Search Documents

By Paul Hosford, Tim Haldane

"The paper describes the fast-track development of the project from feasibility study through to detailed design and construction, highlighting the process adaptations for handling sticky ore and water management in a tropical environment, and subsequent commissioning and operating experience of the mine. The paper discusses the geological setting, the environmental and socioeconomic considerations in developing and operating a mining operation in an underdeveloped country and the logistical challenges involved in bringing a large capital investment into Central America.INTRODUCTIONGlamis Gold Ltd. acquired the San Martin project in Honduras as a result of its merger with Mar-West Resources in late 1998. Despite the prevailing low gold price environment at the time of acquisition, Glamis anticipated rapid development of the San Martin project due to the quality of the deposit and other positive factors.Following favorable exploration and permitting activities in the first half of 1999, Glamis prepared a Feasibility study. In October 1999, Glamis decided to proceed with the development of the project and selected Hatch to provide the engineering, procurement and construction management services for the project. The San Martin project was in full-scale commercial operation approximately 14 months after the receipt of Board approval, and by July 2001 the San Martin project was operating at approximately 150% of its feasibility design capacity."

Jan 1, 2002

By V. Mathebula

Paper written on project work carried out in partial fulfilment of B. Tech (Mining Engineering) degree The purpose of this study is to establish whether to mine the Bottom of Pit (BOP)/TOB 4 reserve before the commencement of the Block Cave or whether this should be disregarded and the reserve be extracted at the end of the life of the Cave. The primary goal of this report is to investigate and propose a practical mining method to safely extract the reserve given the set constraints. This report quantifies the additional revenue the TOB 4 will contribute to Finsch?s overall NPV thus enhancing Finsch?s business case and strategically enhancing the SBP. Several underground mining options have been investigated. The proposed mining method includes the installation of a series of extraction tunnels below the TOB 4 reserve from 53 level, with a slot access tunnel system. Ground will be loaded by LHDs from the draw points and tipped into 50-ton dump trucks at a transfer point, from there the ground will be transported to 53 level No. 1groundpass where it will join the existing ground-handling system. Primary development is scheduled to begin October 2002 and last for a period of approximately 7 months until early April 2003.The production is broken into 4 phases. Phase 1 is scheduled to begin mid-April 2003. The final production phase will be completed by November 2005. The production scheduling has been designed in order to remain ahead of the Block 4 undercut in order to ensure stability and safety. Due cognisance was taken of the health and safety of all employees concerned during the design of the mining and ground-handling processes for the Bottom of Pit. As far as is reasonably practicable, the BOP was designed and will be constructed and equipped to provide conditions for the safe operation of machinery and a healthy working environment for people underground. Relevant requirements of the Mine Health and Safety Act regulations pertaining to mining operations have been identified and adhered to during all phases of the design process.

Jan 1, 2004

By George A. Morrison

This paper describing the methods of mining and crushing limestone at the West Winfield, Pa., limestone mine of the West Penn Cement Co., is one of a series being prepared by the Bureau of Mines on mining practices, methods, and coats in the various nonmetallic mining districts. HISTORY The limestone deposits of western Pennsylvania have been exploited for many years and have been quarried extensively at West Winfield in Winfield. Township, which lies in the southeastern corner of Butler County.

