connects the pit with the 60 in. by 89 in. Allis-Chalmers gyratory crusher. Side-dump railroad cars of 50.cu yd capacity dump onto a 0 16 ft 9 in. long (5. 1 m) grizzly inclined at 40º with 7 to 8 in. (178 to 203 rnrn) bar spacings. The grizzly is divided into two 22 ft 4 in. (6.8 m) wide sections and two side -dump railroad cars discharge simultaneously into the 150-ton capacity dump pocket. A Barco rock manipulator is used for breaking or removing oversize from the dump pocket. The bin receiving the grizzly undersize has a capacity of 5,000 tons, and the pocket beneath the crusher holds 900 tons. Each is equipped with an 84 in. apron feeder, which feeds a 60 in. (1.52 m) conveyor belt to the 150,000 ton coarse ore stockpile, where the ore is distributed by a 72 in. (1. 83 m) tripper conveyor. The 45, 000 live tons in the coarse ore stockpile are reclaimed by twelve 48 in. (1. 22 m) apron feeders. Maintenance on the crusher eccentric is made easy by an eccentric

Jan 1, 1978

By M. Zaske, E. R. Mortensen

"As mine operators continuously look for ways to improve functionality and increase the capacity of their facilities, existing process equipment is often pushed to and past its designed limitations. As a result, equipment manufacturers are asked for economical solutions to meet redefined processing needs. Newmont Mining in Nevada was faced with such a need in its carbon-in-leach (CIL) train. In a collaborative effort between Newmont and Derrick Corp., tests were conceived to assess the viability of drop-in replacement screens using a three-dimensional screen panel. The synthetic pyramid screen panel was designed to increase flux while maintaining the existing equipment footprint. The test is the end result of an ongoing research and development project that Derrick undertook in an effort to refine and upgrade its urethane screening media. The application of this new screening media is presented for this CIL application along with future plans to implement the technology in trash, safety, carbon dewatering, carbon sizing and other scalping applications.In spring 2014, Process Machinery Associates (PMA), Derrick’s local area representative, met with Newmont to discuss the operation of the in tank screens in the CIL train at Twin Creeks, near Golconda, NV. The process was originally designed for about 12+ kt/d (13,000+ stpd) but the throughput has been steadily rising since the plant was commissioned. Newmont now requires 14.5 kt/d (16,000 stpd) to be processed. The original screens were running at their maximum capacity, and Newmont required additional screening capacity to continue the upward trend in production.Physical separation by use of screening is one of mineral processing’s oldest methods. Screening media can be prone to blinding and pegging, and the necessary support structures required for finer apertures result in smaller open areas. Therefore, more screening area generally requires larger panels and, thus, larger machines, screening media that does not blind or a combination of both.In an effort to avoid larger machines, Derrick had been working on a revolutionary threedimensional panel that would add nonblinding screen area in the same footprint of an existing machine. Alpha testing of the new screen panels began at Newmont Mill 2/5 in July of 2013. It was still occurring when PMA approached Twin Creeks about beta testing a refined machine and pyramid panel. After presenting the initial results, Twin Creeks determined that an upgraded machine and pyramid panels would be a possible solution to meet production needs. The testing of a machine eliminated the risk of capital costs to Newmont and provided Derrick the opportunity to obtain additional data."

Jan 1, 2015

By Ting Lu, Gerard Laman

"This document compares the systems of coal classification described under ASTM standards used in Canada to GB standards used in China. A preliminary connection of metallurgical coal classes was set up between the two classifications. In GB classification system, there are nine metallurgical coal groups, namely PS, SM, JM, FM, ½ ZN, RN, 1/3 JM, and QM used in coal blending for coke production. PS coal is almost equivalent to the Low Volatile Bituminous coal; SM, JM, and FM coal groups fall into Low to Medium Volatile Bituminous range; ½ ZN, RN, 1/3 JM, and QM are equivalent to bituminous coal with medium to high volatile matters; QF contains higher volatile bituminous coal compared with High Volatile Bituminous coal. The caking properties commonly used in respective country are also compared in this document. These properties include free swelling index (FSI) and maximum fluidity used in Canada, as well as caking index (GR.I.), and the maximum plastic layer thickness (Y) mainly employed in China. It has been observed that the log of the maximum fluidity has a stronger correlation with the caking index than the Y values. Metallurgical coal processing strategy and typical coking coal product qualities are briefly discussed in the last section of this paper. Currently there is a trend to use heavy medium cyclone in both countries. In Canada the conventional two-product cyclone technology is the preferred practice; whereas in China the three-product heavy medium cyclone arrangement is widely used.INTRODUCTION Coal can be simply classified by applications into two categories: i) thermal coal used to provide heat energy in combustion, and ii) metallurgical coal which is converted to coke, in a carbonization process, and used mainly in the iron and steel industry. Metallurgical coal contains even higher heating values than thermal coal. In addition, it presents unique plastic properties during carbonization which in turn produces a porous solid, high in carbon referred to as coke. Coke is one of the most important raw materials in the iron and steel industry."

Jan 1, 2012

By Anderson Meireles, Leonardo Soares Chaves, Raul Carretero Hoz, Carlos Eduardo Soares Feliciano, Renato Jacome Costa

The large iron deposits in the northern region of Brazil located in the Amazon Craton have in common the presence of natural cavities. These cavities primarily occur in the upper layer of the ore body, formed above hematite mineralization. Their origin remains a topic of debate, often associated with hydrothermal drainage processes and erosive evolution. Over time, these cavities have become integral to the local environment, each contributing to the regional ecosystem of fauna, flora, and the significance of speleothems found within them. Managing these cavities poses a significant challenge for iron mines in the area. On one hand, they must preserve the cavities from anthropogenic actions, while simultaneously handling heavy equipment and large volumes. In 2023, the development of the mine took place towards the cavity under study, revealing systematic deviations in vibrations recorded during nearby detonations as the blasting got nearer. To address this, a work plan was put in place, emphasizing a straightforward approach: constructing lithology-specific vibration models, defining charge abacuses, and optimizing timing to reduce charge amplification. Implementing this methodology significantly improved adherence to the vibration limit, resulting in an around 50% reduction in standard error. This paper presents the consolidated work that allowed mining activities to continue in the area through controlled blasting, effectively mitigating potential anthropogenic damage in sensitive areas.

Jan 21, 2025

Industries in the Kwinana area have embarked on a journey of improving the eco-efficiency of Western AustraliaÆs primary heavy industry area. The Kwinana Industrial Area has some unique characteristics that provide both opportunities and barriers. The Kwinana Industries Council and the Chamber of Commerce and Industry are working with the industries to identify a range of projects that can deliver improvements for both environmental and economic æbottom linesÆ, and to progress these projects using internal and external resources. The evolution of the process, its relationship to the ethos of operating companies, and the availability of resources to pursue projects, is an interesting study with lessons for others interested in taking the same course.

Jan 1, 2002

By Blanchard R

In stopes of the 2000- and 2150-ft. levels in the North mine section of North Broken Hill Limited, whence a substantial proportion of the company's production is being drawn, and especially in stopes which involve the portion known as the Northern orebody, occurs it light-coloured friable porous material which represents average grade ore from which the lead and zinc minerals, and certain gangue constituents, have been largely or wholly removed by leaching. The 2000- and 2150-ft. levels lie, respectively, 1550 and 1700 ft. below extreme base of the pre-mine oxidized zone. Composition of the cellular product shows it to be supergene. The oxidation and leaching, therefore, must be assumed to have taken place since drainage of the affected areas was accomplished by mining operations.The matter is of more than passing interest, because the post-mine...

Jan 1, 1942