Jan 1, 1931

By Rita Aiello, Stan Mack, Peter Werth, Joseph McCarney, Jozef Stachulak

"Johnson Matthey has developed the first diesel particulate filter (DPF) for underground mining that controls particulate matter (PM) at the same time as maintaining emissions of NO2 at or below engine baseline levels. DPF technology is critical for controlling PM which is classified as a carcinogen, but passively regenerating systems rely on the use of oxidation catalysts that can potentially increase NO2 emissions. This paper reviews the development of low-NO2 PM control technology and the results from testing this technology underground on diesel mining equipment. KEYWORDS Decomposition catalyst, Diesel particulate filter (DPF), Diesel particulate matter, Mining Continuously Regenerating Trap (CRT®), NO2, SCR INTRODUCTION The introduction of diesel particulate filter (DPF) technology on heavy duty diesel (HDD) engines has been an important step towards addressing the clean air and health concerns for mining companies. Control of diesel particulate matter (PM) emitted from diesel engines is already being implemented for on- and off-road vehicles, and similar legislation is being prepared for mining equipment. In addition to PM, the diesel emission control strategies (DECS) also reduce carbon monoxide (CO) and hydrocarbons (HC). Some DECS control oxides of nitrogen, or NOx, which is composed of NO and NO2. Johnson Matthey has led the development of emission control technologies for diesel engines for almost 30 years. Over the last ten years alone JM has supplied over 3 million Continuously Regenerating Trap (CRT®) DPF systems for on-road vehicles, and over 200,000 systems for off-road vehicles. The patented CRT technology combines a diesel oxidation catalyst (DOC) with a DPF to effectively trap harmful PM from diesel exhaust, while removing CO and HC. The DOC converts part of the engine NOx to NO2, which reacts with the trapped soot to regenerate the filter. As engines become more fuel efficient, less waste heat enters the exhaust. This can be a disadvantage for after-treatment systems as it leads to lower catalyst operating temperatures. The CRT system regenerates passively, without addition of heat, at temperatures that are typical of diesel engine exhaust. JM recently launched the Mining CRT system which integrates CRT technology with NO2 abatement to reduce PM and tailpipe NO2 from underground diesel mining equipment. This is the first technology proven to control both PM and NO2 emissions for a cleaner, healthier working environment. The Mining CRT is also cost-effective compared to other technologies."

Jan 1, 2019

By Uwe Wilhelm

Pittini Group has contracted Danieli in 2011 for the supply and replacement of the existing EAF at Ferriere Nord Plant in Osoppo. This was a very challenging project: giving the fact that the Meltshop was operating already under very high performance level, there were many elements involved for the project to improve (reduce the amount of charges, promote highest possible chemical energy utilization, allow best optimization on existing transformer power, modification on Drop Out box and Water Cooled Duct, Hydraulic System for EAF, Scrap Bucket design to fit to new EAF with existing loading and transport system, Automation System Review and Upgrade) as well as limitations of the existing installation (limited space, lifting capacity building and cranes and the required solutions for fast shell and roof exchange). All furnace parts, as well as installation engineering, were developed and discussed carefully with the Customer to either provide proven and reliable concepts, but also to define solutions for fast installation/maintenance access and quick exchange for offline turnaround. In the end, from disassembly of existing equipment up to the first heat of the new furnace, only 38 days were necessary. First heat was made on January 24th 2013, on the 6th production day 32 heats where produced at nominal design capacity and 28 days after start up 100,000 t liquid steel have already been produced.

Jul 30, 2018

By Geoffrey Hughes

The Narragansett Bay Commission (NBC) is a regional sewer authority that serves ten communities in the Providence, Rhode Island metropolitan area. From 1992 to 1999, the NBC developed a comprehensive facilities plan to abate Combined Sewer Overflow (CSO) pollution in the Upper Narragansett Bay. The plan underwent many major evolutions during this period, most notably the addition of a stakeholder?s process by which NBC demonstrated a site-specific plan to control the pollutants and meet water quality standards. The favored solution consisted of deep tunnel storage with treatment at existing wastewater facilities that had been recently upgraded. In 1999, a final plan was accepted which included two tunnels, five CSO interceptors, twelve sewer separation projects, a wetland facility, and a wastewater treatment facility upgrade. The program is to be constructed over 20 years in three sequential phases (Figure 1). Phase I of the program includes a 4,963 m (16,284 ft) long, 7.9 m (26 ft) diameter, 70.1 m (230 ft) deep storage tunnel; seven drop shafts with connecting adits; ancillary facilities; and a pump station. Construction of Phase I began in 2001 and is expected to be operational by October 2008. This paper focuses on design and construction of the Fields Point Tunnel Pump Station (FPTPS)located at the south end of the main spine tunnel. A189 Ml/day (50 MGD) pump station is required to lift CSO flows from the tunnel to the Fields Point Wastewater Treatment Facility (FPWWTF). The pumps are to be housed in a 35.6 m × 18.6 m ×20.7 m (117 ft × 61 ft × 68 ft), 91.4 m (300 ft) deep cavern excavated in a complex meta-sedimentary rock of the Rhode Island Formation, and connected to the surface by 9.7 m (32 ft) and 3.4 m (11 ft) diameter shafts. Factors which influenced selection of the size, configuration and location of facilities included the preferred arrangement of pumps, critical aspects of site geology, and estimated cost. Technical and value engineering reviews also affected the final design. Following Notice to Proceed (NTP), concerns were raised by the contractor regarding constructability and design. Additional geotechnical investigation and independent engineering review were employed to validate the design assumptions. The cavern was successfully excavated and sup-ported in rock, completed on schedule and within budget in 2005. In 1992 the NBC retained Louis Berger Group (LBG) as Program Manager (PM) for the CSO Abatement Program. LBG thereafter formed a design team including: Jacobs Engineering Group(JEG) as the designer for underground structures and near surface collection facilities; Black and Veatch(B&V) to design the pumping system and associated facilities; Haley and Aldrich (H&A) to oversee the geotechnical program; and Malcolm Pirnie to design the system-wide instrumentation and control system. Construction management, resident engineering, and inspection services were provided by the joint venture Gilbane/Jacobs Associates (G/J).

Jan 1, 2008

By Edward W. Long

The Density Separator is basically a hindered settling classifier with automatic control features that provide steady, sharp classification irrespective of extreme variations in dry tons per hour of feed solids up to the design maximum throughput for the particular material being treated. The size and capacities of commercially available units and operating data comprise the scope of the paper. Applications of the unit for other than classification are proposed, i.e. washing and desliming.

Jan 1, 1982

By Fred C. Delabbio

The successful implementation of a new technology in an underground production mine requires many challenges to be overcome. These challenges include mine hardening of new technology, mitigation of safety risks and hazards, mine operation support, and technology transfer to mine staff. In the end, the majority of these challenges relate to the human aspects of implementation. The approach selected to overcome these challenges must be customized and appropriate for each unique situation. This paper outlines the approach used to address these challenges as part of successful implementation and resulting demonstration of the hydrogen fuel cell locomotive at the Placer Dome (CLA) Limited, Campbell Mine. This technology demonstration at Campbell Mine is critical for determining technical, regulatory and implementation aspects to be incorporated into future fuel cell prototypes such as the LHD project.

May 1, 2003

By J. Driscoll, T. Morson, Ross M. Workman

The study investigates the effectiveness of the canopy air curtain (CAC) in reducing respirable dust exposure for shuttle car and ramcar operators in underground coal mining. Field testing showed that the CAC reduced dust exposure by 11-34% overall and by 57-65% during ramcar loading by the continuous miner. These results demonstrate the CAC’s potential as a significant dust control device.

Feb 19, 2022

Approximately half of all the fuel energy used in the United states is now pro-vided by oil and natural gas. A persistent and rapid growth in energy demand during the last 3 decades has been absorbed largely by the liquid and gaseous rather than solid fuels. In 1948 the energy provided by coal was substantially the same as in 1920. Meanwhile, the use of oil and natural gas each had increased fivefold. On a per capita basis, the change is more significant. Coal consumption has dropped from about 6 tons per person to 4-1/2 tons, while oil has increased from 4-1/3 barrels to 14-1/3, and natural gas from 7,500 cubic feet to about 35,000. These facts would have only academic interest if the United States had unlimited supplies of all fuels. However, while the Nation's reserves of coal are adequate to meet our needs for centuries, those of oil and natural gas appear limited. It is obvious, therefore, that the security of our liquid-fuel position would be greatly enhanced if the supply could be based in an increasing degree on solid fuels, such as coal and oil shale, which make up more than 95 percent of our fuel reserves, instead of natural oil and gas. In addition, this would create new employment and help to stabilize the market for coal, which may be facing comparatively bleak prospects in the near future unless its position with respect to other fuels is improved.

Jan 1, 1950

The Fraser Range is composed dominantly of basic pyroxene granulites derived from basalts, many of which appear to have been vesicular and*pillowed. Acidic and basic garnet-bearing granulites are important in the west, and acidic granulites and narrow anortho- site layers are dominant in some regions east of the Fraser Range. An extensive flat-lying olivine gabbro sheet cuts the granulites, and in places has been converted to spinel-bearing meta-gabbros and pyroxene granulites. The granulites of the Fraser Range (Proterozoic) are separated from the gneisses and schists of the Goldfields regions (Archaean) by the Fraser Fault, over which there is a large gravity anomaly (gradient 20 milligals per mile). Some of the problems associated with the concentration of Cu, Ni, etc. liberated from mineral lattices during metamorphism, and other principles of metal concentration in granulite terranes, are discussed. The recognition of vesicular and pillowed zones, even though highly metamorphosed, is of fundamental importance.

Jan 1, 1969

By F. H. Deist, H. D. Small, J. D. Austin, L. F. Duvel

The development and application of a computer system to aid in the planning of production in mines by F. H. DEIST, L. F. DUVEL, J. D. AUSTIN, and H. D. SMALL Published in the Journal, December 1972. Discussion by J. W. WILSON and R. W. HAZELL Although the Mine Planning Simulation Programme was originally developed as an aid to coal-mine planning, its extreme flexibility has enabled us to simulate gold-mine planning with equal facility. The initial application of the Mine Planning Simulation Model was in a small area of a large Free State gold mine where the primary aim was to assess the applicability of the programme to the gold-mining situation.

Jan 12, 1972

By J Abols, T Hughes

The selective recovery of gold and silver from solutions containing other metals, such as copper, is possible using AuRIX«100 resin in conjunction with the Gekko Resin Column. Selectivity is driven by controlling the solution pH, which enables activities such as loading copper, gold and silver and then selectively stripping copper before gold and silver. Alternatively gold and silver can be loaded and the copper left in solution. The selective loading of gold while reducing the silver loading has also been demonstrated, opening the possibility of producing high grade gold dorT from high grade silver pregnant leach solutions. This paper reviews the AuRIX«100 resin and Gekko Resin Column Technologies, discusses the uses of AuRIX«100 in the recovery of gold and silver and the chemistry relating to several projects for which AuRIX«100 is being tested.

Jan 1, 2005

By S. Gqebe, A. Lewis, M. Rodriguez-Pascual

"Gravitational sedimentation of suspensions in various precipitation processes is hindered by colloidal stability. This is due to the high surface charge of the suspension and results in strong attraction/interaction between the ions on the particle surface and counter-ions in solution. Moreover, this strong interaction results in a charge build-up that renders the suspension stable. In order to induce gravitational sedimentation of these particles, a redistribution of ions close to the particle surface is required. We therefore sought to redistribute ions close to the particle surface by applying a magnetic field. This results in the reduction of interparticle electrostatic repulsive forces and a subsequent increase in the zeta potential of a suspension. For the purpose of this study, a copper sulphide suspension was used. Copper sulphide particles were exposed to a range of field strengths for set exposure times and their zeta potential was measured before and after exposure. All particles had an initial zeta potential value equal to or less than –40 mV prior to magnetic field exposure. A significant increase in zeta potential was observed, with values reaching a maximum of –16.5 mV when exposed to a 2 T field strength for 40 minutes. This is due to Lorentz ion shifts resulting from the Lorentz force exerted by the magnetic field on the particle surface. IntroductionMetal sulphide precipitation is a process for treating industrial waste streams with high residual concentration of mixed metal ions and acid mine drainage. This process has been reported to achieve higher metal removal compared with the industrially prevalent lime precipitation, due to the sparingly soluble nature of the metal sulphide precipitates formed. However, precipitation is governed by high levels of supersaturation which favour the formation of fine particles (Lewis, 2010). Consequently, some of the metal sulphide fines formed exhibit slow settling dynamics and thus tend to remain suspended in solution."

Jan 1, 2016

By A. Mei, F. Amadini, F. Cernera, D. Baliani, A. Flor, M. La Morgia, F. Sassi

The risk of TBM jamming because of squeezing rock mass or excessive caving (instability of the cavity) conditions is always a focal point while boring long and deep tunnels with shielded TBMs. Mechanized excavation provides a large amount of real-time data, for each machine’s parameters. Several analyses have been executed to assess the correlations between different sets of TBM parameters for the exploratory tunnel. Instead of analyzing the full dataset, a different approach is proposed, with data processed sequentially to simulate the real excavation situation. The probability distributions are recalculated together with their statistical parameters while advancing. This approach is extended also to the training of a Machine Learning model able to foresee the behavior at future rings based on past rings (using a Recurrent Neural Network). The predictions show a promising first step toward creating practical tools that can assist contractors and designers to correlate and predict TBM excavation data. These tools will assist to predict and quantify high risk situations that could arise during excavation.

Jun 13, 2023

By D. Harrington, W. J. Fene

For nearly 30 years the Bureau of Mines has contended that mine explosions can be prevented and has pointed out to the industry ways and means by which they could be avoided. The record of co2l-mine explosions • during the past fiscal ?Bar bears out the :Bureau1s contention, inasmuch as fewer men were killed by coal-mi~e e:xplosions in the United States during that year than in :gi_y corresponding 12 months in the history of coal mining in the United States, insofar as records are available; and more than a year has elapsed since·a major explosion (in which five or more men were killed) has occurred, this being t.1-J.e first continuous 12- month period without a major coal-mine explosion disaster in the United States in more than 60 years. The methods of preventing mine e:iiplosions are well known to experienced, well-informed persons cngnged in coal mining. Despite this knowledge, many coal-mine operutors continue to use practices and methods that they should know have resulted in countless explosions, and mine workers persist in following past procedure or in breaking safety rules and practices almost certain eventually to result in disaster. ' Virtually all explosions are the result of human failure, such as carelessness or neglect by officials or workers or others. These human failures can be corrected chiefly by ed.ucation and proper and adequate supervision and strict discipline. In some instances mine officials are ·lax, careless, poorl~• informed, and often incompetent; end in many instances miners have repulsed the introduction of known preventive methods because of sheer obstinacy, ignorance, heedlessness, or possibly fear that the operator was trying to o'bta.in some unfair adva.,.'1. tago or would neglect some other phase of accident or e,:plosion prevention. The freedom of the fiscal year 1938-39 from major coal-mine explosions ar..d frora any considera~le number of fat,JJ.i ties from minor explosions is a. matter for congratulation, but on the other hand. the occurrence of one rather bad e~losion in each of tho 3 calendar years 1937

Nov 1, 1939

By R. L. Bolmer

Rapid depletion of our known mineral resources has stimulated exploration for new mineral deposit. Abandoned mines or prospects may prove to be commercial in today's economy. Often it is necessary to revaluate such properties. Some of these may be inaccessible because of caving of flooding. Many, however, remain in good condition, except that over the years the air in the workings has become depleted of oxygen. Each year the Bureau of Mines receives numerous requests for aid in entering old mines, the air in which is incapable of supporting life. Requests of many individuals who wish to examine or explore-such places with the help, of the Bureau's self-contained oxygen breathing apparatus have been denied because of the hazards involved in the use of this equipment for such purposes. The distance to be traveled in irrespirable gases may be too great for safety; under favorable conditions, a round trip of 2,000 feet from fresh air is the maximum distance that may be traveled.3/ The use of such equipment is hazardous unless a team of at least 5 men thoroughly experienced in its use is provided; and when extensive traveling from. a fresh-air base is required, a reserve team should be provided.3/ Usually, the apparatus is requested for use in exploring workings having only one surface connection, as mines having more than one opening usually are more easily ventilated;,and in some natural ventilation is sufficient or can be made so by cleaning out obstructed openings.

Jan 1, 1951

By G. L. Palmer

"In 1986, anomalous sampling results for heavy minerals were obtained at various sites in Namaqualand on the west coast of the Cape Province. Drilling in 1987 at Graauwduinen penetrated up to 35 meters of heavy mineral-bearing Tertiary sands which extend several kilometers inland from the coast. The heavy mineral suite includes ilmenite, rutile, leucoxene, zircon and monazite, along with gamet, pyroxene and amphibole. Three deposits are recognized, two of which comprise the resource to be mined by Namakwa Sands Limited, a recently formed Anglo American Corporation subsidiary company.Mineable reserves in excess of 500 million tonnes have been delineated, sufficient to sustain mining for over 35 years at projected production rates. During the feasibility study, on-site investigations included test mining at various sites to assess rnineability and to provide material for metallurgical testing in a pilot plant located at the site. llmenite produced at the mine will be smelted at a new facility to be built at Saldanha Bay. Saleable products comprise titania-rich slag, pig iron, zircon and rutile.During the exploration phase, company environmental guidelines were established and monitored. The feasibility study incorporated a Class 1 Environmental Impact Report, the contents of which were made public following the principles of the Integrated Environmental Management legislation."

Jan 1, 1994

By A. A. Odunaike, E. G. Okafor, M. H. Mokwe

Microscopic Studies were performed on ore samples from the Muro banded iron ore deposit in Nigeria and the Marampa iron ore deposit in Sierra Leone. Ore characteristics that affect processing of both ores were compared with a view toward assisting mineral processing engineers in choosing the most suitable methods for upgrading the ore. The Nigerian ore contains 30% to 37% (by weight) Fe and the Sierra Leonean ore contains 34% to 51% (by weight) Fe. Hematite is the main iron mineral in both ores. The Sierra Leonean ore is relatively coarse grained (typically around 250 µm) and can be upgraded by conventional gravitational methods. In contrast, the Nigerian iron ore is fine grained and must be ground to -74 µm to liberate the hematite for recovery by flotation. Both ores contain high percentages of phosphorus and sulfur, which are above the required specifications for direct reduction and blast-furnace practice. These deleterious elements can be rejected by grinding and flotation.

Jan 1, 1999

By P. Randall, J. Ickes, S. Chattopadhyay

This study was undertaken as a part of developing treatment alternatives for waste materials, primarily waste rock and roaster tailings, from sites contaminated with mercury (Hg) mining wastes. Leaching profiles of waste rock over a range of different pH and oxidation-reduction (Eh) conditions were performed. Since iron (Fe) is present in large quantities in mining wastes, the effect of Fe on leaching of Hg was also determined. Results show that the Hg concentration increased as the pH of the suspension increased until a pH value of 10.65. Thereafter, the Hg concentration decreased sharply. The Hg concentration, in presence of Fe decreased significantly (1/10thto 1/100th). Kinetics results show a relatively slow rate of leaching in presence of ferric ions. The results obtained from the present study are being used to predict the fate and stability of Hg present in the environment, and will therefore, be useful in dictating the nature and suitability of any remediation treatment.

Jan 1, 2003